usb: host: Faraday fotg210-hcd driver
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi,
Quoted 7 lines · Yuan-Hsin Chen
FOTG210 is an OTG controller which can be configured as an USB2.0 host. FOTG210 host is an ehci-like controller with some differences. First, register layout of FOTG210 is incompatible with EHCI. Furthermore, FOTG210 is lack of siTDs which means iTDs are used for both HS and FS ISO transfer.
Are there any advice?
Thanks.
Quoted 6,783 lines
Signed-off-by Yuan-Hsin Chen <[email protected]>--- drivers/usb/Makefile | 1 + drivers/usb/host/Kconfig | 12 + drivers/usb/host/Makefile | 1 + drivers/usb/host/fotg210-hcd.c | 5967 ++++++++++++++++++++++++++++++++++++++++ drivers/usb/host/fotg210.h | 746 +++++ 5 files changed, 6727 insertions(+), 0 deletions(-) create mode 100644 drivers/usb/host/fotg210-hcd.c create mode 100644 drivers/usb/host/fotg210.hdrivers/usb/Makefile +1
-0@@ -25,6 +25,7 @@ obj-$(CONFIG_USB_HWA_HCD) += host/ obj-$(CONFIG_USB_ISP1760_HCD) += host/ obj-$(CONFIG_USB_IMX21_HCD) += host/ obj-$(CONFIG_USB_FSL_MPH_DR_OF) += host/ +obj-$(CONFIG_USB_FOTG210_HCD) += host/ obj-$(CONFIG_USB_C67X00_HCD) += c67x00/drivers/usb/host/Kconfig +12
-0@@ -345,6 +345,18 @@ config USB_ISP1362_HCD To compile this driver as a module, choose M here: the module will be called isp1362-hcd. +config USB_FOTG210_HCD + tristate "FOTG210 HCD support" + depends on USB + default N + ---help--- + Faraday FOTG210 is an OTG controller which can be configured as + an USB2.0 host. It is designed to meet USB2.0 EHCI specification + with minor modification. + + To compile this driver as a module, choose M here: the + module will be called fotg210-hcd. + config USB_OHCI_HCD tristate "OHCI HCD support" depends on USB_ARCH_HAS_OHCIdrivers/usb/host/Makefile +1
-0@@ -52,3 +52,4 @@ obj-$(CONFIG_USB_FSL_MPH_DR_OF) += fsl-mph-dr-of.o obj-$(CONFIG_USB_OCTEON2_COMMON) += octeon2-common.o obj-$(CONFIG_USB_HCD_BCMA) += bcma-hcd.o obj-$(CONFIG_USB_HCD_SSB) += ssb-hcd.o +obj-$(CONFIG_USB_FOTG210_HCD) += fotg210-hcd.odrivers/usb/host/fotg210-hcd.c new file +5967
-0@@ -0,0 +1,5967 @@ +/* +* Faraday FOTG210 EHCI-like driver +* +* Copyright (c) 2013 Faraday Technology Corporation +* +* Author: Yuan-Hsin Chen <[email protected]> +* Feng-Hsin Chiang <[email protected]> +* Po-Yu Chuang <[email protected]> +* +* Most of code borrowed from the Linux-3.7 EHCI driver +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +* This program is distributed in the hope that it will be useful, but +* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY +* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License +* for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software Foundation, +* Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ +#include <linux/module.h> +#include <linux/device.h> +#include <linux/dmapool.h> +#include <linux/kernel.h> +#include <linux/delay.h> +#include <linux/ioport.h> +#include <linux/sched.h> +#include <linux/vmalloc.h> +#include <linux/errno.h> +#include <linux/init.h> +#include <linux/hrtimer.h> +#include <linux/list.h> +#include <linux/interrupt.h> +#include <linux/usb.h> +#include <linux/usb/hcd.h> +#include <linux/moduleparam.h> +#include <linux/dma-mapping.h> +#include <linux/debugfs.h> +#include <linux/slab.h> +#include <linux/uaccess.h> +#include <linux/platform_device.h> + +#include <asm/byteorder.h> +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/unaligned.h> + +/*-------------------------------------------------------------------------*/ +#define DRIVER_AUTHOR "Yuan-Hsin Chen" +#define DRIVER_DESC "FOTG210 Host Controller (EHCI) Driver" + +static const char hcd_name [] ="fotg210_hcd" ; + +#undef VERBOSE_DEBUG +#undef FOTG210_URB_TRACE + +#ifdef DEBUG +#define FOTG210_STATS +#endif + +/* magic numbers that can affect system performance */ +#define FOTG210_TUNE_CERR 3/* 0-3 qtd retries; 0 == don't stop */ +#define FOTG210_TUNE_RL_HS 4/* nak throttle; see 4.9 */ +#define FOTG210_TUNE_RL_TT 0 +#define FOTG210_TUNE_MULT_HS 1/* 1-3 transactions/uframe; 4.10.3 */ +#define FOTG210_TUNE_MULT_TT 1 +/* +* Some drivers think it's safe to schedule isochronous transfers more than +* 256 ms into the future (partly as a result of an old bug in the scheduling +* code). In an attempt to avoid trouble, we will use a minimum scheduling +* length of 512 frames instead of 256. +*/ +#define FOTG210_TUNE_FLS 1/* (medium) 512-frame schedule */ + +/* Initial IRQ latency: faster than hw default */ +static int log2_irq_thresh =0 ;// 0 to 6 +module_param (log2_irq_thresh, int,S_IRUGO ); +MODULE_PARM_DESC (log2_irq_thresh,"log2 IRQ latency, 1-64 microframes" ); + +/* initial park setting: slower than hw default */ +static unsigned park =0 ; +module_param (park, uint,S_IRUGO ); +MODULE_PARM_DESC (park,"park setting; 1-3 back-to-back async packets" ); + +/* for link power management(LPM) feature */ +static unsigned int hird; +module_param (hird, int,S_IRUGO ); +MODULE_PARM_DESC (hird,"host initiated resume duration, +1 for each 75us" ); + +#define INTR_MASK (STS_IAA | STS_FATAL | STS_PCD | STS_ERR | STS_INT) + +#include "fotg210.h" + +/*-------------------------------------------------------------------------*/ + +#define fotg210_dbg(fotg210, fmt, args...) \ + dev_dbg (fotg210_to_hcd(fotg210)->self.controller , fmt , ## args ) +#define fotg210_err(fotg210, fmt, args...) \ + dev_err (fotg210_to_hcd(fotg210)->self.controller , fmt , ## args ) +#define fotg210_info(fotg210, fmt, args...) \ + dev_info (fotg210_to_hcd(fotg210)->self.controller , fmt , ## args ) +#define fotg210_warn(fotg210, fmt, args...) \ + dev_warn (fotg210_to_hcd(fotg210)->self.controller , fmt , ## args ) + +#ifdef VERBOSE_DEBUG +# define fotg210_vdbg fotg210_dbg +#else +static inline void fotg210_vdbg (struct fotg210_hcd *fotg210, ...) {} +#endif + +#ifdef DEBUG + +/* check the values in the HCSPARAMS register +* (host controller _Structural_ parameters) +* see EHCI spec, Table 2-4 for each value +*/ +static void dbg_hcs_params (struct fotg210_hcd *fotg210,char *label) +{ +u32 params =fotg210_readl (fotg210, &fotg210->caps->hcs_params); + +fotg210_dbg (fotg210, +"%s hcs_params 0x%x ports=%d\n" , + label, params, +HCS_N_PORTS (params) + ); +} +#else + +static inline void dbg_hcs_params (struct fotg210_hcd *fotg210,char *label) {} + +#endif + +#ifdef DEBUG + +/* check the values in the HCCPARAMS register +* (host controller _Capability_ parameters) +* see EHCI Spec, Table 2-5 for each value +* */ +static void dbg_hcc_params (struct fotg210_hcd *fotg210,char *label) +{ +u32 params =fotg210_readl (fotg210, &fotg210->caps->hcc_params); + +fotg210_dbg (fotg210, +"%s hcc_params %04x uframes %s%s\n" , + label, + params, +HCC_PGM_FRAMELISTLEN (params) ?"256/512/1024" :"1024" , +HCC_CANPARK (params) ?" park" :"" ); +} +#else + +static inline void dbg_hcc_params (struct fotg210_hcd *fotg210,char *label) {} + +#endif + +#ifdef DEBUG + +static void __maybe_unused +dbg_qtd (const char *label,struct fotg210_hcd *fotg210,struct fotg210_qtd *qtd) +{ +fotg210_dbg (fotg210,"%s td %p n%08x %08x t%08x p0=%08x\n" , label, qtd, +hc32_to_cpup (fotg210, &qtd->hw_next), +hc32_to_cpup (fotg210, &qtd->hw_alt_next), +hc32_to_cpup (fotg210, &qtd->hw_token), +hc32_to_cpup (fotg210, &qtd->hw_buf [0 ])); +if (qtd->hw_buf [1 ]) +fotg210_dbg (fotg210," p1=%08x p2=%08x p3=%08x p4=%08x\n" , +hc32_to_cpup (fotg210, &qtd->hw_buf[1 ]), +hc32_to_cpup (fotg210, &qtd->hw_buf[2 ]), +hc32_to_cpup (fotg210, &qtd->hw_buf[3 ]), +hc32_to_cpup (fotg210, &qtd->hw_buf[4 ])); +} + +static void __maybe_unused +dbg_qh (const char *label,struct fotg210_hcd *fotg210,struct fotg210_qh *qh) +{ +struct fotg210_qh_hw *hw = qh->hw; + +fotg210_dbg (fotg210,"%s qh %p n%08x info %x %x qtd %x\n" , label, + qh, hw->hw_next, hw->hw_info1, hw->hw_info2, hw->hw_current); +dbg_qtd ("overlay" , fotg210, (struct fotg210_qtd *) &hw->hw_qtd_next); +} + +static void __maybe_unused +dbg_itd (const char *label,struct fotg210_hcd *fotg210,struct fotg210_itd *itd) +{ +fotg210_dbg (fotg210,"%s [%d] itd %p, next %08x, urb %p\n" , + label, itd->frame, itd,hc32_to_cpu (fotg210, itd->hw_next), + itd->urb); +fotg210_dbg (fotg210, +" trans: %08x %08x %08x %08x %08x %08x %08x %08x\n" , +hc32_to_cpu (fotg210, itd->hw_transaction[0 ]), +hc32_to_cpu (fotg210, itd->hw_transaction[1 ]), +hc32_to_cpu (fotg210, itd->hw_transaction[2 ]), +hc32_to_cpu (fotg210, itd->hw_transaction[3 ]), +hc32_to_cpu (fotg210, itd->hw_transaction[4 ]), +hc32_to_cpu (fotg210, itd->hw_transaction[5 ]), +hc32_to_cpu (fotg210, itd->hw_transaction[6 ]), +hc32_to_cpu (fotg210, itd->hw_transaction[7 ])); +fotg210_dbg (fotg210, +" buf: %08x %08x %08x %08x %08x %08x %08x\n" , +hc32_to_cpu (fotg210, itd->hw_bufp[0 ]), +hc32_to_cpu (fotg210, itd->hw_bufp[1 ]), +hc32_to_cpu (fotg210, itd->hw_bufp[2 ]), +hc32_to_cpu (fotg210, itd->hw_bufp[3 ]), +hc32_to_cpu (fotg210, itd->hw_bufp[4 ]), +hc32_to_cpu (fotg210, itd->hw_bufp[5 ]), +hc32_to_cpu (fotg210, itd->hw_bufp[6 ])); +fotg210_dbg (fotg210," index: %d %d %d %d %d %d %d %d\n" , + itd->index[0 ], itd->index[1 ], itd->index[2 ], + itd->index[3 ], itd->index[4 ], itd->index[5 ], + itd->index[6 ], itd->index[7 ]); +} + +static int __maybe_unused +dbg_status_buf (char *buf,unsigned len,const char *label,u32 status) +{ +return scnprintf (buf, len, +"%s%sstatus %04x%s%s%s%s%s%s%s%s%s%s" , + label, label [0 ] ?" " :"" , status, + (status &STS_ASS ) ?" Async" :"" , + (status &STS_PSS ) ?" Periodic" :"" , + (status &STS_RECL ) ?" Recl" :"" , + (status &STS_HALT ) ?" Halt" :"" , + (status &STS_IAA ) ?" IAA" :"" , + (status &STS_FATAL ) ?" FATAL" :"" , + (status &STS_FLR ) ?" FLR" :"" , + (status &STS_PCD ) ?" PCD" :"" , + (status &STS_ERR ) ?" ERR" :"" , + (status &STS_INT ) ?" INT" :"" + ); +} + +static int __maybe_unused +dbg_intr_buf (char *buf,unsigned len,const char *label,u32 enable) +{ +return scnprintf (buf, len, +"%s%sintrenable %02x%s%s%s%s%s%s" , + label, label [0 ] ?" " :"" , enable, + (enable &STS_IAA ) ?" IAA" :"" , + (enable &STS_FATAL ) ?" FATAL" :"" , + (enable &STS_FLR ) ?" FLR" :"" , + (enable &STS_PCD ) ?" PCD" :"" , + (enable &STS_ERR ) ?" ERR" :"" , + (enable &STS_INT ) ?" INT" :"" + ); +} + +static const char *const fls_strings [] = + {"1024" ,"512" ,"256" ,"??" }; + +static int +dbg_command_buf (char *buf,unsigned len,const char *label,u32 command) +{ +return scnprintf (buf, len, +"%s%scommand %07x %s=%d ithresh=%d%s%s%s " +"period=%s%s %s" , + label, label [0 ] ?" " :"" , command, + (command &CMD_PARK ) ?" park" :"(park)" , +CMD_PARK_CNT (command), + (command >>16 ) &0x3f , + (command &CMD_IAAD ) ?" IAAD" :"" , + (command &CMD_ASE ) ?" Async" :"" , + (command &CMD_PSE ) ?" Periodic" :"" , + fls_strings [(command >>2 ) &0x3 ], + (command &CMD_RESET ) ?" Reset" :"" , + (command &CMD_RUN ) ?"RUN" :"HALT" + ); +} + +static int +dbg_port_buf (char *buf,unsigned len,const char *label,int port,u32 status) +{ +char *sig; + +/* signaling state */ +switch (status & (3 <<10 )) { +case 0 <<10 : sig ="se0" ;break ; +case 1 <<10 : sig ="k" ;break ;/* low speed */ +case 2 <<10 : sig ="j" ;break ; +default : sig ="?" ;break ; + } + +return scnprintf (buf, len, +"%s%sport:%d status %06x %d " +"sig=%s%s%s%s%s%s%s%s" , + label, label [0 ] ?" " :"" , port, status, + status>>25 ,/*device address */ + sig, + (status &PORT_RESET ) ?" RESET" :"" , + (status &PORT_SUSPEND ) ?" SUSPEND" :"" , + (status &PORT_RESUME ) ?" RESUME" :"" , + (status &PORT_PEC ) ?" PEC" :"" , + (status &PORT_PE ) ?" PE" :"" , + (status &PORT_CSC ) ?" CSC" :"" , + (status &PORT_CONNECT ) ?" CONNECT" :"" ); +} + +#else +static inline void __maybe_unused +dbg_qh (char *label,struct fotg210_hcd *fotg210,struct fotg210_qh *qh) +{} + +static inline int __maybe_unused +dbg_status_buf (char *buf,unsigned len,const char *label,u32 status) +{return 0 ; } + +static inline int __maybe_unused +dbg_command_buf (char *buf,unsigned len,const char *label,u32 command) +{return 0 ; } + +static inline int __maybe_unused +dbg_intr_buf (char *buf,unsigned len,const char *label,u32 enable) +{return 0 ; } + +static inline int __maybe_unused +dbg_port_buf (char *buf,unsigned len,const char *label,int port,u32 status) +{return 0 ; } + +#endif /* DEBUG */ + +/* functions have the "wrong" filename when they're output... */ +#define dbg_status (fotg210, label, status) { \ + char _buf [80]; \ + dbg_status_buf (_buf, sizeof _buf, label, status); \ + fotg210_dbg (fotg210, "%s\n", _buf); \ +} + +#define dbg_cmd (fotg210, label, command) { \ + char _buf [80]; \ + dbg_command_buf (_buf, sizeof _buf, label, command); \ + fotg210_dbg (fotg210, "%s\n", _buf); \ +} + +#define dbg_port (fotg210, label, port, status) { \ + char _buf [80]; \ + dbg_port_buf (_buf, sizeof _buf, label, port, status); \ + fotg210_dbg (fotg210, "%s\n", _buf); \ +} + +/*-------------------------------------------------------------------------*/ + +#ifdef STUB_DEBUG_FILES + +static inline void create_debug_files (struct fotg210_hcd *bus) { } +static inline void remove_debug_files (struct fotg210_hcd *bus) { } + +#else + +/* troubleshooting help: expose state in debugfs */ + +static int debug_async_open (struct inode *,struct file *); +static int debug_periodic_open (struct inode *,struct file *); +static int debug_registers_open (struct inode *,struct file *); +static int debug_async_open (struct inode *,struct file *); + +static ssize_t debug_output (struct file *,char __user *,size_t ,loff_t *); +static int debug_close (struct inode *,struct file *); + +static const struct file_operations debug_async_fops = { + .owner =THIS_MODULE , + .open = debug_async_open, + .read = debug_output, + .release = debug_close, + .llseek = default_llseek, +}; +static const struct file_operations debug_periodic_fops = { + .owner =THIS_MODULE , + .open = debug_periodic_open, + .read = debug_output, + .release = debug_close, + .llseek = default_llseek, +}; +static const struct file_operations debug_registers_fops = { + .owner =THIS_MODULE , + .open = debug_registers_open, + .read = debug_output, + .release = debug_close, + .llseek = default_llseek, +}; + +static struct dentry *fotg210_debug_root; + +struct debug_buffer { +ssize_t (*fill_func)(struct debug_buffer *);/* fill method */ +struct usb_bus *bus; +struct mutex mutex;/* protect filling of buffer */ +size_t count;/* number of characters filled into buffer */ +char *output_buf; +size_t alloc_size; +}; + +#define speed_char (info1) ({ char tmp; \ + switch (info1 & (3 << 12)) { \ + case QH_FULL_SPEED: tmp = 'f'; break; \ + case QH_LOW_SPEED: tmp = 'l'; break; \ + case QH_HIGH_SPEED: tmp = 'h'; break; \ + default: tmp = '?'; break; \ + }; tmp; }) + +static inline char token_mark (struct fotg210_hcd *fotg210,__hc32 token) +{ +__u32 v =hc32_to_cpu (fotg210, token); + +if (v &QTD_STS_ACTIVE ) +return '*' ; +if (v &QTD_STS_HALT ) +return '-' ; +if (!IS_SHORT_READ (v)) +return ' ' ; +/* tries to advance through hw_alt_next */ +return '/' ; +} + +static void qh_lines ( +struct fotg210_hcd *fotg210, +struct fotg210_qh *qh, +char **nextp, +unsigned *sizep +) +{ +u32 scratch; +u32 hw_curr; +struct fotg210_qtd *td; +unsigned temp; +unsigned size = *sizep; +char *next = *nextp; +char mark; +__le32 list_end =FOTG210_LIST_END (fotg210); +struct fotg210_qh_hw *hw = qh->hw; + +if (hw->hw_qtd_next == list_end)/* NEC does this */ + mark ='@' ; +else + mark =token_mark (fotg210, hw->hw_token); +if (mark =='/' ) {/* qh_alt_next controls qh advance? */ +if ((hw->hw_alt_next &QTD_MASK (fotg210)) + == fotg210->async->hw->hw_alt_next) + mark ='#' ;/* blocked */ +else if (hw->hw_alt_next == list_end) + mark ='.' ;/* use hw_qtd_next */ +/* else alt_next points to some other qtd */ + } + scratch =hc32_to_cpup (fotg210, &hw->hw_info1); + hw_curr = (mark =='*' ) ?hc32_to_cpup (fotg210, &hw->hw_current) :0 ; + temp =scnprintf (next, size, +"qh/%p dev%d %cs ep%d %08x %08x (%08x%c %s nak%d)" , + qh, scratch &0x007f , +speed_char (scratch), + (scratch >>8 ) &0x000f , + scratch,hc32_to_cpup (fotg210, &hw->hw_info2), +hc32_to_cpup (fotg210, &hw->hw_token), mark, + (cpu_to_hc32 (fotg210,QTD_TOGGLE ) & hw->hw_token) + ?"data1" :"data0" , + (hc32_to_cpup (fotg210, &hw->hw_alt_next) >>1 ) &0x0f ); + size -= temp; + next += temp; + +/* hc may be modifying the list as we read it ... */ +list_for_each_entry (td, &qh->qtd_list, qtd_list) { + scratch =hc32_to_cpup (fotg210, &td->hw_token); + mark =' ' ; +if (hw_curr == td->qtd_dma) + mark ='*' ; +else if (hw->hw_qtd_next ==cpu_to_hc32 (fotg210, td->qtd_dma)) + mark ='+' ; +else if (QTD_LENGTH (scratch)) { +if (td->hw_alt_next == fotg210->async->hw->hw_alt_next) + mark ='#' ; +else if (td->hw_alt_next != list_end) + mark ='/' ; + } + temp =snprintf (next, size, +"\n\t%p%c%s len=%d %08x urb %p" , + td, mark, ({char *tmp; +switch ((scratch>>8 )&0x03 ) { +case 0 : tmp ="out" ;break ; +case 1 : tmp ="in" ;break ; +case 2 : tmp ="setup" ;break ; +default : tmp ="?" ;break ; + } tmp;}), + (scratch >>16 ) &0x7fff , + scratch, + td->urb); +if (size < temp) + temp = size; + size -= temp; + next += temp; +if (temp == size) + goto done; + } + + temp =snprintf (next, size,"\n" ); +if (size < temp) + temp = size; + size -= temp; + next += temp; + +done: + *sizep = size; + *nextp = next; +} + +static ssize_t fill_async_buffer (struct debug_buffer *buf) +{ +struct usb_hcd *hcd; +struct fotg210_hcd *fotg210; +unsigned long flags; +unsigned temp, size; +char *next; +struct fotg210_qh *qh; + + hcd =bus_to_hcd (buf->bus); + fotg210 =hcd_to_fotg210 (hcd); + next = buf->output_buf; + size = buf->alloc_size; + + *next =0 ; + +/* dumps a snapshot of the async schedule. +* usually empty except for long-term bulk reads, or head. +* one QH per line, and TDs we know about +*/ +spin_lock_irqsave (&fotg210->lock, flags); +for (qh = fotg210->async->qh_next.qh; size >0 && qh; qh = qh->qh_next.qh) +qh_lines (fotg210, qh, &next, &size); +if (fotg210->async_unlink && size >0 ) { + temp =scnprintf (next, size,"\nunlink =\n" ); + size -= temp; + next += temp; + +for (qh = fotg210->async_unlink; size >0 && qh; + qh = qh->unlink_next) +qh_lines (fotg210, qh, &next, &size); + } +spin_unlock_irqrestore (&fotg210->lock, flags); + +return strlen (buf->output_buf); +} + +#define DBG_SCHED_LIMIT 64 +static ssize_t fill_periodic_buffer (struct debug_buffer *buf) +{ +struct usb_hcd *hcd; +struct fotg210_hcd *fotg210; +unsigned long flags; +union fotg210_shadow p, *seen; +unsigned temp, size, seen_count; +char *next; +unsigned i; +__hc32 tag; + +if (!(seen =kmalloc (DBG_SCHED_LIMIT *sizeof *seen,GFP_ATOMIC ))) +return 0 ; + seen_count =0 ; + + hcd =bus_to_hcd (buf->bus); + fotg210 =hcd_to_fotg210 (hcd); + next = buf->output_buf; + size = buf->alloc_size; + + temp =scnprintf (next, size,"size = %d\n" , fotg210->periodic_size); + size -= temp; + next += temp; + +/* dump a snapshot of the periodic schedule. +* iso changes, interrupt usually doesn't. +*/ +spin_lock_irqsave (&fotg210->lock, flags); +for (i =0 ; i < fotg210->periodic_size; i++) { + p = fotg210->pshadow [i]; +if (likely (!p.ptr)) +continue ; + tag =Q_NEXT_TYPE (fotg210, fotg210->periodic [i]); + + temp =scnprintf (next, size,"%4d: " , i); + size -= temp; + next += temp; + +do { +struct fotg210_qh_hw *hw; + +switch (hc32_to_cpu (fotg210, tag)) { +case Q_TYPE_QH : + hw = p.qh->hw; + temp =scnprintf (next, size," qh%d-%04x/%p" , + p.qh->period, +hc32_to_cpup (fotg210, + &hw->hw_info2) +/* uframe masks */ + & (QH_CMASK |QH_SMASK ), + p.qh); + size -= temp; + next += temp; +/* don't repeat what follows this qh */ +for (temp =0 ; temp < seen_count; temp++) { +if (seen [temp].ptr != p.ptr) +continue ; +if (p.qh->qh_next.ptr) { + temp =scnprintf (next, size, +" ..." ); + size -= temp; + next += temp; + } +break ; + } +/* show more info the first time around */ +if (temp == seen_count) { +u32 scratch =hc32_to_cpup (fotg210, + &hw->hw_info1); +struct fotg210_qtd *qtd; +char *type ="" ; + +/* count tds, get ep direction */ + temp =0 ; +list_for_each_entry (qtd, + &p.qh->qtd_list, + qtd_list) { + temp++; +switch (0x03 & (hc32_to_cpu ( + fotg210, + qtd->hw_token) >>8 )) { +case 0 : type ="out" ;continue ; +case 1 : type ="in" ;continue ; + } + } + + temp =scnprintf (next, size, +" (%c%d ep%d%s " +"[%d/%d] q%d p%d)" , +speed_char (scratch), + scratch &0x007f , + (scratch >>8 ) &0x000f , type, + p.qh->usecs, p.qh->c_usecs, + temp, +0x7ff & (scratch >>16 )); + +if (seen_count <DBG_SCHED_LIMIT ) + seen [seen_count++].qh = p.qh; + }else + temp =0 ; + tag =Q_NEXT_TYPE (fotg210, hw->hw_next); + p = p.qh->qh_next; +break ; +case Q_TYPE_FSTN : + temp =scnprintf (next, size, +" fstn-%8x/%p" , p.fstn->hw_prev, + p.fstn); + tag =Q_NEXT_TYPE (fotg210, p.fstn->hw_next); + p = p.fstn->fstn_next; +break ; +case Q_TYPE_ITD : + temp =scnprintf (next, size, +" itd/%p" , p.itd); + tag =Q_NEXT_TYPE (fotg210, p.itd->hw_next); + p = p.itd->itd_next; +break ; + } + size -= temp; + next += temp; + }while (p.ptr); + + temp =scnprintf (next, size,"\n" ); + size -= temp; + next += temp; + } +spin_unlock_irqrestore (&fotg210->lock, flags); +kfree (seen); + +return buf->alloc_size - size; +} +#undef DBG_SCHED_LIMIT + +static const char *rh_state_string (struct fotg210_hcd *fotg210) +{ +switch (fotg210->rh_state) { +case FOTG210_RH_HALTED : +return "halted" ; +case FOTG210_RH_SUSPENDED : +return "suspended" ; +case FOTG210_RH_RUNNING : +return "running" ; +case FOTG210_RH_STOPPING : +return "stopping" ; + } +return "?" ; +} + +static ssize_t fill_registers_buffer (struct debug_buffer *buf) +{ +struct usb_hcd *hcd; +struct fotg210_hcd *fotg210; +unsigned long flags; +unsigned temp, size, i; +char *next, scratch [80 ]; +static char fmt [] ="%*s\n" ; +static char label [] ="" ; + + hcd =bus_to_hcd (buf->bus); + fotg210 =hcd_to_fotg210 (hcd); + next = buf->output_buf; + size = buf->alloc_size; + +spin_lock_irqsave (&fotg210->lock, flags); + +if (!HCD_HW_ACCESSIBLE (hcd)) { + size =scnprintf (next, size, +"bus %s, device %s\n" +"%s\n" +"SUSPENDED (no register access)\n" , + hcd->self.controller->bus->name, +dev_name (hcd->self.controller), + hcd->product_desc); + goto done; + } + +/* Capability Registers */ + i =HC_VERSION (fotg210,fotg210_readl (fotg210, &fotg210->caps->hc_capbase)); + temp =scnprintf (next, size, +"bus %s, device %s\n" +"%s\n" +"EHCI %x.%02x, rh state %s\n" , + hcd->self.controller->bus->name, +dev_name (hcd->self.controller), + hcd->product_desc, + i >>8 , i &0x0ff ,rh_state_string (fotg210)); + size -= temp; + next += temp; + +// FIXME interpret both types of params + i =fotg210_readl (fotg210, &fotg210->caps->hcs_params); + temp =scnprintf (next, size,"structural params 0x%08x\n" , i); + size -= temp; + next += temp; + + i =fotg210_readl (fotg210, &fotg210->caps->hcc_params); + temp =scnprintf (next, size,"capability params 0x%08x\n" , i); + size -= temp; + next += temp; + +/* Operational Registers */ + temp =dbg_status_buf (scratch,sizeof scratch, label, +fotg210_readl (fotg210, &fotg210->regs->status)); + temp =scnprintf (next, size, fmt, temp, scratch); + size -= temp; + next += temp; + + temp =dbg_command_buf (scratch,sizeof scratch, label, +fotg210_readl (fotg210, &fotg210->regs->command)); + temp =scnprintf (next, size, fmt, temp, scratch); + size -= temp; + next += temp; + + temp =dbg_intr_buf (scratch,sizeof scratch, label, +fotg210_readl (fotg210, &fotg210->regs->intr_enable)); + temp =scnprintf (next, size, fmt, temp, scratch); + size -= temp; + next += temp; + + temp =scnprintf (next, size,"uframe %04x\n" , +fotg210_read_frame_index (fotg210)); + size -= temp; + next += temp; + +if (fotg210->async_unlink) { + temp =scnprintf (next, size,"async unlink qh %p\n" , + fotg210->async_unlink); + size -= temp; + next += temp; + } + +#ifdef FOTG210_STATS + temp =scnprintf (next, size, +"irq normal %ld err %ld iaa %ld (lost %ld)\n" , + fotg210->stats.normal, fotg210->stats.error, fotg210->stats.iaa, + fotg210->stats.lost_iaa); + size -= temp; + next += temp; + + temp =scnprintf (next, size,"complete %ld unlink %ld\n" , + fotg210->stats.complete, fotg210->stats.unlink); + size -= temp; + next += temp; +#endif + +done: +spin_unlock_irqrestore (&fotg210->lock, flags); + +return buf->alloc_size - size; +} + +static struct debug_buffer *alloc_buffer (struct usb_bus *bus, +ssize_t (*fill_func)(struct debug_buffer *)) +{ +struct debug_buffer *buf; + + buf =kzalloc (sizeof (struct debug_buffer ),GFP_KERNEL ); + +if (buf) { + buf->bus = bus; + buf->fill_func = fill_func; +mutex_init (&buf->mutex); + buf->alloc_size =PAGE_SIZE ; + } + +return buf; +} + +static int fill_buffer (struct debug_buffer *buf) +{ +int ret =0 ; + +if (!buf->output_buf) + buf->output_buf =vmalloc (buf->alloc_size); + +if (!buf->output_buf) { + ret = -ENOMEM ; + goto out; + } + + ret = buf->fill_func (buf); + +if (ret >=0 ) { + buf->count = ret; + ret =0 ; + } + +out: +return ret; +} + +static ssize_t debug_output (struct file *file,char __user *user_buf, +size_t len,loff_t *offset) +{ +struct debug_buffer *buf = file->private_data; +int ret =0 ; + +mutex_lock (&buf->mutex); +if (buf->count ==0 ) { + ret =fill_buffer (buf); +if (ret !