Skip to contentSkip to conversation

Logical device name for 4-channel microphones?

DISCUSSION Tanu Kaskinen 3 participants 6 messages Apr 21, 2012 – Apr 25, 2012

lore
Share & tools
lore
#0 lore raw

Hi,

What is the best source of information about device names ("front", "surround40" etc)? Is it the DeviceNames wiki page[1]? That page was slightly out of date, so I updated and expanded it (review would be welcome).

I'm looking for information specifically about capture device names. The wiki page didn't help me there, as it only listed playback device names. My problem is that I'd like to make Pulseaudio handle 4-channel webcam microphones[2], but I'm not aware of any input device names for 4-channel devices. Are there such device names? If not, what should be done?

Pulseaudio could just use "hw", but I'd prefer there to be a standard device name for 4-channel mics. AFAIK, at playback side, some surround implementations are using multiple devices on one card, and using "hw" wouldn't work in those cases, while e.g. "surround40" can use the multiple devices behind the scenes. I would guess that the same could be the case with some multichannel microphones, and therefore a logical name like "fourchannelmic" would be better than using "hw".

[1] http://www.alsa-project.org/main/index.php/DeviceNames
[2] https://bugs.freedesktop.org/show_bug.cgi?id=45813

Signature · 1 line
Tanu
#1 lore raw
Quoted 3 lines · Tanu Kaskinen

My problem is that I'd like to make Pulseaudio handle 4-channel webcam microphones[2], but I'm not aware of any input device names for 4-channel devices. Are there such device names?

These device name are useful only for device types that are generic enough. Four-channel microphones aren't.

Regards,
Clemens

#2 lore raw

At Tue, 24 Apr 2012 16:08:45 +0200,

Quoted 8 lines · Clemens Ladisch
Quoted 3 lines · Tanu Kaskinen

My problem is that I'd like to make Pulseaudio handle 4-channel webcam microphones[2], but I'm not aware of any input device names for 4-channel devices. Are there such device names?

These device name are useful only for device types that are generic enough. Four-channel microphones aren't.

Hm, we have already surround51 or such specific one, so it's not too bad to have a definition for multi-channel mics. OTOH, surround51 & co were the possible cause of confusions, as there are way too many surround types. A generic type with the channels argument might be more generic?

In anyway, I think it's fine to define some new generic name.

Takashi

#3 lore raw
Quoted 17 lines · Takashi Iwai

At Tue, 24 Apr 2012 16:08:45 +0200,

Quoted 8 lines · Clemens Ladisch
Quoted 3 lines · Tanu Kaskinen

My problem is that I'd like to make Pulseaudio handle 4-channel webcam microphones[2], but I'm not aware of any input device names for 4-channel devices. Are there such device names?

These device name are useful only for device types that are generic enough. Four-channel microphones aren't.

Hm, we have already surround51 or such specific one, so it's not too bad to have a definition for multi-channel mics. OTOH, surround51 & co were the possible cause of confusions, as there are way too many surround types. A generic type with the channels argument might be more generic?

Quoted 3 lines

In anyway, I think it's fine to define some new generic name.

From Pulseaudio point of view using "hw" should be fine if you can

guarantee that any current or future 4-channel mics can be opened in the 4-channel mode using the "hw:CARD" device name. I'm just worried that there might be cards that split the four channels to e.g. two stereo devices, "hw:CARD,0" and "hw:CARD,1", and then "hw:CARD" won't work. I might be mistaken, but aren't there some such cases with playback, which have to be opened with the "surround" device names to get all the channels?

The "surround" devices also guarantee some specific channel mapping, which may not match what "hw" uses, which is another reason to prefer "surround" over "hw", but I don't think this applies to input side. Therefore, the only possible problem that I can see with "hw" is that it might not provide all channels.

Signature · 1 line
Tanu
#4 lore raw

At Tue, 24 Apr 2012 18:28:14 +0300,

Quoted 19 lines · Tanu Kaskinen
Quoted 17 lines · Takashi Iwai

At Tue, 24 Apr 2012 16:08:45 +0200,

Quoted 8 lines · Clemens Ladisch
Quoted 3 lines · Tanu Kaskinen

My problem is that I'd like to make Pulseaudio handle 4-channel webcam microphones[2], but I'm not aware of any input device names for 4-channel devices. Are there such device names?

These device name are useful only for device types that are generic enough. Four-channel microphones aren't.

Hm, we have already surround51 or such specific one, so it's not too bad to have a definition for multi-channel mics. OTOH, surround51 & co were the possible cause of confusions, as there are way too many surround types. A generic type with the channels argument might be more generic?

Quoted 5 lines
Quoted 1 line

In anyway, I think it's fine to define some new generic name.

From Pulseaudio point of view using "hw" should be fine if you can guarantee that any current or future 4-channel mics can be opened in the 4-channel mode using the "hw:CARD" device name.

Such a thing can be never guaranteed with "hw" :)
The hw provides nothing but what kernel driver provides. And the hardware might be a link of two stereo streams.

Takashi

Quoted 16 lines

I'm just worried that
there might be cards that split the four channels to e.g. two stereo devices, "hw:CARD,0" and "hw:CARD,1", and then "hw:CARD" won't work. I might be mistaken, but aren't there some such cases with playback, which have to be opened with the "surround" device names to get all the channels?

The "surround" devices also guarantee some specific channel mapping, which may not match what "hw" uses, which is another reason to prefer "surround" over "hw", but I don't think this applies to input side. Therefore, the only possible problem that I can see with "hw" is that it might not provide all channels.

Signature · 1 line
Tanu
#5 lore raw
In reply to Takashi Iwai
Quoted 11 lines · Takashi Iwai

At Tue, 24 Apr 2012 16:08:45 +0200,

Quoted 8 lines · Clemens Ladisch
Quoted 3 lines · Tanu Kaskinen

My problem is that I'd like to make Pulseaudio handle 4-channel webcam microphones[2], but I'm not aware of any input device names for 4-channel devices. Are there such device names?

These device name are useful only for device types that are generic enough. Four-channel microphones aren't.

Quoted 7 lines

Hm, we have already surround51 or such specific one, so it's not too bad to have a definition for multi-channel mics. OTOH, surround51 & co were the possible cause of confusions, as there are way too many surround types. A generic type with the channels argument might be more generic?

In anyway, I think it's fine to define some new generic name.

Alright then, what should be the name? Here's one proposal:
"4channelinput".

Signature · 1 line
Tanu