Documentation DMA-API-HOWTO.txt Add dma mapping error check usage examples

index a0b6250..cf1adb4 100644
@@ -468,11 +468,46 @@ To map a single region, you do:
 	size_t size = buffer->len;
 
 	dma_handle = dma_map_single(dev, addr, size, direction);
+	if (unlikely(dma_mapping_error(dma_handle))) {
+		/*
+		 * reduce current DMA mapping usage,
+		 * delay and try again later or
+		 * reset driver.
+		 */
+		goto map_error_handling;
+	}
 
 and to unmap it:
 
 	dma_unmap_single(dev, dma_handle, size, direction);
 
+You should call dma_mapping_error() as dma_map_single() could fail and return
+error. Not all dma implementations support dma_mapping_error() interface.
+However, it is a good practice to call dma_mapping_error() interface, which
+will invoke the generic mapping error check interface. Doing so will ensure
+that the mapping code will work correctly on all dma implementations without
+any dependency on the specifics of the underlying implementation. Using the
+returned address without checking for errors could result in failures ranging
+from panics to silent data corruption. Couple of example of incorrect ways to
+check for errors that make assumptions about the underlying dma implementation
+are as follows and these are applicable to dma_map_page() as well.
+
+Incorrect example 1:
+	dma_addr_t dma_handle;
+
+	dma_handle = dma_map_single(dev, addr, size, direction);
+	if ((dma_handle & 0xffff != 0) || (dma_handle >= 0x1000000)) {
+		goto map_error;
+	}
+
+Incorrect example 2:
+	dma_addr_t dma_handle;
+
+	dma_handle = dma_map_single(dev, addr, size, direction);
+	if (dma_handle == DMA_ERROR_CODE) {
+		goto map_error;
+	}
+
 You should call dma_unmap_single when the DMA activity is finished, e.g.
 from the interrupt which told you that the DMA transfer is done.
 

@@ -489,6 +524,14 @@ Specifically:
 	size_t size = buffer->len;
 
 	dma_handle = dma_map_page(dev, page, offset, size, direction);
+	if (unlikely(dma_mapping_error(dma_handle))) {
+		/*
+		 * reduce current DMA mapping usage,
+		 * delay and try again later or
+		 * reset driver.
+		 */
+		goto map_error_handling;
+	}
 
 	...
 

@@ -496,6 +539,12 @@ Specifically:
 
 Here, "offset" means byte offset within the given page.
 
+You should call dma_mapping_error() as dma_map_page() could fail and return
+error as outlined under the dma_map_single() discussion.
+
+You should call dma_unmap_page when the DMA activity is finished, e.g.
+from the interrupt which told you that the DMA transfer is done.
+
 With scatterlists, you map a region gathered from several regions by:
 
 	int i, count = dma_map_sg(dev, sglist, nents, direction);

@@ -578,6 +627,14 @@ to use the dma_sync_*() interfaces.
 		dma_addr_t mapping;
 
 		mapping = dma_map_single(cp->dev, buffer, len, DMA_FROM_DEVICE);
+		if (unlikely(dma_mapping_error(dma_handle))) {
+			/*
+			 * reduce current DMA mapping usage,
+			 * delay and try again later or
+			 * reset driver.
+			 */
+			goto map_error_handling;
+		}
 
 		cp->rx_buf = buffer;
 		cp->rx_len = len;

@@ -652,12 +709,81 @@ failure can be determined by:
 	dma_addr_t dma_handle;
 
 	dma_handle = dma_map_single(dev, addr, size, direction);
-	if (dma_mapping_error(dev, dma_handle)) {
+	if (unlikely(dma_mapping_error(dev, dma_handle))) {
+		/*
+		 * reduce current DMA mapping usage,
+		 * delay and try again later or
+		 * reset driver.
+		 */
+		goto map_error_handling;
+	}
+
+- unmap pages that are already mapped, when mapping error occurs in the middle
+  of a multiple page mapping attempt. These example are applicable to
+  dma_map_page() as well.
+
+Example 1:
+	dma_addr_t dma_handle1;
+	dma_addr_t dma_handle2;
+
+	dma_handle1 = dma_map_single(dev, addr, size, direction);
+	if (unlikely(dma_mapping_error(dev, dma_handle1))) {
+		/*
+		 * reduce current DMA mapping usage,
+		 * delay and try again later or
+		 * reset driver.
+		 */
+		goto map_error_handling1;
+	}
+	dma_handle2 = dma_map_single(dev, addr, size, direction);
+	if (dma_mapping_error(dev, dma_handle2)) {
 		/*
 		 * reduce current DMA mapping usage,
 		 * delay and try again later or
 		 * reset driver.
 		 */
+		goto map_error_handling2;
+	}
+
+	...
+
+	map_error_handling2:
+		dma_unmap_single(dma_handle1);
+	map_error_handling1:
+
+Example 2: (if buffers are allocated a loop, unmap all mapped buffers when
+	    mapping error is detected in the middle)
+
+	dma_addr_t dma_addr;
+	dma_addr_t array[DMA_BUFFERS];
+	int save_index = 0;
+
+	for (i = 0; i < DMA_BUFFERS; i++) {
+
+		...
+
+		dma_addr = dma_map_single(dev, addr, size, direction);
+		if (dma_mapping_error(dev, dma_addr)) {
+			/*
+			 * reduce current DMA mapping usage,
+			 * delay and try again later or
+			 * reset driver.
+			 */
+			goto map_error_handling;
+		}
+		array[i].dma_addr = dma_addr;
+		save_index++;
+	}
+
+	...
+
+	map_error_handling:
+
+	for (i = 0; i < save_index; i++) {
+
+		...
+
+		dma_unmap_single(array[i].dma_addr);
 	}
 
