two providers.
Hello, people.
I read iptables tutorial and lartc, but i'm still confused with one trouble.
May be this question was discussed already, so forward me solution, if is.
So, there's a trouble.
I have debian etch linux. 2.6.18-4 kernel.
On this computer i have three interfaces: eth0 - my lan, eth1, eth2 - providers.
By default all internet traffic routed through eth2. But i NEED to route mail and icq (tcp110, tcp25, tcp5190) through eth1. How can i do that?
Regards, Vitaliy Tskhovrebov.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Quoted 11 lines
So, there's a trouble.
I have debian etch linux. 2.6.18-4 kernel.
On this computer i have three interfaces: eth0 - my lan, eth1, eth2 - providers.
By default all internet traffic routed through eth2. But i NEED to route mail and icq (tcp110, tcp25, tcp5190) through eth1. How can i do that?
A while ago ive used a similar configuration, what ive done was:
- create additionall routing table
add all regular entries to it with changed default gateway for the second provider like:
ip route add xxx.xxx.xxx.xxx via yyy.yyy.yyy.yyy table 2
...
ip route add default via IP_OF_2ND_GATEWAY table 2
- mark desired traffic with iptables
iptables -I FORWARD -s LAN_NET/MASK -p tcp --dport XXX -j MARK --set-mark 2
- use ip rules to direct marked packets via alternative routing table
ip rule add fwmark 2 table 2
- and maby add additionall rule to make all packages originating at eth1 ip to go via table 2
ip rule add from ETH1_IP table 2
should be more or less something like this, though i dont recall if syntax was exactly like ive wrote above. big dissadvantage of this solution is utilisation of marks, that might be used for another purpose.
Signature · 6 lines
Radek 'Goblin' Pieczonka _______________________________________________ LARTC mailing list [email protected] http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Quoted 11 lines · Виталий Цховребов
Hello, people.
I read iptables tutorial and lartc, but i'm still confused with one trouble.
May be this question was discussed already, so forward me solution, if is.
So, there's a trouble.
Quoted 8 lines
I have debian etch linux. 2.6.18-4 kernel.
On this computer i have three interfaces: eth0 - my lan, eth1, eth2 - providers.
By default all internet traffic routed through eth2. But i NEED to route mail and icq (tcp110, tcp25, tcp5190) through eth1. How can i do that?
That is policy routing.
Is it a SNATed firewall? I use below script for a SNATed firewall where I have two links such as a Leasedline and a ADSL. I route web traffic (both HTTP and HTTPS -- port tcp 80 and tcp 443) via ADSL link.
YOU want to route mail and icq (tcp110, tcp25, tcp5190) through eth1. pls change your ports accordinly.
Pls replace gatewayipofprovider1, gatewayipofprovider2, ipofETH1 and ipofETH2 with yours.
by default, My firewall also routes trafic via eth2 (i.e- gatewayipofprovider1---
Leasedline or realiplink ) I route http and https traffic via eth1 (i.e- gatewayipofprovider2
--ADSL or adsllink ) .
in your case, it is the SAME.
below is the Script.
echo 210 realiplink >> /etc/iproute2/rt_tables
echo 211 adsllink >> /etc/iproute2/rt_tables
ip route add <http://203.115.26.65/>gatewayipofprovider1 dev eth2 table realiplink
ip route add default via gatewayipofprovider1 dev eth2 table realiplink
ip route add gatewayipofprovider2 dev eth1 table adsllink ip route add default via gatewayipofprovider2 dev eth1 table adsllink
iptables -t mangle -A OUTPUT -p tcp -m multiport --dports 80,443 -j MARK --set-mark 1
ip rule add fwmark 1 pri 100 table adsllink
iptables -t nat -A POSTROUTING -o eth1 -j SNAT --to-source ipofETH1
echo 0 > /proc/sys/net/ipv4/conf/eth1/rp_filter
ip rule add from ipofETH2 pri 200 table realiplink ip rule add from ipofETH1 pri 300 table adsllink
Then, issue below command to see routing tables
ip rule list
PLS NOTE:
In the above script, I have marked OUTPUT trafic as 1. below is the command I have given
iptables -t mangle -A OUTPUT -p tcp -m multiport --dports 80,443 -j MARK --set-mark 1
the reason for that is the firewall is itself is a SQUID proxy server. But not a TRANSPARENT PROXY.
Just acts as a normal proxy. (i.e- I have configured client browsers with ip address and port 3128.)
Try with the above script and see if it works. UNLESS it works, pls replace
the above command with this.
iptables -t mangle -A PREROUTING -p tcp -m multiport --dports 80,443 -j MARK --set-mark 1
or
iptables -t mangle -A PREROUTING -i eth0 -p tcp -m multiport --dports 80,443 -j MARK --set-mark 1
try this nad be HAPPY
_______________________________________________
Quoted 4 lines
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Signature · 2 lines
Thank you Indunil Jayasooriya
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
One solution would be to mark outbound packets using iptables and then route them based on the marks.
Quoted 12 lines
Hello, people.
I read iptables tutorial and lartc, but i'm still confused with one trouble.
May be this question was discussed already, so forward me solution, if is.
So, there's a trouble.
I have debian etch linux. 2.6.18-4 kernel.
Quoted 9 lines
On this computer i have three interfaces: eth0 - my lan, eth1, eth2 - providers.
By default all internet traffic routed through eth2. But i NEED to route mail and icq (tcp110, tcp25, tcp5190) through eth1. How can i do that?
Regards, Vitaliy Tskhovrebov.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Thanks all who help me, i'll try solutions soon, and i'll write to the list.
Signature · 7 lines
С уважением, Виталий mailto:[email protected] _______________________________________________ LARTC mailing list [email protected] http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc