Trying to understand alsa
Hi people, i'm trying to understand alsa....
I have an application that works using 512 sample packets of 22050Hz 16 bit mono audio. The 'receiver' takes many audio streams from a network via UDP, at the moment it pipes them into pulse.
Can alsa buffer audio. At the moment every time I and set an audio buffer size I get a negative response from snd_pcm_hw_params_set_buffer_size . I'm somewhat confused about the units alsa uses ...
What I want to do is tell ALSA to hold a buffer of 3 of my packets (3 x 1024Bytes, thats 512 x 16 bit samples) while I feed extra packets (1K Byte, 512 samples per buffer) in for playback. The packets are arriving at roughly the correct rate, I just need a buffer to iron out any jitter in network transmit, do I have to do this myself ?
Can somebody help by telling me which numbers I push into which places to make it work ?
At the moment I get i keep getting a broken pipe, if I underrun how can I make it just wait for me ?
I only code in plain old C at the moment.
Many thanks for any help/advice anyone can offer.
Jon
Quoted 5 lines · Jonathan Andrews
What I want to do is tell ALSA to hold a buffer of 3 of my packets (3 x 1024Bytes, thats 512 x 16 bit samples) while I feed extra packets (1K Byte, 512 samples per buffer) in for playback. The packets are arriving at roughly the correct rate, I just need a buffer to iron out any jitter in network transmit, do I have to do this myself ?
Unless data is arriving on average at *exactly* the sample rate of the ALSA device your buffering will sooner or later underrun or overrun. ALSA itself can't handle this use case, it requires adaptive resampling and it's not easy.
Ciao,
Signature · 3 lines
FA Vor uns liegt ein weites Tal, die Sonne scheint - ein Glitzerstrahl.
Quoted 9 lines · Jonathan Andrews
I have an application that works using 512 sample packets of 22050Hz 16 bit mono audio. The 'receiver' takes many audio streams from a network via UDP, at the moment it pipes them into pulse.
Can alsa buffer audio. At the moment every time I and set an audio buffer size I get a negative response from
snd_pcm_hw_params_set_buffer_size. I'm somewhat confused about the units alsa uses ...
You don't want to over-specify your requirements. You require a buffer size of "at least" 3 * 512 frames. So use set_buffer_size_min(). Otherwise ALSA will try to set exactly that buffer size, which can fail.
Check the function signatures for units. Notice that set_buffer_size*() all take snd_pcm_uframes_t, that is, the number of frames you want to store. In ALSA terms, a "frame" is a set of a single sample for every channel. Since you have mono audio, a frame and a sample are actually the same unit (for 16 bit stereo audio, 1 frame = 2 samples = 32 bits).
Quoted 6 lines
What I want to do is tell ALSA to hold a buffer of 3 of my packets (3 x 1024Bytes, thats 512 x 16 bit samples) while I feed extra packets (1K Byte, 512 samples per buffer) in for playback. The packets are arriving at roughly the correct rate, I just need a buffer to iron out any jitter in network transmit, do I have to do this myself ?
Quoted 6 lines
Can somebody help by telling me which numbers I push into which places to make it work ?
At the moment I get i keep getting a broken pipe, if I underrun how can I make it just wait for me ?
If a packet arrives very late (and one will, eventually), you will underrun. That's unavoidable. You can check for SND_PCM_STATE_XRUN from snd_pcm_state(). It's undocumented, but you need to call snd_pcm_avail_update() first to get an accurate reading from snd_pcm_state(). When an underrun occurs, recover with snd_pcm_recover() and then start writing data again.
If a packet arrives early, you'll need to check that the ALSA buffer isn't full (see snd_pcm_avail_update()), and store it within your application to write later if it is full.
There's some mostly-accurate information here:
http://0pointer.de/blog/projects/guide-to-sound-apis.html
As with all ALSA documentation, it is confusing and often incorrect, but it's probably the most helpful document I've found.
Good luck!
Andrew
A message that is not in the archive (sent off-list or not yet received): 1326410207.23310.17.camel@jonspc
Quoted 15 lines · Jonathan Andrews
Quoted 5 lines · Andrew Eikum
Quoted 4 lines · Jonathan Andrews
I have an application that works using 512 sample packets of 22050Hz 16 bit mono audio. The 'receiver' takes many audio streams from a network via UDP, at the moment it pipes them into pulse.
Quoted 8 lines
Quoted 5 lines
Can alsa buffer audio. At the moment every time I and set an audio buffer size I get a negative response from
snd_pcm_hw_params_set_buffer_size. I'm somewhat confused about the units alsa uses ...You don't want to over-specify your requirements. You require a buffer size of "at least" 3 * 512 frames. So use
set_buffer_size_min().
Quoted 7 lines
I cant find any reference to "
set_buffer_size_min" in the ALSA API documentation I have or the link you provided ?snd_pcm_hw_params_set_buffer_time_near()is the closest and that seems to take an argument in useconds.
?
http://www.alsa-project.org/alsa-doc/alsa-lib/group___p_c_m.html
The doxygen docs are split strangely. The function is documented here:
http://www.alsa-project.org/alsa-doc/alsa-lib/group___p_c_m___h_w___params.html#gb8d160039ffbbb15cb7187aa9ffae462
I find keeping the alsa-lib source on hand for quick grepping is often helpful.
Andrew