Enable eDP PSR funcionality at HSW
Subsystems (3)
cover Enable eDP PSR funcionality at HSW
PSR is an eDP feature that allows power saving even with static image at eDP screen.
Shobit Kumar has implemented this patch series some time ago, but had no eDP panel with PSR capability to test them.
I could test and verify that this series fully identify PSR capability and enables it at HSW.
I also verified that it saves from 0.5-1W but only when in blank screen. It seems it is not really entering in sleeping mode with static image at eDP screen yet.
Please accept this series as the first part of PSR enabling while we continue working to improve its functionality.
PATCH 1/8 drm/i915: Added eDP PSR registers
From: Shobhit Kumar <[email protected]>
v2: Add support for psr perfromance counter register and corrected register names to reflect they are PSR registers. Also added bit definitions for the registers
v3: Add missing CDCLK_FREQ register needed for PSR enabling.
--- drivers/gpu/drm/i915/i915_reg.h | 47 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 47 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +47 -0
@@ -1561,6 +1561,40 @@#define BCLRPAT (pipe) _PIPE(pipe, _BCLRPAT_A, _BCLRPAT_B)#define VSYNCSHIFT (trans) _TRANSCODER(trans, _VSYNCSHIFT_A, _VSYNCSHIFT_B) +/* HSW eDP PSR registers */ +#define EDP_PSR_CTL 0x64800 +#define EDP_PSR_ENABLE (1<<31) +#define EDP_PSR_LINK_DISABLE (0<<27) +#define EDP_PSR_LINK_STANDBY (1<<27) +#define EDP_PSR_MIN_LINK_ENTRY_TIME_MASK (3<<25) +#define EDP_PSR_MIN_LINK_ENTRY_TIME_8_LINES (0<<25) +#define EDP_PSR_MIN_LINK_ENTRY_TIME_4_LINES (1<<25) +#define EDP_PSR_MIN_LINK_ENTRY_TIME_2_LINES (2<<25) +#define EDP_PSR_MIN_LINK_ENTRY_TIME_0_LINES (3<<25) +#define EDP_PSR_MAX_SLEEP_TIME_SHIFT 20 +#define EDP_PSR_SKIP_AUX_EXIT (1<<12) +#define EDP_PSR_TP1_TP2_SEL (0<<11) +#define EDP_PSR_TP1_TP3_SEL (1<<11) +#define EDP_PSR_TP2_TP3_TIME_500us (0<<8) +#define EDP_PSR_TP2_TP3_TIME_100us (1<<8) +#define EDP_PSR_TP2_TP3_TIME_2500us (2<<8) +#define EDP_PSR_TP2_TP3_TIME_0us (3<<8) +#define EDP_PSR_TP1_TIME_500us (0<<4) +#define EDP_PSR_TP1_TIME_100us (1<<4) +#define EDP_PSR_TP1_TIME_2500us (2<<4) +#define EDP_PSR_TP1_TIME_0us (3<<4) +#define EDP_PSR_IDLE_FRAME_SHIFT 0 + +#define EDP_PSR_AUX_CTL 0x64810 +#define EDP_PSR_AUX_DATA1 0x64814 +#define EDP_PSR_AUX_DATA2 0x64818 +#define EDP_PSR_AUX_DATA3 0x6481c +#define EDP_PSR_AUX_DATA4 0x64820 +#define EDP_PSR_AUX_DATA5 0x64824 +#define EDP_PSR_STATUS_CTL 0x64840 +#define EDP_PSR_STATUS_MASK (7<<29) +#define EDP_PSR_PERF_CNT 0x64844 +/* VGA port control */ #define ADPA 0x61100#define PCH_ADPA 0xe1100
@@ -1822,6 +1856,16 @@#define VIDEO_DIP_ENABLE_GMP_HSW (1 << 4)#define VIDEO_DIP_ENABLE_SPD_HSW (1 << 0) +#define VIDEO_DIP_CTL_EDP 0x6F200 +#define VIDEOP_DIP_VSC (1<<20) +#define VIDEOP_DIP_GCP (1<<16) +#define VIDEOP_DIP_AVI (1<<12) +#define VIDEOP_DIP_VS (1<<8) +#define VIDEOP_DIP_GMP (1<<4) +#define VIDEOP_DIP_SPD (1<<0) + +#define VIDEO_DIP_VSC_DATA_EDP 0x6F320 +/* Panel power sequencing */ #define PP_STATUS 0x61200#define PP_ON (1 << 31)
@@ -3463,6 +3507,9 @@#define HSW_FUSE_STRAP 0x42014#define HSW_CDCLK_LIMIT (1 << 24) +#define CDCLK_FREQ 0x46200 +#define CDCLK_FREQ_MASK 0x3ff +/* PCH */ /* south display engine interrupt: IBX */
Signature · 1 line
1.7.11.7
Re: [PATCH 1/8] drm/i915: Added eDP PSR registers
Hi
2013/1/11 Rodrigo Vivi <[email protected]>:
Quoted 24 lines
From: Shobhit Kumar <[email protected]>
v2: Add support for psr perfromance counter register and corrected register names to reflect they are PSR registers. Also added bit definitions for the registers
v3: Add missing
CDCLK_FREQregister needed for PSR enabling.Signed-off-by Sateesh Kavuri <[email protected]>Signed-off-by Shobhit Kumar <[email protected]>Signed-off-by Rodrigo Vivi <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 47 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 47 insertions(+)drivers/gpu/drm/i915/i915_reg.h +1
-0@@ -1561,6 +1561,40 @@#define BCLRPAT (pipe) _PIPE(pipe, _BCLRPAT_A, _BCLRPAT_B)#define VSYNCSHIFT (trans) _TRANSCODER(trans, _VSYNCSHIFT_A, _VSYNCSHIFT_B) +/* HSW eDP PSR registers */
drivers/gpu/drm/i915/i915_reg.h line 1574
Quoted 10 lines
drivers/gpu/drm/i915/i915_reg.h +10
-0+#define EDP_PSR_CTL 0x64800 +#define EDP_PSR_ENABLE (1<<31) +#define EDP_PSR_LINK_DISABLE (0<<27) +#define EDP_PSR_LINK_STANDBY (1<<27) +#define EDP_PSR_MIN_LINK_ENTRY_TIME_MASK (3<<25) +#define EDP_PSR_MIN_LINK_ENTRY_TIME_8_LINES (0<<25) +#define EDP_PSR_MIN_LINK_ENTRY_TIME_4_LINES (1<<25) +#define EDP_PSR_MIN_LINK_ENTRY_TIME_2_LINES (2<<25) +#define EDP_PSR_MIN_LINK_ENTRY_TIME_0_LINES (3<<25) +#define EDP_PSR_MAX_SLEEP_TIME_SHIFT 20
Or you could also do something like: #define EDP_PSR_MAX_SLEEP_TIME(x) ((x) << 20)
And maybe also #define EDP_PSR_MAX_SLEEP_TIME_MASK (0x1F << 20)
drivers/gpu/drm/i915/i915_reg.h line 1586
Quoted 12 lines
drivers/gpu/drm/i915/i915_reg.h +12
-0+#define EDP_PSR_SKIP_AUX_EXIT (1<<12) +#define EDP_PSR_TP1_TP2_SEL (0<<11) +#define EDP_PSR_TP1_TP3_SEL (1<<11) +#define EDP_PSR_TP2_TP3_TIME_500us (0<<8) +#define EDP_PSR_TP2_TP3_TIME_100us (1<<8) +#define EDP_PSR_TP2_TP3_TIME_2500us (2<<8) +#define EDP_PSR_TP2_TP3_TIME_0us (3<<8) +#define EDP_PSR_TP1_TIME_500us (0<<4) +#define EDP_PSR_TP1_TIME_100us (1<<4) +#define EDP_PSR_TP1_TIME_2500us (2<<4) +#define EDP_PSR_TP1_TIME_0us (3<<4) +#define EDP_PSR_IDLE_FRAME_SHIFT 0
Same thing here.
