Skip to contentSkip to conversation

regulator: ab8500: Update info->update_val only when successfully update register

PATCH Superseded Axel Lin 2 participants 2 messages Mar 28, 2013 Voltage and current regulator framework

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore

Axel Lin

author
#0 lore raw

PATCH 1/1 regulator: ab8500: Update info->update_val only when successfully update register

This fixes 2 issues:

1. Don't update info->update_val if write to the register fails.
2. Don't update info->update_val if regulator is disabled, this avoid inconsistent status between the register value and info->update_val.

---
 drivers/regulator/ab8500.c |   41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/regulator/ab8500.c +25 -16
index 12e2740..8b86604 100644
@@ -182,8 +182,8 @@ static unsigned int ab8500_regulator_get_optimum_mode(
 static int ab8500_regulator_set_mode(struct regulator_dev *rdev,
 				     unsigned int mode)
 {
-	int ret = 0;
-
+	int ret;
+	u8 update_val;
 	struct ab8500_regulator_info *info = rdev_get_drvdata(rdev);
 
 	if (info == NULL) {
@@ -191,32 +191,41 @@ static int ab8500_regulator_set_mode(struct regulator_dev *rdev,
 		return -EINVAL;
 	}
 
+	/* ab8500 regulators share mode and enable in the same register bits.
+	   off = 0b00
+	   low power mode= 0b11
+	   full powermode = 0b01
+	   (HW control mode = 0b10)
+	   Thus we don't change the mode settings when regulator is disabled.
+	 */
+	if (!info->is_enabled)
+		return 0;
+
 	switch (mode) {
 	case REGULATOR_MODE_NORMAL:
-		info->update_val = info->update_val_normal;
+		update_val = info->update_val_normal;
 		break;
 	case REGULATOR_MODE_IDLE:
-		info->update_val = info->update_val_idle;
+		update_val = info->update_val_idle;
 		break;
 	default:
 		return -EINVAL;
 	}
 
-	if (info->is_enabled) {
-		ret = abx500_mask_and_set_register_interruptible(info->dev,
+	ret = abx500_mask_and_set_register_interruptible(info->dev,
 			info->update_bank, info->update_reg,
-			info->update_mask, info->update_val);
-		if (ret < 0)
-			dev_err(rdev_get_dev(rdev),
-				"couldn't set regulator mode\n");
-
-		dev_vdbg(rdev_get_dev(rdev),
-			"%s-set_mode (bank, reg, mask, value): "
-			"0x%x, 0x%x, 0x%x, 0x%x\n",
-			info->desc.name, info->update_bank, info->update_reg,
-			info->update_mask, info->update_val);
+			info->update_mask, update_val);
+	if (ret < 0) {
+		dev_err(rdev_get_dev(rdev), "couldn't set regulator mode\n");
+		return ret;
 	}
 
+	info->update_val = update_val;
+
+	dev_vdbg(rdev_get_dev(rdev), "%s-set_mode (bank, reg, mask, value): 0x%x, 0x%x, 0x%x, 0x%x\n",
+		 info->desc.name, info->update_bank, info->update_reg,
+		 info->update_mask, info->update_val);
+
 	return ret;
 }
 
Signature · 1 line
1.7.10.4
Acked-by on v1 1/1
#1 lore raw
Quoted 7 lines · Axel Lin

This fixes 2 issues:

1. Don't update info->update_val if write to the register fails.
2. Don't update info->update_val if regulator is disabled, this avoid

    inconsistent status between the register value and info->update_val.

Looks fine, thanks.

Quoted 75 lines
---
  drivers/regulator/ab8500.c |   41 +++++++++++++++++++++++++----------------
  1 file changed, 25 insertions(+), 16 deletions(-)
drivers/regulator/ab8500.c +25 -16
index 12e2740..8b86604 100644
@@ -182,8 +182,8 @@ static unsigned int ab8500_regulator_get_optimum_mode(
  static int ab8500_regulator_set_mode(struct regulator_dev *rdev,
  				     unsigned int mode)
  {
-	int ret = 0;
-
+	int ret;
+	u8 update_val;
  	struct ab8500_regulator_info *info = rdev_get_drvdata(rdev);
 
  	if (info == NULL) {
@@ -191,32 +191,41 @@ static int ab8500_regulator_set_mode(struct regulator_dev *rdev,
  		return -EINVAL;
  	}
 
+	/* ab8500 regulators share mode and enable in the same register bits.
+	   off = 0b00
+	   low power mode= 0b11
+	   full powermode = 0b01
+	   (HW control mode = 0b10)
+	   Thus we don't change the mode settings when regulator is disabled.
+	 */
+	if (!info->is_enabled)
+		return 0;
+
  	switch (mode) {
  	case REGULATOR_MODE_NORMAL:
-		info->update_val = info->update_val_normal;
+		update_val = info->update_val_normal;
  		break;
  	case REGULATOR_MODE_IDLE:
-		info->update_val = info->update_val_idle;
+		update_val = info->update_val_idle;
  		break;
  	default:
  		return -EINVAL;
  	}
 
-	if (info->is_enabled) {
-		ret = abx500_mask_and_set_register_interruptible(info->dev,
+	ret = abx500_mask_and_set_register_interruptible(info->dev,
  			info->update_bank, info->update_reg,
-			info->update_mask, info->update_val);
-		if (ret < 0)
-			dev_err(rdev_get_dev(rdev),
-				"couldn't set regulator mode\n");
-
-		dev_vdbg(rdev_get_dev(rdev),
-			"%s-set_mode (bank, reg, mask, value): "
-			"0x%x, 0x%x, 0x%x, 0x%x\n",
-			info->desc.name, info->update_bank, info->update_reg,
-			info->update_mask, info->update_val);
+			info->update_mask, update_val);
+	if (ret < 0) {
+		dev_err(rdev_get_dev(rdev), "couldn't set regulator mode\n");
+		return ret;
  	}
 
+	info->update_val = update_val;
+
+	dev_vdbg(rdev_get_dev(rdev), "%s-set_mode (bank, reg, mask, value): 0x%x, 0x%x, 0x%x, 0x%x\n",
+		 info->desc.name, info->update_bank, info->update_reg,
+		 info->update_mask, info->update_val);
+
  	return ret;
  }