=0 ) { +mutex_unlock (&buf->mutex); + goto out; + } + } +mutex_unlock (&buf->mutex); + + ret =simple_read_from_buffer (user_buf, len, offset, + buf->output_buf, buf->count); + +out: +return ret; + +} + +static int debug_close (struct inode *inode,struct file *file) +{ +struct debug_buffer *buf = file->private_data; + +if (buf) { +vfree (buf->output_buf); +kfree (buf); + } + +return 0 ; +} +static int debug_async_open (struct inode *inode,struct file *file) +{ + file->private_data =alloc_buffer (inode->i_private, fill_async_buffer); + +return file->private_data ?0 : -ENOMEM ; +} + +static int debug_periodic_open (struct inode *inode,struct file *file) +{ +struct debug_buffer *buf; + buf =alloc_buffer (inode->i_private, fill_periodic_buffer); +if (!buf) +return -ENOMEM ; + + buf->alloc_size = (sizeof (void *) ==4 ?6 :8 )*PAGE_SIZE ; + file->private_data = buf; +return 0 ; +} + +static int debug_registers_open (struct inode *inode,struct file *file) +{ + file->private_data =alloc_buffer (inode->i_private, + fill_registers_buffer); + +return file->private_data ?0 : -ENOMEM ; +} + +static inline void create_debug_files (struct fotg210_hcd *fotg210) +{ +struct usb_bus *bus = &fotg210_to_hcd (fotg210)->self; + + fotg210->debug_dir =debugfs_create_dir (bus->bus_name, fotg210_debug_root); +if (!fotg210->debug_dir) +return ; + +if (!debugfs_create_file ("async" ,S_IRUGO , fotg210->debug_dir, bus, + &debug_async_fops)) + goto file_error; + +if (!debugfs_create_file ("periodic" ,S_IRUGO , fotg210->debug_dir, bus, + &debug_periodic_fops)) + goto file_error; + +if (!debugfs_create_file ("registers" ,S_IRUGO , fotg210->debug_dir, bus, + &debug_registers_fops)) + goto file_error; + +return ; + +file_error: +debugfs_remove_recursive (fotg210->debug_dir); +} + +static inline void remove_debug_files (struct fotg210_hcd *fotg210) +{ +debugfs_remove_recursive (fotg210->debug_dir); +} + +#endif /* STUB_DEBUG_FILES */ +/*-------------------------------------------------------------------------*/ + +/* +* handshake - spin reading hc until handshake completes or fails +* @ptr: address of hc register to be read +* @mask: bits to look at in result of read +* @done: value of those bits when handshake succeeds +* @usec: timeout in microseconds +* +* Returns negative errno, or zero on success +* +* Success happens when the "mask" bits have the specified value (hardware +* handshake done). There are two failure modes: "usec" have passed (major +* hardware flakeout), or the register reads as all-ones (hardware removed). +* +* That last failure should_only happen in cases like physical cardbus eject +* before driver shutdown. But it also seems to be caused by bugs in cardbus +* bridge shutdown: shutting down the bridge before the devices using it. +*/ +static int handshake (struct fotg210_hcd *fotg210,void __iomem *ptr, +u32 mask,u32 done,int usec) +{ +u32 result; + +do { + result =fotg210_readl (fotg210, ptr); +if (result == ~(u32 )0 )/* card removed */ +return -ENODEV ; + result &= mask; +if (result == done) +return 0 ; +udelay (1 ); + usec--; + }while (usec >0 ); +return -ETIMEDOUT ; +} + +/* +* Force HC to halt state from unknown (EHCI spec section 2.3). +* Must be called with interrupts enabled and the lock not held. +*/ +static int fotg210_halt (struct fotg210_hcd *fotg210) +{ +u32 temp; + +spin_lock_irq (&fotg210->lock); + +/* disable any irqs left enabled by previous code */ +fotg210_writel (fotg210,0 , &fotg210->regs->intr_enable); + +/* +* This routine gets called during probe before fotg210->command +* has been initialized, so we can't rely on its value. +*/ + fotg210->command &= ~CMD_RUN ; + temp =fotg210_readl (fotg210, &fotg210->regs->command); + temp &= ~(CMD_RUN |CMD_IAAD ); +fotg210_writel (fotg210, temp, &fotg210->regs->command); + +spin_unlock_irq (&fotg210->lock); +synchronize_irq (fotg210_to_hcd (fotg210)->irq); + +return handshake (fotg210, &fotg210->regs->status, +STS_HALT ,STS_HALT ,16 *125 ); +} + +/* +* Reset a non-running (STS_HALT == 1) controller. +* Must be called with interrupts enabled and the lock not held. +*/ +static int fotg210_reset (struct fotg210_hcd *fotg210) +{ +int retval; +u32 command =fotg210_readl (fotg210, &fotg210->regs->command); + +/* If the EHCI debug controller is active, special care must be +* taken before and after a host controller reset */ +if (fotg210->debug && !dbgp_reset_prep (fotg210_to_hcd (fotg210))) + fotg210->debug =NULL ; + + command |=CMD_RESET ; +dbg_cmd (fotg210,"reset" , command); +fotg210_writel (fotg210, command, &fotg210->regs->command); + fotg210->rh_state =FOTG210_RH_HALTED ; + fotg210->next_statechange = jiffies; + retval =handshake (fotg210, &fotg210->regs->command, +CMD_RESET ,0 ,250 *1000 ); + +if (retval) +return retval; + +if (fotg210->debug) +dbgp_external_startup (fotg210_to_hcd (fotg210)); + + fotg210->port_c_suspend = fotg210->suspended_ports = + fotg210->resuming_ports =0 ; +return retval; +} + +/* +* Idle the controller (turn off the schedules). +* Must be called with interrupts enabled and the lock not held. +*/ +static void fotg210_quiesce (struct fotg210_hcd *fotg210) +{ +u32 temp; + +if (fotg210->rh_state !=FOTG210_RH_RUNNING ) +return ; + +/* wait for any schedule enables/disables to take effect */ + temp = (fotg210->command <<10 ) & (STS_ASS |STS_PSS ); +handshake (fotg210, &fotg210->regs->status,STS_ASS |STS_PSS , temp,16 *125 ); + +/* then disable anything that's still active */ +spin_lock_irq (&fotg210->lock); + fotg210->command &= ~(CMD_ASE |CMD_PSE ); +fotg210_writel (fotg210, fotg210->command, &fotg210->regs->command); +spin_unlock_irq (&fotg210->lock); + +/* hardware can take 16 microframes to turn off ... */ +handshake (fotg210, &fotg210->regs->status,STS_ASS |STS_PSS ,0 ,16 *125 ); +} + +/*-------------------------------------------------------------------------*/ + +static void end_unlink_async (struct fotg210_hcd *fotg210); +static void unlink_empty_async (struct fotg210_hcd *fotg210); +static void fotg210_work (struct fotg210_hcd *fotg210); +static void start_unlink_intr (struct fotg210_hcd *fotg210,struct fotg210_qh *qh); +static void end_unlink_intr (struct fotg210_hcd *fotg210,struct fotg210_qh *qh); + +/*-------------------------------------------------------------------------*/ + +/* Set a bit in the USBCMD register */ +static void fotg210_set_command_bit (struct fotg210_hcd *fotg210,u32 bit) +{ + fotg210->command |= bit; +fotg210_writel (fotg210, fotg210->command, &fotg210->regs->command); + +/* unblock posted write */ +fotg210_readl (fotg210, &fotg210->regs->command); +} + +/* Clear a bit in the USBCMD register */ +static void fotg210_clear_command_bit (struct fotg210_hcd *fotg210,u32 bit) +{ + fotg210->command &= ~bit; +fotg210_writel (fotg210, fotg210->command, &fotg210->regs->command); + +/* unblock posted write */ +fotg210_readl (fotg210, &fotg210->regs->command); +} + +/*-------------------------------------------------------------------------*/ + +/* +* EHCI timer support... Now using hrtimers. +* +* Lots of different events are triggered from fotg210->hrtimer. Whenever +* the timer routine runs, it checks each possible event; events that are +* currently enabled and whose expiration time has passed get handled. +* The set of enabled events is stored as a collection of bitflags in +* fotg210->enabled_hrtimer_events, and they are numbered in order of +* increasing delay values (ranging between 1 ms and 100 ms). +* +* Rather than implementing a sorted list or tree of all pending events, +* we keep track only of the lowest-numbered pending event, in +* fotg210->next_hrtimer_event. Whenever fotg210->hrtimer gets restarted, its +* expiration time is set to the timeout value for this event. +* +* As a result, events might not get handled right away; the actual delay +* could be anywhere up to twice the requested delay. This doesn't +* matter, because none of the events are especially time-critical. The +* ones that matter most all have a delay of 1 ms, so they will be +* handled after 2 ms at most, which is okay. In addition to this, we +* allow for an expiration range of 1 ms. +*/ + +/* +* Delay lengths for the hrtimer event types. +* Keep this list sorted by delay length, in the same order as +* the event types indexed by enum fotg210_hrtimer_event in fotg210.h. +*/ +static unsigned event_delays_ns[] = { +1 *NSEC_PER_MSEC ,/* FOTG210_HRTIMER_POLL_ASS */ +1 *NSEC_PER_MSEC ,/* FOTG210_HRTIMER_POLL_PSS */ +1 *NSEC_PER_MSEC ,/* FOTG210_HRTIMER_POLL_DEAD */ +1125 *NSEC_PER_USEC ,/* FOTG210_HRTIMER_UNLINK_INTR */ +2 *NSEC_PER_MSEC ,/* FOTG210_HRTIMER_FREE_ITDS */ +6 *NSEC_PER_MSEC ,/* FOTG210_HRTIMER_ASYNC_UNLINKS */ +10 *NSEC_PER_MSEC ,/* FOTG210_HRTIMER_IAA_WATCHDOG */ +10 *NSEC_PER_MSEC ,/* FOTG210_HRTIMER_DISABLE_PERIODIC */ +15 *NSEC_PER_MSEC ,/* FOTG210_HRTIMER_DISABLE_ASYNC */ +100 *NSEC_PER_MSEC ,/* FOTG210_HRTIMER_IO_WATCHDOG */ +}; + +/* Enable a pending hrtimer event */ +static void fotg210_enable_event (struct fotg210_hcd *fotg210,unsigned event, +bool resched) +{ +ktime_t *timeout = &fotg210->hr_timeouts[event]; + +if (resched) + *timeout =ktime_add (ktime_get (), +ktime_set (0 , event_delays_ns[event])); + fotg210->enabled_hrtimer_events |= (1 << event); + +/* Track only the lowest-numbered pending event */ +if (event < fotg210->next_hrtimer_event) { + fotg210->next_hrtimer_event = event; +hrtimer_start_range_ns (&fotg210->hrtimer, *timeout, +NSEC_PER_MSEC ,HRTIMER_MODE_ABS ); + } +} + + +/* Poll the STS_ASS status bit; see when it agrees with CMD_ASE */ +static void fotg210_poll_ASS (struct fotg210_hcd *fotg210) +{ +unsigned actual, want; + +/* Don't enable anything if the controller isn't running (e.g., died) */ +if (fotg210->rh_state !=FOTG210_RH_RUNNING ) +return ; + + want = (fotg210->command &CMD_ASE ) ?STS_ASS :0 ; + actual =fotg210_readl (fotg210, &fotg210->regs->status) &STS_ASS ; + +if (want != actual) { + +/* Poll again later, but give up after about 20 ms */ +if (fotg210->ASS_poll_count++ <20 ) { +fotg210_enable_event (fotg210,FOTG210_HRTIMER_POLL_ASS , true); +return ; + } +fotg210_dbg (fotg210,"Waited too long for the async schedule status (%x/%x), giving up\n" , + want, actual); + } + fotg210->ASS_poll_count =0 ; + +/* The status is up-to-date; restart or stop the schedule as needed */ +if (want ==0 ) {/* Stopped */ +if (fotg210->async_count >0 ) +fotg210_set_command_bit (fotg210,CMD_ASE ); + + }else {/* Running */ +if (fotg210->async_count ==0 ) { + +/* Turn off the schedule after a while */ +fotg210_enable_event (fotg210,FOTG210_HRTIMER_DISABLE_ASYNC , + true); + } + } +} + +/* Turn off the async schedule after a brief delay */ +static void fotg210_disable_ASE (struct fotg210_hcd *fotg210) +{ +fotg210_clear_command_bit (fotg210,CMD_ASE ); +} + + +/* Poll the STS_PSS status bit; see when it agrees with CMD_PSE */ +static void fotg210_poll_PSS (struct fotg210_hcd *fotg210) +{ +unsigned actual, want; + +/* Don't do anything if the controller isn't running (e.g., died) */ +if (fotg210->rh_state !=FOTG210_RH_RUNNING ) +return ; + + want = (fotg210->command &CMD_PSE ) ?STS_PSS :0 ; + actual =fotg210_readl (fotg210, &fotg210->regs->status) &STS_PSS ; + +if (want != actual) { + +/* Poll again later, but give up after about 20 ms */ +if (fotg210->PSS_poll_count++ <20 ) { +fotg210_enable_event (fotg210,FOTG210_HRTIMER_POLL_PSS , true); +return ; + } +fotg210_dbg (fotg210,"Waited too long for the periodic schedule status (%x/%x), giving up\n" , + want, actual); + } + fotg210->PSS_poll_count =0 ; + +/* The status is up-to-date; restart or stop the schedule as needed */ +if (want ==0 ) {/* Stopped */ +if (fotg210->periodic_count >0 ) +fotg210_set_command_bit (fotg210,CMD_PSE ); + + }else {/* Running */ +if (fotg210->periodic_count ==0 ) { + +/* Turn off the schedule after a while */ +fotg210_enable_event (fotg210,FOTG210_HRTIMER_DISABLE_PERIODIC , + true); + } + } +} + +/* Turn off the periodic schedule after a brief delay */ +static void fotg210_disable_PSE (struct fotg210_hcd *fotg210) +{ +fotg210_clear_command_bit (fotg210,CMD_PSE ); +} + + +/* Poll the STS_HALT status bit; see when a dead controller stops */ +static void fotg210_handle_controller_death (struct fotg210_hcd *fotg210) +{ +if (!(fotg210_readl (fotg210, &fotg210->regs->status) &STS_HALT )) { + +/* Give up after a few milliseconds */ +if (fotg210->died_poll_count++ <5 ) { +/* Try again later */ +fotg210_enable_event (fotg210,FOTG210_HRTIMER_POLL_DEAD , true); +return ; + } +fotg210_warn (fotg210,"Waited too long for the controller to stop, giving up\n" ); + } + +/* Clean up the mess */ + fotg210->rh_state =FOTG210_RH_HALTED ; +fotg210_writel (fotg210,0 , &fotg210->regs->intr_enable); +fotg210_work (fotg210); +end_unlink_async (fotg210); + +/* Not in process context, so don't try to reset the controller */ +} + + +/* Handle unlinked interrupt QHs once they are gone from the hardware */ +static void fotg210_handle_intr_unlinks (struct fotg210_hcd *fotg210) +{ +bool stopped = (fotg210->rh_state <FOTG210_RH_RUNNING ); + +/* +* Process all the QHs on the intr_unlink list that were added +* before the current unlink cycle began. The list is in +* temporal order, so stop when we reach the first entry in the +* current cycle. But if the root hub isn't running then +* process all the QHs on the list. +*/ + fotg210->intr_unlinking = true; +while (fotg210->intr_unlink) { +struct fotg210_qh *qh = fotg210->intr_unlink; + +if (!stopped && qh->unlink_cycle == fotg210->intr_unlink_cycle) +break ; + fotg210->intr_unlink = qh->unlink_next; + qh->unlink_next =NULL ; +end_unlink_intr (fotg210, qh); + } + +/* Handle remaining entries later */ +if (fotg210->intr_unlink) { +fotg210_enable_event (fotg210,FOTG210_HRTIMER_UNLINK_INTR , true); + ++fotg210->intr_unlink_cycle; + } + fotg210->intr_unlinking = false; +} + + +/* Start another free-iTDs/siTDs cycle */ +static void start_free_itds (struct fotg210_hcd *fotg210) +{ +if (!(fotg210->enabled_hrtimer_events &BIT (FOTG210_HRTIMER_FREE_ITDS ))) { + fotg210->last_itd_to_free =list_entry ( + fotg210->cached_itd_list.prev, + struct fotg210_itd, itd_list); +fotg210_enable_event (fotg210,FOTG210_HRTIMER_FREE_ITDS , true); + } +} + +/* Wait for controller to stop using old iTDs and siTDs */ +static void end_free_itds (struct fotg210_hcd *fotg210) +{ +struct fotg210_itd *itd, *n; + +if (fotg210->rh_state <FOTG210_RH_RUNNING ) { + fotg210->last_itd_to_free =NULL ; + } + +list_for_each_entry_safe (itd, n, &fotg210->cached_itd_list, itd_list) { +list_del (&itd->itd_list); +dma_pool_free (fotg210->itd_pool, itd, itd->itd_dma); +if (itd == fotg210->last_itd_to_free) +break ; + } + +if (!list_empty (&fotg210->cached_itd_list)) +start_free_itds (fotg210); +} + + +/* Handle lost (or very late) IAA interrupts */ +static void fotg210_iaa_watchdog (struct fotg210_hcd *fotg210) +{ +if (fotg210->rh_state !=FOTG210_RH_RUNNING ) +return ; + +/* +* Lost IAA irqs wedge things badly; seen first with a vt8235. +* So we need this watchdog, but must protect it against both +* (a) SMP races against real IAA firing and retriggering, and +* (b) clean HC shutdown, when IAA watchdog was pending. +*/ +if (fotg210->async_iaa) { +u32 cmd, status; + +/* If we get here, IAA is *REALLY* late. It's barely +* conceivable that the system is so busy that CMD_IAAD +* is still legitimately set, so let's be sure it's +* clear before we read STS_IAA. (The HC should clear +* CMD_IAAD when it sets STS_IAA.) +*/ + cmd =fotg210_readl (fotg210, &fotg210->regs->command); + +/* +* If IAA is set here it either legitimately triggered +* after the watchdog timer expired (_way_ late, so we'll +* still count it as lost) ... or a silicon erratum: +* - VIA seems to set IAA without triggering the IRQ; +* - IAAD potentially cleared without setting IAA. +*/ + status =fotg210_readl (fotg210, &fotg210->regs->status); +if ((status &STS_IAA ) || !(cmd &CMD_IAAD )) { +COUNT (fotg210->stats.lost_iaa); +fotg210_writel (fotg210,STS_IAA , &fotg210->regs->status); + } + +fotg210_vdbg (fotg210,"IAA watchdog: status %x cmd %x\n" , + status, cmd); +end_unlink_async (fotg210); + } +} + + +/* Enable the I/O watchdog, if appropriate */ +static void turn_on_io_watchdog (struct fotg210_hcd *fotg210) +{ +/* Not needed if the controller isn't running or it's already enabled */ +if (fotg210->rh_state !=FOTG210_RH_RUNNING || + (fotg210->enabled_hrtimer_events & +BIT (FOTG210_HRTIMER_IO_WATCHDOG ))) +return ; + +/* +* Isochronous transfers always need the watchdog. +* For other sorts we use it only if the flag is set. +*/ +if (fotg210->isoc_count >0 || (fotg210->need_io_watchdog && + fotg210->async_count + fotg210->intr_count >0 )) +fotg210_enable_event (fotg210,FOTG210_HRTIMER_IO_WATCHDOG , true); +} + + +/* +* Handler functions for the hrtimer event types. +* Keep this array in the same order as the event types indexed by +* enum fotg210_hrtimer_event in fotg210.h. +*/ +static void (*event_handlers[])(struct fotg210_hcd *) = { + fotg210_poll_ASS,/* FOTG210_HRTIMER_POLL_ASS */ + fotg210_poll_PSS,/* FOTG210_HRTIMER_POLL_PSS */ + fotg210_handle_controller_death,/* FOTG210_HRTIMER_POLL_DEAD */ + fotg210_handle_intr_unlinks,/* FOTG210_HRTIMER_UNLINK_INTR */ + end_free_itds,/* FOTG210_HRTIMER_FREE_ITDS */ + unlink_empty_async,/* FOTG210_HRTIMER_ASYNC_UNLINKS */ + fotg210_iaa_watchdog,/* FOTG210_HRTIMER_IAA_WATCHDOG */ + fotg210_disable_PSE,/* FOTG210_HRTIMER_DISABLE_PERIODIC */ + fotg210_disable_ASE,/* FOTG210_HRTIMER_DISABLE_ASYNC */ + fotg210_work,/* FOTG210_HRTIMER_IO_WATCHDOG */ +}; + +static enum hrtimer_restart fotg210_hrtimer_func (struct hrtimer *t) +{ + struct fotg210_hcd *fotg210 = container_of(t, struct fotg210_hcd, hrtimer); +ktime_t now; +unsigned long events; +unsigned long flags; +unsigned e; + +spin_lock_irqsave (&fotg210->lock, flags); + + events = fotg210->enabled_hrtimer_events; + fotg210->enabled_hrtimer_events =0 ; + fotg210->next_hrtimer_event =FOTG210_HRTIMER_NO_EVENT ; + +/* +* Check each pending event. If its time has expired, handle +* the event; otherwise re-enable it. +*/ + now =ktime_get (); +for_each_set_bit (e, &events,FOTG210_HRTIMER_NUM_EVENTS ) { +if (now.tv64 >= fotg210->hr_timeouts[e].tv64) + event_handlers[e](fotg210); +else +fotg210_enable_event (fotg210, e, false); + } + +spin_unlock_irqrestore (&fotg210->lock, flags); +return HRTIMER_NORESTART ; +} + +/*-------------------------------------------------------------------------*/ + +#define fotg210_bus_suspend NULL +#define fotg210_bus_resume NULL + +/*-------------------------------------------------------------------------*/ + +static int check_reset_complete ( +struct fotg210_hcd *fotg210, +int index, +u32 __iomem *status_reg, +int port_status +) { +if (!(port_status &PORT_CONNECT )) +return port_status; + +/* if reset finished and it's still not enabled -- handoff */ +if (!(port_status &PORT_PE )) { +/* with integrated TT, there's nobody to hand it to! */ +fotg210_dbg (fotg210, +"Failed to enable port %d on root hub TT\n" , + index+1 ); +return port_status; + }else { +fotg210_dbg (fotg210,"port %d reset complete, port enabled\n" , + index +1 ); + } + +return port_status; +} + +/*-------------------------------------------------------------------------*/ + + +/* build "status change" packet (one or two bytes) from HC registers */ + +static int +fotg210_hub_status_data (struct usb_hcd *hcd,char *buf) +{ +struct fotg210_hcd *fotg210 =hcd_to_fotg210 (hcd); +u32 temp, status; +u32 mask; +int retval =1 ; +unsigned long flags; + +/* init status to no-changes */ + buf [0 ] =0 ; + +/* Inform the core about resumes-in-progress by returning +* a non-zero value even if there are no status changes. +*/ + status = fotg210->resuming_ports; + + mask =PORT_CSC |PORT_PEC ; +// PORT_RESUME from hardware ~= PORT_STAT_C_SUSPEND + +/* no hub change reports (bit 0) for now (power, ...) */ + +/* port N changes (bit N)? */ +spin_lock_irqsave (&fotg210->lock, flags); + + temp =fotg210_readl (fotg210, &fotg210->regs->port_status); + +/* +* Return status information even for ports with OWNER set. +* Otherwise khubd wouldn't see the disconnect event when a +* high-speed device is switched over to the companion +* controller by the user. +*/ + +if ((temp & mask) !=0 ||test_bit (0 , &fotg210->port_c_suspend) + || (fotg210->reset_done[0 ] &&time_after_eq ( + jiffies, fotg210->reset_done[0 ]))) { + buf [0 ] |=1 <<1 ; + status =STS_PCD ; + } +/* FIXME autosuspend idle root hubs */ +spin_unlock_irqrestore (&fotg210->lock, flags); +return status ? retval :0 ; +} + +/*-------------------------------------------------------------------------*/ + +static void +fotg210_hub_descriptor ( +struct fotg210_hcd *fotg210, +struct usb_hub_descriptor *desc +) { +int ports =HCS_N_PORTS (fotg210->hcs_params); +u16 temp; + + desc->bDescriptorType =0x29 ; + desc->bPwrOn2PwrGood =10 ;/* fotg210 1.0, 2.3.9 says 20ms max */ + desc->bHubContrCurrent =0 ; + + desc->bNbrPorts = ports; + temp =1 + (ports /8 ); + desc->bDescLength =7 +2 * temp; + +/* two bitmaps: ports removable, and usb 1.0 legacy PortPwrCtrlMask */ +memset (&desc->u.hs.DeviceRemovable[0 ],0 , temp); +memset (&desc->u.hs.DeviceRemovable[temp],0xff , temp); + + temp =0x0008 ;/* per-port overcurrent reporting */ + temp |=0x0002 ;/* no power switching */ + desc->wHubCharacteristics =cpu_to_le16 (temp); +} + +/*-------------------------------------------------------------------------*/ + +static int fotg210_hub_control ( +struct usb_hcd *hcd, +u16 typeReq, +u16 wValue, +u16 wIndex, +char *buf, +u16 wLength +) { +struct fotg210_hcd *fotg210 =hcd_to_fotg210 (hcd); +int ports =HCS_N_PORTS (fotg210->hcs_params); +u32 __iomem *status_reg = &fotg210->regs->port_status; +u32 temp, temp1, status; +unsigned long flags; +int retval =0 ; +unsigned selector; + +/* +* FIXME: support SetPortFeatures USB_PORT_FEAT_INDICATOR. +* HCS_INDICATOR may say we can change LEDs to off/amber/green. +* (track current state ourselves) ... blink for diagnostics, +* power, "this is the one", etc. EHCI spec supports this. +*/ + +spin_lock_irqsave (&fotg210->lock, flags); +switch (typeReq) { +case ClearHubFeature: +switch (wValue) { +case C_HUB_LOCAL_POWER : +case C_HUB_OVER_CURRENT : +/* no hub-wide feature/status flags */ +break ; +default : + goto error; + } +break ; +case ClearPortFeature: +if (!wIndex || wIndex > ports) + goto error; + wIndex--; + temp =fotg210_readl (fotg210, status_reg); + temp &= ~PORT_RWC_BITS ; + +/* +* Even if OWNER is set, so the port is owned by the +* companion controller, khubd needs to be able to clear +* the port-change status bits (especially +* USB_PORT_STAT_C_CONNECTION). +*/ + +switch (wValue) { +case USB_PORT_FEAT_ENABLE : +fotg210_writel (fotg210, temp & ~PORT_PE , status_reg); +break ; +case USB_PORT_FEAT_C_ENABLE : +fotg210_writel (fotg210, temp |PORT_PEC , status_reg); +break ; +case USB_PORT_FEAT_SUSPEND : +if (temp &PORT_RESET ) + goto error; +if (!(temp &PORT_SUSPEND )) +break ; +if ((temp &PORT_PE ) ==0 ) + goto error; + +/* resume signaling for 20 msec */ +fotg210_writel (fotg210, temp |PORT_RESUME , status_reg); + fotg210->reset_done[wIndex] = jiffies + +msecs_to_jiffies (20 ); +break ; +case USB_PORT_FEAT_C_SUSPEND : +clear_bit (wIndex, &fotg210->port_c_suspend); +break ; +case USB_PORT_FEAT_C_CONNECTION : +fotg210_writel (fotg210, temp |PORT_CSC , status_reg); +break ; +case USB_PORT_FEAT_C_OVER_CURRENT : +fotg210_writel (fotg210, temp |OTGISR_OVC , &fotg210->regs->otgisr); +break ; +case USB_PORT_FEAT_C_RESET : +/* GetPortStatus clears reset */ +break ; +default : + goto error; + } +fotg210_readl (fotg210, &fotg210->regs->command);/* unblock posted write */ +break ; +case GetHubDescriptor: +fotg210_hub_descriptor (fotg210, (struct usb_hub_descriptor *) + buf); +break ; +case GetHubStatus: +/* no hub-wide feature/status flags */ +memset (buf,0 ,4 ); +//cpu_to_le32s ((u32 *) buf); +break ; +case GetPortStatus: +if (!wIndex || wIndex > ports) + goto error; + wIndex--; + status =0 ; + temp =fotg210_readl (fotg210, status_reg); + +// wPortChange bits +if (temp &PORT_CSC ) + status |=USB_PORT_STAT_C_CONNECTION <<16 ; +if (temp &PORT_PEC ) + status |=USB_PORT_STAT_C_ENABLE <<16 ; + + temp1 =fotg210_readl (fotg210, &fotg210->regs->otgisr); +if (temp1 &OTGISR_OVC ) + status |=USB_PORT_STAT_C_OVERCURRENT <<16 ; + +/* whoever resumes must GetPortStatus to complete it!! */ +if (temp &PORT_RESUME ) { + +/* Remote Wakeup received? */ +if (!fotg210->reset_done[wIndex]) { +/* resume signaling for 20 msec */ + fotg210->reset_done[wIndex] = jiffies + +msecs_to_jiffies (20 ); +/* check the port again */ +mod_timer (&fotg210_to_hcd (fotg210)->rh_timer, + fotg210->reset_done[wIndex]); + } + +/* resume completed? */ +else if (time_after_eq (jiffies, + fotg210->reset_done[wIndex])) { +clear_bit (wIndex, &fotg210->suspended_ports); +set_bit (wIndex, &fotg210->port_c_suspend); + fotg210->reset_done[wIndex] =0 ; + +/* stop resume signaling */ + temp =fotg210_readl (fotg210, status_reg); +fotg210_writel (fotg210, + temp & ~(PORT_RWC_BITS |PORT_RESUME ), + status_reg); +clear_bit (wIndex, &fotg210->resuming_ports); + retval =handshake (fotg210, status_reg, +PORT_RESUME ,0 ,2000 /* 2msec */ ); +if (retval !=0 ) { +fotg210_err (fotg210, +"port %d resume error %d\n" , + wIndex +1 , retval); + goto error; + } + temp &= ~(PORT_SUSPEND |PORT_RESUME |(3 <<10 )); + } + } + +/* whoever resets must GetPortStatus to complete it!! */ +if ((temp &PORT_RESET ) + &&time_after_eq (jiffies, + fotg210->reset_done[wIndex])) { + status |=USB_PORT_STAT_C_RESET <<16 ; + fotg210->reset_done [wIndex] =0 ; +clear_bit (wIndex, &fotg210->resuming_ports); + +/* force reset to complete */ +fotg210_writel (fotg210, temp & ~(PORT_RWC_BITS |PORT_RESET ), + status_reg); +/* REVISIT: some hardware needs 550+ usec to clear +* this bit; seems too long to spin routinely... +*/ + retval =handshake (fotg210, status_reg, +PORT_RESET ,0 ,1000 ); +if (retval !=0 ) { +fotg210_err (fotg210,"port %d reset error %d\n" , + wIndex +1 , retval); + goto error; + } + +/* see what we found out */ + temp =check_reset_complete (fotg210, wIndex, status_reg, +fotg210_readl (fotg210, status_reg)); + } + +if (!(temp & (PORT_RESUME |PORT_RESET ))) { + fotg210->reset_done[wIndex] =0 ; +clear_bit (wIndex, &fotg210->resuming_ports); + } + +/* transfer dedicated ports to the companion hc */ +if ((temp &PORT_CONNECT ) && +test_bit (wIndex, &fotg210->companion_ports)) { + temp &= ~PORT_RWC_BITS ; +fotg210_writel (fotg210, temp, status_reg); +fotg210_dbg (fotg210,"port %d --> companion\n" , wIndex +1 ); + temp =fotg210_readl (fotg210, status_reg); + } + +/* +* Even if OWNER is set, there's no harm letting khubd +* see the wPortStatus values (they should all be 0 except +* for PORT_POWER anyway). +*/ + +if (temp &PORT_CONNECT ) { + status |=USB_PORT_STAT_CONNECTION ; + status |=fotg210_port_speed (fotg210, temp); + } +if (temp &PORT_PE ) + status |=USB_PORT_STAT_ENABLE ; + +/* maybe the port was unsuspended without our knowledge */ +if (temp & (PORT_SUSPEND |PORT_RESUME )) { + status |=USB_PORT_STAT_SUSPEND ; + }else if (test_bit (wIndex, &fotg210->suspended_ports)) { +clear_bit (wIndex, &fotg210->suspended_ports); +clear_bit (wIndex, &fotg210->resuming_ports); + fotg210->reset_done[wIndex] =0 ; +if (temp &PORT_PE ) +set_bit (wIndex, &fotg210->port_c_suspend); + } + + temp1 =fotg210_readl (fotg210, &fotg210->regs->otgisr); +if (temp1 &OTGISR_OVC ) + status |=USB_PORT_STAT_OVERCURRENT ; +if (temp &PORT_RESET ) + status |=USB_PORT_STAT_RESET ; +if (test_bit (wIndex, &fotg210->port_c_suspend)) + status |=USB_PORT_STAT_C_SUSPEND <<16 ; + +#ifndef VERBOSE_DEBUG +if (status & ~0xffff )/* only if wPortChange is interesting */ +#endif +dbg_port (fotg210,"GetStatus" , wIndex +1 , temp); +put_unaligned_le32 (status, buf); +break ; +case SetHubFeature: +switch (wValue) { +case C_HUB_LOCAL_POWER : +case C_HUB_OVER_CURRENT : +/* no hub-wide feature/status flags */ +break ; +default : + goto error; + } +break ; +case SetPortFeature: + selector = wIndex >>8 ; + wIndex &=0xff ; + +if (!wIndex || wIndex > ports) + goto error; + wIndex--; + temp =fotg210_readl (fotg210, status_reg); + temp &= ~PORT_RWC_BITS ; +switch (wValue) { +case USB_PORT_FEAT_SUSPEND : +if ((temp &PORT_PE ) ==0 + || (temp &PORT_RESET ) !=0 ) + goto error; + +/* After above check the port must be connected. +* Set appropriate bit thus could put phy into low power +* mode if we have hostpc feature +*/ +fotg210_writel (fotg210, temp |PORT_SUSPEND , status_reg); +set_bit (wIndex, &fotg210->suspended_ports); +break ; +case USB_PORT_FEAT_RESET : +if (temp &PORT_RESUME ) + goto error; +/* line status bits may report this as low speed, +* which can be fine if this root hub has a +* transaction translator built in. +*/ +fotg210_vdbg (fotg210,"port %d reset\n" , wIndex +1 ); + temp |=PORT_RESET ; + temp &= ~PORT_PE ; + +/* +* caller must wait, then call GetPortStatus +* usb 2.0 spec says 50 ms resets on root +*/ + fotg210->reset_done [wIndex] = jiffies + +msecs_to_jiffies (50 ); +fotg210_writel (fotg210, temp, status_reg); +break ; + +/* For downstream facing ports (these): one hub port is put +* into test mode according to USB2 11.24.2.13, then the hub +* must be reset (which for root hub now means rmmod+modprobe, +* or else system reboot). See EHCI 2.3.9 and 4.14 for info +* about the EHCI-specific stuff. +*/ +case USB_PORT_FEAT_TEST : +if (!selector || selector >5 ) + goto error; +spin_unlock_irqrestore (&fotg210->lock, flags); +fotg210_quiesce (fotg210); +spin_lock_irqsave (&fotg210->lock, flags); + +/* Put all enabled ports into suspend */ + temp =fotg210_readl (fotg210, status_reg) & ~PORT_RWC_BITS ; +if (temp &PORT_PE ) +fotg210_writel (fotg210, temp |PORT_SUSPEND , + status_reg); + +spin_unlock_irqrestore (&fotg210->lock, flags); +fotg210_halt (fotg210); +spin_lock_irqsave (&fotg210->lock, flags); + + temp =fotg210_readl (fotg210, status_reg); + temp |= selector <<16 ; +fotg210_writel (fotg210, temp, status_reg); +break ; + +default : + goto error; + } +fotg210_readl (fotg210, &fotg210->regs->command);/* unblock posted writes */ +break ; + +default : +error: +/* "stall" on error */ + retval = -EPIPE; + } +spin_unlock_irqrestore (&fotg210->lock, flags); +return retval; +} + +static void __maybe_unused fotg210_relinquish_port (struct usb_hcd *hcd, +int portnum) +{ +return ; +} + +static int __maybe_unused fotg210_port_handed_over (struct usb_hcd *hcd, +int portnum) +{ +return 0 ; +} +/*-------------------------------------------------------------------------*/ +/* +* There's basically three types of memory: +* - data used only by the HCD ... kmalloc is fine +* - async and periodic schedules, shared by HC and HCD ... these +* need to use dma_pool or dma_alloc_coherent +* - driver buffers, read/written by HC ... single shot DMA mapped +* +* There's also "register" data (e.g. PCI or SOC), which is memory mapped. +* No memory seen by this driver is pageable. +*/ + +/*-------------------------------------------------------------------------*/ + +/* Allocate the key transfer structures from the previously allocated pool */ + +static inline void fotg210_qtd_init (struct fotg210_hcd *fotg210,struct fotg210_qtd *qtd, +dma_addr_t dma) +{ +memset (qtd,0 ,sizeof *qtd); + qtd->qtd_dma = dma; + qtd->hw_token =cpu_to_hc32 (fotg210,QTD_STS_HALT ); + qtd->hw_next =FOTG210_LIST_END (fotg210); + qtd->hw_alt_next =FOTG210_LIST_END (fotg210); +INIT_LIST_HEAD (&qtd->qtd_list); +} + +static struct fotg210_qtd *fotg210_qtd_alloc (struct fotg210_hcd *fotg210,gfp_t flags) +{ +struct fotg210_qtd *qtd; +dma_addr_t dma; + + qtd =dma_pool_alloc (fotg210->qtd_pool, flags, &dma); +if (qtd !=NULL ) { +fotg210_qtd_init (fotg210, qtd, dma); + } +return qtd; +} + +static inline void fotg210_qtd_free (struct fotg210_hcd *fotg210,struct fotg210_qtd *qtd) +{ +dma_pool_free (fotg210->qtd_pool, qtd, qtd->qtd_dma); +} + + +static void qh_destroy (struct fotg210_hcd *fotg210,struct fotg210_qh *qh) +{ +/* clean qtds first, and know this is not linked */ +if (!list_empty (&qh->qtd_list) || qh->qh_next.ptr) { +fotg210_dbg (fotg210,"unused qh not empty!\n" ); +BUG (); + } +if (qh->dummy) +fotg210_qtd_free (fotg210, qh->dummy); +dma_pool_free (fotg210->qh_pool, qh->hw, qh->qh_dma); +kfree (qh); +} + +static struct fotg210_qh *fotg210_qh_alloc (struct fotg210_hcd *fotg210,gfp_t flags) +{ +struct fotg210_qh *qh; +dma_addr_t dma; + + qh =kzalloc (sizeof *qh,GFP_ATOMIC ); +if (!qh) + goto done; + qh->hw = (struct fotg210_qh_hw *) +dma_pool_alloc (fotg210->qh_pool, flags, &dma); +if (!qh->hw) + goto fail; +memset (qh->hw,0 ,sizeof *qh->hw); + qh->qh_dma = dma; +// INIT_LIST_HEAD (&qh->qh_list); +INIT_LIST_HEAD (&qh->qtd_list); + +/* dummy td enables safe urb queuing */ + qh->dummy =fotg210_qtd_alloc (fotg210, flags); +if (qh->dummy ==NULL ) { +fotg210_dbg (fotg210,"no dummy td\n" ); + goto fail1; + } +done: +return qh; +fail1: +dma_pool_free (fotg210->qh_pool, qh->hw, qh->qh_dma); +fail: +kfree (qh); +return NULL ; +} + +/*-------------------------------------------------------------------------*/ + +/* The queue heads and transfer descriptors are managed from pools tied +* to each of the "per device" structures. +* This is the initialisation and cleanup code. +*/ + +static void fotg210_mem_cleanup (struct fotg210_hcd *fotg210) +{ +if (fotg210->async) +qh_destroy (fotg210, fotg210->async); + fotg210->async =NULL ; + +if (fotg210->dummy) +qh_destroy (fotg210, fotg210->dummy); + fotg210->dummy =NULL ; + +/* DMA consistent memory and pools */ +if (fotg210->qtd_pool) +dma_pool_destroy (fotg210->qtd_pool); + fotg210->qtd_pool =NULL ; + +if (fotg210->qh_pool) { +dma_pool_destroy (fotg210->qh_pool); + fotg210->qh_pool =NULL ; + } + +if (fotg210->itd_pool) +dma_pool_destroy (fotg210->itd_pool); + fotg210->itd_pool =NULL ; + +if (fotg210->periodic) +dma_free_coherent (fotg210_to_hcd (fotg210)->self.controller, + fotg210->periodic_size *sizeof (u32), + fotg210->periodic, fotg210->periodic_dma); + fotg210->periodic =NULL ; + +/* shadow periodic table */ +kfree (fotg210->pshadow); + fotg210->pshadow =NULL ; +} + +/* remember to add cleanup code (above) if you add anything here */ +static int fotg210_mem_init (struct fotg210_hcd *fotg210,gfp_t flags) +{ +int i; + +/* QTDs for control/bulk/intr transfers */ + fotg210->qtd_pool =dma_pool_create ("fotg210_qtd" , +fotg210_to_hcd (fotg210)->self.controller, +sizeof (struct fotg210_qtd ), +32 /* byte alignment (for hw parts) */ , +4096 /* can't cross 4K */ ); +if (!fotg210->qtd_pool) { + goto fail; + } + +/* QHs for control/bulk/intr transfers */ + fotg210->qh_pool =dma_pool_create ("fotg210_qh" , +fotg210_to_hcd (fotg210)->self.controller, +sizeof (struct fotg210_qh_hw ), +32 /* byte alignment (for hw parts) */ , +4096 /* can't cross 4K */ ); +if (!fotg210->qh_pool) { + goto fail; + } + fotg210->async =fotg210_qh_alloc (fotg210, flags); +if (!fotg210->async) { + goto fail; + } + +/* ITD for high speed ISO transfers */ + fotg210->itd_pool =dma_pool_create ("fotg210_itd" , +fotg210_to_hcd (fotg210)->self.controller, +sizeof (struct fotg210_itd ), +64 /* byte alignment (for hw parts) */ , +4096 /* can't cross 4K */ ); +if (!fotg210->itd_pool) { + goto fail; + } + +/* Hardware periodic table */ + fotg210->periodic = (__le32 *) +dma_alloc_coherent (fotg210_to_hcd (fotg210)->self.controller, + fotg210->periodic_size *sizeof (__le32), + &fotg210->periodic_dma,0 ); +if (fotg210->periodic ==NULL ) { + goto fail; + } + +for (i =0 ; i < fotg210->periodic_size; i++) + fotg210->periodic[i] =FOTG210_LIST_END (fotg210); + +/* software shadow of hardware table */ + fotg210->pshadow =kcalloc (fotg210->periodic_size,sizeof (void *), flags); +if (fotg210->pshadow !=NULL ) +return 0 ; + +fail: +fotg210_dbg (fotg210,"couldn't init memory\n" ); +fotg210_mem_cleanup (fotg210); +return -ENOMEM ; +} +/*-------------------------------------------------------------------------*/ +/* +* EHCI hardware queue manipulation ... the core. QH/QTD manipulation. +* +* Control, bulk, and interrupt traffic all use "qh" lists. They list "qtd" +* entries describing USB transactions, max 16-20kB/entry (with 4kB-aligned +* buffers needed for the larger number). We use one QH per endpoint, queue +* multiple urbs (all three types) per endpoint. URBs may need several qtds. +* +* ISO traffic uses "ISO TD" (itd) records, and (along with +* interrupts) needs careful scheduling. Performance improvements can be +* an ongoing challenge. That's in "ehci-sched.c". +* +* USB 1.1 devices are handled (a) by "companion" OHCI or UHCI root hubs, +* or otherwise through transaction translators (TTs) in USB 2.0 hubs using +* (b) special fields in qh entries or (c) split iso entries. TTs will +* buffer low/full speed data so the host collects it at high speed. +*/ + +/*-------------------------------------------------------------------------*/ + +/* fill a qtd, returning how much of the buffer we were able to queue up */ + +static int +qtd_fill (struct fotg210_hcd *fotg210,struct fotg210_qtd *qtd,dma_addr_t buf, +size_t len,int token,int maxpacket) +{ +int i, count; +u64 addr = buf; + +/* one buffer entry per 4K ... first might be short or unaligned */ + qtd->hw_buf[0 ] =cpu_to_hc32 (fotg210, (u32 )addr); + qtd->hw_buf_hi[0 ] =cpu_to_hc32 (fotg210, (u32)(addr >>32 )); + count =0x1000 - (buf &0x0fff );/* rest of that page */ +if (likely (len < count))/* ... iff needed */ + count = len; +else { + buf +=0x1000 ; + buf &= ~0x0fff ; + +/* per-qtd limit: from 16K to 20K (best alignment) */ +for (i =1 ; count < len && i <5 ; i++) { + addr = buf; + qtd->hw_buf[i] =cpu_to_hc32 (fotg210, (u32 )addr); + qtd->hw_buf_hi[i] =cpu_to_hc32 (fotg210, + (u32)(addr >>32 )); + buf +=0x1000 ; +if ((count +0x1000 ) < len) + count +=0x1000 ; +else + count = len; + } + +/* short packets may only terminate transfers */ +if (count != len) + count -= (count % maxpacket); + } + qtd->hw_token =cpu_to_hc32 (fotg210, (count <<16 ) | token); + qtd->length = count; + +return count; +} + +/*-------------------------------------------------------------------------*/ + +static inline void +qh_update (struct fotg210_hcd *fotg210,struct fotg210_qh *qh,struct fotg210_qtd *qtd) +{ +struct fotg210_qh_hw *hw = qh->hw; + +/* writes to an active overlay are unsafe */ +BUG_ON (qh->qh_state !