mpc5200: a4m2k: Implement custom "dynamic" watchdog support
PATCH 1/1 mpc5200: a4m2k: Implement custom "dynamic" watchdog support
This patch adds a custom U-Boot command "wdogtoggle" which enables the external hardware watchdog toggling via an GPIO pin on the a4m2k board. After issuing this commands, the watchdog will be serviced by U-Boot so that the user can use all U-Boot commands from the prompt.
--- board/a3m071/a3m071.c | 56 +++++++++++++++++++++++++++++++++++++++++++++++- include/configs/a3m071.h | 5 +++++ 2 files changed, 60 insertions(+), 1 deletion(-)
board/a3m071/a3m071.c +55 -1
@@ -255,7 +255,7 @@ void spl_board_init(void)* MPC5XXX_WU_GPIO_DIR direction is already 0 (INPUT) * set bit 0(msb) to 1 */ -setbits_be32 ((void *)MPC5XXX_WU_GPIO_ENABLE ,1 << (31 -0 )); +setbits_be32 ((void *)MPC5XXX_WU_GPIO_ENABLE ,CONFIG_WDOG_GPIO_PIN );#if defined(CONFIG_A4M2K )/* Setup USB[x] as MPCDiag[0..3] GPIO outputs */
@@ -410,3 +410,57 @@ int spl_start_uboot(void)return 1 ; }#endif + +#if defined(CONFIG_HW_WATCHDOG ) +static int watchdog_toggle; + +void hw_watchdog_reset (void ) +{ +int val; + +/* +* Check if watchdog is enabled via user command +*/ +if ((gd->flags &GD_FLG_RELOC ) && watchdog_toggle) { +/* Set direction to output */ +setbits_be32 ((void *)MPC5XXX_WU_GPIO_DIR ,CONFIG_WDOG_GPIO_PIN ); + +/* +* Toggle watchdog output +*/ + val = (in_be32 ((void *)MPC5XXX_WU_GPIO_DATA_O ) & +CONFIG_WDOG_GPIO_PIN ); +if (val) { +clrbits_be32 ((void *)MPC5XXX_WU_GPIO_DATA_O , +CONFIG_WDOG_GPIO_PIN ); + }else { +setbits_be32 ((void *)MPC5XXX_WU_GPIO_DATA_O , +CONFIG_WDOG_GPIO_PIN ); + } + } +} + +int do_wdog_toggle (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) +{ +if (argc !=2 ) + goto usage; + +if (strncmp (argv[1 ],"on" ,2 ) ==0 ) + watchdog_toggle =1 ; +else if (strncmp (argv[1 ],"off" ,3 ) ==0 ) + watchdog_toggle =0 ; +else + goto usage; + +return 0 ; +usage: +printf ("Usage: wdogtoggle %s\n" , cmdtp->usage); +return 1 ; +} + +U_BOOT_CMD ( + wdogtoggle,CONFIG_SYS_MAXARGS ,2 , do_wdog_toggle, +"toggle GPIO pin to service watchdog" , +"[on/off] - Switch watchdog toggling via GPIO pin on/off" +); +#endif
include/configs/a3m071.h +5 -0
@@ -166,6 +166,11 @@#define CONFIG_SYS_GPS_PORT_CONFIG_2 0x1005C005#endif +#define CONFIG_WDOG_GPIO_PIN GPIO_WKUP_7 +#if defined(CONFIG_A4M2K ) && !defined(CONFIG_SPL_BUILD ) +#define CONFIG_HW_WATCHDOG /* Use external HW-Watchdog */ +#endif +/* * Configuration matrix * MSB LSB
Signature · 1 line
1.8.1.2
PATCH 1/1 mpc5200: a4m2k: Implement custom "dynamic" watchdog support
Dear Stefan Roese,
Quoted 11 lines · In message <[email protected]> you wrote:
This patch adds a custom U-Boot command "wdogtoggle" which enables the external hardware watchdog toggling via an GPIO pin on the a4m2k board. After issuing this commands, the watchdog will be serviced by U-Boot so that the user can use all U-Boot commands from the prompt.
Signed-off-by Stefan Roese <[email protected]>--- board/a3m071/a3m071.c | 56 +++++++++++++++++++++++++++++++++++++++++++++++- include/configs/a3m071.h | 5 +++++ 2 files changed, 60 insertions(+), 1 deletion(-)
Applied to u-boot-mpc5xxx repo, thanks.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Pray to God, but keep rowing to shore. - Russian Proverb