Quoted 15 lines
drivers/gpu/drm/i915/i915_reg.h +11
-0+ +#define EDP_PSR_AUX_CTL 0x64810 +#define EDP_PSR_AUX_DATA1 0x64814 +#define EDP_PSR_AUX_DATA2 0x64818 +#define EDP_PSR_AUX_DATA3 0x6481c +#define EDP_PSR_AUX_DATA4 0x64820 +#define EDP_PSR_AUX_DATA5 0x64824 +#define EDP_PSR_STATUS_CTL 0x64840 +#define EDP_PSR_STATUS_MASK (7<<29) +#define EDP_PSR_PERF_CNT 0x64844 +/* VGA port control */ #define ADPA 0x61100#define PCH_ADPA 0xe1100
drivers/gpu/drm/i915/i915_reg.h line 1859
Quoted 4 lines
drivers/gpu/drm/i915/i915_reg.h +1
-0@@ -1822,6 +1856,16 @@#define VIDEO_DIP_ENABLE_GMP_HSW (1 << 4)#define VIDEO_DIP_ENABLE_SPD_HSW (1 << 0) +#define VIDEO_DIP_CTL_EDP 0x6F200
This is not needed. Take a look at HSW_VIDEO_DIP_CTL_A and the macro HSW_TVIDEO_DIP_CTL. You need to make the HSW_TVIDEO_DIP_CTL macro use cpu_transcoder instead of pipe. You can use previous patches like this one as example:
http://lists.freedesktop.org/archives/intel-gfx/2012-October/020907.html
drivers/gpu/drm/i915/i915_reg.h line 1860
Quoted 1 line
drivers/gpu/drm/i915/i915_reg.h +1
-0+#define VIDEOP_DIP_VSC (1<<20)
See VIDEO_DIP_ENABLE_VSC_HSW.
drivers/gpu/drm/i915/i915_reg.h line 1861
Quoted 1 line
drivers/gpu/drm/i915/i915_reg.h +1
-0+#define VIDEOP_DIP_GCP (1<<16)
See VIDEO_DIP_ENABLE_GCP_HSW.
drivers/gpu/drm/i915/i915_reg.h line 1862
Quoted 1 line
drivers/gpu/drm/i915/i915_reg.h +1
-0+#define VIDEOP_DIP_AVI (1<<12)
See VIDEO_DIP_ENABLE_AVI_HSW.
drivers/gpu/drm/i915/i915_reg.h line 1863
Quoted 1 line
drivers/gpu/drm/i915/i915_reg.h +1
-0+#define VIDEOP_DIP_VS (1<<8)
See VIDEO_DIP_ENABLE_VS_HSW.
drivers/gpu/drm/i915/i915_reg.h line 1864
Quoted 1 line
drivers/gpu/drm/i915/i915_reg.h +1
-0+#define VIDEOP_DIP_GMP (1<<4)
See VIDEO_DIP_ENABLE_GMP_HSW.
drivers/gpu/drm/i915/i915_reg.h line 1865
Quoted 1 line
drivers/gpu/drm/i915/i915_reg.h +1
-0+#define VIDEOP_DIP_SPD (1<<0)
See VIDEO_DIP_ENABLE_SPD_HSW.
drivers/gpu/drm/i915/i915_reg.h line 1868
Quoted 3 lines
drivers/gpu/drm/i915/i915_reg.h +3
-0+ +#define VIDEO_DIP_VSC_DATA_EDP 0x6F320 +
Take a look at the definition of HSW_TVIDEO_DIP_CTL and similar macros. You'lll probably have to port them to use cpu_transcoder instead of pipe too.
drivers/gpu/drm/i915/i915_reg.h line 3511
Quoted 9 lines
drivers/gpu/drm/i915/i915_reg.h +2
-0/* Panel power sequencing */ #define PP_STATUS 0x61200#define PP_ON (1 << 31)@@ -3463,6 +3507,9 @@#define HSW_FUSE_STRAP 0x42014#define HSW_CDCLK_LIMIT (1 << 24) +#define CDCLK_FREQ 0x46200 +#define CDCLK_FREQ_MASK 0x3ff
Last time I checked, these registers should not be used. Please see intel_ddi_get_cdclk_freq() from intel_ddi.c.
Quoted 11 lines
drivers/gpu/drm/i915/i915_reg.h +1
-1+/* PCH */ /* south display engine interrupt: IBX */ --1.7.11.7
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 1 line
Paulo Zanoni
PATCH 2/8 drm/i915: Added SDP and VSC structures for handling PSR for eDP
In reply to Rodrigo ViviFrom: Shobhit Kumar <[email protected]>
v2: Modified and corrected the structures to be more in line for kernel coding guidelines and rebased the code on Paulo's DP patchset
v3: removing unecessary identation at DP_RECEIVER_CAP_SIZE
--- drivers/gpu/drm/i915/intel_drv.h | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
drivers/gpu/drm/i915/intel_drv.h +28 -0
@@ -371,10 +371,38 @@ struct intel_dp {int backlight_on_delay;int backlight_off_delay;struct delayed_work panel_vdd_work; +uint8_t psr_setup;bool want_panel_vdd;struct intel_connector *attached_connector; }; +/* SDP header as per eDP 1.3 spec, section 3.6 */ +struct edp_sdp_header { +u8 id; +u8 type; +u8 revision :5 ;/* Bits 0:4 */ +u8 rsvd1 :3 ;/* Bits 5:7 */ +u8 valid_payload_bytes :5 ;/* Bits 0:4 */ +u8 rsvd2 :3 ;/* Bits 5:7 */ +} __attribute__((packed)); + +/* SDP VSC header as per eDP 1.3 spec, section 3.6 */ +struct edp_vsc_psr { +struct edp_sdp_header sdp_header; +u8 unused; +u8 psr_state :1 ;/* Bit 0 */ +u8 update_rfb :1 ;/* Bit 1 */ +u8 valid_crc :1 ;/* Bit 2 */ +u8 reserved1 :5 ;/* Bits 3:7 */ +u8 crc_r_lower; +u8 crc_r_higher; +u8 crc_g_lower; +u8 crc_g_higher; +u8 crc_b_lower; +u8 crc_b_higher; +u8 reserved2[24 ]; +} __attribute__((packed)); +struct intel_digital_port {struct intel_encoder base;enum port port;
Signature · 1 line
1.7.11.7
Re: [PATCH 2/8] drm/i915: Added SDP and VSC structures for handling PSR for eDP
Quoted 4 lines · Rodrigo Vivi
From: Shobhit Kumar <[email protected]>
Signed-off-by Sateesh Kavuri <[email protected]>
Quoted 8 lines
v2: Modified and corrected the structures to be more in line for kernel coding guidelines and rebased the code on Paulo's DP patchset
Signed-off-by Shobhit Kumar <[email protected]>v3: removing unecessary identation at
DP_RECEIVER_CAP_SIZESigned-off-by Rodrigo Vivi <[email protected]>
DP spec stuff should be put into the drm core imo, i.e. into include/drm/drm_dp_helper.h Since all bitfields are u8 we also have no problems with endianess for this.
-Daniel
Quoted 54 lines
--- drivers/gpu/drm/i915/intel_drv.h | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)drivers/gpu/drm/i915/intel_drv.h +28
-0@@ -371,10 +371,38 @@ struct intel_dp {int backlight_on_delay;int backlight_off_delay;struct delayed_work panel_vdd_work; +uint8_t psr_setup;bool want_panel_vdd;struct intel_connector *attached_connector; }; +/* SDP header as per eDP 1.3 spec, section 3.6 */ +struct edp_sdp_header { +u8 id; +u8 type; +u8 revision :5 ;/* Bits 0:4 */ +u8 rsvd1 :3 ;/* Bits 5:7 */ +u8 valid_payload_bytes :5 ;/* Bits 0:4 */ +u8 rsvd2 :3 ;/* Bits 5:7 */ +} __attribute__((packed)); + +/* SDP VSC header as per eDP 1.3 spec, section 3.6 */ +struct edp_vsc_psr { +struct edp_sdp_header sdp_header; +u8 unused; +u8 psr_state :1 ;/* Bit 0 */ +u8 update_rfb :1 ;/* Bit 1 */ +u8 valid_crc :1 ;/* Bit 2 */ +u8 reserved1 :5 ;/* Bits 3:7 */ +u8 crc_r_lower; +u8 crc_r_higher; +u8 crc_g_lower; +u8 crc_g_higher; +u8 crc_b_lower; +u8 crc_b_higher; +u8 reserved2[24 ]; +} __attribute__((packed)); +struct intel_digital_port {struct intel_encoder base;enum port port;Signature · 6 lines
1.7.11.7 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch
Re: [PATCH 2/8] drm/i915: Added SDP and VSC structures for handling PSR for eDP
Quoted 10 lines · Daniel Vetter
Quoted 9 lines · Rodrigo Vivi
From: Shobhit Kumar <[email protected]>
Signed-off-by Sateesh Kavuri <[email protected]>v2: Modified and corrected the structures to be more in line for kernel coding guidelines and rebased the code on Paulo's DP patchset
Signed-off-by Shobhit Kumar <[email protected]>
Quoted 7 lines
Quoted 3 lines
v3: removing unecessary identation at
DP_RECEIVER_CAP_SIZESigned-off-by Rodrigo Vivi <[email protected]>DP spec stuff should be put into the drm core imo, i.e. into
include/drm/drm_dp_helper.hSince all bitfields are u8 we also have no problems with endianess for this.
I don't think C guarantees anything about the order of bits inside bitfieds.
Quoted 65 lines
-Daniel
Quoted 54 lines
--- drivers/gpu/drm/i915/intel_drv.h | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)drivers/gpu/drm/i915/intel_drv.h +28
-0@@ -371,10 +371,38 @@ struct intel_dp {int backlight_on_delay;int backlight_off_delay;struct delayed_work panel_vdd_work; +uint8_t psr_setup;bool want_panel_vdd;struct intel_connector *attached_connector; }; +/* SDP header as per eDP 1.3 spec, section 3.6 */ +struct edp_sdp_header { +u8 id; +u8 type; +u8 revision :5 ;/* Bits 0:4 */ +u8 rsvd1 :3 ;/* Bits 5:7 */ +u8 valid_payload_bytes :5 ;/* Bits 0:4 */ +u8 rsvd2 :3 ;/* Bits 5:7 */ +} __attribute__((packed)); + +/* SDP VSC header as per eDP 1.3 spec, section 3.6 */ +struct edp_vsc_psr { +struct edp_sdp_header sdp_header; +u8 unused; +u8 psr_state :1 ;/* Bit 0 */ +u8 update_rfb :1 ;/* Bit 1 */ +u8 valid_crc :1 ;/* Bit 2 */ +u8 reserved1 :5 ;/* Bits 3:7 */ +u8 crc_r_lower; +u8 crc_r_higher; +u8 crc_g_lower; +u8 crc_g_higher; +u8 crc_b_lower; +u8 crc_b_higher; +u8 reserved2[24 ]; +} __attribute__((packed)); +struct intel_digital_port {struct intel_encoder base;enum port port;Signature · 6 lines
1.7.11.7 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfxSignature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 2 lines
Ville Syrjälä Intel OTC
Re: [PATCH 2/8] drm/i915: Added SDP and VSC structures for handling PSR for eDP
Am 14.01.2013 12:22, schrieb Ville Syrjälä:
Quoted 13 lines · Daniel Vetter
Quoted 12 lines · Rodrigo Vivi
Quoted 11 lines
From: Shobhit Kumar <[email protected]>
Signed-off-by Sateesh Kavuri <[email protected]>v2: Modified and corrected the structures to be more in line for kernel coding guidelines and rebased the code on Paulo's DP patchset
Signed-off-by Shobhit Kumar <[email protected]>v3: removing unecessary identation at
DP_RECEIVER_CAP_SIZE
Quoted 9 lines
Quoted 5 lines
Quoted 1 line
Signed-off-by Rodrigo Vivi <[email protected]>DP spec stuff should be put into the drm core imo, i.e. into
include/drm/drm_dp_helper.hSince all bitfields are u8 we also have no problems with endianess for this.I don't think C guarantees anything about the order of bits inside bitfieds.
C11 standard, section 6.7.2.1:
"An implementation may allocate any addressable storage unit large enough to hold a bit-field. If enough space remains, a bit-field that immediately follows another bit-field in a structure shall be packed into adjacent bits of the same unit. If insufficient space remains, whether a bit-field that does not fit is put into the next unit or overlaps adjacent units is implementation-defined. The order of allocation of bit-fields within a unit (high-order to low-order or low-order to high-order) is implementation-defined. The alignment of the addressable storage unit is unspecified."
C doesn't guarantee that your u8 is a valid type for bit-fields. The only types a C compiler must support for bit-fields are bool, int, signed int and unsigned int (note that bit-fields are also the only place where the type int can be different from signed int).
Philipp
PATCH 3/8 drm/i915: Read the EDP DPCD and PSR Capability
In reply to Rodrigo ViviFrom: Shobhit Kumar <[email protected]>
v2: reuse of just created is_edp_psr and put it at right place.
