Skip to contentSkip to conversation

regulator: tps80031: Fix LDO2 track mode for TPS80031 or TPS80032-ES1.0

PATCH Applied Axel Lin 2 participants 4 messages Apr 17, 2013 – Apr 23, 2013 Voltage and current regulator framework

lore
Share & tools
lore

Axel Lin

author
#0 lore raw

PATCH 1/2 regulator: tps80031: Fix LDO2 track mode for TPS80031 or TPS80032-ES1.0

Currently we have a special code in tps80031_ldo_set_voltage_sel() to handle LDO2 track mode for TPS80031 or TPS80032-ES1.0. The purpose is to address below issues:

Issue description:
- LDO2 traking mode is enabled
- LDO2 tracks SMPS2 voltage.
- LDO2 automatically switch-off when LDO2_CFG_VOLTAGE is changed to some discrete values (non exhaustive list):

            00011001, 00011010, 00011011, 00011100, .
- LDO2 switch-on again when LDO2_CFG_VOLTAGE is changed to other values (non exhaustive list):
        00011000, 00010111, .

LDOs have reserved codes. For these codes, LDO is switch-off.

In tracking, LDO2 ref comes from SMPS2.
However LDO2 enable is still gated by LDO2 VSEL decoding.
As a result, in tracking mode LDO2 will be disabled for following code (SMPS VSEL format):
000000 & 100000 (MSB not decoded)
011001 & 111001 (MSB not decoded)
011010 & 111010 (MSB not decoded)
011100 & 111100 (MSB not decoded)
011101 & 111101 (MSB not decoded)
011110 & 111110 (MSB not decoded)

However, current code has below bugs:
1. It uses regulator_list_voltage_linear, so list_voltage() still shows above invalid selectors have supported voltage.
2. Current code may return -EINVAL in tps80031_ldo_set_voltage_sel() for supported voltage. This is because when we use regulator_list_voltage_linear as list_voltage callback, regulator core will default use regulator_map_voltage_linear(). regulator_map_voltage_linear() has an assumption that the voltages are linear which is not true for this case.

For example,
when request voltage range is: min_uV=950000 uV && max_uV=1200000 uV regulator_map_voltage_linear() returns the selector is 29 (0x1D), set_voltage_sel() returns -EINVAL.
(The selector is in invalid range, 0x19 ~ 0x1f).

In above case, map_voltage() should find the lowest valid voltage within specific range (selector = 0x20) and set_voltage_sel() should successfully set the voltage to 987500 uV.

This patch fixes these issues by:
1. Add checking valid setting for LDO2 track mode of TPS80031 or TPS80032-ES1.0 in list_voltage. So it returns -EINVAL for invalid selectors.
2. Implement tps80031_ldo_map_voltage, use regulator_map_voltage_iterate() to find the lowest voltage within specific range for TPS80031 or TPS80032-ES1.0. This is required when the voltage map is no longer linear.

---
Hi Laxman,
I don't have this hardware, can you test this patch serial?

Thank you,
Axel

 drivers/regulator/tps80031-regulator.c |   38 ++++++++++++++++++++++++++++----
 1 file changed, 34 insertions(+), 4 deletions(-)
drivers/regulator/tps80031-regulator.c +34 -4
index 9019d0e..6430789 100644
@@ -238,12 +238,11 @@ static int tps80031_dcdc_get_voltage_sel(struct regulator_dev *rdev)
 	return vsel & SMPS_VSEL_MASK;
 }
 
-static int tps80031_ldo_set_voltage_sel(struct regulator_dev *rdev,
-		unsigned sel)
+static int tps80031_ldo_list_voltage(struct regulator_dev *rdev,
+				     unsigned int sel)
 {
 	struct tps80031_regulator *ri = rdev_get_drvdata(rdev);
 	struct device *parent = to_tps80031_dev(rdev);
-	int ret;
 
 	/* Check for valid setting for TPS80031 or TPS80032-ES1.0 */
 	if ((ri->rinfo->desc.id == TPS80031_REGULATOR_LDO2) &&
@@ -260,6 +259,36 @@ static int tps80031_ldo_set_voltage_sel(struct regulator_dev *rdev,
 		}
 	}
 
+	return regulator_list_voltage_linear(rdev, sel);
+}
+
+static int tps80031_ldo_map_voltage(struct regulator_dev *rdev,
+				    int min_uV, int max_uV)
+{
+	struct tps80031_regulator *ri = rdev_get_drvdata(rdev);
+	struct device *parent = to_tps80031_dev(rdev);
+
+	/* Check for valid setting for TPS80031 or TPS80032-ES1.0 */
+	if ((ri->rinfo->desc.id == TPS80031_REGULATOR_LDO2) &&
+			(ri->device_flags & TRACK_MODE_ENABLE)) {
+		if (((tps80031_get_chip_info(parent) == TPS80031) ||
+			((tps80031_get_chip_info(parent) == TPS80032) &&
+			(tps80031_get_pmu_version(parent) == 0x0)))) {
+			return regulator_map_voltage_iterate(rdev, min_uV,
+							     max_uV);
+		}
+	}
+
+	return regulator_map_voltage_linear(rdev, min_uV, max_uV);
+}
+
+static int tps80031_ldo_set_voltage_sel(struct regulator_dev *rdev,
+		unsigned sel)
+{
+	struct tps80031_regulator *ri = rdev_get_drvdata(rdev);
+	struct device *parent = to_tps80031_dev(rdev);
+	int ret;
+
 	ret = tps80031_write(parent, ri->rinfo->volt_id,
 			ri->rinfo->volt_reg, sel);
 	if (ret < 0)
@@ -390,7 +419,8 @@ static struct regulator_ops tps80031_dcdc_ops = {
 };
 
 static struct regulator_ops tps80031_ldo_ops = {
-	.list_voltage		= regulator_list_voltage_linear,
+	.list_voltage		= tps80031_ldo_list_voltage,
+	.map_voltage		= tps80031_ldo_map_voltage,
 	.set_voltage_sel	= tps80031_ldo_set_voltage_sel,
 	.get_voltage_sel	= tps80031_ldo_get_voltage_sel,
 	.enable			= tps80031_reg_enable,
Signature · 1 line
1.7.10.4
author
#1 lore raw

PATCH 2/2 regulator: tps80031: Convert tps80031_dcdc_ops to [get|set]_voltage_sel_regmap

---
 drivers/regulator/tps80031-regulator.c |   39 +++++---------------------------
 1 file changed, 6 insertions(+), 33 deletions(-)
drivers/regulator/tps80031-regulator.c +6 -33
index 6430789..6511d0b 100644
@@ -282,37 +282,6 @@ static int tps80031_ldo_map_voltage(struct regulator_dev *rdev,
 	return regulator_map_voltage_linear(rdev, min_uV, max_uV);
 }
 
-static int tps80031_ldo_set_voltage_sel(struct regulator_dev *rdev,
-		unsigned sel)
-{
-	struct tps80031_regulator *ri = rdev_get_drvdata(rdev);
-	struct device *parent = to_tps80031_dev(rdev);
-	int ret;
-
-	ret = tps80031_write(parent, ri->rinfo->volt_id,
-			ri->rinfo->volt_reg, sel);
-	if (ret < 0)
-		dev_err(ri->dev, "Error in writing reg 0x%02x, e = %d\n",
-			ri->rinfo->volt_reg, ret);
-	return ret;
-}
-
-static int tps80031_ldo_get_voltage_sel(struct regulator_dev *rdev)
-{
-	struct tps80031_regulator *ri = rdev_get_drvdata(rdev);
-	struct device *parent = to_tps80031_dev(rdev);
-	uint8_t vsel;
-	int ret;
-
-	ret = tps80031_read(parent, ri->rinfo->volt_id,
-				ri->rinfo->volt_reg, &vsel);
-	if (ret < 0) {
-		dev_err(ri->dev, "Error in writing the Voltage register\n");
-		return ret;
-	}
-	return vsel & rdev->desc->vsel_mask;
-}
-
 static int tps80031_vbus_is_enabled(struct regulator_dev *rdev)
 {
 	struct tps80031_regulator *ri = rdev_get_drvdata(rdev);
@@ -421,8 +390,8 @@ static struct regulator_ops tps80031_dcdc_ops = {
 static struct regulator_ops tps80031_ldo_ops = {
 	.list_voltage		= tps80031_ldo_list_voltage,
 	.map_voltage		= tps80031_ldo_map_voltage,
-	.set_voltage_sel	= tps80031_ldo_set_voltage_sel,
-	.get_voltage_sel	= tps80031_ldo_get_voltage_sel,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
 	.enable			= tps80031_reg_enable,
 	.disable		= tps80031_reg_disable,
 	.is_enabled		= tps80031_reg_is_enabled,
@@ -489,6 +458,7 @@ static struct regulator_ops tps80031_ext_reg_ops = {
 		.uV_step = 100000,				\
 		.linear_min_sel = 1,				\
 		.n_voltages = 25,				\
+		.vsel_reg = TPS80031_##_id##_CFG_VOLTAGE,	\
 		.vsel_mask = LDO_VSEL_MASK,			\
 		.enable_time = 500,				\
 	},							\
@@ -710,6 +680,7 @@ static int tps80031_regulator_probe(struct platform_device *pdev)
 	struct tps80031_regulator *pmic;
 	struct regulator_dev *rdev;
 	struct regulator_config config = { };
+	struct tps80031 *tps80031_mfd = dev_get_drvdata(pdev->dev.parent);
 	int ret;
 	int num;
 
@@ -737,6 +708,8 @@ static int tps80031_regulator_probe(struct platform_device *pdev)
 		config.dev = &pdev->dev;
 		config.init_data = NULL;
 		config.driver_data = ri;
+		config.regmap = tps80031_mfd->regmap[ri->rinfo->volt_id];
+
 		if (tps_pdata) {
 			config.init_data = tps_pdata->reg_init_data;
 			ri->config_flags = tps_pdata->config_flags;
Signature · 1 line
1.7.10.4
maintainer Applied
#3 lore raw
In reply to Axel Lin
Quoted 3 lines · Axel Lin

Currently we have a special code in tps80031_ldo_set_voltage_sel() to handle LDO2 track mode for TPS80031 or TPS80032-ES1.0. The purpose is to address below issues:

Applied, thanks.