Skip to contentSkip to conversation

usb: Move definition of USB_EHCI_BIG_ENDIAN_MMIO et al. out side of the ifs.

PATCH In review David Daney 2 participants 2 messages Aug 10, 2013 USB

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 usb: Move definition of USB_EHCI_BIG_ENDIAN_MMIO et al. out side of the ifs.

From: David Daney <[email protected]>

When CONFIG_USB_SUPPORT is not selected we get things like:

scripts/kconfig/mconf Kconfig
warning: (MIPS_SEAD3 && PMC_MSP && CPU_CAVIUM_OCTEON) selects USB_EHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)

It is much cleaner to make the various system Kconfigs select USB_EHCI_BIG_ENDIAN_MMIO rather than move the system config information into USB's Kconfig, but the warnings are annoying.

Eliminate the warning by moving the definition of USB_EHCI_BIG_ENDIAN_MMIO outside of all the Kconfig if statements. While we are at it move USB_OHCI_BIG_ENDIAN_DESC, USB_OHCI_BIG_ENDIAN_MMIO, USB_OHCI_LITTLE_ENDIAN and USB_EHCI_BIG_ENDIAN_DESC too, as they could very well suffer similar problems for other systems.

Get rid of the redundant "default n" in USB_OHCI_BIG_ENDIAN_DESC and USB_OHCI_BIG_ENDIAN_MMIO

---

Change from v1: Added USB_OHCI_BIG_ENDIAN_DESC, USB_OHCI_BIG_ENDIAN_MMIO, USB_OHCI_LITTLE_ENDIAN and USB_EHCI_BIG_ENDIAN_DESC to the set of symbols moved.

 drivers/usb/Kconfig      | 17 +++++++++++++++++
 drivers/usb/host/Kconfig | 20 --------------------
 2 files changed, 17 insertions(+), 20 deletions(-)
drivers/usb/Kconfig +17 -0
index 73f62ca..2642b8a 100644
@@ -6,9 +6,26 @@
 config USB_ARCH_HAS_OHCI
 	bool
 
+config USB_OHCI_BIG_ENDIAN_DESC
+	bool
+
+config USB_OHCI_BIG_ENDIAN_MMIO
+	bool
+
+config USB_OHCI_LITTLE_ENDIAN
+	bool
+	default n if STB03xxx || PPC_MPC52xx
+	default y
+
 config USB_ARCH_HAS_EHCI
 	bool
 
+config USB_EHCI_BIG_ENDIAN_MMIO
+	bool
+
+config USB_EHCI_BIG_ENDIAN_DESC
+	bool
+
 config USB_ARCH_HAS_XHCI
 	bool
 
drivers/usb/host/Kconfig +0 -20
index 8e8e694..e3ea970 100644
@@ -113,12 +113,6 @@ config USB_EHCI_HCD_PMC_MSP
 		Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's.
 		If unsure, say N.
 
-config USB_EHCI_BIG_ENDIAN_MMIO
-	bool
-
-config USB_EHCI_BIG_ENDIAN_DESC
-	bool
-
 config XPS_USB_HCD_XILINX
 	bool "Use Xilinx usb host EHCI controller core"
 	depends on (PPC32 || MICROBLAZE)
@@ -506,20 +500,6 @@ config USB_OCTEON_OHCI
 	  controller.  It is needed for low-speed USB 1.0 device
 	  support.  All CN6XXX based chips with USB are supported.
 
-
-config USB_OHCI_BIG_ENDIAN_DESC
-	bool
-	default n
-
-config USB_OHCI_BIG_ENDIAN_MMIO
-	bool
-	default n
-
-config USB_OHCI_LITTLE_ENDIAN
-	bool
-	default n if STB03xxx || PPC_MPC52xx
-	default y
-
 endif # USB_OHCI_HCD
 
 config USB_UHCI_HCD
Signature · 1 line
1.7.11.7
Acked-by on v2 1/1
#1 lore raw
Quoted 21 lines · David Daney

From: David Daney <[email protected]>

When CONFIG_USB_SUPPORT is not selected we get things like:

scripts/kconfig/mconf Kconfig
warning: (MIPS_SEAD3 && PMC_MSP && CPU_CAVIUM_OCTEON) selects USB_EHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)

It is much cleaner to make the various system Kconfigs select USB_EHCI_BIG_ENDIAN_MMIO rather than move the system config information into USB's Kconfig, but the warnings are annoying.

Eliminate the warning by moving the definition of USB_EHCI_BIG_ENDIAN_MMIO outside of all the Kconfig if statements. While we are at it move USB_OHCI_BIG_ENDIAN_DESC, USB_OHCI_BIG_ENDIAN_MMIO, USB_OHCI_LITTLE_ENDIAN and USB_EHCI_BIG_ENDIAN_DESC too, as they could very well suffer similar problems for other systems.

Get rid of the redundant "default n" in USB_OHCI_BIG_ENDIAN_DESC and USB_OHCI_BIG_ENDIAN_MMIO

Quoted 7 lines

---

Change from v1: Added USB_OHCI_BIG_ENDIAN_DESC, USB_OHCI_BIG_ENDIAN_MMIO, USB_OHCI_LITTLE_ENDIAN and USB_EHCI_BIG_ENDIAN_DESC to the set of symbols moved.