--- drivers/gpu/drm/i915/intel_dp.c | 12 ++++++++++++ drivers/gpu/drm/i915/intel_drv.h | 1 + include/drm/drm_dp_helper.h | 1 + 3 files changed, 14 insertions(+)
drivers/gpu/drm/i915/intel_dp.c +12 -0
@@ -1418,6 +1418,11 @@ static void intel_post_disable_dp(struct intel_encoder *encoder) } } +static bool is_edp_psr (struct intel_dp *intel_dp) +{ +return (is_edp (intel_dp) && (intel_dp->psr_dpcd[0 ] &0x1 )); +} +static void intel_enable_dp (struct intel_encoder *encoder) {struct intel_dp *intel_dp =enc_to_intel_dp (&encoder->base);
@@ -2094,6 +2099,13 @@ intel_dp_get_dpcd(struct intel_dp *intel_dp)if (intel_dp->dpcd[DP_DPCD_REV ] ==0 )return false;/* DPCD not present */ +/* Check if the panel supports PSR */ +memset (intel_dp->psr_dpcd,0 ,EDP_PSR_RECEIVER_CAP_SIZE ); +intel_dp_aux_native_read_retry (intel_dp,DP_PSR_SUPPORT , + intel_dp->psr_dpcd, +sizeof (intel_dp->psr_dpcd)); +if (is_edp_psr (intel_dp)) +DRM_DEBUG_KMS ("Detected EDP PSR Panel.\n" );if (!(intel_dp->dpcd[DP_DOWNSTREAMPORT_PRESENT ] &DP_DWN_STRM_PORT_PRESENT ))return true;/* native DP sink */
drivers/gpu/drm/i915/intel_drv.h +1 -0
@@ -360,6 +360,7 @@ struct intel_dp {uint8_t link_bw;uint8_t lane_count;uint8_t dpcd[DP_RECEIVER_CAP_SIZE ]; +uint8_t psr_dpcd[EDP_PSR_RECEIVER_CAP_SIZE ];uint8_t downstream_ports[DP_MAX_DOWNSTREAM_PORTS ];struct i2c_adapter adapter;struct i2c_algo_dp_aux_data algo;
include/drm/drm_dp_helper.h +1 -0
@@ -335,6 +335,7 @@ u8 drm_dp_get_adjust_request_pre_emphasis(u8 link_status[DP_LINK_STATUS_SIZE], int lane);#define DP_RECEIVER_CAP_SIZE 0xf +#define EDP_PSR_RECEIVER_CAP_SIZE 2void drm_dp_link_train_clock_recovery_delay (u8 dpcd[DP_RECEIVER_CAP_SIZE ]);void drm_dp_link_train_channel_eq_delay (u8 dpcd[DP_RECEIVER_CAP_SIZE ]);
Signature · 1 line
1.7.11.7
Re: [PATCH 3/8] drm/i915: Read the EDP DPCD and PSR Capability
Hi
2013/1/11 Rodrigo Vivi <[email protected]>:
Quoted 17 lines
From: Shobhit Kumar <[email protected]>
Signed-off-by Shobhit Kumar <[email protected]>v2: reuse of just created
is_edp_psrand put it at right place.Signed-off-by Rodrigo Vivi <[email protected]>--- drivers/gpu/drm/i915/intel_dp.c | 12 ++++++++++++ drivers/gpu/drm/i915/intel_drv.h | 1 + include/drm/drm_dp_helper.h | 1 + 3 files changed, 14 insertions(+)drivers/gpu/drm/i915/intel_dp.c +0
-0
drivers/gpu/drm/i915/intel_dp.c static void intel_post_disable_dp(struct intel_encoder *encoder) · line 1423
Quoted 6 lines
drivers/gpu/drm/i915/intel_dp.c +3
-0@@ -1418,6 +1418,11 @@ static void intel_post_disable_dp(struct intel_encoder *encoder) } } +static bool is_edp_psr (struct intel_dp *intel_dp) +{ +return (is_edp (intel_dp) && (intel_dp->psr_dpcd[0 ] &0x1 ));
Bikeshedding:
Since the spec of address 0x70 says "All other values are reserved for future versions of PSR", maybe we could do something like "return (is_edp(intel_dp) && !(intel_dp->psr_dpcd[0] == 0)" ?
Quoted 50 lines
drivers/gpu/drm/i915/intel_dp.c +9
-0+} +static void intel_enable_dp (struct intel_encoder *encoder) {struct intel_dp *intel_dp =enc_to_intel_dp (&encoder->base);@@ -2094,6 +2099,13 @@ intel_dp_get_dpcd(struct intel_dp *intel_dp)if (intel_dp->dpcd[DP_DPCD_REV ] ==0 )return false;/* DPCD not present */ +/* Check if the panel supports PSR */ +memset (intel_dp->psr_dpcd,0 ,EDP_PSR_RECEIVER_CAP_SIZE ); +intel_dp_aux_native_read_retry (intel_dp,DP_PSR_SUPPORT , + intel_dp->psr_dpcd, +sizeof (intel_dp->psr_dpcd)); +if (is_edp_psr (intel_dp)) +DRM_DEBUG_KMS ("Detected EDP PSR Panel.\n" );if (!(intel_dp->dpcd[DP_DOWNSTREAMPORT_PRESENT ] &DP_DWN_STRM_PORT_PRESENT ))return true;/* native DP sink */ drivers/gpu/drm/i915/intel_drv.h +1
-0@@ -360,6 +360,7 @@ struct intel_dp {uint8_t link_bw;uint8_t lane_count;uint8_t dpcd[DP_RECEIVER_CAP_SIZE ]; +uint8_t psr_dpcd[EDP_PSR_RECEIVER_CAP_SIZE ];uint8_t downstream_ports[DP_MAX_DOWNSTREAM_PORTS ];struct i2c_adapter adapter;struct i2c_algo_dp_aux_data algo;include/drm/drm_dp_helper.h +1
-1@@ -335,6 +335,7 @@ u8 drm_dp_get_adjust_request_pre_emphasis(u8 link_status[DP_LINK_STATUS_SIZE], int lane);#define DP_RECEIVER_CAP_SIZE 0xf +#define EDP_PSR_RECEIVER_CAP_SIZE 2void drm_dp_link_train_clock_recovery_delay (u8 dpcd[DP_RECEIVER_CAP_SIZE ]);void drm_dp_link_train_channel_eq_delay (u8 dpcd[DP_RECEIVER_CAP_SIZE ]); --1.7.11.7
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 1 line
Paulo Zanoni
PATCH 4/8 drm/i915: Setup EDP PSR AUX Registers
In reply to Rodrigo ViviFrom: Shobhit Kumar <[email protected]>
--- drivers/gpu/drm/i915/intel_dp.c | 49 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 49 insertions(+)
drivers/gpu/drm/i915/intel_dp.c +49 -0
@@ -1423,6 +1423,55 @@ static bool is_edp_psr(struct intel_dp *intel_dp)return (is_edp (intel_dp) && (intel_dp->psr_dpcd[0 ] &0x1 )); } +static void intel_edp_psr_setup (struct intel_dp *intel_dp) +{ +struct drm_device *dev =intel_dp_to_dev (intel_dp); +struct drm_i915_private *dev_priv = dev->dev_private; +uint32_t aux_clock_divider; +int precharge =0x3 ; +int msg_size =5 ;/* Header(4) + Message(1) */ + +/* No need to setup if already done as these setting are persistent +* until power states are entered */ +if (intel_dp->psr_setup) +return ; + +/* Setup AUX registers */ +/* Write command on DPCD 0x0600 */ +I915_WRITE (EDP_PSR_AUX_DATA1 ,0x80060000 ); + +/* Set the state to normal operation D0 in DPCD 0x0600 */ +I915_WRITE (EDP_PSR_AUX_DATA2 ,0x01000000 ); + +if (is_cpu_edp (intel_dp)) { +if (!IS_HASWELL (dev) && (IS_GEN6 (dev) ||IS_GEN7 (dev))) + aux_clock_divider =200 ;/* SNB & IVB eDP input clock at 400Mhz */ +else +/* CDCLK divided by 2 */ + aux_clock_divider = ((I915_READ (CDCLK_FREQ ) &CDCLK_FREQ_MASK ) +1 )/2 ; + }else if (HAS_PCH_SPLIT (dev)) + aux_clock_divider =63 ;/* IRL input clock fixed at 125Mhz */ +else + aux_clock_divider =intel_hrawclk (dev) /2 ; + +I915_WRITE (EDP_PSR_AUX_CTL , + DP_AUX_CH_CTL_TIME_OUT_400us | + (msg_size <<DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT ) | + (precharge <<DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT ) | + (aux_clock_divider <<DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT )); + +/* Setup the debug register */ +I915_WRITE (EDP_PSR_DEBUG_CTL ,I915_READ (EDP_PSR_DEBUG_CTL ) | +EDP_PSR_DEBUG_MASK_MEMUP | +EDP_PSR_DEBUG_MASK_HPD ); + +/* This flag can be made to 0 from pm code so as to reinitialize the +* AUX register in case of power states, returning from which will not +* maintain the AUX register settings +*/ + intel_dp->psr_setup =1 ; +} +static void intel_enable_dp (struct intel_encoder *encoder) {struct intel_dp *intel_dp =enc_to_intel_dp (&encoder->base);
Signature · 1 line
1.7.11.7
Re: [PATCH 4/8] drm/i915: Setup EDP PSR AUX Registers
Hi
2013/1/11 Rodrigo Vivi <[email protected]>:
Quoted 55 lines
From: Shobhit Kumar <[email protected]>
Signed-off-by Shobhit Kumar <[email protected]>Reviewed-by Rodrigo Vivi <[email protected]>--- drivers/gpu/drm/i915/intel_dp.c | 49 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 49 insertions(+)drivers/gpu/drm/i915/intel_dp.c +39
-0@@ -1423,6 +1423,55 @@ static bool is_edp_psr(struct intel_dp *intel_dp)return (is_edp (intel_dp) && (intel_dp->psr_dpcd[0 ] &0x1 )); } +static void intel_edp_psr_setup (struct intel_dp *intel_dp) +{ +struct drm_device *dev =intel_dp_to_dev (intel_dp); +struct drm_i915_private *dev_priv = dev->dev_private; +uint32_t aux_clock_divider; +int precharge =0x3 ; +int msg_size =5 ;/* Header(4) + Message(1) */ + +/* No need to setup if already done as these setting are persistent +* until power states are entered */ +if (intel_dp->psr_setup) +return ; + +/* Setup AUX registers */ +/* Write command on DPCD 0x0600 */ +I915_WRITE (EDP_PSR_AUX_DATA1 ,0x80060000 ); + +/* Set the state to normal operation D0 in DPCD 0x0600 */ +I915_WRITE (EDP_PSR_AUX_DATA2 ,0x01000000 ); + +if (is_cpu_edp (intel_dp)) { +if (!IS_HASWELL (dev) && (IS_GEN6 (dev) ||IS_GEN7 (dev))) + aux_clock_divider =200 ;/* SNB & IVB eDP input clock at 400Mhz */ +else +/* CDCLK divided by 2 */ + aux_clock_divider = ((I915_READ (CDCLK_FREQ ) &CDCLK_FREQ_MASK ) +1 )/2 ; + }else if (HAS_PCH_SPLIT (dev)) + aux_clock_divider =63 ;/* IRL input clock fixed at 125Mhz */ +else + aux_clock_divider =intel_hrawclk (dev) /2 ; + +I915_WRITE (EDP_PSR_AUX_CTL , + DP_AUX_CH_CTL_TIME_OUT_400us | + (msg_size <<DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT ) | + (precharge <<DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT ) | + (aux_clock_divider <<DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT )); + +/* Setup the debug register */ + I915_WRITE(EDP_PSR_DEBUG_CTL, I915_READ(EDP_PSR_DEBUG_CTL) |
drivers/gpu/drm/i915/intel_dp.c static bool is_edp_psr(struct intel_dp *intel_dp) · line 1474
Quoted 10 lines
drivers/gpu/drm/i915/intel_dp.c +10
-0+EDP_PSR_DEBUG_MASK_MEMUP | + EDP_PSR_DEBUG_MASK_HPD); + +/* This flag can be made to 0 from pm code so as to reinitialize the +* AUX register in case of power states, returning from which will not +* maintain the AUX register settings +*/ + intel_dp->psr_setup =1 ; +} +
Looks like this function has a lot in common with intel_dp_aux_ch. Can we try to reuse its code? Maybe we could patch intel_dp_aux_ch to support using the SRD registers instead of the standard registers? Also we should probably create "intel_dp_get_aux_clock_divider()".
Quoted 10 lines
drivers/gpu/drm/i915/intel_dp.c +0
-1static void intel_enable_dp (struct intel_encoder *encoder) {struct intel_dp *intel_dp =enc_to_intel_dp (&encoder->base); --1.7.11.7
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 1 line
Paulo Zanoni
PATCH 5/8 drm/i915: VBT Parsing for the PSR Feature Block for HSW
In reply to Rodrigo ViviFrom: Shobhit Kumar <[email protected]>
Parse and store useful information in i915_dev_private
--- drivers/gpu/drm/i915/i915_drv.h | 8 ++++++++ drivers/gpu/drm/i915/intel_bios.c | 30 ++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_bios.h | 20 +++++++++++++++++++- 3 files changed, 57 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/i915_drv.h +8 -0
@@ -751,6 +751,14 @@ typedef struct drm_i915_private { } edp;bool no_aux_handshake; + +/* PSR related info from VBT */ +u8 full_link_state; +u8 wait_lines; +u8 idle_frames; +u16 wakeup_tp1; +u16 wakeup_tp2_tp3; +int crt_ddc_pin;struct drm_i915_fence_reg fence_regs[I915_MAX_NUM_FENCES ];/* assume 965 */ int fence_reg_start;/* 4 if userland hasn't ioctl'd us yet */
drivers/gpu/drm/i915/intel_bios.c +30 -0
@@ -381,6 +381,35 @@ parse_general_definitions(struct drm_i915_private *dev_priv, } } + +static void +parse_edp_psr (struct drm_i915_private *dev_priv,struct bdb_header *bdb) +{ +struct bdb_psr_features *psr; +struct bdb_lvds_options *lvds_opts; +int index =0 ; + lvds_opts =find_section (bdb,BDB_LVDS_OPTIONS ); +if (!lvds_opts) { +DRM_DEBUG_KMS ("No LVDS Options block found.\n" ); +return ; + } + + index = lvds_opts->panel_type; + + psr =find_section (bdb,BDB_PSR_FEATURES ); +if (!psr) { +DRM_DEBUG_KMS ("No PSR feature block found.\n" ); +return ; + } + + dev_priv->full_link_state = psr[index].link_disable; + dev_priv->wait_lines = psr[index].wait_lines; + dev_priv->idle_frames = psr[index].idle_frames; + dev_priv->wakeup_tp1 = psr[index].wakeup_tp1; + dev_priv->wakeup_tp2_tp3 = psr[index].wakeup_tp2; +} + +static void parse_sdvo_device_mapping (struct drm_i915_private *dev_priv,struct bdb_header *bdb)
@@ -747,6 +776,7 @@ intel_parse_bios(struct drm_device *dev)parse_device_mapping (dev_priv, bdb);parse_driver_features (dev_priv, bdb);parse_edp (dev_priv, bdb); +parse_edp_psr (dev_priv, bdb);if (bios)pci_unmap_rom (pdev, bios);
drivers/gpu/drm/i915/intel_bios.h +19 -1
@@ -80,7 +80,7 @@ struct vbios_data {#define BDB_EXT_MMIO_REGS 6#define BDB_SWF_IO 7#define BDB_SWF_MMIO 8 -#define BDB_DOT_CLOCK_TABLE 9 +#define BDB_PSR_FEATURES 9#define BDB_MODE_REMOVAL_TABLE 10#define BDB_CHILD_DEVICE_TABLE 11#define BDB_DRIVER_FEATURES 12
@@ -263,6 +263,24 @@ struct bdb_lvds_options {u8 rsvd4; } __attribute__((packed)); +struct bdb_psr_features { +/* psr_enable byte */ +u8 link_disable:1 ; +u8 require_aux:1 ; +u8 rsvd1:6 ; + +/* panel wait times */ +u8 idle_frames:4 ; +u8 wait_lines:3 ; +u8 rsvd2:1 ; + +/* TP1 wakeup time */ +u16 wakeup_tp1; + +/* TP2 wakeup time */ +u16 wakeup_tp2; +} __attribute__((packed)); +/* LFP pointer table contains entries to the struct below */ struct bdb_lvds_lfp_data_ptr {u16 fp_timing_offset;/* offsets are from start of bdb */
Signature · 1 line
1.7.11.7
Re: [PATCH 5/8] drm/i915: VBT Parsing for the PSR Feature Block for HSW
Quoted 17 lines · Rodrigo Vivi
From: Shobhit Kumar <[email protected]>
Parse and store useful information in
i915_dev_privateSigned-off-by Shobhit Kumar <[email protected]>Reviewed-by Rodrigo Vivi <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 8 ++++++++ drivers/gpu/drm/i915/intel_bios.c | 30 ++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_bios.h | 20 +++++++++++++++++++- 3 files changed, 57 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/i915_drv.h +0
-0
drivers/gpu/drm/i915/i915_drv.h typedef struct drm_i915_private { · line 760
Quoted 10 lines
drivers/gpu/drm/i915/i915_drv.h +7
-0@@ -751,6 +751,14 @@ typedef struct drm_i915_private { } edp;bool no_aux_handshake; + +/* PSR related info from VBT */ +u8 full_link_state; +u8 wait_lines; +u8 idle_frames; +u16 wakeup_tp1; +u16 wakeup_tp2_tp3;
Recently started holy war of mine: Can we pls now shovel random piles of things into dev_priv? Preferred would be if only intel_dp.c would need to care about this, otherwise a meaningful substruct (with the struct definition out of line) is the 2nd best option ...
-Daniel
Quoted 97 lines
drivers/gpu/drm/i915/i915_drv.h +1
-0+int crt_ddc_pin;struct drm_i915_fence_reg fence_regs[I915_MAX_NUM_FENCES ];/* assume 965 */ int fence_reg_start;/* 4 if userland hasn't ioctl'd us yet */ drivers/gpu/drm/i915/intel_bios.c +30
-0@@ -381,6 +381,35 @@ parse_general_definitions(struct drm_i915_private *dev_priv, } } + +static void +parse_edp_psr (struct drm_i915_private *dev_priv,struct bdb_header *bdb) +{ +struct bdb_psr_features *psr; +struct bdb_lvds_options *lvds_opts; +int index =0 ; + lvds_opts =find_section (bdb,BDB_LVDS_OPTIONS ); +if (!lvds_opts) { +DRM_DEBUG_KMS ("No LVDS Options block found.\n" ); +return ; + } + + index = lvds_opts->panel_type; + + psr =find_section (bdb,BDB_PSR_FEATURES ); +if (!psr) { +DRM_DEBUG_KMS ("No PSR feature block found.\n" ); +return ; + } + + dev_priv->full_link_state = psr[index].link_disable; + dev_priv->wait_lines = psr[index].wait_lines; + dev_priv->idle_frames = psr[index].idle_frames; + dev_priv->wakeup_tp1 = psr[index].wakeup_tp1; + dev_priv->wakeup_tp2_tp3 = psr[index].wakeup_tp2; +} + +static void parse_sdvo_device_mapping (struct drm_i915_private *dev_priv,struct bdb_header *bdb)@@ -747,6 +776,7 @@ intel_parse_bios(struct drm_device *dev)parse_device_mapping (dev_priv, bdb);parse_driver_features (dev_priv, bdb);parse_edp (dev_priv, bdb); +parse_edp_psr (dev_priv, bdb);if (bios)pci_unmap_rom (pdev, bios);drivers/gpu/drm/i915/intel_bios.h +19
-1@@ -80,7 +80,7 @@ struct vbios_data {#define BDB_EXT_MMIO_REGS 6#define BDB_SWF_IO 7#define BDB_SWF_MMIO 8 -#define BDB_DOT_CLOCK_TABLE 9 +#define BDB_PSR_FEATURES 9#define BDB_MODE_REMOVAL_TABLE 10#define BDB_CHILD_DEVICE_TABLE 11#define BDB_DRIVER_FEATURES 12@@ -263,6 +263,24 @@ struct bdb_lvds_options {u8 rsvd4; } __attribute__((packed)); +struct bdb_psr_features { +/* psr_enable byte */ +u8 link_disable:1 ; +u8 require_aux:1 ; +u8 rsvd1:6 ; + +/* panel wait times */ +u8 idle_frames:4 ; +u8 wait_lines:3 ; +u8 rsvd2:1 ; + +/* TP1 wakeup time */ +u16 wakeup_tp1; + +/* TP2 wakeup time */ +u16 wakeup_tp2; +} __attribute__((packed)); +/* LFP pointer table contains entries to the struct below */ struct bdb_lvds_lfp_data_ptr {u16 fp_timing_offset;/* offsets are from start of bdb */ Signature · 6 lines
1.7.11.7 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch
Re: [PATCH 5/8] drm/i915: VBT Parsing for the PSR Feature Block for HSW
Actually these things comes from vbt.
Maybe we could create a vbt struct to place things like this and only this vbt struct inside dev_priv..
What do you think?
Quoted 137 lines · Daniel Vetter
Quoted 17 lines · Rodrigo Vivi
From: Shobhit Kumar <[email protected]>
Parse and store useful information in
i915_dev_privateSigned-off-by Shobhit Kumar <[email protected]>Reviewed-by Rodrigo Vivi <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 8 ++++++++ drivers/gpu/drm/i915/intel_bios.c | 30 ++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_bios.h | 20 +++++++++++++++++++- 3 files changed, 57 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/i915_drv.h +0
-0drivers/gpu/drm/i915/i915_drv.h typedef struct drm_i915_private { · line 760
Quoted 10 lines
drivers/gpu/drm/i915/i915_drv.h +7
-0@@ -751,6 +751,14 @@ typedef struct drm_i915_private { } edp;bool no_aux_handshake; + +/* PSR related info from VBT */ +u8 full_link_state; +u8 wait_lines; +u8 idle_frames; +u16 wakeup_tp1; +u16 wakeup_tp2_tp3;Recently started holy war of mine: Can we pls now shovel random piles of things into
dev_priv? Preferred would be if onlyintel_dp.cwould need to care about this, otherwise a meaningful substruct (with the struct definition out of line) is the 2nd best option ...
