ARM: proc: Add Krait proc info
Subsystems (2)
PATCH 1/1 ARM: proc: Add Krait proc info
From: Stepan Moskovchenko <[email protected]>
Add processor info for the Qualcomm, Inc. Krait family of processors, to use the generic ARMv7 initialisation procedure but explicitly enable the IDIV hardware capability flag.
--- arch/arm/mm/proc-v7.S | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/arm/mm/proc-v7.S +10 -0
@@ -434,6 +434,16 @@ __v7_ca15mp_proc_info: .size __v7_ca15mp_proc_info, . - __v7_ca15mp_proc_info /* + * Qualcomm Inc. Krait processors. + */ + .type __krait_proc_info, #object +__krait_proc_info: + .long 0x510f0400 @ Required ID value + .long 0xff0ffc00 @ Mask for ID + __v7_proc __v7_setup, hwcaps = HWCAP_IDIV + .size __krait_proc_info, . - __krait_proc_info + + /* * Match any ARMv7 processor core. */ .type __v7_proc_info, #object
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation
Hi Stephen, Stepan,
Quoted 18 lines · Stephen Boyd
From: Stepan Moskovchenko <[email protected]>
Add processor info for the Qualcomm, Inc. Krait family of processors, to use the generic ARMv7 initialisation procedure but explicitly enable the IDIV hardware capability flag.
Signed-off-by Stepan Moskovchenko <[email protected]>Signed-off-by Stephen Boyd <[email protected]>--- arch/arm/mm/proc-v7.S | 10 ++++++++++ 1 file changed, 10 insertions(+)arch/arm/mm/proc-v7.S +0
-0
arch/arm/mm/proc-v7.S __v7_ca15mp_proc_info: · line 443
Quoted 10 lines
arch/arm/mm/proc-v7.S +7
-0@@ -434,6 +434,16 @@ __v7_ca15mp_proc_info: .size __v7_ca15mp_proc_info, . - __v7_ca15mp_proc_info /* + * Qualcomm Inc. Krait processors. + */ + .type __krait_proc_info, #object +__krait_proc_info: + .long 0x510f0400 @ Required ID value + .long 0xff0ffc00 @ Mask for ID + __v7_proc __v7_setup, hwcaps = HWCAP_IDIV
I was looking at this the other day and wondered whether we could set HWCAP_IDIV in __v7_setup, depending on ID_ISAR0[27:24]. I can't immediately think why that would be difficult, but similarly there may well be a reason why we assign it like this.
Fancy taking a look?
Will
Quoted 36 lines · Will Deacon
Hi Stephen, Stepan,
Quoted 18 lines · Stephen Boyd
From: Stepan Moskovchenko <[email protected]>
Add processor info for the Qualcomm, Inc. Krait family of processors, to use the generic ARMv7 initialisation procedure but explicitly enable the IDIV hardware capability flag.
Signed-off-by Stepan Moskovchenko <[email protected]>Signed-off-by Stephen Boyd <[email protected]>--- arch/arm/mm/proc-v7.S | 10 ++++++++++ 1 file changed, 10 insertions(+)arch/arm/mm/proc-v7.S +0
-0arch/arm/mm/proc-v7.S __v7_ca15mp_proc_info: · line 443
Quoted 10 lines
arch/arm/mm/proc-v7.S +7
-0@@ -434,6 +434,16 @@ __v7_ca15mp_proc_info: .size __v7_ca15mp_proc_info, . - __v7_ca15mp_proc_info /* + * Qualcomm Inc. Krait processors. + */ + .type __krait_proc_info, #object +__krait_proc_info: + .long 0x510f0400 @ Required ID value + .long 0xff0ffc00 @ Mask for ID + __v7_proc __v7_setup, hwcaps = HWCAP_IDIVI was looking at this the other day and wondered whether we could set
HWCAP_IDIVin__v7_setup, depending on ID_ISAR0[27:24]. I can't immediately think why that would be difficult, but similarly there may well be a reason why we assign it like this.
Quoted 1 line
Fancy taking a look?
Ok I'll take a look. Should we be masking out HWCAP_IDIVT on !CONFIG_ARM_THUMB configurations?
----8<-----
arch/arm/kernel/setup.c +1 -1
@@ -484,7 +484,7 @@ static void __init setup_processor(void) list->elf_name, ENDIANNESS); elf_hwcap = list->elf_hwcap;#ifndef CONFIG_ARM_THUMB - elf_hwcap &= ~HWCAP_THUMB ; + elf_hwcap &= ~(HWCAP_THUMB |HWCAP_IDIVT );#endif feat_v6_fixup ();
Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Quoted 10 lines · Stephen Boyd
Quoted 6 lines · Will Deacon
I was looking at this the other day and wondered whether we could set
HWCAP_IDIVin__v7_setup, depending on ID_ISAR0[27:24]. I can't immediately think why that would be difficult, but similarly there may well be a reason why we assign it like this.Fancy taking a look?
Ok I'll take a look. Should we be masking out
HWCAP_IDIVTon !CONFIG_ARM_THUMB configurations?
Yes, that's not a bad idea. It makes the IDIV* caps follow what we do for the others (vfp etc) by only advertising support if the relevant CONFIG options are selected.
Will
Quoted 37 lines · Stephen Boyd
Quoted 36 lines · Will Deacon
Hi Stephen, Stepan,
Quoted 18 lines · Stephen Boyd
From: Stepan Moskovchenko <[email protected]>
Add processor info for the Qualcomm, Inc. Krait family of processors, to use the generic ARMv7 initialisation procedure but explicitly enable the IDIV hardware capability flag.
Signed-off-by Stepan Moskovchenko <[email protected]>Signed-off-by Stephen Boyd <[email protected]>--- arch/arm/mm/proc-v7.S | 10 ++++++++++ 1 file changed, 10 insertions(+)arch/arm/mm/proc-v7.S +0
-0arch/arm/mm/proc-v7.S __v7_ca15mp_proc_info: · line 443
Quoted 10 lines
arch/arm/mm/proc-v7.S +7
-0@@ -434,6 +434,16 @@ __v7_ca15mp_proc_info: .size __v7_ca15mp_proc_info, . - __v7_ca15mp_proc_info /* + * Qualcomm Inc. Krait processors. + */ + .type __krait_proc_info, #object +__krait_proc_info: + .long 0x510f0400 @ Required ID value + .long 0xff0ffc00 @ Mask for ID + __v7_proc __v7_setup, hwcaps = HWCAP_IDIVI was looking at this the other day and wondered whether we could set
HWCAP_IDIVin__v7_setup, depending on ID_ISAR0[27:24]. I can't immediately think why that would be difficult, but similarly there may well be a reason why we assign it like this.
Quoted 2 lines
Quoted 1 line
Fancy taking a look?
Ok I'll take a look.
Hmm. I wonder if we did it this way because between version B and C of DDI0406 the definition of those bits changed.
In DDI0406B we have
0 - no support
1 - support
and in DDI0406C we have
0 - no support
1 - support in Thumb
2 - support in Thumb and ARM
Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Quoted 15 lines · Stephen Boyd
Quoted 8 lines · Stephen Boyd
Quoted 6 lines · Will Deacon
I was looking at this the other day and wondered whether we could set
HWCAP_IDIVin__v7_setup, depending on ID_ISAR0[27:24]. I can't immediately think why that would be difficult, but similarly there may well be a reason why we assign it like this.Fancy taking a look?
Ok I'll take a look.
Hmm. I wonder if we did it this way because between version B and C of DDI0406 the definition of those bits changed.
In DDI0406B we have
Quoted 8 lines
0 - no support
1 - supportand in DDI0406C we have
0 - no support
1 - support in Thumb
2 - support in Thumb and ARM
Well spotted, although I think this a documentation error. I've checked both A7 and A15 and they both advertise '2' (although r0p0 TRM for A7 also gets this wrong, the CPU does the right thing).
What about the Qualcomm CPUs?
Will
Quoted 18 lines · Will Deacon
Quoted 17 lines · Stephen Boyd
Quoted 8 lines · Stephen Boyd
Quoted 6 lines · Will Deacon
I was looking at this the other day and wondered whether we could set
HWCAP_IDIVin__v7_setup, depending on ID_ISAR0[27:24]. I can't immediately think why that would be difficult, but similarly there may well be a reason why we assign it like this.Fancy taking a look?
Ok I'll take a look.
Hmm. I wonder if we did it this way because between version B and C of DDI0406 the definition of those bits changed.
In DDI0406B we have
0 - no support
1 - support
Quoted 8 lines
Quoted 5 lines
and in DDI0406C we have
0 - no support
1 - support in Thumb
2 - support in Thumb and ARMWell spotted, although I think this a documentation error. I've checked both A7 and A15 and they both advertise '2' (although r0p0 TRM for A7 also gets this wrong, the CPU does the right thing).
What about the Cortex-R7? When I google "ARM ISAR0" the first hit is
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0363e/Bgbfafej.html
and in there it just says 1.
Quoted 2 lines
What about the Qualcomm CPUs?
It's set to 1 in some of our earlier Krait CPU designs, but we corrected it later on to say 2 because the hardware actually supports the instructions in both ARM and Thumb mode. Unfortunately, we mass produced some of these chips that say 1 so we still need to do the same kind of MIDR check. I'm going to send the patchset right now with all this in it.
Signature · 2 lines
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
Quoted 24 lines · Stephen Boyd
Quoted 23 lines · Will Deacon
Quoted 22 lines · Stephen Boyd
Quoted 8 lines · Stephen Boyd
Quoted 6 lines · Will Deacon
I was looking at this the other day and wondered whether we could set
HWCAP_IDIVin__v7_setup, depending on ID_ISAR0[27:24]. I can't immediately think why that would be difficult, but similarly there may well be a reason why we assign it like this.Fancy taking a look?
Ok I'll take a look.
Hmm. I wonder if we did it this way because between version B and C of DDI0406 the definition of those bits changed.
In DDI0406B we have
0 - no support
1 - supportand in DDI0406C we have
0 - no support
1 - support in Thumb
2 - support in Thumb and ARM
Quoted 8 lines
Quoted 3 lines
Well spotted, although I think this a documentation error. I've checked both A7 and A15 and they both advertise '2' (although r0p0 TRM for A7 also gets this wrong, the CPU does the right thing).
What about the Cortex-R7? When I google "ARM ISAR0" the first hit is
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0363e/Bgbfafej.html
That appears to be an R4 TRM, but I've checked the details for R4, 5 and 7.
In R4 there is no ARM hardware divide, so the document that you linked to is correct in specifying only 0b1
In R5, ARM hardware divide was added in r0p1, and the value of ID_ISAR0[27:24] is updated to 0b10 accordingly
In R7, the TRM just refers you to the ARMARM, but the hardware guys assure me that ID_ISAR0[27:24] will be accurately 1, or 2 depending on what the processor actually supports.
Hope that helps,
Jonny