OMAP3: Add SPL support to Beagleboard
PATCH 2/2 OMAP3: Add SPL support to Beagleboard
This introduces 200MHz Micron parts timing information based on x-loader and re-organizes the file slightly for grouping. The memory init logic is also based on what x-loader does in these cases. Note that while previously u-boot would be flashed in with SW ECC in this case it now must be flashed with HW ECC.
Beagleboard rev C5, xM rev A:
Beagleboard xM rev C:
Beagleboard rev B7, C2, xM rev B:
--- arch/arm/include/asm/arch-omap3/mem.h | 24 +++++ board/ti/beagle/beagle.c | 160 ++++++++++++++++++++++++++++++++- board/ti/beagle/config.mk | 33 ------- include/configs/omap3_beagle.h | 60 ++++++++++++- 4 files changed, 242 insertions(+), 35 deletions(-) delete mode 100644 board/ti/beagle/config.mk
arch/arm/include/asm/arch-omap3/mem.h +24 -0
@@ -171,6 +171,30 @@ enum {#define MICRON_V_MR ((MICRON_WBST << 9) | (MICRON_CASL << 4) | \ (MICRON_SIL << 3) | (MICRON_BL)) + +/* Micron part (200MHz optimized) 5 ns +*/ +#define MICRON_TDAL_200 6 +#define MICRON_TDPL_200 3 +#define MICRON_TRRD_200 2 +#define MICRON_TRCD_200 3 +#define MICRON_TRP_200 3 +#define MICRON_TRAS_200 8 +#define MICRON_TRC_200 11 +#define MICRON_TRFC_200 15 +#define MICRON_V_ACTIMA_200 ((MICRON_TRFC_200 << 27) | (MICRON_TRC_200 << 22) | (MICRON_TRAS_200 << 18) \ + | (MICRON_TRP_200 << 15) | (MICRON_TRCD_200 << 12) |(MICRON_TRRD_200 << 9) | \ + (MICRON_TDPL_200 << 6) | (MICRON_TDAL_200)) + +#define MICRON_TWTR_200 2 +#define MICRON_TCKE_200 4 +#define MICRON_TXP_200 2 +#define MICRON_XSR_200 23 +#define MICRON_V_ACTIMB_200 ((MICRON_TCKE_200 << 12) | (MICRON_XSR_200 << 0)) | \ + (MICRON_TXP_200 << 8) | (MICRON_TWTR_200 << 16) +#define MICRON_ARCV_200 0x5e6 +#define MICRON_V_RFR_CTRL_200 ((MICRON_ARCV_200 << 8) | (MICRON_ARE)) +/* * NUMONYX part of IGEP v2 (165MHz optimized) 6.06ns * ACTIMA
board/ti/beagle/beagle.c +159 -1
190 lines not on this page · raw message
board/ti/beagle/config.mk deleted +0 -33
@@ -1,33 +0,0 @@ -# -# (C) Copyright 2006 -# Texas Instruments, <www.ti.com> -# -# Beagle Board uses OMAP3 (ARM-CortexA8) cpu -# see http://www.ti.com/ for more information on Texas Instruments -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# -# Physical Address: -# 8000'0000 (bank0) -# A000/0000 (bank1) -# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 -# (mem base + reserved) - -# For use with external or internal boots. -CONFIG_SYS_TEXT_BASE = 0x80008000
include/configs/omap3_beagle.h +59 -1
70 lines not on this page · raw message
Signature · 1 line
1.7.0.4
PATCH 2/2 OMAP3: Add SPL support to Beagleboard
Quoted 5 lines · Tom Rini
This introduces 200MHz Micron parts timing information based on x-loader and re-organizes the file slightly for grouping. ?The memory init logic is also based on what x-loader does in these cases. ?Note that while previously u-boot would be flashed in with SW ECC in this case it now must be flashed with HW ECC.
Arg, wasn't quite ready to post this, cursing git send-email and sending the whole series + explanation shortly.
Signature · 1 line
Tom