documentation:devicetree: Fix various typo in devicetree
Subsystems (9)
Device tree bindings USB I2C subsystem host drivers Arm/Microchip (AT91) SoC support +5 more subsystems
PATCH 1/1 documentation:devicetree: Fix various typo in devicetree
Fix spelling typos in Documentation/devicetree/bindings.
Signed-off-by Masanari Iida <[email protected]>
--- Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt | 2 +- Documentation/devicetree/bindings/leds/tca6507.txt | 2 +- Documentation/devicetree/bindings/metag/meta-intc.txt | 2 +- Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt | 2 +- Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt | 2 +- Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt | 2 +- Documentation/devicetree/bindings/regulator/max8997-regulator.txt | 2 +- Documentation/devicetree/bindings/usb/samsung-usbphy.txt | 2 +- 8 files changed, 8 insertions(+), 8 deletions(-)
Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt +1 -1
@@ -26,7 +26,7 @@ Required for all cases except "samsung,s3c2440-hdmiphy-i2c": - pinctrl-names: Should contain only one value - "default". Optional properties: - - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not + - samsung,i2c-slave-addr: Slave address in multi-master environment. If not specified, default value is 0. - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not specified, the default value in Hz is 100000.
Documentation/devicetree/bindings/leds/tca6507.txt +1 -1
@@ -1,4 +1,4 @@ -LEDs conected to tca6507 +LEDs connected to tca6507 Required properties: - compatible : should be : "ti,tca6507".
Documentation/devicetree/bindings/metag/meta-intc.txt +1 -1
@@ -12,7 +12,7 @@ Required properties: handle 32 interrupt sources). - interrupt-controller: The presence of this property identifies the node - as an interupt controller. No property value shall be defined. + as an interrupt controller. No property value shall be defined. - #interrupt-cells: Specifies the number of cells needed to encode an interrupt source. The type shall be a <u32> and the value shall be 2.
Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt +1 -1
@@ -1,6 +1,6 @@ * Atmel AT91 Pinmux Controller -The AT91 Pinmux Controler, enables the IC +The AT91 Pinmux Controller, enables the IC to share one PAD to several functional blocks. The sharing is done by multiplexing the PAD input/output signals. For each PAD there are up to 8 muxing options (called periph modes). Since different modules require
Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt +1 -1
@@ -5,7 +5,7 @@ controller, and pinmux/control device. Required properties: - compatible: "brcm,bcm2835-gpio" -- reg: Should contain the physical address of the GPIO module's registes. +- reg: Should contain the physical address of the GPIO module's registers. - gpio-controller: Marks the device node as a GPIO controller. - #gpio-cells : Should be two. The first cell is the pin number and the second cell is used to specify optional parameters:
Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt +1 -1
@@ -2,7 +2,7 @@ QNAP NAS devices have a microcontroller controlling the main power supply. This microcontroller is connected to UART1 of the Kirkwood and -Orion5x SoCs. Sending the charactor 'A', at 19200 baud, tells the +Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the microcontroller to turn the power off. This driver adds a handler to pm_power_off which is called to turn the power off.
Documentation/devicetree/bindings/regulator/max8997-regulator.txt +1 -1
@@ -28,7 +28,7 @@ Required properties: safe operating voltage). If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional - property is specified, then all the eigth voltage values for the + property is specified, then all the eight voltage values for the 'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified. Optional properties:
Documentation/devicetree/bindings/usb/samsung-usbphy.txt +1 -1
@@ -4,7 +4,7 @@ The Samsung's phy transceiver is used for controlling usb phy for s3c-hsotg as well as ehci-s5p and ohci-exynos usb controllers across Samsung SOCs. TODO: Adding the PHY binding with controller(s) according to the under -developement generic PHY driver. +development generic PHY driver. Required properties:
Signature · 1 line
1.8.2.451.gbfd70c5