-DanielQuoted 93 lines
drivers/gpu/drm/i915/i915_drv.h +1
-0+int crt_ddc_pin;struct drm_i915_fence_reg fence_regs[I915_MAX_NUM_FENCES ];/* assume 965 */ int fence_reg_start;/* 4 if userland hasn't ioctl'd us yet */ drivers/gpu/drm/i915/intel_bios.c +30
-0@@ -381,6 +381,35 @@ parse_general_definitions(struct drm_i915_private *dev_priv, } } + +static void +parse_edp_psr (struct drm_i915_private *dev_priv,struct bdb_header *bdb) +{ +struct bdb_psr_features *psr; +struct bdb_lvds_options *lvds_opts; +int index =0 ; + lvds_opts =find_section (bdb,BDB_LVDS_OPTIONS ); +if (!lvds_opts) { +DRM_DEBUG_KMS ("No LVDS Options block found.\n" ); +return ; + } + + index = lvds_opts->panel_type; + + psr =find_section (bdb,BDB_PSR_FEATURES ); +if (!psr) { +DRM_DEBUG_KMS ("No PSR feature block found.\n" ); +return ; + } + + dev_priv->full_link_state = psr[index].link_disable; + dev_priv->wait_lines = psr[index].wait_lines; + dev_priv->idle_frames = psr[index].idle_frames; + dev_priv->wakeup_tp1 = psr[index].wakeup_tp1; + dev_priv->wakeup_tp2_tp3 = psr[index].wakeup_tp2; +} + +static void parse_sdvo_device_mapping (struct drm_i915_private *dev_priv,struct bdb_header *bdb)@@ -747,6 +776,7 @@ intel_parse_bios(struct drm_device *dev)parse_device_mapping (dev_priv, bdb);parse_driver_features (dev_priv, bdb);parse_edp (dev_priv, bdb); +parse_edp_psr (dev_priv, bdb);if (bios)pci_unmap_rom (pdev, bios);drivers/gpu/drm/i915/intel_bios.h +19
-2@@ -80,7 +80,7 @@ struct vbios_data {#define BDB_EXT_MMIO_REGS 6#define BDB_SWF_IO 7#define BDB_SWF_MMIO 8 -#define BDB_DOT_CLOCK_TABLE 9 +#define BDB_PSR_FEATURES 9#define BDB_MODE_REMOVAL_TABLE 10#define BDB_CHILD_DEVICE_TABLE 11#define BDB_DRIVER_FEATURES 12@@ -263,6 +263,24 @@ struct bdb_lvds_options {u8 rsvd4; } __attribute__((packed)); +struct bdb_psr_features { +/* psr_enable byte */ +u8 link_disable:1 ; +u8 require_aux:1 ; +u8 rsvd1:6 ; + +/* panel wait times */ +u8 idle_frames:4 ; +u8 wait_lines:3 ; +u8 rsvd2:1 ; + +/* TP1 wakeup time */ +u16 wakeup_tp1; + +/* TP2 wakeup time */ +u16 wakeup_tp2; +} __attribute__((packed)); +/* LFP pointer table contains entries to the struct below */ struct bdb_lvds_lfp_data_ptr {u16 fp_timing_offset;/* offsets are from start of bdb */ --1.7.11.7
Quoted 4 lines
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx--
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
Signature · 2 lines
Rodrigo Vivi Blog: http://blog.vivi.eng.br
Re: [PATCH 5/8] drm/i915: VBT Parsing for the PSR Feature Block for HSW
Quoted 5 lines · Rodrigo Vivi
Actually these things comes from vbt.
Maybe we could create a vbt struct to place things like this and only this vbt struct inside
dev_priv..
What do you think?
Yeah, a vbt substruct with parsed stuff seems the sanest option. -Daniel
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch
PATCH 6/8 drm/i915: Enable/Disable PSR on HSW
In reply to Rodrigo ViviFrom: Shobhit Kumar <[email protected]>
Added eDP PSR enable functionality. This includes setting the PSR configuration over AUX, sending SDP VSC DIP over the eDP PIPE config, enabling PSR in the sink via DPCD register and finally enabling PSR on the host. PSR works only in LPSP mode, so put the PIPE_DDI in DDIA always on
This patch is heavily based on initial PSR code by Sateesh Kavuri but is quite different in implementation. Makes use of VBT parsed data and also the code has been cleaned up.
v2: fix getting base.crtc from intel_dp and fix DDI_EDP_INPUT_A_ON entry
--- drivers/gpu/drm/i915/i915_reg.h | 3 + drivers/gpu/drm/i915/intel_ddi.c | 6 +- drivers/gpu/drm/i915/intel_dp.c | 170 +++++++++++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_drv.h | 3 + 4 files changed, 181 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/i915_reg.h +3 -0
@@ -1594,6 +1594,9 @@#define EDP_PSR_STATUS_CTL 0x64840#define EDP_PSR_STATUS_MASK (7<<29)#define EDP_PSR_PERF_CNT 0x64844 +#define EDP_PSR_DEBUG_CTL 0x64860 +#define EDP_PSR_DEBUG_MASK_MEMUP (1<<26) +#define EDP_PSR_DEBUG_MASK_HPD (1<<25)/* VGA port control */ #define ADPA 0x61100
drivers/gpu/drm/i915/intel_ddi.c +5 -1
@@ -958,9 +958,13 @@ void intel_ddi_enable_pipe_func(struct drm_crtc *crtc) temp |=TRANS_DDI_PHSYNC ;if (cpu_transcoder ==TRANSCODER_EDP ) { +struct intel_dp *intel_dp =enc_to_intel_dp (encoder);switch (pipe) {case PIPE_A : - temp |=TRANS_DDI_EDP_INPUT_A_ONOFF ; +if (intel_dp->psr_dpcd[0 ] &0x1 ) + temp |=TRANS_DDI_EDP_INPUT_A_ON ; +else + temp |=TRANS_DDI_EDP_INPUT_A_ONOFF ;break ;case PIPE_B : temp |=TRANS_DDI_EDP_INPUT_B_ONOFF ;
drivers/gpu/drm/i915/intel_dp.c +170 -0
182 lines not on this page · raw message
drivers/gpu/drm/i915/intel_drv.h +3 -0
@@ -704,4 +704,7 @@ extern bool intel_ddi_connector_get_hw_state(struct intel_connector *intel_connector);extern void intel_ddi_fdi_disable (struct drm_crtc *crtc); +extern void intel_edp_enable_psr (struct intel_dp * intel_dp); +extern void intel_edp_disable_psr (struct intel_dp * intel_dp); +#endif /* __INTEL_DRV_H__ */
Signature · 1 line
1.7.11.7
PATCH 7/8 drm/i915: Added debugfs support for PSR Status
In reply to Rodrigo ViviFrom: Shobhit Kumar <[email protected]>
Added support for PSR entry counter and performance counters
v2: Add psr enabled yes/no info
--- drivers/gpu/drm/i915/i915_debugfs.c | 34 ++++++++++++++++++++++++++++++++++ 1 file changed, 34 insertions(+)
drivers/gpu/drm/i915/i915_debugfs.c +34 -0
@@ -1658,6 +1658,39 @@ static int i915_dpio_info(struct seq_file *m, void *data)return 0 ; } +static int i915_edp_psr_status (struct seq_file *m,void *data) +{ +struct drm_info_node *node = (struct drm_info_node *) m->private; +struct drm_device *dev = node->minor->dev; +struct drm_i915_private *dev_priv = dev->dev_private; +int count; +u32 psrctl, psrstat, psrperf; + +/* Bit 31 gives the PSR enabled */ + psrctl =I915_READ (EDP_PSR_CTL ); +seq_printf (m,"PSR Enabled: %s\n" , +yesno (psrctl &EDP_PSR_ENABLE )); + +/* Bits 19:16 gives the PSR entry count */ + psrstat =I915_READ (EDP_PSR_STATUS_CTL ); + count = ((psrstat >>16 ) &0xf ); + +/* Format the PSR Entry Count only for now. +* TBD: Other status information +*/ +seq_printf (m,"EDP_PSR_ENTRY_COUNT: %u\n" , count); + +/* Current PSR state */ + count = ((psrstat >>29 ) &0x7 ); +seq_printf (m,"EDP_PSR_CURRENT_STATE: 0x%x\n" , count); + +/* Perfromance counter bit 23:0 */ + psrperf = (I915_READ (EDP_PSR_PERF_CNT )) &0xffffff ; +seq_printf (m,"EDP_PSR_PERF_COUNTER: %u\n" , psrperf); + +return 0 ; +} + static ssize_t i915_wedged_read(struct file *filp, char __user *ubuf,
@@ -2131,6 +2164,7 @@ static struct drm_info_list i915_debugfs_list[] = { {"i915_swizzle_info", i915_swizzle_info, 0}, {"i915_ppgtt_info", i915_ppgtt_info, 0}, {"i915_dpio", i915_dpio_info, 0}, + {"i915_edp_psr_status", i915_edp_psr_status, 0}, };#define I915_DEBUGFS_ENTRIES ARRAY_SIZE(i915_debugfs_list)
Signature · 1 line
1.7.11.7
PATCH 8/8 drm/i915: Hook PSR functionality
In reply to Rodrigo ViviPSR must be enabled after transcoder and port are running. And it is only available for HSW.