 Networking drivers must call dev_kfree_skb to free the socket buffer

index a0b6250..4a4fb29 100644
@@ -468,11 +468,46 @@ To map a single region, you do:
 	size_t size = buffer->len;
 
 	dma_handle = dma_map_single(dev, addr, size, direction);
+	if (dma_mapping_error(dma_handle)) {
+		/*
+		 * reduce current DMA mapping usage,
+		 * delay and try again later or
+		 * reset driver.
+		 */
+		goto map_error_handling;
+	}
 
 and to unmap it:
 
 	dma_unmap_single(dev, dma_handle, size, direction);
 
+You should call dma_mapping_error() as dma_map_single() could fail and return
+error. Not all dma implementations support dma_mapping_error() interface.
+However, it is a good practice to call dma_mapping_error() interface, which
+will invoke the generic mapping error check interface. Doing so will ensure
+that the mapping code will work correctly on all dma implementations without
+any dependency on the specifics of the underlying implementation. Using the
+returned address without checking for errors could result in failures ranging
+from panics to silent data corruption. Couple of example of incorrect ways to
+check for errors that make assumptions about the underlying dma implementation
+are as follows and these are applicable to dma_map_page() as well.
+
+Incorrect example 1:
+	dma_addr_t dma_handle;
+
+	dma_handle = dma_map_single(dev, addr, size, direction);
+	if ((dma_handle & 0xffff != 0) || (dma_handle >= 0x1000000)) {
+		goto map_error;
+	}
+
+Incorrect example 2:
+	dma_addr_t dma_handle;
+
+	dma_handle = dma_map_single(dev, addr, size, direction);
+	if (dma_handle == DMA_ERROR_CODE) {
+		goto map_error;
+	}
+
 You should call dma_unmap_single when the DMA activity is finished, e.g.
 from the interrupt which told you that the DMA transfer is done.
 

@@ -489,6 +524,14 @@ Specifically:
 	size_t size = buffer->len;
 
 	dma_handle = dma_map_page(dev, page, offset, size, direction);
+	if (dma_mapping_error(dma_handle)) {
+		/*
+		 * reduce current DMA mapping usage,
+		 * delay and try again later or
+		 * reset driver.
+		 */
+		goto map_error_handling;
+	}
 
 	...
 

@@ -496,6 +539,12 @@ Specifically:
 
 Here, "offset" means byte offset within the given page.
 
+You should call dma_mapping_error() as dma_map_page() could fail and return
+error as outlined under the dma_map_single() discussion.
+
+You should call dma_unmap_page when the DMA activity is finished, e.g.
+from the interrupt which told you that the DMA transfer is done.
+
 With scatterlists, you map a region gathered from several regions by:
 
 	int i, count = dma_map_sg(dev, sglist, nents, direction);

@@ -578,6 +627,14 @@ to use the dma_sync_*() interfaces.
 		dma_addr_t mapping;
 
 		mapping = dma_map_single(cp->dev, buffer, len, DMA_FROM_DEVICE);
+		if (dma_mapping_error(dma_handle)) {
+			/*
+			 * reduce current DMA mapping usage,
+			 * delay and try again later or
+			 * reset driver.
+			 */
+			goto map_error_handling;
+		}
 
 		cp->rx_buf = buffer;
 		cp->rx_len = len;

@@ -658,6 +715,75 @@ failure can be determined by:
 		 * delay and try again later or
 		 * reset driver.
 		 */
+		goto map_error_handling;
+	}
+
+- unmap pages that are already mapped, when mapping error occurs in the middle
+  of a multiple page mapping attempt. These example are applicable to
+  dma_map_page() as well.
+
+Example 1:
+	dma_addr_t dma_handle1;
+	dma_addr_t dma_handle2;
+
+	dma_handle1 = dma_map_single(dev, addr, size, direction);
+	if (dma_mapping_error(dev, dma_handle1)) {
+		/*
+		 * reduce current DMA mapping usage,
+		 * delay and try again later or
+		 * reset driver.
+		 */
+		goto map_error_handling1;
+	}
+	dma_handle2 = dma_map_single(dev, addr, size, direction);
+	if (dma_mapping_error(dev, dma_handle2)) {
+		/*
+		 * reduce current DMA mapping usage,
+		 * delay and try again later or
+		 * reset driver.
+		 */
+		goto map_error_handling2;
+	}
+
+	...
+
+	map_error_handling2:
+		dma_unmap_single(dma_handle1);
+	map_error_handling1:
+
+Example 2: (if buffers are allocated a loop, unmap all mapped buffers when
+	    mapping error is detected in the middle)
+
+	dma_addr_t dma_addr;
+	dma_addr_t array[DMA_BUFFERS];
+	int save_index = 0;
+
+	for (i = 0; i < DMA_BUFFERS; i++) {
+
+		...
+
+		dma_addr = dma_map_single(dev, addr, size, direction);
+		if (dma_mapping_error(dev, dma_addr)) {
+			/*
+			 * reduce current DMA mapping usage,
+			 * delay and try again later or
+			 * reset driver.
+			 */
+			goto map_error_handling;
+		}
+		array[i].dma_addr = dma_addr;
+		save_index++;
+	}
+
+	...
+
+	map_error_handling:
+
+	for (i = 0; i < save_index; i++) {
+
+		...
+
+		dma_unmap_single(array[i].dma_addr);
 	}
 
 Networking drivers must call dev_kfree_skb to free the socket buffer