Skip to contentSkip to conversation

drivers: i915: Fix BLC PWM register setup

PATCH In review Simon Que 3 participants 4 messages Nov 11, 2011 – Jan 17, 2012

Subsystems (2)
lore
Share & tools
lore

Simon Que

author
#0 lore raw

PATCH 1/2 drivers: i915: Fix BLC PWM register setup

There is an error in i915_read_blc_pwm_ctl, where the register values are not being copied correctly. BLC_PWM_CTL and BLC_PWM_CTL2 are getting mixed up. This patch fixes that so that saveBLC_PWM_CTL2 and not saveBLC_PWM_CTL is copied to the BLC_PWM_CTL2 register.

---
 drivers/gpu/drm/i915/intel_panel.c |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_panel.c +2 -2
index a9e0c7b..f15388c 100644
@@ -141,8 +141,8 @@ static u32 i915_read_blc_pwm_ctl(struct drm_i915_private *dev_priv)
 			dev_priv->saveBLC_PWM_CTL2 = val;
 		} else if (val == 0) {
 			I915_WRITE(BLC_PWM_PCH_CTL2,
-				   dev_priv->saveBLC_PWM_CTL);
-			val = dev_priv->saveBLC_PWM_CTL;
+				   dev_priv->saveBLC_PWM_CTL2);
+			val = dev_priv->saveBLC_PWM_CTL2;
 		}
 	} else {
 		val = I915_READ(BLC_PWM_CTL);
Signature · 1 line
1.7.3.1
author
#1 lore raw

PATCH 2/2 drivers: i915: Default backlight PWM frequency

If the firmware did not initialize the backlight PWM registers, set up a default PWM frequency of 200 Hz. This is determined using the following formula:

freq = refclk / (128 * pwm_max)

The PWM register allows the max PWM value to be set. So we want to use the formula, where freq = 200:

pwm_max = refclk / (128 * freq)

This patch will, in the case of missing PWM register initialization values, look for the reference clock frequency. Based on that, it sets an appropriate max PWM value for a frequency of 200 Hz.

If no refclk frequency is found, the max PWM will be zero, which results in no change to the PWM registers.

---
 drivers/gpu/drm/i915/i915_reg.h    |    1 +
 drivers/gpu/drm/i915/intel_panel.c |   32 +++++++++++++++++++++++++++++---
 2 files changed, 30 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/i915_reg.h +1 -0
index 5d5def7..a832028 100644
@@ -3275,6 +3275,7 @@
 #define  PWM_POLARITY_ACTIVE_HIGH2	(0 << 28)
 
 #define BLC_PWM_PCH_CTL2	0xc8254
+#define BLC_PWM_PCH_FREQ_SHIFT	16
 
 #define PCH_PP_STATUS		0xc7200
 #define PCH_PP_CONTROL		0xc7204
drivers/gpu/drm/i915/intel_panel.c +29 -3
index f15388c..4bf2bde 100644
@@ -32,6 +32,10 @@
 
 #define PCI_LBPC 0xf4 /* legacy/combination backlight modes */
 
+/* For computing default PWM settings */
+#define DEFAULT_BACKLIGHT_PWM_FREQ   200
+#define BACKLIGHT_REFCLK_DIVISOR     128
+
 void
 intel_fixed_panel_mode(struct drm_display_mode *fixed_mode,
 		       struct drm_display_mode *adjusted_mode)
@@ -129,14 +133,32 @@ static int is_backlight_combination_mode(struct drm_device *dev)
 	return 0;
 }
 
+static u32 i915_get_default_max_backlight(struct drm_i915_private *dev_priv)
+{
+	u32 refclk_freq_mhz = 0;
+	if (HAS_PCH_SPLIT(dev_priv->dev))
+		refclk_freq_mhz = I915_READ(PCH_RAWCLK_FREQ) & RAWCLK_FREQ_MASK;
+	else if (dev_priv->lvds_use_ssc)
+		refclk_freq_mhz = dev_priv->lvds_ssc_freq;
+
+	return refclk_freq_mhz * 1000000 /
+			(BACKLIGHT_REFCLK_DIVISOR * DEFAULT_BACKLIGHT_PWM_FREQ);
+}
+
 static u32 i915_read_blc_pwm_ctl(struct drm_i915_private *dev_priv)
 {
 	u32 val;
-
-	/* Restore the CTL value if it lost, e.g. GPU reset */
-
+	/* Restore the CTL value if it was lost, e.g. GPU reset */
+	/* Use the default PWM max value if none is available. */
+	/* Note that the default max value will only be used if there is no */
+	/*   value already initialized in the PWM register by the BIOS and */
+	/*   nothing saved in dev_priv. */
 	if (HAS_PCH_SPLIT(dev_priv->dev)) {
 		val = I915_READ(BLC_PWM_PCH_CTL2);
+		if (dev_priv->saveBLC_PWM_CTL2 == 0 && val == 0)
+			dev_priv->saveBLC_PWM_CTL2 =
+				i915_get_default_max_backlight(dev_priv) <<
+				BLC_PWM_PCH_FREQ_SHIFT;
 		if (dev_priv->saveBLC_PWM_CTL2 == 0) {
 			dev_priv->saveBLC_PWM_CTL2 = val;
 		} else if (val == 0) {
@@ -146,6 +168,10 @@ static u32 i915_read_blc_pwm_ctl(struct drm_i915_private *dev_priv)
 		}
 	} else {
 		val = I915_READ(BLC_PWM_CTL);
+		if (dev_priv->saveBLC_PWM_CTL == 0 && val == 0)
+			dev_priv->saveBLC_PWM_CTL =
+				i915_get_default_max_backlight(dev_priv) <<
+				BACKLIGHT_MODULATION_FREQ_SHIFT;
 		if (dev_priv->saveBLC_PWM_CTL == 0) {
 			dev_priv->saveBLC_PWM_CTL = val;
 			dev_priv->saveBLC_PWM_CTL2 = I915_READ(BLC_PWM_CTL2);
Signature · 1 line
1.7.3.1
#2 lore raw

Re: [PATCH 2/2] drivers: i915: Default backlight PWM frequency

Hi,

Quoted 9 lines · Simon Que

If the firmware did not initialize the backlight PWM registers, set up a default PWM frequency of 200 Hz.  This is determined using the following formula:

 freq = refclk / (128 * pwm_max)

The PWM register allows the max PWM value to be set.  So we want to use the formula, where freq = 200:

Quoted 8 lines

 pwm_max = refclk / (128 * freq)

This patch will, in the case of missing PWM register initialization values, look for the reference clock frequency.  Based on that, it sets an appropriate max PWM value for a frequency of 200 Hz.

If no refclk frequency is found, the max PWM will be zero, which results in no change to the PWM registers.

I think the general approach of finding a suitable PWM setting is better this way, but you're attacking the problem at the wrong level.

There is already a place to hook in this in intel_panel_get_max_backlight(): Do it there in the "XXX add code" case, have the helper update the dev_priv fields to the calculated max and call i915_read_blc_pwm_ctl() again to program said fields.

-Olof

#3 lore raw
In reply to Simon Que
Quoted 6 lines · Simon Que

There is an error in i915_read_blc_pwm_ctl, where the register values are not being copied correctly. BLC_PWM_CTL and BLC_PWM_CTL2 are getting mixed up. This patch fixes that so that saveBLC_PWM_CTL2 and not saveBLC_PWM_CTL is copied to the BLC_PWM_CTL2 register.

Patch 1 here looks good to me.Queued for -next, thanks for the patch. -Daniel

Signature · 3 lines
Daniel Vetter
Mail: [email protected]
Mobile: +41 (0)79 365 57 48