Skip to contentSkip to conversation

regulator: pfuze100: A few small questions

DISCUSSION Axel Lin 2 participants 7 messages Jul 29, 2013 – Jul 30, 2013

lore
Share & tools
lore

Axel Lin

author
#0 lore raw

Hi Robin,
2 questions about the code in pfuze100 driver:

1)
Both PFUZE100_REVID and PFUZE100_FABID are defined as 0x3. So I'm wondering if it's a typo in one of the register address? If they are actually the same register, we don't need to read the same register twice in pfuze_identify().

2)
What is the the purpose of stby_reg and stby_mask? Seems current code does not use it?

author
#1 lore raw

2013/7/29 Axel Lin <[email protected]>:

Quoted 9 lines

Hi Robin,
2 questions about the code in pfuze100 driver:

1)
Both PFUZE100_REVID and PFUZE100_FABID are defined as 0x3. So I'm wondering if it's a typo in one of the register address? If they are actually the same register, we don't need to read the same register twice in pfuze_identify().

Quoted 3 lines

2)
What is the the purpose of stby_reg and stby_mask? Seems current code does not use it?

One more question:

Current code adjust min_uV and uV_step when SW2~SW4 high bit is set. I'm wondering if n_voltages is correct or not in this case because the n_voltages is calculated by original equation (max-min/step + 1). What is the max_uV when SW2~SW4 high bit is set?

Regards,
Axel

#2 lore raw
Quoted 9 lines · Axel Lin

2013/7/29 Axel Lin <[email protected]>:

Quoted 8 lines

Hi Robin,
2 questions about the code in pfuze100 driver:

1)
Both PFUZE100_REVID and PFUZE100_FABID are defined as 0x3. So I'm wondering if it's a typo in one of the register address? If they are actually the same register, we don't need to read the same register twice in pfuze_identify().

Yes, It's a typo, I will correct it.

Quoted 4 lines
Quoted 4 lines

2)
What is the the purpose of stby_reg and stby_mask? Seems current code does not use it?

They are only kept place. These reg bits are used to set standby voltage, I will finish it in the future.

Quoted 9 lines

One more question:

Current code adjust min_uV and uV_step when SW2~SW4 high bit is set. I'm wondering if n_voltages is correct or not in this case because the n_voltages is calculated by original equation (max-min/step + 1). What is the max_uV when SW2~SW4 high bit is set?

If high bit set(bit6, bit0~5:vsel), min_uV/step will change from 0.4V/25mV to 0.8V/50mV,but the n_voltages will kept the same.
For example,SW2 will vary from 0.4V to 1.975V(0x0~0x3f),if bit6 set 0(high bit) SW2 will vary from 0.8V to 3.3V(0x40~0x72,0x72~0x7f:reversed). Please ignore bit7 or consider it as 0.

Quoted 3 lines

Regards,
Axel

author
#3 lore raw
Quoted 10 lines
Quoted 5 lines

Current code adjust min_uV and uV_step when SW2~SW4 high bit is set. I'm wondering if n_voltages is correct or not in this case because the n_voltages is calculated by original equation (max-min/step + 1). What is the max_uV when SW2~SW4 high bit is set?

If high bit set(bit6, bit0~5:vsel), min_uV/step will change from 0.4V/25mV to 0.8V/50mV,but the n_voltages will kept the same.
For example,SW2 will vary from 0.4V to 1.975V(0x0~0x3f),if bit6 set 0(high bit) SW2 will vary from 0.8V to 3.3V(0x40~0x72,0x72~0x7f:reversed). Please ignore bit7 or consider it as 0.

Hi Robin,
According to your description:

BIT6 is clear: 0.4V ~ 1.975V , step 25mV (0x0~0x3f)
BIT6 is set:   0.8V ~ 3.3V, step 50mV    (0x40~0x72,0x72~0x7f:reversed)

For SW2/SW3A/SW3B/SW4:
I think current implementation is wrong.
The supported voltage range should cover the whole range: 0.4V ~ 3.3V.

You need to implement set_voltage_sel/get_voltage_sel:
For 0.4V ~ 1.975V, use 25mV step and clear BIT6. For 2V ~ 3.3V, use 50mV step and set BIT6

And use regulator_list_voltage_linear_range / regulator_map_voltage_linear_range

Below list the register value and voltage mapping:

reg volt (reg with BIT6 is set)
================================

0x00    400000
0x01    425000
0x02    450000
0x03    475000
0x04    500000
...     ......
0x0e    750000
0x0f    775000
0x10    800000  (0x40)
0x11    825000
0x12    850000  (0x41)
0x13    875000
0x14    900000  (0x42)
0x15    925000
0x16    950000  (0x43)
0x17    975000
0x18    1000000 (0x44)
0x19    1025000
0x1a    1050000 (0x45)
0x1b    1075000
0x1c    1100000 (0x46)
0x1d    1125000
0x1e    1150000 (0x47)
0x1f    1175000
...     .......
0x3c    1950000 (0x57)
0x3f    1975000
        2000000 (0x58)
        2050000 (0x59)
        2100000 (0x5a)
        .....
        3300000 (0x72)

Regards,
Axel

#4 lore raw
Quoted 11 lines · Axel Lin
Quoted 10 lines
Quoted 5 lines

Current code adjust min_uV and uV_step when SW2~SW4 high bit is set. I'm wondering if n_voltages is correct or not in this case because the n_voltages is calculated by original equation (max-min/step + 1). What is the max_uV when SW2~SW4 high bit is set?

If high bit set(bit6, bit0~5:vsel), min_uV/step will change from 0.4V/25mV to 0.8V/50mV,but the n_voltages will kept the same.
For example,SW2 will vary from 0.4V to 1.975V(0x0~0x3f),if bit6 set 0(high bit) SW2 will vary from 0.8V to 3.3V(0x40~0x72,0x72~0x7f:reversed). Please ignore bit7 or consider it as 0.

Quoted 9 lines

Hi Robin,
According to your description:

BIT6 is clear: 0.4V ~ 1.975V , step 25mV (0x0~0x3f)
BIT6 is set:   0.8V ~ 3.3V, step 50mV    (0x40~0x72,0x72~0x7f:reversed)

For SW2/SW3A/SW3B/SW4:
I think current implementation is wrong.
The supported voltage range should cover the whole range: 0.4V ~ 3.3V.

Hi Alex,
Yes,the default setting of SW2 ~SW4in the regulator array is 0.4V~1.975V (Bit6 clear),and my code will check the true setting of Bit6. If Bit6=1 I will change min_uV from 0.4V to 0.8V ,step from 25mV to 50mV as what hardware define. I don't think we should mix the two define as what you mean 0.4V~3.3V. Because for every pfuze100 chip, the voltage of SW2~SW4 is 0.4V~1.975V or 0.8V~3.3V, not 0.4V~3.3V(from software view,Bit6 only readable).

Quoted 4 lines

You need to implement set_voltage_sel/get_voltage_sel:
For 0.4V ~ 1.975V, use 25mV step and clear BIT6. For 2V ~ 3.3V, use 50mV step and set BIT6

No,should be:
For 0.8V~3.3V, use 50mV step if set BIT6

Quoted 2 lines

And use regulator_list_voltage_linear_range / regulator_map_voltage_linear_range

Yes, I have used regulator_list_voltage_linear to list voltage, so that regulator core will regulator_map_voltage_linear to find the right voltage.

Quoted 28 lines

Below list the register value and voltage mapping:

reg volt (reg with BIT6 is set)
================================

0x00    400000
0x01    425000
0x02    450000
0x03    475000
0x04    500000
...     ......
0x0e    750000
0x0f    775000
0x10    800000  (0x40)
0x11    825000
0x12    850000  (0x41)
0x13    875000
0x14    900000  (0x42)
0x15    925000
0x16    950000  (0x43)
0x17    975000
0x18    1000000 (0x44)
0x19    1025000
0x1a    1050000 (0x45)
0x1b    1075000
0x1c    1100000 (0x46)
0x1d    1125000
0x1e    1150000 (0x47)
0x1f    1175000
Quoted 9 lines
...     .......
0x3c    1950000 (0x57)
0x3f    1975000
        2000000 (0x58)
        2050000 (0x59)
        2100000 (0x5a)
        .....
        3300000 (0x72)

Great, the voltage mapping is right.

Quoted 3 lines

Regards,
Axel

author
#5 lore raw

2013/7/30 Robin Gong <[email protected]>:

Quoted 17 lines · Axel Lin
Quoted 16 lines
Quoted 10 lines
Quoted 5 lines

Current code adjust min_uV and uV_step when SW2~SW4 high bit is set. I'm wondering if n_voltages is correct or not in this case because the n_voltages is calculated by original equation (max-min/step + 1). What is the max_uV when SW2~SW4 high bit is set?

If high bit set(bit6, bit0~5:vsel), min_uV/step will change from 0.4V/25mV to 0.8V/50mV,but the n_voltages will kept the same.
For example,SW2 will vary from 0.4V to 1.975V(0x0~0x3f),if bit6 set 0(high bit) SW2 will vary from 0.8V to 3.3V(0x40~0x72,0x72~0x7f:reversed). Please ignore bit7 or consider it as 0.

Hi Robin,
According to your description:

BIT6 is clear: 0.4V ~ 1.975V , step 25mV (0x0~0x3f)
BIT6 is set:   0.8V ~ 3.3V, step 50mV    (0x40~0x72,0x72~0x7f:reversed)
Quoted 5 lines
Quoted 4 lines

For SW2/SW3A/SW3B/SW4:
I think current implementation is wrong.
The supported voltage range should cover the whole range: 0.4V ~ 3.3V.

Hi Alex,

Errh... It's "Axel".

Quoted 7 lines

Yes,the default setting of SW2 ~SW4in the regulator array is 0.4V~1.975V (Bit6 clear),and my code will check the true setting of Bit6. If Bit6=1 I will change min_uV from 0.4V to 0.8V ,step from 25mV to 50mV as what hardware define. I don't think we should mix the two define as what you mean 0.4V~3.3V. Because for every pfuze100 chip, the voltage of SW2~SW4 is 0.4V~1.975V or 0.8V~3.3V, not 0.4V~3.3V(from software view,Bit6 only readable).

Well, if Bit6 is read-only then current code make sense.

Regards,
Axel

#6 lore raw
Quoted 18 lines · Axel Lin

2013/7/30 Robin Gong <[email protected]>:

Quoted 17 lines · Axel Lin
Quoted 16 lines
Quoted 10 lines
Quoted 5 lines

Current code adjust min_uV and uV_step when SW2~SW4 high bit is set. I'm wondering if n_voltages is correct or not in this case because the n_voltages is calculated by original equation (max-min/step + 1). What is the max_uV when SW2~SW4 high bit is set?

If high bit set(bit6, bit0~5:vsel), min_uV/step will change from 0.4V/25mV to 0.8V/50mV,but the n_voltages will kept the same.
For example,SW2 will vary from 0.4V to 1.975V(0x0~0x3f),if bit6 set 0(high bit) SW2 will vary from 0.8V to 3.3V(0x40~0x72,0x72~0x7f:reversed). Please ignore bit7 or consider it as 0.

Hi Robin,
According to your description:

BIT6 is clear: 0.4V ~ 1.975V , step 25mV (0x0~0x3f)
BIT6 is set:   0.8V ~ 3.3V, step 50mV    (0x40~0x72,0x72~0x7f:reversed)
Quoted 7 lines
Quoted 5 lines
Quoted 4 lines

For SW2/SW3A/SW3B/SW4:
I think current implementation is wrong.
The supported voltage range should cover the whole range: 0.4V ~ 3.3V.

Hi Alex,

Errh... It's "Axel".

Sorry...And thanks for your great catch.

Quoted 12 lines
Quoted 7 lines

Yes,the default setting of SW2 ~SW4in the regulator array is 0.4V~1.975V (Bit6 clear),and my code will check the true setting of Bit6. If Bit6=1 I will change min_uV from 0.4V to 0.8V ,step from 25mV to 50mV as what hardware define. I don't think we should mix the two define as what you mean 0.4V~3.3V. Because for every pfuze100 chip, the voltage of SW2~SW4 is 0.4V~1.975V or 0.8V~3.3V, not 0.4V~3.3V(from software view,Bit6 only readable).

Well, if Bit6 is read-only then current code make sense.

Regards,
Axel