--- drivers/gpu/drm/i915/intel_display.c | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_display.c +13 -2
@@ -3431,8 +3431,13 @@ static void haswell_crtc_enable(struct drm_crtc *crtc)intel_crtc_update_cursor (crtc, true); -for_each_encoder_on_crtc (dev, crtc, encoder) +for_each_encoder_on_crtc (dev, crtc, encoder) { encoder->enable (encoder); +if (encoder->type ==INTEL_OUTPUT_EDP ) { +struct intel_dp *intel_dp =enc_to_intel_dp (&encoder->base); +intel_edp_enable_psr (intel_dp); + } + }/* * There seems to be a race in PCH platform hw (at least on some
@@ -3459,8 +3464,14 @@ static void ironlake_crtc_disable(struct drm_crtc *crtc)if (!intel_crtc->active)return ; -for_each_encoder_on_crtc (dev, crtc, encoder) +for_each_encoder_on_crtc (dev, crtc, encoder) { +if (encoder->type ==INTEL_OUTPUT_EDP ) { +struct intel_dp *intel_dp =enc_to_intel_dp (&encoder->base); +intel_edp_disable_psr (intel_dp); + } encoder->disable (encoder); + } +intel_crtc_wait_for_pending_flips (crtc);drm_vblank_off (dev, pipe);
Signature · 1 line
1.7.11.7
Re: [PATCH 8/8] drm/i915: Hook PSR functionality
Quoted 13 lines · Rodrigo Vivi
PSR must be enabled after transcoder and port are running. And it is only available for HSW.
Signed-off-by Rodrigo Vivi <[email protected]>--- drivers/gpu/drm/i915/intel_display.c | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_display.c +0
-0
drivers/gpu/drm/i915/intel_display.c static void haswell_crtc_enable(struct drm_crtc *crtc) · line 3439
Quoted 10 lines
drivers/gpu/drm/i915/intel_display.c +5
-1@@ -3431,8 +3431,13 @@ static void haswell_crtc_enable(struct drm_crtc *crtc)intel_crtc_update_cursor (crtc, true); -for_each_encoder_on_crtc (dev, crtc, encoder) +for_each_encoder_on_crtc (dev, crtc, encoder) { encoder->enable (encoder); +if (encoder->type ==INTEL_OUTPUT_EDP ) { +struct intel_dp *intel_dp =enc_to_intel_dp (&encoder->base); +intel_edp_enable_psr (intel_dp); + }
This belongs into the dp encoder ->enable/disable callback. Really, I _hate_ such encoder/output special-casing in our crtc code ;-) So we should try to move away from such leaky abstraction, not add more ... -Daniel
Quoted 27 lines
drivers/gpu/drm/i915/intel_display.c +8
-1+ }/* * There seems to be a race in PCH platform hw (at least on some @@ -3459,8 +3464,14 @@ static void ironlake_crtc_disable(struct drm_crtc *crtc)if (!intel_crtc->active)return ; -for_each_encoder_on_crtc (dev, crtc, encoder) +for_each_encoder_on_crtc (dev, crtc, encoder) { +if (encoder->type ==INTEL_OUTPUT_EDP ) { +struct intel_dp *intel_dp =enc_to_intel_dp (&encoder->base); +intel_edp_disable_psr (intel_dp); + } encoder->disable (encoder); + } +intel_crtc_wait_for_pending_flips (crtc);drm_vblank_off (dev, pipe);Signature · 6 lines
1.7.11.7 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch
Re: [PATCH 8/8] drm/i915: Hook PSR functionality
makes sense... I was in doubt about it and I had tested it already inside ddi_enable...
I'm just not sure about having a IS_HASWELL test before calling it... I think this is the safest approach right?
Quoted 62 lines · Daniel Vetter
Quoted 13 lines · Rodrigo Vivi
PSR must be enabled after transcoder and port are running. And it is only available for HSW.
Signed-off-by Rodrigo Vivi <[email protected]>--- drivers/gpu/drm/i915/intel_display.c | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_display.c +0
-0drivers/gpu/drm/i915/intel_display.c static void haswell_crtc_enable(struct drm_crtc *crtc) · line 3439
Quoted 10 lines
drivers/gpu/drm/i915/intel_display.c +5
-1@@ -3431,8 +3431,13 @@ static void haswell_crtc_enable(struct drm_crtc *crtc)intel_crtc_update_cursor (crtc, true); -for_each_encoder_on_crtc (dev, crtc, encoder) +for_each_encoder_on_crtc (dev, crtc, encoder) { encoder->enable (encoder); +if (encoder->type ==INTEL_OUTPUT_EDP ) { +struct intel_dp *intel_dp =enc_to_intel_dp (&encoder->base); +intel_edp_enable_psr (intel_dp); + }This belongs into the dp encoder ->enable/disable callback. Really, I _hate_ such encoder/output special-casing in our crtc code ;-) So we should try to move away from such leaky abstraction, not add more ... -Daniel
Quoted 23 lines
drivers/gpu/drm/i915/intel_display.c +8
-2+ }/* * There seems to be a race in PCH platform hw (at least on some @@ -3459,8 +3464,14 @@ static void ironlake_crtc_disable(struct drm_crtc *crtc)if (!intel_crtc->active)return ; -for_each_encoder_on_crtc (dev, crtc, encoder) +for_each_encoder_on_crtc (dev, crtc, encoder) { +if (encoder->type ==INTEL_OUTPUT_EDP ) { +struct intel_dp *intel_dp =enc_to_intel_dp (&encoder->base); +intel_edp_disable_psr (intel_dp); + } encoder->disable (encoder); + } +intel_crtc_wait_for_pending_flips (crtc);drm_vblank_off (dev, pipe); --1.7.11.7
Quoted 4 lines
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx--
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
Signature · 2 lines
Rodrigo Vivi Blog: http://blog.vivi.eng.br
Re: [PATCH 8/8] drm/i915: Hook PSR functionality
Quoted 4 lines · Rodrigo Vivi
makes sense... I was in doubt about it and I had tested it already inside
ddi_enable...
I'm just not sure about having aIS_HASWELLtest before calling it... I think this is the safest approach right?
Atm ddi is hsw-only, so overkill.
-Daniel
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch