Skip to contentSkip to conversation

huawei usb dongle e173 not working on tumbleweed

opensuse-factory Ron Brickle 2 participants 3 messages Oct 3, 2013 – Oct 4, 2013 4 messages not in the archive

lore
Share & tools
lore
#4 lore raw
In reply to a message not in the archive
Quoted 69 lines · Larry Finger
Quoted 50 lines · Ron Brickle
Quoted 16 lines · Larry Finger
Quoted 6 lines · Ron Brickle

Hi I have been trying to get my huawei usb dongle working on Tumbleweed but to no avail so in desperation I am sending this email. it works fine on 12.3 opensuse so hopefully you can fix this problem I tried to get it working from help from the tumbleweed forum it is recognized in lsusb but doesn show in network-manager
regards and thanks Ron Brickle

Firmware?

A device present in lsusb only means that it is connected to the USB system. For NM to have it, any firmware must be present, the wifi-enable switch for *ALL* devices must be on, the device must be recognized by some driver, and that driver must load and initialize correctly. From the information you provided, it is impossible to tell where it is failing.

Quoted 3 lines

Larry

Hi i just put this in terminal as normal user then as root

rpm -ql usb_modeswitch-data|grep 1446
it returns no answer and it should be this I am told if so the driver isnt installed for this usb modem TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506"

MessageContent="55534243123456780000000000000011062000000100000000000000000000" is this any help
regards ron
lsusb gives thisron@desktop:~> rpm -ql usb_modeswitch-data|grep 1446 ron@desktop:~> lsusb
Bus 001 Device 002: ID 8087:8008 Intel Corp.
Bus 002 Device 002: ID 8087:8000 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 046d:0809 Logitech, Inc. Webcam Pro 9000 Bus 002 Device 003: ID 174c:2074 ASMedia Technology Inc.
Bus 002 Device 004: ID 2109:2812
Bus 002 Device 007: ID 12d1:1446 Huawei Technologies Co., Ltd. E1552/E1800/E173 (HSPA modem)
Bus 002 Device 005: ID 046d:c526 Logitech, Inc. Nano Receiver
Bus 002 Device 006: ID 046d:c52b Logitech, Inc. Unifying Receiver and usb-devices gives this
Bus=02 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0

D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1446 Rev=00.00
S:  Manufacturer=HUAWEI Technology
S:  Product=HUAWEI Mobile
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Quoted 4 lines

Driver=usb-storage
I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
thanks for your reply regards ron

From the usb-devices output, the device obviously needs to be mode switched.

There may be a regression from the openSUSE 12.3 kernel (probably 3.7) to the one used by Tumbleweed. The usb-storage drivers are maintinaed by Matthew Dharm <[email protected]>. I suggest you contact him with a Cc to [email protected], [email protected], and [email protected] and and state your problem, that it worked in kernel 3.7, but fails in the kernel 3.XX with the XX replaced by the version returned by 'uname -r'.

Larry

#5 lore raw

Ron --

We're going to need the version numbers of both the kernel and the usb_modeswitch utility from both openSUSE 12.3 and Tumbleweed if we're going to make any sense of the situation.

Matt

Quoted 78 lines · Ron Brickle
Quoted 66 lines · Larry Finger
Quoted 50 lines · Ron Brickle
Quoted 16 lines · Larry Finger
Quoted 6 lines · Ron Brickle

Hi I have been trying to get my huawei usb dongle working on Tumbleweed but to no avail so in desperation I am sending this email. it works fine on 12.3 opensuse so hopefully you can fix this problem I tried to get it working from help from the tumbleweed forum it is recognized in lsusb but doesn show in network-manager
regards and thanks Ron Brickle

Firmware?

A device present in lsusb only means that it is connected to the USB system. For NM to have it, any firmware must be present, the wifi-enable switch for *ALL* devices must be on, the device must be recognized by some driver, and that driver must load and initialize correctly. From the information you provided, it is impossible to tell where it is failing.

Quoted 3 lines

Larry

Hi i just put this in terminal as normal user then as root

rpm -ql usb_modeswitch-data|grep 1446
it returns no answer and it should be this I am told if so the driver isnt installed for this usb modem TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506"

MessageContent="55534243123456780000000000000011062000000100000000000000000000" is this any help
regards ron
lsusb gives thisron@desktop:~> rpm -ql usb_modeswitch-data|grep 1446 ron@desktop:~> lsusb
Bus 001 Device 002: ID 8087:8008 Intel Corp.
Bus 002 Device 002: ID 8087:8000 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 046d:0809 Logitech, Inc. Webcam Pro 9000 Bus 002 Device 003: ID 174c:2074 ASMedia Technology Inc.
Bus 002 Device 004: ID 2109:2812
Bus 002 Device 007: ID 12d1:1446 Huawei Technologies Co., Ltd. E1552/E1800/E173 (HSPA modem)
Bus 002 Device 005: ID 046d:c526 Logitech, Inc. Nano Receiver
Bus 002 Device 006: ID 046d:c52b Logitech, Inc. Unifying Receiver and usb-devices gives this
Bus=02 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0

D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1446 Rev=00.00
S:  Manufacturer=HUAWEI Technology
S:  Product=HUAWEI Mobile
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Quoted 4 lines

Driver=usb-storage
I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
thanks for your reply regards ron

From the usb-devices output, the device obviously needs to be mode switched.

There may be a regression from the openSUSE 12.3 kernel (probably 3.7) to the one used by Tumbleweed. The usb-storage drivers are maintinaed by Matthew Dharm <[email protected]>. I suggest you contact him with a Cc to [email protected], [email protected], and [email protected] and and state your problem, that it worked in kernel 3.7, but fails in the kernel 3.XX with the XX replaced by the version returned by 'uname -r'.

Quoted 3 lines

Larry

--
You received this message because you are subscribed to the Google Groups "USB Mass Storage on Linux" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected].
Visit this group at http://groups.google.com/a/lists.one-eyed-alien.net/group/usb-storage/.
For more options, visit https://groups.google.com/a/lists.one-eyed-alien.net/groups/opt_out.

Signature · 2 lines
Matthew Dharm
Maintainer, USB Mass Storage driver for Linux
#6 lore raw

(Ron replied separately with kernel versions and usb_modeswitch versions.)

Ron, it appears that while Tumbleweed upgraded the kernel version, it didn't upgrade the usb_modeswitch version. You probably need a newer version to support that device. I just checked
http://www.draisberghof.de/usb_modeswitch/ and the current version (2.0.1) has support for your device.

You will either need to update your usb_modeswitch manually or get the Tumbleweed maintainers to do so.

Matt

Quoted 93 lines · Matthew Dharm

Ron --

We're going to need the version numbers of both the kernel and the usb_modeswitch utility from both openSUSE 12.3 and Tumbleweed if we're going to make any sense of the situation.

Matt

Quoted 72 lines · Ron Brickle
Quoted 66 lines · Larry Finger
Quoted 50 lines · Ron Brickle
Quoted 16 lines · Larry Finger
Quoted 6 lines · Ron Brickle

Hi I have been trying to get my huawei usb dongle working on Tumbleweed but to no avail so in desperation I am sending this email. it works fine on 12.3 opensuse so hopefully you can fix this problem I tried to get it working from help from the tumbleweed forum it is recognized in lsusb but doesn show in network-manager
regards and thanks Ron Brickle

Firmware?

A device present in lsusb only means that it is connected to the USB system. For NM to have it, any firmware must be present, the wifi-enable switch for *ALL* devices must be on, the device must be recognized by some driver, and that driver must load and initialize correctly. From the information you provided, it is impossible to tell where it is failing.

Quoted 3 lines

Larry

Hi i just put this in terminal as normal user then as root

rpm -ql usb_modeswitch-data|grep 1446
it returns no answer and it should be this I am told if so the driver isnt installed for this usb modem TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506"

MessageContent="55534243123456780000000000000011062000000100000000000000000000" is this any help
regards ron
lsusb gives thisron@desktop:~> rpm -ql usb_modeswitch-data|grep 1446 ron@desktop:~> lsusb
Bus 001 Device 002: ID 8087:8008 Intel Corp.
Bus 002 Device 002: ID 8087:8000 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 046d:0809 Logitech, Inc. Webcam Pro 9000 Bus 002 Device 003: ID 174c:2074 ASMedia Technology Inc.
Bus 002 Device 004: ID 2109:2812
Bus 002 Device 007: ID 12d1:1446 Huawei Technologies Co., Ltd. E1552/E1800/E173 (HSPA modem)
Bus 002 Device 005: ID 046d:c526 Logitech, Inc. Nano Receiver
Bus 002 Device 006: ID 046d:c52b Logitech, Inc. Unifying Receiver and usb-devices gives this
Bus=02 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0

D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1446 Rev=00.00
S:  Manufacturer=HUAWEI Technology
S:  Product=HUAWEI Mobile
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Quoted 4 lines

Driver=usb-storage
I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
thanks for your reply regards ron

From the usb-devices output, the device obviously needs to be mode switched.

There may be a regression from the openSUSE 12.3 kernel (probably 3.7) to the one used by Tumbleweed. The usb-storage drivers are maintinaed by Matthew Dharm <[email protected]>. I suggest you contact him with a Cc to [email protected], [email protected], and [email protected] and and state your problem, that it worked in kernel 3.7, but fails in the kernel 3.XX with the XX replaced by the version returned by 'uname -r'.

Quoted 3 lines

Larry

Quoted 6 lines

--
You received this message because you are subscribed to the Google Groups "USB Mass Storage on Linux" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected].
Visit this group at http://groups.google.com/a/lists.one-eyed-alien.net/group/usb-storage/.
For more options, visit https://groups.google.com/a/lists.one-eyed-alien.net/groups/opt_out.

--
Matthew Dharm
Maintainer, USB Mass Storage driver for Linux

Signature · 2 lines
Matthew Dharm
Maintainer, USB Mass Storage driver for Linux