cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.
PATCH 1/1 cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.
Hi,
This adds to the documenation to explain how to use the kwbimage.cfg file necessary to generate an image with prefixed board setup values necessary for the kirkwood boards.
--- doc/README.kwbimage | 17 ++++++++++++++--- 1 files changed, 14 insertions(+), 3 deletions(-)
doc/README.kwbimage +14 -3
@@ -25,13 +25,24 @@ for ex. -T kwbimage -a 0x00600000 -e 0x00600000 \ -d u-boot.bin u-boot.kwb + kwbimage support available with mkimage utility will generate kirkwood boot -image that can be flashed on the board NAND/SPI flash +image that can be flashed on the board NAND/SPI flash. The make target +which uses mkimage to produce such an image is "u-boot.kwb". For example: + + export BUILD_DIR=/tmp/build + make distclean + make yourboard_config + make $BUILD_DIR/u-boot.kwb + Board specific configuration file specifications: ------------------------------------------------ -1. This file must present in the $(BOARDDIR) and the name should be - kwbimage.cfg (since this is used in Makefile) +1. This file must present in the $(BOARDDIR). The default name is + kwbimage.cfg. The name can be set as part of the full path + to the file using CONFIG_SYS_KWD_CONFIG (probably in + include/configs/<yourboard>.h). The path should look like: + $(SRCTREE)/$(CONFIG_BOARDDIR)/<yourkwbimagename>.cfg 2. This file can have empty lines and lines starting with "#" as first character to put comments 3. This file can have configuration command lines as mentioned below,
Signature · 1 line
1.7.2.5
PATCH 1/1 cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.
Quoted 55 lines
-----Original Message-----
From: Karl O. Pinc [mailto:kop at meme.com]
Sent: 03 August 2012 08:22
To: Prafulla Wadaskar; u-boot at lists.denx.de
Cc: Karl O. Pinc
Subject: [PATCH] cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.Hi,
This adds to the documenation to explain how to use the kwbimage.cfg file necessary to generate an image with prefixed board setup values necessary for the kirkwood boards.
Signed-off-by Karl O. Pinc <[email protected]>--- doc/README.kwbimage | 17 ++++++++++++++--- 1 files changed, 14 insertions(+), 3 deletions(-)doc/README.kwbimage +1
-0@@ -25,13 +25,24 @@ for ex. -T kwbimage -a 0x00600000 -e 0x00600000 \ -d u-boot.bin u-boot.kwb + kwbimage support available with mkimage utility will generatekirkwood boot
doc/README.kwbimage +1
-1-image that can be flashed on the board NAND/SPI flash +image that can be flashed on the board NAND/SPI flash. The maketarget
+which uses mkimage to produce such an image is "u-boot.kwb". For example:doc/README.kwbimage +11
-2+ + export BUILD_DIR=/tmp/build + make distclean + make yourboard_config + make $BUILD_DIR/u-boot.kwb + Board specific configuration file specifications: ------------------------------------------------ -1. This file must present in the $(BOARDDIR) and the name should be - kwbimage.cfg (since this is used in Makefile) +1. This file must present in the $(BOARDDIR). The default name is + kwbimage.cfg. The name can be set as part of the full path + to the file using CONFIG_SYS_KWD_CONFIG (probably in + include/configs/<yourboard>.h). The path should look like: + $(SRCTREE)/$(CONFIG_BOARDDIR)/<yourkwbimagename>.cfg 2. This file can have empty lines and lines starting with "#" as
Quoted 4 lines
first
character to put comments
3. This file can have configuration command lines as mentioned below,
--
Acked by: Prafulla Wadaskar <[email protected]>
I will pull this patch latter.
Regards...
Prafulla . . .
PATCH 1/1 cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.
In reply to Karl O. PincQuoted 68 lines
-----Original Message-----
From: Prafulla Wadaskar
Sent: 03 August 2012 11:58
To: 'Karl O. Pinc'; u-boot at lists.denx.de
Subject: RE: [PATCH] cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.Quoted 41 lines
-----Original Message-----
From: Karl O. Pinc [mailto:kop at meme.com]
Sent: 03 August 2012 08:22
To: Prafulla Wadaskar; u-boot at lists.denx.de
Cc: Karl O. Pinc
Subject: [PATCH] cosmetic: Better explain how to use the kirkwood kwbimage.cfg file.Hi,
This adds to the documenation to explain how to use the kwbimage.cfg file necessary to generate an image with prefixed board setup values necessary for the kirkwood boards.
Signed-off-by Karl O. Pinc <[email protected]>--- doc/README.kwbimage | 17 ++++++++++++++--- 1 files changed, 14 insertions(+), 3 deletions(-)doc/README.kwbimage +1
-0@@ -25,13 +25,24 @@ for ex. -T kwbimage -a 0x00600000 -e 0x00600000 \ -d u-boot.bin u-boot.kwb + kwbimage support available with mkimage utility will generatekirkwood boot
doc/README.kwbimage +1
-1-image that can be flashed on the board NAND/SPI flash +image that can be flashed on the board NAND/SPI flash. The maketarget
+which uses mkimage to produce such an image is "u-boot.kwb". For example:doc/README.kwbimage +5
-0+ + export BUILD_DIR=/tmp/build + make distclean + make yourboard_config + make $BUILD_DIR/u-boot.kwbdoc/README.kwbimage for ex.
Quoted 10 lines
doc/README.kwbimage +5
-2+ Board specific configuration file specifications: ------------------------------------------------ -1. This file must present in the $(BOARDDIR) and the name should be - kwbimage.cfg (since this is used in Makefile) +1. This file must present in the $(BOARDDIR). The default name is + kwbimage.cfg. The name can be set as part of the full path + to the file using CONFIG_SYS_KWD_CONFIG (probably in + include/configs/<yourboard>.h). The path should looklike:
Quoted 5 lines
+ $(SRCTREE)/$(CONFIG_BOARDDIR)/<yourkwbimagename>.cfg
2. This file can have empty lines and lines starting with "#" as
first
character to put comments
3. This file can have configuration command lines as mentioned
Quoted 6 lines
below,
Quoted 1 line
--
Acked by: Prafulla Wadaskar <[email protected]>
I will pull this patch latter.
Applied to u-boot-marvell.git master branch
Regards...
Prafulla . . .