Skip to contentSkip to conversation

T1040QDS: Add support of 2 stage NAND boot loader

PATCH Superseded Prabhakar Kushwaha 2 participants 2 messages Oct 25, 2013 – Nov 6, 2013

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 6/6 T1040QDS: Add support of 2 stage NAND boot loader

Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM(256K) and copy SPL(192K). This further initialise DDR using SPD and environment and copy u-boot(512 kb) from NAND to DDR. Finally SPL transer control to u-boot.

Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly

---
Based upon git://git.denx.de/u-boot-mpc85xx.git branch next

Changes for v2: sending as it is

 board/freescale/t1040qds/Makefile |    9 ++-
 board/freescale/t1040qds/README   |   33 ++++++++++
 board/freescale/t1040qds/ddr.c    |    7 ++-
 board/freescale/t1040qds/spl.c    |  122 +++++++++++++++++++++++++++++++++++++
 board/freescale/t1040qds/tlb.c    |    8 ++-
 boards.cfg                        |    1 +
 include/configs/T1040QDS.h        |   58 +++++++++++++++---
 7 files changed, 227 insertions(+), 11 deletions(-)
 create mode 100644 board/freescale/t1040qds/spl.c
board/freescale/t1040qds/Makefile +8 -1
index 8f0057b..8f3d7ef 100644
@@ -8,9 +8,16 @@ include $(TOPDIR)/config.mk
 
 LIB	= $(obj)lib$(BOARD).o
 
+ifdef CONFIG_SPL_BUILD
+COBJS-y += spl.o
+endif
+
+ifndef CONFIG_SPL_BUILD
 COBJS-y	+= $(BOARD).o
+COBJS-$(CONFIG_PCI) += pci.o
+endif
+
 COBJS-y	+= ddr.o
-COBJS-$(CONFIG_PCI)     += pci.o
 COBJS-y	+= law.o
 COBJS-y	+= tlb.o
 
board/freescale/t1040qds/README +33 -0
index f8b53b4..0e4d32e 100644
@@ -167,3 +167,36 @@ T1042 Personality
 --------------------
 T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit
 Ethernet switch. Rest of the blocks are same as T1040
+
+
+2 Stage boot loader
+-------------------
+PBL initialise the internal SRAM and copy SPL(192K) in SRAM.
+SPL further initialise DDR using SPD and environment variables and copy
+u-boot(512 KB) from flash to DDR.
+Finally SPL transer control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - Actual SPL size 96K + padding till 192K for extra code
+ - No relocation required
+
+ Run time view of SPL framework :-
+ -----------------------------------------------
+ Area        | Address                         |
+ -----------------------------------------------
+ GD, BD      | 0x0xFFFC0000 (4K)               |
+ -----------------------------------------------
+ HEAP        | 0xFFFC1000 (40K) grow downwards |
+ -----------------------------------------------
+ STACK       | 0xFFFD0000 (20K) grow upwards   |
+ -----------------------------------------------
+ U-boot SPL  | 0xfffD0000 -  0xfffffffc (192K) |
+ -----------------------------------------------
+
+Command to build 2 stage NAND boot loader
+ - modify RCW at board/freescale/t1040qds/t1040_rcw.cfg for nand boot
+     -66000002 00000000 fc027000 01000000
+     +66000002 00000000 ec106000 01000000
+ - make T1040QDS_NAND_config
+ - make u-boot-with-spl-pbl.bin
board/freescale/t1040qds/ddr.c +5 -2
index 4fd17da..dd2e0cb 100644
@@ -107,11 +107,14 @@ phys_size_t initdram(int board_type)
 
 	puts("Initializing....using SPD\n");
 
+#ifdef CONFIG_SPL_BUILD
 	dram_size = fsl_ddr_sdram();
 
 	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 	dram_size *= 0x100000;
-
-	puts("    DDR: ");
+#else
+	puts("DDR has been initialised by pre loader\n");
+	dram_size =  0x80000000;
+#endif
 	return dram_size;
 }
board/freescale/t1040qds/spl.c new file +122 -0

122 lines not on this page · raw message

board/freescale/t1040qds/tlb.c +7 -1
index 412c591..c733040 100644
@@ -52,7 +52,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
 		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
 		      0, 2, BOOKE_PAGESZ_256M, 1),
-
+#ifndef CONFIG_SPL_BUILD
 	/* *I*G* - PCI */
 	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -82,6 +82,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 8, BOOKE_PAGESZ_16M, 1),
 #endif
+#endif
 #ifdef CONFIG_SYS_DCSRBAR_PHYS
 	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -103,6 +104,11 @@ struct fsl_e_tlb_entry tlb_table[] = {
 		      0, 11, BOOKE_PAGESZ_4K, 1),
 #endif
 
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 17, BOOKE_PAGESZ_2G, 1)
+#endif
 };
 
 int num_tlb_entries = ARRAY_SIZE(tlb_table);
boards.cfg +1 -0
index 5e10125..295d952 100644
@@ -963,6 +963,7 @@ Active  powerpc     mpc85xx        -           freescale       t4qds
 Active  powerpc     mpc85xx        -           freescale       t4qds               T4240QDS_SPIFLASH                    T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000                                                                  -
 Active  powerpc     mpc85xx        -           freescale       t4qds               T4240QDS_SRIO_PCIE_BOOT              T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000                                                                  -
 Active  powerpc     mpc85xx        -           freescale       t1040qds            T1040QDS                             T1040QDS:PPC_T1040                                                                                                                Naveen Burmi <[email protected]>
+Active  powerpc     mpc85xx        -           freescale       t1040qds            T1040QDS_NAND                        T1040QDS:PPC_T1040,RAMBOOT_PBL,NAND                                                                                                      Poonam Aggrwal <[email protected]>
 Active  powerpc     mpc85xx        -           gdsys           p1022               controlcenterd_36BIT_SDCARD          controlcenterd:36BIT,SDCARD                                                                                                       Dirk Eibach <[email protected]>
 Active  powerpc     mpc85xx        -           gdsys           p1022               controlcenterd_36BIT_SDCARD_DEVELOP  controlcenterd:36BIT,SDCARD,DEVELOP                                                                                               Dirk Eibach <[email protected]>
 Active  powerpc     mpc85xx        -           gdsys           p1022               controlcenterd_TRAILBLAZER           controlcenterd:TRAILBLAZER,SPIFLASH                                                                                               Dirk Eibach <[email protected]>
include/configs/T1040QDS.h +51 -7

104 lines not on this page · raw message

Signature · 1 line
1.7.9.5
#1 lore raw

PATCH v2 6/6 T1040QDS: Add support of 2 stage NAND boot loader

Quoted 31 lines · Prabhakar Kushwaha

Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM(256K) and copy SPL(192K). This further initialise DDR using SPD and environment and copy u-boot(512 kb) from NAND to DDR. Finally SPL transer control to u-boot.

Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly

---
Based upon git://git.denx.de/u-boot-mpc85xx.git branch next

Changes for v2: sending as it is

 board/freescale/t1040qds/Makefile |    9 ++-
 board/freescale/t1040qds/README   |   33 ++++++++++
 board/freescale/t1040qds/ddr.c    |    7 ++-
 board/freescale/t1040qds/spl.c    |  122 +++++++++++++++++++++++++++++++++++++
 board/freescale/t1040qds/tlb.c    |    8 ++-
 boards.cfg                        |    1 +
 include/configs/T1040QDS.h        |   58 +++++++++++++++---
 7 files changed, 227 insertions(+), 11 deletions(-)
 create mode 100644 board/freescale/t1040qds/spl.c
board/freescale/t1040qds/Makefile +0 -0
index 8f0057b..8f3d7ef 100644
@@ -8,9 +8,16 @@ include $(TOPDIR)/config.mk
 

board/freescale/t1040qds/Makefile include $(TOPDIR)/config.mk · line 18

Quoted 10 lines
board/freescale/t1040qds/Makefile +7 -0
 LIB	= $(obj)lib$(BOARD).o
 
+ifdef CONFIG_SPL_BUILD
+COBJS-y += spl.o
+endif
+
+ifndef CONFIG_SPL_BUILD
 COBJS-y	+= $(BOARD).o
+COBJS-$(CONFIG_PCI) += pci.o
+endif

Use "else".

Quoted 17 lines
board/freescale/t1040qds/README +9 -0
index f8b53b4..0e4d32e 100644
@@ -167,3 +167,36 @@ T1042 Personality
 --------------------
 T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit
 Ethernet switch. Rest of the blocks are same as T1040
+
+
+2 Stage boot loader
+-------------------
+PBL initialise the internal SRAM and copy SPL(192K) in SRAM.
+SPL further initialise DDR using SPD and environment variables and copy
+u-boot(512 KB) from flash to DDR.
+Finally SPL transer control to u-boot for futher booting.
+

board/freescale/t1040qds/README T1042 Personality · line 188

Quoted 10 lines
board/freescale/t1040qds/README +10 -0
+SPL has following features:
+ - Executes within 256K
+ - Actual SPL size 96K + padding till 192K for extra code
+ - No relocation required
+
+ Run time view of SPL framework :-
+ -----------------------------------------------
+ Area        | Address                         |
+ -----------------------------------------------
+ GD, BD      | 0x0xFFFC0000 (4K)               |

s/0x0x/0x/

board/freescale/t1040qds/README T1042 Personality · line 195

Quoted 7 lines
board/freescale/t1040qds/README +7 -0
+ -----------------------------------------------
+ HEAP        | 0xFFFC1000 (40K) grow downwards |
+ -----------------------------------------------
+ STACK       | 0xFFFD0000 (20K) grow upwards   |
+ -----------------------------------------------
+ U-boot SPL  | 0xfffD0000 -  0xfffffffc (192K) |
+ -----------------------------------------------

Usually the heap grows upwards (or more accurately these days, a predefined area is given to malloc to allocate however it wants, assuming you haven't substituted some simple allocator) and the stack grows downwards (again ideally within a defined area).

I'd just remove the language about growing. It makes it ambiguous whether the addresses you provide are the start or the end of the range.

board/freescale/t1040qds/README T1042 Personality · line 202

Quoted 6 lines
board/freescale/t1040qds/README +6 -0
+Command to build 2 stage NAND boot loader
+ - modify RCW at board/freescale/t1040qds/t1040_rcw.cfg for nand boot
+     -66000002 00000000 fc027000 01000000
+     +66000002 00000000 ec106000 01000000
+ - make T1040QDS_NAND_config
+ - make u-boot-with-spl-pbl.bin

Please find some way for this RCW modification to happen automatically as part of the build process for NAND targets.

Could you describe what is being changed in the RCW?

Quoted 9 lines
board/freescale/t1040qds/ddr.c +1 -0
index 4fd17da..dd2e0cb 100644
@@ -107,11 +107,14 @@ phys_size_t initdram(int board_type)
 
 	puts("Initializing....using SPD\n");
 
+#ifdef CONFIG_SPL_BUILD

board/freescale/t1040qds/ddr.c phys_size_t initdram(int board_type) · line 118

Quoted 10 lines
board/freescale/t1040qds/ddr.c +4 -2
 	dram_size = fsl_ddr_sdram();
 
 	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 	dram_size *= 0x100000;
-
-	puts("    DDR: ");
+#else
+	puts("DDR has been initialised by pre loader\n");
+	dram_size =  0x80000000;
+#endif

PBI should not be initializing DDR -- only SRAM.

Quoted 29 lines
board/freescale/t1040qds/ddr.c +29 -0
+unsigned long get_board_sys_clk(void)
+{
+	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch (sysclk_conf & 0x0F) {
+	case QIXIS_SYSCLK_64:
+		return 64000000;
+	case QIXIS_SYSCLK_83:
+		return 83333333;
+	case QIXIS_SYSCLK_100:
+		return 100000000;
+	case QIXIS_SYSCLK_125:
+		return 125000000;
+	case QIXIS_SYSCLK_133:
+		return 133333333;
+	case QIXIS_SYSCLK_150:
+		return 150000000;
+	case QIXIS_SYSCLK_160:
+		return 160000000;
+	case QIXIS_SYSCLK_166:
+		return 166666666;
+	}
+	return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+

board/freescale/t1040qds/ddr.c phys_size_t initdram(int board_type)

Quoted 10 lines
board/freescale/t1040qds/ddr.c +10 -0
+	switch ((ddrclk_conf & 0x30) >> 4) {
+	case QIXIS_DDRCLK_100:
+		return 100000000;
+	case QIXIS_DDRCLK_125:
+		return 125000000;
+	case QIXIS_DDRCLK_133:
+		return 133333333;
+	}
+	return 66666666;
+}

Can you factor these out into a non-SPL-specific file?

Quoted 11 lines
board/freescale/t1040qds/ddr.c +11 -0
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, sys_clk, uart_clk;
+	u32 stack = CONFIG_SPL_RELOC_STACK;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+	console_init_f();
+
+	/* initialize selected port with appropriate baud rate */
+	sys_clk = get_board_sys_clk();
+	plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;

board/freescale/t1040qds/ddr.c

Quoted 10 lines
board/freescale/t1040qds/ddr.c +10 -0
+	uart_clk = sys_clk * plat_ratio / 2;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     uart_clk / 16 / CONFIG_BAUDRATE);
+
+	/* clear BSS segment */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* Set STACK pointer */
+	asm volatile ("lwz 1, %0" : : "m"(stack));

NACK

You cannot change the stack pointer behind the compiler's back.

board/freescale/t1040qds/ddr.c

Quoted 7 lines
board/freescale/t1040qds/ddr.c +7 -0
+	board_init_r(NULL, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	/* Pointer is writable since we allocated a register for it */
+	gd = (gd_t *)CONFIG_SPL_GD_ADDR;

Why don't you just pass CONFIG_SPL_GD_ADDR as the argument to board_init_r() instead of passing NULL and then setting it here?

Quoted 12 lines
board/freescale/t1040qds/ddr.c +12 -0
+	bd_t *bd;
+
+	memset(gd, 0, sizeof(gd_t));
+	bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t));
+	memset(bd, 0, sizeof(bd_t));
+	gd->bd = bd;
+	bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+	bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+	probecpu();
+	get_clocks();
+	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,

board/freescale/t1040qds/ddr.c

Quoted 10 lines
board/freescale/t1040qds/ddr.c +10 -0
+			CONFIG_SPL_RELOC_MALLOC_SIZE);
+	env_init();
+
+	/* relocate environment function pointers etc. */
+	env_relocate();
+
+	i2c_init(CONFIG_SYS_FSL_I2C_SPEED, CONFIG_SYS_FSL_I2C_SLAVE);
+
+	gd->ram_size = initdram(0);
+	puts("Second program loader running in sram...\n");

The SPL was executing in SRAM from the beginning. This message is not an appropriate way to say "I've initialized the DDR controller and done nothing with it so far".

board/freescale/t1040qds/ddr.c

Quoted 5 lines
board/freescale/t1040qds/ddr.c +5 -0
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 17, BOOKE_PAGESZ_2G, 1)
+#endif

MAS2_M

-Scott