=QH_STATE_IDLE ); + + hw->hw_qtd_next =QTD_NEXT (fotg210, qtd->qtd_dma); + hw->hw_alt_next =FOTG210_LIST_END (fotg210); + +/* Except for control endpoints, we make hardware maintain data +* toggle (like OHCI) ... here (re)initialize the toggle in the QH, +* and set the pseudo-toggle in udev. Only usb_clear_halt() will +* ever clear it. +*/ +if (!(hw->hw_info1 &cpu_to_hc32 (fotg210,QH_TOGGLE_CTL ))) { +unsigned is_out, epnum; + + is_out = qh->is_out; + epnum = (hc32_to_cpup (fotg210, &hw->hw_info1) >>8 ) &0x0f ; +if (unlikely (!usb_gettoggle (qh->dev, epnum, is_out))) { + hw->hw_token &= ~cpu_to_hc32 (fotg210,QTD_TOGGLE ); +usb_settoggle (qh->dev, epnum, is_out,1 ); + } + } + + hw->hw_token &=cpu_to_hc32 (fotg210,QTD_TOGGLE |QTD_STS_PING ); +} + +/* if it weren't for a common silicon quirk (writing the dummy into the qh +* overlay, so qh->hw_token wrongly becomes inactive/halted), only fault +* recovery (including urb dequeue) would need software changes to a QH... +*/ +static void +qh_refresh (struct fotg210_hcd *fotg210,struct fotg210_qh *qh) +{ +struct fotg210_qtd *qtd; + +if (list_empty (&qh->qtd_list)) + qtd = qh->dummy; +else { + qtd =list_entry (qh->qtd_list.next, + struct fotg210_qtd, qtd_list); +/* +* first qtd may already be partially processed. +* If we come here during unlink, the QH overlay region +* might have reference to the just unlinked qtd. The +* qtd is updated in qh_completions(). Update the QH +* overlay here. +*/ +if (cpu_to_hc32 (fotg210, qtd->qtd_dma) == qh->hw->hw_current) { + qh->hw->hw_qtd_next = qtd->hw_next; + qtd =NULL ; + } + } + +if (qtd) +qh_update (fotg210, qh, qtd); +} + +/*-------------------------------------------------------------------------*/ + +static void qh_link_async (struct fotg210_hcd *fotg210,struct fotg210_qh *qh); + +static void fotg210_clear_tt_buffer_complete (struct usb_hcd *hcd, +struct usb_host_endpoint *ep) +{ +struct fotg210_hcd *fotg210 =hcd_to_fotg210 (hcd); +struct fotg210_qh *qh = ep->hcpriv; +unsigned long flags; + +spin_lock_irqsave (&fotg210->lock, flags); + qh->clearing_tt =0 ; +if (qh->qh_state ==QH_STATE_IDLE && !list_empty (&qh->qtd_list) + && fotg210->rh_state ==FOTG210_RH_RUNNING ) +qh_link_async (fotg210, qh); +spin_unlock_irqrestore (&fotg210->lock, flags); +} + +static void fotg210_clear_tt_buffer (struct fotg210_hcd *fotg210,struct fotg210_qh *qh, +struct urb *urb,u32 token) +{ + +/* If an async split transaction gets an error or is unlinked, +* the TT buffer may be left in an indeterminate state. We +* have to clear the TT buffer. +* +* Note: this routine is never called for Isochronous transfers. +*/ +if (urb->dev->tt && !usb_pipeint (urb->pipe) && !qh->clearing_tt) { +#ifdef DEBUG +struct usb_device *tt = urb->dev->tt->hub; +dev_dbg (&tt->dev, +"clear tt buffer port %d, a%d ep%d t%08x\n" , + urb->dev->ttport, urb->dev->devnum, +usb_pipeendpoint (urb->pipe), token); +#endif /* DEBUG */ +if (urb->dev->tt->hub != +fotg210_to_hcd (fotg210)->self.root_hub) { +if (usb_hub_clear_tt_buffer (urb) ==0 ) + qh->clearing_tt =1 ; + } + } +} + +static int qtd_copy_status ( +struct fotg210_hcd *fotg210, +struct urb *urb, +size_t length, +u32 token +) +{ +int status = -EINPROGRESS ; + +/* count IN/OUT bytes, not SETUP (even short packets) */ +if (likely (QTD_PID (token) !=2 )) + urb->actual_length += length -QTD_LENGTH (token); + +/* don't modify error codes */ +if (unlikely (urb->unlinked)) +return status; + +/* force cleanup after short read; not always an error */ +if (unlikely (IS_SHORT_READ (token))) + status = -EREMOTEIO ; + +/* serious "can't proceed" faults reported by the hardware */ +if (token &QTD_STS_HALT ) { +if (token &QTD_STS_BABBLE ) { +/* FIXME "must" disable babbling device's port too */ + status = -EOVERFLOW ; +/* CERR nonzero + halt --> stall */ + }else if (QTD_CERR (token)) { + status = -EPIPE ; + +/* In theory, more than one of the following bits can be set +* since they are sticky and the transaction is retried. +* Which to test first is rather arbitrary. +*/ + }else if (token &QTD_STS_MMF ) { +/* fs/ls interrupt xfer missed the complete-split */ + status = -EPROTO ; + }else if (token &QTD_STS_DBE ) { + status = (QTD_PID (token) ==1 )/* IN ? */ + ? -ENOSR /* hc couldn't read data */ + : -ECOMM ;/* hc couldn't write data */ + }else if (token &QTD_STS_XACT ) { +/* timeout, bad CRC, wrong PID, etc */ +fotg210_dbg (fotg210,"devpath %s ep%d%s 3strikes\n" , + urb->dev->devpath, +usb_pipeendpoint (urb->pipe), +usb_pipein (urb->pipe) ?"in" :"out" ); + status = -EPROTO ; + }else {/* unknown */ + status = -EPROTO ; + } + +fotg210_vdbg (fotg210, +"dev%d ep%d%s qtd token %08x --> status %d\n" , +usb_pipedevice (urb->pipe), +usb_pipeendpoint (urb->pipe), +usb_pipein (urb->pipe) ?"in" :"out" , + token, status); + } + +return status; +} + +static void +fotg210_urb_done (struct fotg210_hcd *fotg210,struct urb *urb,int status) +__releases(fotg210->lock) +__acquires(fotg210->lock) +{ +if (likely (urb->hcpriv !=NULL )) { +struct fotg210_qh *qh = (struct fotg210_qh *) urb->hcpriv; + +/* S-mask in a QH means it's an interrupt urb */ +if ((qh->hw->hw_info2 &cpu_to_hc32 (fotg210,QH_SMASK )) !=0 ) { + +/* ... update hc-wide periodic stats (for usbfs) */ +fotg210_to_hcd (fotg210)->self.bandwidth_int_reqs--; + } + } + +if (unlikely (urb->unlinked)) { +COUNT (fotg210->stats.unlink); + }else { +/* report non-error and short read status as zero */ +if (status == -EINPROGRESS || status == -EREMOTEIO ) + status =0 ; +COUNT (fotg210->stats.complete); + } + +#ifdef FOTG210_URB_TRACE +fotg210_dbg (fotg210, +"%s %s urb %p ep%d%s status %d len %d/%d\n" , + __func__, urb->dev->devpath, urb, +usb_pipeendpoint (urb->pipe), +usb_pipein (urb->pipe) ?"in" :"out" , + status, + urb->actual_length, urb->transfer_buffer_length); +#endif + +/* complete() can reenter this HCD */ +usb_hcd_unlink_urb_from_ep (fotg210_to_hcd (fotg210), urb); +spin_unlock (&fotg210->lock); +usb_hcd_giveback_urb (fotg210_to_hcd (fotg210), urb, status); +spin_lock (&fotg210->lock); +} + +static int qh_schedule (struct fotg210_hcd *fotg210,struct fotg210_qh *qh); + +/* +* Process and free completed qtds for a qh, returning URBs to drivers. +* Chases up to qh->hw_current. Returns number of completions called, +* indicating how much "real" work we did. +*/ +static unsigned +qh_completions (struct fotg210_hcd *fotg210,struct fotg210_qh *qh) +{ +struct fotg210_qtd *last, *end = qh->dummy; +struct list_head *entry, *tmp; +int last_status; +int stopped; +unsigned count =0 ; +u8 state; +struct fotg210_qh_hw *hw = qh->hw; + +if (unlikely (list_empty (&qh->qtd_list))) +return count; + +/* completions (or tasks on other cpus) must never clobber HALT +* till we've gone through and cleaned everything up, even when +* they add urbs to this qh's queue or mark them for unlinking. +* +* NOTE: unlinking expects to be done in queue order. +* +* It's a bug for qh->qh_state to be anything other than +* QH_STATE_IDLE, unless our caller is scan_async() or +* scan_intr(). +*/ + state = qh->qh_state; + qh->qh_state =QH_STATE_COMPLETING ; + stopped = (state ==QH_STATE_IDLE ); + + rescan: + last =NULL ; + last_status = -EINPROGRESS ; + qh->needs_rescan =0 ; + +/* remove de-activated QTDs from front of queue. +* after faults (including short reads), cleanup this urb +* then let the queue advance. +* if queue is stopped, handles unlinks. +*/ + list_for_each_safe (entry, tmp, &qh->qtd_list) { +struct fotg210_qtd *qtd; +struct urb *urb; +u32 token =0 ; + + qtd = list_entry (entry, struct fotg210_qtd, qtd_list); + urb = qtd->urb; + +/* clean up any state from previous QTD ...*/ +if (last) { +if (likely (last->urb != urb)) { +fotg210_urb_done (fotg210, last->urb, last_status); + count++; + last_status = -EINPROGRESS ; + } +fotg210_qtd_free (fotg210, last); + last =NULL ; + } + +/* ignore urbs submitted during completions we reported */ +if (qtd == end) +break ; + +/* hardware copies qtd out of qh overlay */ +rmb (); + token =hc32_to_cpu (fotg210, qtd->hw_token); + +/* always clean up qtds the hc de-activated */ + retry_xacterr: +if ((token &QTD_STS_ACTIVE ) ==0 ) { + +/* Report Data Buffer Error: non-fatal but useful */ +if (token &QTD_STS_DBE ) +fotg210_dbg (fotg210, +"detected DataBufferErr for urb %p ep%d%s len %d, qtd %p [qh %p]\n" , + urb, +usb_endpoint_num (&urb->ep->desc), +usb_endpoint_dir_in (&urb->ep->desc) ?"in" :"out" , + urb->transfer_buffer_length, + qtd, + qh); + +/* on STALL, error, and short reads this urb must +* complete and all its qtds must be recycled. +*/ +if ((token &QTD_STS_HALT ) !=0 ) { + +/* retry transaction errors until we +* reach the software xacterr limit +*/ +if ((token &QTD_STS_XACT ) && +QTD_CERR (token) ==0 && + ++qh->xacterrs <QH_XACTERR_MAX && + !urb->unlinked) { +fotg210_dbg (fotg210, +"detected XactErr len %zu/%zu retry %d\n" , + qtd->length -QTD_LENGTH (token), qtd->length, qh->xacterrs); + +/* reset the token in the qtd and the +* qh overlay (which still contains +* the qtd) so that we pick up from +* where we left off +*/ + token &= ~QTD_STS_HALT ; + token |=QTD_STS_ACTIVE | + (FOTG210_TUNE_CERR <<10 ); + qtd->hw_token =cpu_to_hc32 (fotg210, + token); +wmb (); + hw->hw_token =cpu_to_hc32 (fotg210, + token); + goto retry_xacterr; + } + stopped =1 ; + +/* magic dummy for some short reads; qh won't advance. +* that silicon quirk can kick in with this dummy too. +* +* other short reads won't stop the queue, including +* control transfers (status stage handles that) or +* most other single-qtd reads ... the queue stops if +* URB_SHORT_NOT_OK was set so the driver submitting +* the urbs could clean it up. +*/ + }else if (IS_SHORT_READ (token) + && !(qtd->hw_alt_next + &FOTG210_LIST_END (fotg210))) { + stopped =1 ; + } + +/* stop scanning when we reach qtds the hc is using */ + }else if (likely (!stopped + && fotg210->rh_state >=FOTG210_RH_RUNNING )) { +break ; + +/* scan the whole queue for unlinks whenever it stops */ + }else { + stopped =1 ; + +/* cancel everything if we halt, suspend, etc */ +if (fotg210->rh_state <FOTG210_RH_RUNNING ) + last_status = -ESHUTDOWN ; + +/* this qtd is active; skip it unless a previous qtd +* for its urb faulted, or its urb was canceled. +*/ +else if (last_status == -EINPROGRESS && !urb->unlinked) +continue ; + +/* qh unlinked; token in overlay may be most current */ +if (state ==QH_STATE_IDLE + &&cpu_to_hc32 (fotg210, qtd->qtd_dma) + == hw->hw_current) { + token =hc32_to_cpu (fotg210, hw->hw_token); + +/* An unlink may leave an incomplete +* async transaction in the TT buffer. +* We have to clear it. +*/ +fotg210_clear_tt_buffer (fotg210, qh, urb, token); + } + } + +/* unless we already know the urb's status, collect qtd status +* and update count of bytes transferred. in common short read +* cases with only one data qtd (including control transfers), +* queue processing won't halt. but with two or more qtds (for +* example, with a 32 KB transfer), when the first qtd gets a +* short read the second must be removed by hand. +*/ +if (last_status == -EINPROGRESS ) { + last_status =qtd_copy_status (fotg210, urb, + qtd->length, token); +if (last_status == -EREMOTEIO + && (qtd->hw_alt_next + &FOTG210_LIST_END (fotg210))) + last_status = -EINPROGRESS ; + +/* As part of low/full-speed endpoint-halt processing +* we must clear the TT buffer (11.17.5). +*/ +if (unlikely (last_status != -EINPROGRESS && + last_status != -EREMOTEIO )) { +/* The TT's in some hubs malfunction when they +* receive this request following a STALL (they +* stop sending isochronous packets). Since a +* STALL can't leave the TT buffer in a busy +* state (if you believe Figures 11-48 - 11-51 +* in the USB 2.0 spec), we won't clear the TT +* buffer in this case. Strictly speaking this +* is a violation of the spec. +*/ +if (last_status != -EPIPE ) +fotg210_clear_tt_buffer (fotg210, qh, urb, + token); + } + } + +/* if we're removing something not at the queue head, +* patch the hardware queue pointer. +*/ +if (stopped && qtd->qtd_list.prev != &qh->qtd_list) { + last =list_entry (qtd->qtd_list.prev, + struct fotg210_qtd, qtd_list); + last->hw_next = qtd->hw_next; + } + +/* remove qtd; it's recycled after possible urb completion */ +list_del (&qtd->qtd_list); + last = qtd; + +/* reinit the xacterr counter for the next qtd */ + qh->xacterrs =0 ; + } + +/* last urb's completion might still need calling */ +if (likely (last !=NULL )) { +fotg210_urb_done (fotg210, last->urb, last_status); + count++; +fotg210_qtd_free (fotg210, last); + } + +/* Do we need to rescan for URBs dequeued during a giveback? */ +if (unlikely (qh->needs_rescan)) { +/* If the QH is already unlinked, do the rescan now. */ +if (state ==QH_STATE_IDLE ) + goto rescan; + +/* Otherwise we have to wait until the QH is fully unlinked. +* Our caller will start an unlink if qh->needs_rescan is +* set. But if an unlink has already started, nothing needs +* to be done. +*/ +if (state !=QH_STATE_LINKED ) + qh->needs_rescan =0 ; + } + +/* restore original state; caller must unlink or relink */ + qh->qh_state = state; + +/* be sure the hardware's done with the qh before refreshing +* it after fault cleanup, or recovering from silicon wrongly +* overlaying the dummy qtd (which reduces DMA chatter). +*/ +if (stopped !=0 || hw->hw_qtd_next ==FOTG210_LIST_END (fotg210)) { +switch (state) { +case QH_STATE_IDLE : +qh_refresh (fotg210, qh); +break ; +case QH_STATE_LINKED : +/* We won't refresh a QH that's linked (after the HC +* stopped the queue). That avoids a race: +* - HC reads first part of QH; +* - CPU updates that first part and the token; +* - HC reads rest of that QH, including token +* Result: HC gets an inconsistent image, and then +* DMAs to/from the wrong memory (corrupting it). +* +* That should be rare for interrupt transfers, +* except maybe high bandwidth ... +*/ + +/* Tell the caller to start an unlink */ + qh->needs_rescan =1 ; +break ; +/* otherwise, unlink already started */ + } + } + +return count; +} + +/*-------------------------------------------------------------------------*/ + +// high bandwidth multiplier, as encoded in highspeed endpoint descriptors +#define hb_mult (wMaxPacketSize) (1 + (((wMaxPacketSize) >> 11) & 0x03)) +// ... and packet size, for any kind of endpoint descriptor +#define max_packet (wMaxPacketSize) ((wMaxPacketSize) & 0x07ff) + +/* +* reverse of qh_urb_transaction: free a list of TDs. +* used for cleanup after errors, before HC sees an URB's TDs. +*/ +static void qtd_list_free ( +struct fotg210_hcd *fotg210, +struct urb *urb, +struct list_head *qtd_list +) { +struct list_head *entry, *temp; + + list_for_each_safe (entry, temp, qtd_list) { +struct fotg210_qtd *qtd; + + qtd = list_entry (entry, struct fotg210_qtd, qtd_list); +list_del (&qtd->qtd_list); +fotg210_qtd_free (fotg210, qtd); + } +} + +/* +* create a list of filled qtds for this URB; won't link into qh. +*/ +static struct list_head * +qh_urb_transaction ( +struct fotg210_hcd *fotg210, +struct urb *urb, +struct list_head *head, +gfp_t flags +) { +struct fotg210_qtd *qtd, *qtd_prev; +dma_addr_t buf; +int len, this_sg_len, maxpacket; +int is_input; +u32 token; +int i; +struct scatterlist *sg; + +/* +* URBs map to sequences of QTDs: one logical transaction +*/ + qtd =fotg210_qtd_alloc (fotg210, flags); +if (unlikely (!qtd)) +return NULL ; +list_add_tail (&qtd->qtd_list, head); + qtd->urb = urb; + + token =QTD_STS_ACTIVE ; + token |= (FOTG210_TUNE_CERR <<10 ); +/* for split transactions, SplitXState initialized to zero */ + + len = urb->transfer_buffer_length; + is_input =usb_pipein (urb->pipe); +if (usb_pipecontrol (urb->pipe)) { +/* SETUP pid */ +qtd_fill (fotg210, qtd, urb->setup_dma, +sizeof (struct usb_ctrlrequest ), + token | (2 /* "setup" */ <<8 ),8 ); + +/* ... and always at least one more pid */ + token ^=QTD_TOGGLE ; + qtd_prev = qtd; + qtd =fotg210_qtd_alloc (fotg210, flags); +if (unlikely (!qtd)) + goto cleanup; + qtd->urb = urb; + qtd_prev->hw_next =QTD_NEXT (fotg210, qtd->qtd_dma); +list_add_tail (&qtd->qtd_list, head); + +/* for zero length DATA stages, STATUS is always IN */ +if (len ==0 ) + token |= (1 /* "in" */ <<8 ); + } + +/* +* data transfer stage: buffer setup +*/ + i = urb->num_mapped_sgs; +if (len >0 && i >0 ) { + sg = urb->sg; + buf =sg_dma_address (sg); + +/* urb->transfer_buffer_length may be smaller than the +* size of the scatterlist (or vice versa) +*/ + this_sg_len =min_t (int,sg_dma_len (sg), len); + }else { + sg =NULL ; + buf = urb->transfer_dma; + this_sg_len = len; + } + +if (is_input) + token |= (1 /* "in" */ <<8 ); +/* else it's already initted to "out" pid (0 << 8) */ + + maxpacket =max_packet (usb_maxpacket (urb->dev, urb->pipe, !is_input)); + +/* +* buffer gets wrapped in one or more qtds; +* last one may be "short" (including zero len) +* and may serve as a control status ack +*/ +for (;;) { +int this_qtd_len; + + this_qtd_len =qtd_fill (fotg210, qtd, buf, this_sg_len, token, + maxpacket); + this_sg_len -= this_qtd_len; + len -= this_qtd_len; + buf += this_qtd_len; + +/* +* short reads advance to a "magic" dummy instead of the next +* qtd ... that forces the queue to stop, for manual cleanup. +* (this will usually be overridden later.) +*/ +if (is_input) + qtd->hw_alt_next = fotg210->async->hw->hw_alt_next; + +/* qh makes control packets use qtd toggle; maybe switch it */ +if ((maxpacket & (this_qtd_len + (maxpacket -1 ))) ==0 ) + token ^=QTD_TOGGLE ; + +if (likely (this_sg_len <=0 )) { +if (--i <=0 || len <=0 ) +break ; + sg =sg_next (sg); + buf =sg_dma_address (sg); + this_sg_len =min_t (int,sg_dma_len (sg), len); + } + + qtd_prev = qtd; + qtd =fotg210_qtd_alloc (fotg210, flags); +if (unlikely (!qtd)) + goto cleanup; + qtd->urb = urb; + qtd_prev->hw_next =QTD_NEXT (fotg210, qtd->qtd_dma); +list_add_tail (&qtd->qtd_list, head); + } + +/* +* unless the caller requires manual cleanup after short reads, +* have the alt_next mechanism keep the queue running after the +* last data qtd (the only one, for control and most other cases). +*/ +if (likely ((urb->transfer_flags &URB_SHORT_NOT_OK ) ==0 + ||usb_pipecontrol (urb->pipe))) + qtd->hw_alt_next =FOTG210_LIST_END (fotg210); + +/* +* control requests may need a terminating data "status" ack; +* other OUT ones may need a terminating short packet +* (zero length). +*/ +if (likely (urb->transfer_buffer_length !=0 )) { +int one_more =0 ; + +if (usb_pipecontrol (urb->pipe)) { + one_more =1 ; + token ^=0x0100 ;/* "in" <--> "out" */ + token |=QTD_TOGGLE ;/* force DATA1 */ + }else if (usb_pipeout (urb->pipe) + && (urb->transfer_flags &URB_ZERO_PACKET ) + && !(urb->transfer_buffer_length % maxpacket)) { + one_more =1 ; + } +if (one_more) { + qtd_prev = qtd; + qtd =fotg210_qtd_alloc (fotg210, flags); +if (unlikely (!qtd)) + goto cleanup; + qtd->urb = urb; + qtd_prev->hw_next =QTD_NEXT (fotg210, qtd->qtd_dma); +list_add_tail (&qtd->qtd_list, head); + +/* never any data in such packets */ +qtd_fill (fotg210, qtd,0 ,0 , token,0 ); + } + } + +/* by default, enable interrupt on urb completion */ +if (likely (!(urb->transfer_flags &URB_NO_INTERRUPT ))) + qtd->hw_token |=cpu_to_hc32 (fotg210,QTD_IOC ); +return head; + +cleanup: +qtd_list_free (fotg210, urb, head); +return NULL ; +} + +/*-------------------------------------------------------------------------*/ + +// Would be best to create all qh's from config descriptors, +// when each interface/altsetting is established. Unlink +// any previous qh and cancel its urbs first; endpoints are +// implicitly reset then (data toggle too). +// That'd mean updating how usbcore talks to HCDs. (2.7?) + + +/* +* Each QH holds a qtd list; a QH is used for everything except iso. +* +* For interrupt urbs, the scheduler must set the microframe scheduling +* mask(s) each time the QH gets scheduled. For highspeed, that's +* just one microframe in the s-mask. For split interrupt transactions +* there are additional complications: c-mask, maybe FSTNs. +*/ +static struct fotg210_qh * +qh_make ( +struct fotg210_hcd *fotg210, +struct urb *urb, +gfp_t flags +) { +struct fotg210_qh *qh =fotg210_qh_alloc (fotg210, flags); +u32 info1 =0 , info2 =0 ; +int is_input, type; +int maxp =0 ; +struct usb_tt *tt = urb->dev->tt; +struct fotg210_qh_hw *hw; + +if (!qh) +return qh; + +/* +* init endpoint/device data for this QH +*/ + info1 |=usb_pipeendpoint (urb->pipe) <<8 ; + info1 |=usb_pipedevice (urb->pipe) <<0 ; + + is_input =usb_pipein (urb->pipe); + type =usb_pipetype (urb->pipe); + maxp =usb_maxpacket (urb->dev, urb->pipe, !is_input); + +/* 1024 byte maxpacket is a hardware ceiling. High bandwidth +* acts like up to 3KB, but is built from smaller packets. +*/ +if (max_packet (maxp) >1024 ) { +fotg210_dbg (fotg210,"bogus qh maxpacket %d\n" ,max_packet (maxp)); + goto done; + } + +/* Compute interrupt scheduling parameters just once, and save. +* - allowing for high bandwidth, how many nsec/uframe are used? +* - split transactions need a second CSPLIT uframe; same question +* - splits also need a schedule gap (for full/low speed I/O) +* - qh has a polling interval +* +* For control/bulk requests, the HC or TT handles these. +*/ +if (type ==PIPE_INTERRUPT ) { + qh->usecs =NS_TO_US (usb_calc_bus_time (USB_SPEED_HIGH , + is_input,0 , +hb_mult (maxp) *max_packet (maxp))); + qh->start =NO_FRAME ; + +if (urb->dev->speed ==USB_SPEED_HIGH ) { + qh->c_usecs =0 ; + qh->gap_uf =0 ; + + qh->period = urb->interval >>3 ; +if (qh->period ==0 && urb->interval !=1 ) { +/* NOTE interval 2 or 4 uframes could work. +* But interval 1 scheduling is simpler, and +* includes high bandwidth. +*/ + urb->interval =1 ; + }else if (qh->period > fotg210->periodic_size) { + qh->period = fotg210->periodic_size; + urb->interval = qh->period <<3 ; + } + }else { +int think_time; + +/* gap is f(FS/LS transfer times) */ + qh->gap_uf =1 +usb_calc_bus_time (urb->dev->speed, + is_input,0 , maxp) / (125 *1000 ); + +/* FIXME this just approximates SPLIT/CSPLIT times */ +if (is_input) {// SPLIT, gap, CSPLIT+DATA + qh->c_usecs = qh->usecs +HS_USECS (0 ); + qh->usecs =HS_USECS (1 ); + }else {// SPLIT+DATA, gap, CSPLIT + qh->usecs +=HS_USECS (1 ); + qh->c_usecs =HS_USECS (0 ); + } + + think_time = tt ? tt->think_time :0 ; + qh->tt_usecs =NS_TO_US (think_time + +usb_calc_bus_time (urb->dev->speed, + is_input,0 ,max_packet (maxp))); + qh->period = urb->interval; +if (qh->period > fotg210->periodic_size) { + qh->period = fotg210->periodic_size; + urb->interval = qh->period; + } + } + } + +/* support for tt scheduling, and access to toggles */ + qh->dev = urb->dev; + +/* using TT? */ +switch (urb->dev->speed) { +case USB_SPEED_LOW : + info1 |=QH_LOW_SPEED ; +/* FALL THROUGH */ + +case USB_SPEED_FULL : +/* EPS 0 means "full" */ +if (type !=PIPE_INTERRUPT ) + info1 |= (FOTG210_TUNE_RL_TT <<28 ); +if (type ==PIPE_CONTROL ) { + info1 |=QH_CONTROL_EP ;/* for TT */ + info1 |=QH_TOGGLE_CTL ;/* toggle from qtd */ + } + info1 |= maxp <<16 ; + + info2 |= (FOTG210_TUNE_MULT_TT <<30 ); + +/* Some Freescale processors have an erratum in which the +* port number in the queue head was 0..N-1 instead of 1..N. +*/ +if (fotg210_has_fsl_portno_bug (fotg210)) + info2 |= (urb->dev->ttport-1 ) <<23 ; +else + info2 |= urb->dev->ttport <<23 ; + +/* set the address of the TT; for TDI's integrated +* root hub tt, leave it zeroed. +*/ +if (tt && tt->hub !=fotg210_to_hcd (fotg210)->self.root_hub) + info2 |= tt->hub->devnum <<16 ; + +/* NOTE: if (PIPE_INTERRUPT) { scheduler sets c-mask } */ +Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
1.7.4.1
Part of the diff is not shown here. View the raw message.
Quoted 8 lines · Yuan-Hsin Chen
FOTG210 is an OTG controller which can be configured as an USB2.0 host. FOTG210 host is an ehci-like controller with some differences. First, register layout of FOTG210 is incompatible with EHCI. Furthermore, FOTG210 is lack of siTDs which means iTDs are used for both HS and FS ISO transfer.
Signed-off-by Yuan-Hsin Chen <[email protected]>
Quoted 9 lines
--- drivers/usb/Makefile | 1 + drivers/usb/host/Kconfig | 12 + drivers/usb/host/Makefile | 1 + drivers/usb/host/fotg210-hcd.c | 5967 ++++++++++++++++++++++++++++++++++++++++ drivers/usb/host/fotg210.h | 746 +++++ 5 files changed, 6727 insertions(+), 0 deletions(-) create mode 100644 drivers/usb/host/fotg210-hcd.c create mode 100644 drivers/usb/host/fotg210.h
You obviously didn't even run this through checkpatch.pl, did you?
$ ./scripts/checkpatch.pl --terse ../usb.mbox | tail -n 1 total: 138 errors, 618 warnings, 6742 lines checked
Please fix all of these if you wish us to at least start reviewing the patch. Your internal Q/A should have caught this first, please be more careful in the future.
thanks,
greg k-h
Hi,
Quoted 19 lines · Greg KH
Quoted 8 lines · Yuan-Hsin Chen
FOTG210 is an OTG controller which can be configured as an USB2.0 host. FOTG210 host is an ehci-like controller with some differences. First, register layout of FOTG210 is incompatible with EHCI. Furthermore, FOTG210 is lack of siTDs which means iTDs are used for both HS and FS ISO transfer.
Signed-off-by Yuan-Hsin Chen <[email protected]>Quoted 9 lines
--- drivers/usb/Makefile | 1 + drivers/usb/host/Kconfig | 12 + drivers/usb/host/Makefile | 1 + drivers/usb/host/fotg210-hcd.c | 5967 ++++++++++++++++++++++++++++++++++++++++ drivers/usb/host/fotg210.h | 746 +++++ 5 files changed, 6727 insertions(+), 0 deletions(-) create mode 100644 drivers/usb/host/fotg210-hcd.c create mode 100644 drivers/usb/host/fotg210.h
Quoted 9 lines
You obviously didn't even run this through checkpatch.pl, did you?
$ ./scripts/checkpatch.pl --terse ../usb.mbox | tail -n 1 total: 138 errors, 618 warnings, 6742 lines checkedPlease fix all of these if you wish us to at least start reviewing the patch. Your internal Q/A should have caught this first, please be more careful in the future.
Actually I did run checkpatch.pl and found that almost all errors and warnings are from ehci core (ehci-hcd.c, ehci-hub.c and so on) where my driver borrowed most of code.
$ ./scripts/checkpatch.pl --terse -f drivers/usb/host/ehci-hub.c | tail -n 1 total: 18 errors, 69 warnings, 1138 lines checked
$ ./scripts/checkpatch.pl --terse -f drivers/usb/host/ehci-hcd.c | tail -n 1 total: 17 errors, 78 warnings, 1403 lines checked
So you're saying that I should fix them, is that right?
thanks,
Yuan-Hsin
Quoted 3 lines
thanks,
greg k-h
Quoted 36 lines · Yuan-Hsin Chen
Hi,
Quoted 19 lines · Greg KH
Quoted 8 lines · Yuan-Hsin Chen
FOTG210 is an OTG controller which can be configured as an USB2.0 host. FOTG210 host is an ehci-like controller with some differences. First, register layout of FOTG210 is incompatible with EHCI. Furthermore, FOTG210 is lack of siTDs which means iTDs are used for both HS and FS ISO transfer.
Signed-off-by Yuan-Hsin Chen <[email protected]>Quoted 9 lines
--- drivers/usb/Makefile | 1 + drivers/usb/host/Kconfig | 12 + drivers/usb/host/Makefile | 1 + drivers/usb/host/fotg210-hcd.c | 5967 ++++++++++++++++++++++++++++++++++++++++ drivers/usb/host/fotg210.h | 746 +++++ 5 files changed, 6727 insertions(+), 0 deletions(-) create mode 100644 drivers/usb/host/fotg210-hcd.c create mode 100644 drivers/usb/host/fotg210.hQuoted 9 lines
You obviously didn't even run this through checkpatch.pl, did you?
$ ./scripts/checkpatch.pl --terse ../usb.mbox | tail -n 1 total: 138 errors, 618 warnings, 6742 lines checkedPlease fix all of these if you wish us to at least start reviewing the patch. Your internal Q/A should have caught this first, please be more careful in the future.
Actually I did run checkpatch.pl and found that almost all errors and warnings are from ehci core (
ehci-hcd.c,ehci-hub.cand so on) where my driver borrowed most of code.
Quoted 7 lines
$ ./scripts/checkpatch.pl --terse -f drivers/usb/host/ehci-hub.c | tail -n 1 total: 18 errors, 69 warnings, 1138 lines checked$ ./scripts/checkpatch.pl --terse -f drivers/usb/host/ehci-hcd.c | tail -n 1 total: 17 errors, 78 warnings, 1403 lines checkedSo you're saying that I should fix them, is that right?
In that case, no, you should be figuring out how to refactor and reuse the EHCI code instead of copying it straight into your driver.
Sarah Sharp
Hi,
Quoted 40 lines · Sarah Sharp
Quoted 39 lines · Yuan-Hsin Chen
Hi,
Quoted 19 lines · Greg KH
Quoted 8 lines · Yuan-Hsin Chen
FOTG210 is an OTG controller which can be configured as an USB2.0 host. FOTG210 host is an ehci-like controller with some differences. First, register layout of FOTG210 is incompatible with EHCI. Furthermore, FOTG210 is lack of siTDs which means iTDs are used for both HS and FS ISO transfer.
Signed-off-by Yuan-Hsin Chen <[email protected]>Quoted 9 lines
--- drivers/usb/Makefile | 1 + drivers/usb/host/Kconfig | 12 + drivers/usb/host/Makefile | 1 + drivers/usb/host/fotg210-hcd.c | 5967 ++++++++++++++++++++++++++++++++++++++++ drivers/usb/host/fotg210.h | 746 +++++ 5 files changed, 6727 insertions(+), 0 deletions(-) create mode 100644 drivers/usb/host/fotg210-hcd.c create mode 100644 drivers/usb/host/fotg210.hQuoted 9 lines
You obviously didn't even run this through checkpatch.pl, did you?
$ ./scripts/checkpatch.pl --terse ../usb.mbox | tail -n 1 total: 138 errors, 618 warnings, 6742 lines checkedPlease fix all of these if you wish us to at least start reviewing the patch. Your internal Q/A should have caught this first, please be more careful in the future.
Actually I did run checkpatch.pl and found that almost all errors and warnings are from ehci core (
ehci-hcd.c,ehci-hub.cand so on) where my driver borrowed most of code.$ ./scripts/checkpatch.pl --terse -f drivers/usb/host/ehci-hub.c | tail -n 1 total: 18 errors, 69 warnings, 1138 lines checked
Quoted 7 lines
Quoted 4 lines
$ ./scripts/checkpatch.pl --terse -f drivers/usb/host/ehci-hcd.c | tail -n 1 total: 17 errors, 78 warnings, 1403 lines checkedSo you're saying that I should fix them, is that right?
In that case, no, you should be figuring out how to refactor and reuse the EHCI code instead of copying it straight into your driver.
I was trying to use ehci-platform.c, anonymous union/struct, and quirk flags to avoid copying EHCI code.
But there are too big incompatibilities between fotg210/fusbh200 controller and EHCI.
That's why Alan agreed that I could create a stand-alone driver for fusbh200 host controller.
Since fotg210 and fusbh200 have the same issue, fotg210 hcd is supposed to be stand-alone.
More details please refer to mail sequence
http://www.spinics.net/lists/linux-usb/msg83812.html
Thanks,
Yuan-Hsin
Quoted 2 lines
Sarah Sharp
Quoted 13 lines · Yuan-Hsin Chen
Quoted 2 lines
In that case, no, you should be figuring out how to refactor and reuse the EHCI code instead of copying it straight into your driver.
I was trying to use
ehci-platform.c, anonymous union/struct, and quirk flags to avoid copying EHCI code.
But there are too big incompatibilities between fotg210/fusbh200 controller and EHCI.
That's why Alan agreed that I could create a stand-alone driver for fusbh200 host controller.
Since fotg210 and fusbh200 have the same issue, fotg210 hcd is supposed to be stand-alone.
More details please refer to mail sequence
http://www.spinics.net/lists/linux-usb/msg83812.html
That's right. The patch's description mentions some of the incompatibilities. In short, the Faraday controllers are a _very_ noncompliant EHCI variant. The changes needed to make ehci-hcd work with them were too invasive IMO.
It's a shame, because so much of the code is the same. It makes you want to go back and ask those Faraday engineers what they were thinking of at the time.
Alan Stern
Quoted 16 lines · Alan Stern
Quoted 13 lines · Yuan-Hsin Chen
Quoted 2 lines
In that case, no, you should be figuring out how to refactor and reuse the EHCI code instead of copying it straight into your driver.
I was trying to use
ehci-platform.c, anonymous union/struct, and quirk flags to avoid copying EHCI code.
But there are too big incompatibilities between fotg210/fusbh200 controller and EHCI.
That's why Alan agreed that I could create a stand-alone driver for fusbh200 host controller.
Since fotg210 and fusbh200 have the same issue, fotg210 hcd is supposed to be stand-alone.
More details please refer to mail sequence
http://www.spinics.net/lists/linux-usb/msg83812.html
Quoted 8 lines
That's right. The patch's description mentions some of the incompatibilities. In short, the Faraday controllers are a _very_ noncompliant EHCI variant. The changes needed to make ehci-hcd work with them were too invasive IMO.
It's a shame, because so much of the code is the same. It makes you want to go back and ask those Faraday engineers what they were thinking of at the time.
Ah, ok, that's too bad. I understand why the code can't be refactored.
Sarah Sharp
Quoted 36 lines · Yuan-Hsin Chen
Hi,
Quoted 19 lines · Greg KH
Quoted 8 lines · Yuan-Hsin Chen
FOTG210 is an OTG controller which can be configured as an USB2.0 host. FOTG210 host is an ehci-like controller with some differences. First, register layout of FOTG210 is incompatible with EHCI. Furthermore, FOTG210 is lack of siTDs which means iTDs are used for both HS and FS ISO transfer.
Signed-off-by Yuan-Hsin Chen <[email protected]>Quoted 9 lines
--- drivers/usb/Makefile | 1 + drivers/usb/host/Kconfig | 12 + drivers/usb/host/Makefile | 1 + drivers/usb/host/fotg210-hcd.c | 5967 ++++++++++++++++++++++++++++++++++++++++ drivers/usb/host/fotg210.h | 746 +++++ 5 files changed, 6727 insertions(+), 0 deletions(-) create mode 100644 drivers/usb/host/fotg210-hcd.c create mode 100644 drivers/usb/host/fotg210.hQuoted 9 lines
You obviously didn't even run this through checkpatch.pl, did you?
$ ./scripts/checkpatch.pl --terse ../usb.mbox | tail -n 1 total: 138 errors, 618 warnings, 6742 lines checkedPlease fix all of these if you wish us to at least start reviewing the patch. Your internal Q/A should have caught this first, please be more careful in the future.
Actually I did run checkpatch.pl and found that almost all errors and warnings are from ehci core (
ehci-hcd.c,ehci-hub.cand so on) where my driver borrowed most of code.
Quoted 7 lines
$ ./scripts/checkpatch.pl --terse -f drivers/usb/host/ehci-hub.c | tail -n 1 total: 18 errors, 69 warnings, 1138 lines checked$ ./scripts/checkpatch.pl --terse -f drivers/usb/host/ehci-hcd.c | tail -n 1 total: 17 errors, 78 warnings, 1403 lines checkedSo you're saying that I should fix them, is that right?
At the very least, yes, you should. And those tiny numbers of errors do not line up with the much larger number of errors in your patch submission, so it isn't just a "copy and paste" issue here.
thanks,
greg k-h
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 8 lines · Yuan-Hsin Chen
FOTG210 is an OTG controller which can be configured as an USB2.0 host. FOTG210 host is an ehci-like controller with some differences. First, register layout of FOTG210 is incompatible with EHCI. Furthermore, FOTG210 is lack of siTDs which means iTDs are used for both HS and FS ISO transfer.
Signed-off-by Yuan-Hsin Chen <[email protected]>
As your email now is bouncing, I'm going to revert this patch, I can't take a patch for a driver with no active maintainer, sorry.
If someone else from Faraday will step up and maintain this, that would be great, please resend it with your email information.
thanks,
greg k-h
Hi,
Quoted 9 lines · Greg KH
Quoted 7 lines · Yuan-Hsin Chen
FOTG210 is an OTG controller which can be configured as an USB2.0 host. FOTG210 host is an ehci-like controller with some differences. First, register layout of FOTG210 is incompatible with EHCI. Furthermore, FOTG210 is lack of siTDs which means iTDs are used for both HS and FS ISO transfer.
Quoted 7 lines
Quoted 1 line
Signed-off-by Yuan-Hsin Chen <[email protected]>As your email now is bouncing, I'm going to revert this patch, I can't take a patch for a driver with no active maintainer, sorry.
If someone else from Faraday will step up and maintain this, that would be great, please resend it with your email information.
I see. My ex-colleague who takes over the driver will resend the patch later.
Thanks.
Yuan-Hsin
Quoted 4 lines
thanks,
greg k-h