hwmon: Add driver for LM95234
Subsystems (2)
Guenter Roeck
maintainerPATCH 1/1 hwmon: Add driver for LM95234
Signed-off-by Guenter Roeck <[email protected]>
--- Documentation/hwmon/lm95234 | 36 ++ drivers/hwmon/Kconfig | 10 + drivers/hwmon/Makefile | 1 + drivers/hwmon/lm95234.c | 769 +++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 816 insertions(+) create mode 100644 Documentation/hwmon/lm95234 create mode 100644 drivers/hwmon/lm95234.c
Documentation/hwmon/lm95234 new file +35 -0
@@ -0,0 +1,36 @@ +Kernel driver lm95234 +==========+ +Supported chips: + * National Semiconductor / Texas Instruments LM95234 + Addresses scanned: I2C 0x18, 0x4d, 0x4e + Datasheet: Publicly available at the Texas Instruments website + http://www.ti.com/product/lm95234 + + +Author: Guenter Roeck <[email protected]> + +Description +----------- + +LM95234 is an 11-bit digital temperature sensor with a 2-wire System Management +Bus (SMBus) interface and TrueTherm technology that can very accurately monitor +the temperature of four remote diodes as well as its own temperature. +The four remote diodes can be external devices such as microprocessors, +graphics processors or diode-connected 2N3904s. The LM95234's TruTherm +beta compensation technology allows sensing of 90 nm or 65 nm process +thermal diodes accurately. + +All temperature values are given in millidegrees Celsius. Temperature +is provided within a range of -127 to +255 degrees (+127.875 degrees for +the internal sensor). Resolution depends on temperature input and range. + +Each sensor has its own maximum limit, but the hysteresis is common to all +channels. The hysteresis is configurable with the tem1_max_hyst attribute and +affects the hysteresis on all channels. The first two external sensors also +have a critical limit. + +The lm95234 driver can change its update interval to a fixed set of values. +It will round up to the next selectable interval. See the datasheet for exact +values. Reading sensor values more often will do no harm, but will return +'old' values.
drivers/hwmon/Kconfig +10 -0
@@ -751,6 +751,16 @@ config SENSORS_LTC4261 This driver can also be built as a module. If so, the module will be called ltc4261. +config SENSORS_LM95234 + tristate "National Semiconductor LM95234" + depends on I2C + help + If you say yes here you get support for the LM95234 temperature + sensor. + + This driver can also be built as a module. If so, the module + will be called lm95234. + config SENSORS_LM95241 tristate "National Semiconductor LM95241 and compatibles" depends on I2C
drivers/hwmon/Makefile +1 -0
@@ -86,6 +86,7 @@ obj-$(CONFIG_SENSORS_LM87) += lm87.o obj-$(CONFIG_SENSORS_LM90) += lm90.o obj-$(CONFIG_SENSORS_LM92) += lm92.o obj-$(CONFIG_SENSORS_LM93) += lm93.o +obj-$(CONFIG_SENSORS_LM95234) += lm95234.o obj-$(CONFIG_SENSORS_LM95241) += lm95241.o obj-$(CONFIG_SENSORS_LM95245) += lm95245.o obj-$(CONFIG_SENSORS_LTC4151) += ltc4151.o
drivers/hwmon/lm95234.c new file +769 -0
769 lines not on this page · raw message
Signature · 7 lines
1.7.9.7 _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors