Staging: bcm: DDRInit: removed extra lines
PATCH 7/9 Staging: bcm: DDRInit: removed extra lines
This is the seventh patch of a series.
Signed-off-by Gary Alan Rookard <[email protected]>
---
On branch staging-next
drivers/staging/bcm/DDRInit.c | 163 +++++++++++------------------------------- 1 file changed, 43 insertions(+), 120 deletions(-)
drivers/staging/bcm/DDRInit.c +43 -120
@@ -6,23 +6,21 @@#define MIPS_CLOCK_REG 0x0f000820/* DDR INIT-133Mhz */ -#define T3_SKIP_CLOCK_PROGRAM_DUMP_133MHZ 12 /* index for 0x0F00700 */0 +#define T3_SKIP_CLOCK_PROGRAM_DUMP_133MHZ 12/* index for 0x0F007000 */ static struct bcm_ddr_setting asT3_DDRSetting133MHz[] = {/* # DPLL Clock Setting */ {0x0F000800 ,0x00007212 }, {0x0f000820 ,0x07F13FFF }, {0x0f000810 ,0x00000F95 }, {0x0f000860 ,0x00000000 }, {0x0f000880 ,0x000003DD }, -/* Changed source for X-bar and MIPS clock to APLL */ - {0x0f000840 ,0x0FFF1B00 }, + {0x0f000840 ,0x0FFF1B00 },/* Changed source for X-bar and MIPS clock to APLL */ {0x0f000870 ,0x00000002 }, {0x0F00a044 ,0x1fffffff }, {0x0F00a040 ,0x1f000000 }, {0x0F00a084 ,0x1Cffffff }, {0x0F00a080 ,0x1C000000 }, {0x0F00a04C ,0x0000000C }, -/* Memcontroller Default values */ - {0x0F007000 ,0x00010001 }, + {0x0F007000 ,0x00010001 },/* Memcontroller Default values */ {0x0F007004 ,0x01010100 }, {0x0F007008 ,0x01000001 }, {0x0F00700c ,0x00000000 },
@@ -56,12 +54,9 @@ static struct bcm_ddr_setting asT3_DDRSetting133MHz[] = { /* # DPLL Clock Se {0x0F00707C, 0x00000000}, {0x0F007080, 0x00000000}, {0x0F007084, 0x00000000}, -/* # Enable BW improvement within memory controller */ - {0x0F007094, 0x00000104}, -/* # Enable 2 ports within X-bar */ - {0x0F00A000, 0x00000016}, -/* # Enable start bit within memory controller */ - {0x0F007018, 0x01010000} + {0x0F007094, 0x00000104}, /* # Enable BW improvement within memory controller */ + {0x0F00A000, 0x00000016}, /* # Enable 2 ports within X-bar */ + {0x0F007018, 0x01010000} /* # Enable start bit within memory controller */ };/* 80Mhz */ #define T3_SKIP_CLOCK_PROGRAM_DUMP_80MHZ 10/* index for 0x0F007000 */
@@ -76,8 +71,7 @@ static struct bcm_ddr_setting asT3_DDRSetting80MHz[] = { /* # DPLL Clock Settin {0x0F00a080, 0x1C000000}, {0x0F00a000, 0x00000016}, {0x0F00a04C, 0x0000000C}, -/* Memcontroller Default values */ - {0x0F007000, 0x00010001}, + {0x0F007000, 0x00010001}, /* Memcontroller Default values */ {0x0F007004, 0x01000000}, {0x0F007008, 0x01000001}, {0x0F00700c, 0x00000000},
@@ -112,8 +106,7 @@ static struct bcm_ddr_setting asT3_DDRSetting80MHz[] = { /* # DPLL Clock Settin {0x0F007080, 0x00000000}, {0x0F007084, 0x00000000}, {0x0F007094, 0x00000104}, -/*# Enable start bit within memory controller */ - {0x0F007018, 0x01010000} + {0x0F007018, 0x01010000} /* # Enable start bit within memory controller */ };/* 100Mhz */ #define T3_SKIP_CLOCK_PROGRAM_DUMP_100MHZ 13/* index for 0x0F007000 */
@@ -123,19 +116,16 @@ static struct bcm_ddr_setting asT3_DDRSetting100MHz[] = {/* # DPLL Clock Settin {0x0f000820, 0x07F13E3F}, {0x0f000860, 0x00000000}, {0x0f000880, 0x000003DD}, -/* Changed source for X-bar and MIPS clock to APLL */ -/* 0x0f000840,0x0FFF1800, */ - {0x0f000840, 0x0FFF1B00}, + {0x0f000840, 0x0FFF1B00}, /* Changed source for X-bar and MIPS clock to APLL */ +/* 0x0f000840,0x0FFF1800, */ {0x0f000870, 0x00000002}, {0x0F00a044, 0x1fffffff}, {0x0F00a040, 0x1f000000}, {0x0F00a084, 0x1Cffffff}, {0x0F00a080, 0x1C000000}, {0x0F00a04C, 0x0000000C}, -/* # Enable 2 ports within X-bar */ - {0x0F00A000, 0x00000016}, -/*Memcontroller Default values */ - {0x0F007000, 0x00010001}, + {0x0F00A000, 0x00000016}, /* # Enable 2 ports within X-bar */ + {0x0F007000, 0x00010001}, /*Memcontroller Default values */ {0x0F007004, 0x01010100}, {0x0F007008, 0x01000001}, {0x0F00700c, 0x00000000},
@@ -169,12 +159,9 @@ static struct bcm_ddr_setting asT3_DDRSetting100MHz[] = {/* # DPLL Clock Settin {0x0F00707C, 0x00000000}, {0x0F007080, 0x00000000}, {0x0F007084, 0x00000000}, -/* # Enable BW improvement within memory controller */ - {0x0F007094, 0x00000104}, -/* # Enable start bit within memory controller */ - {0x0F007018, 0x01010000} + {0x0F007094, 0x00000104}, /* # Enable BW improvement within memory controller */ + {0x0F007018, 0x01010000} /* # Enable start bit within memory controller */ }; -/* Net T3B DDR Settings */ /* DDR INIT-133Mhz */ static struct bcm_ddr_setting asDPLL_266MHZ[] = {
@@ -183,8 +170,7 @@ static struct bcm_ddr_setting asDPLL_266MHZ[] = { {0x0f000810, 0x00000F95}, {0x0f000860, 0x00000000}, {0x0f000880, 0x000003DD}, -/* Changed source for X-bar and MIPS clock to APLL */ - {0x0f000840, 0x0FFF1B00}, + {0x0f000840, 0x0FFF1B00}, /* Changed source for X-bar and MIPS clock to APLL */ {0x0f000870, 0x00000002} };
@@ -195,18 +181,14 @@ static struct bcm_ddr_setting asT3B_DDRSetting133MHz[] = {/* # DPLL Clock Settin {0x0f000810, 0x00000F95}, {0x0f000820, 0x07F13652}, {0x0f000840, 0x0FFF0800}, -/* Changed source for X-bar and MIPS clock to APLL */ - {0x0f000880, 0x000003DD}, + {0x0f000880, 0x000003DD}, /* Changed source for X-bar and MIPS clock to APLL */ {0x0f000860, 0x00000000}, -/* Changed source for X-bar and MIPS clock to APLL */ - {0x0F00a044, 0x1fffffff}, + {0x0F00a044, 0x1fffffff}, /* Changed source for X-bar and MIPS clock to APLL */ {0x0F00a040, 0x1f000000}, {0x0F00a084, 0x1Cffffff}, {0x0F00a080, 0x1C000000}, -/* # Enable 2 ports within X-bar */ - {0x0F00A000, 0x00000016}, -/* Memcontroller Default values */ - {0x0F007000, 0x00010001}, + {0x0F00A000, 0x00000016}, /* # Enable 2 ports within X-bar */ + {0x0F007000, 0x00010001}, /* Memcontroller Default values */ {0x0F007004, 0x01010100}, {0x0F007008, 0x01000001}, {0x0F00700c, 0x00000000},
@@ -240,10 +222,8 @@ static struct bcm_ddr_setting asT3B_DDRSetting133MHz[] = {/* # DPLL Clock Settin {0x0F00707C, 0x00000000}, {0x0F007080, 0x00000000}, {0x0F007084, 0x00000000}, -/* # Enable BW improvement within memory controller */ - {0x0F007094, 0x00000104}, -/* # Enable start bit within memory controller */ - {0x0F007018, 0x01010000}, + {0x0F007094, 0x00000104}, /* # Enable BW improvement within memory controller */ + {0x0F007018, 0x01010000}, /* # Enable start bit within memory controller */ };#define T3B_SKIP_CLOCK_PROGRAM_DUMP_80MHZ 9/*index for 0x0F007000 */
@@ -253,14 +233,12 @@ static struct bcm_ddr_setting asT3B_DDRSetting80MHz[] = {/* # DPLL Clock Setting {0x0f000840, 0x0FFF1F00}, {0x0f000880, 0x000003DD}, {0x0f000860, 0x00000000}, - {0x0F00a044, 0x1fffffff}, {0x0F00a040, 0x1f000000}, {0x0F00a084, 0x1Cffffff}, {0x0F00a080, 0x1C000000}, {0x0F00a000, 0x00000016}, -/* Memcontroller Default values */ - {0x0F007000, 0x00010001}, + {0x0F007000, 0x00010001}, /* Memcontroller Default values */ {0x0F007004, 0x01000000}, {0x0F007008, 0x01000001}, {0x0F00700c, 0x00000000},
@@ -295,10 +273,8 @@ static struct bcm_ddr_setting asT3B_DDRSetting80MHz[] = {/* # DPLL Clock Setting {0x0F007080, 0x00000000}, {0x0F007084, 0x00000000}, {0x0F007094, 0x00000104}, -/* # Enable start bit within memory controller */ - {0x0F007018, 0x01010000} + {0x0F007018, 0x01010000} /* # Enable start bit within memory controller */ }; -/* 100Mhz */ #define T3B_SKIP_CLOCK_PROGRAM_DUMP_100MHZ 9/* index for 0x0F007000 */ static struct bcm_ddr_setting asT3B_DDRSetting100MHz[] = {/* # DPLL Clock Setting */
@@ -311,10 +287,8 @@ static struct bcm_ddr_setting asT3B_DDRSetting100MHz[] = {/* # DPLL Clock Settin {0x0F00a040, 0x1f000000}, {0x0F00a084, 0x1Cffffff}, {0x0F00a080, 0x1C000000}, -/*# Enable 2 ports within X-bar */ - {0x0F00A000, 0x00000016}, -/* Memcontroller Default values */ - {0x0F007000, 0x00010001}, + {0x0F00A000, 0x00000016}, /*# Enable 2 ports within X-bar */ + {0x0F007000, 0x00010001}, /* Memcontroller Default values */ {0x0F007004, 0x01010100}, {0x0F007008, 0x01000001}, {0x0F00700c, 0x00000000},
@@ -348,28 +322,22 @@ static struct bcm_ddr_setting asT3B_DDRSetting100MHz[] = {/* # DPLL Clock Settin {0x0F00707C, 0x00000000}, {0x0F007080, 0x00000000}, {0x0F007084, 0x00000000}, -/* # Enable BW improvement within memory controller */ - {0x0F007094, 0x00000104}, -/* # Enable start bit within memory controller */ - {0x0F007018, 0x01010000} + {0x0F007094, 0x00000104}, /* # Enable BW improvement within memory controller */ + {0x0F007018, 0x01010000} /* # Enable start bit within memory controller */ }; - -#define T3LP_SKIP_CLOCK_PROGRAM_DUMP_133MHZ 9/*index for 0x0F007000 */ static struct bcm_ddr_setting asT3LP_DDRSetting133MHz[] = {/* # DPLL Clock Setting */ {0x0f000820 ,0x03F1365B }, {0x0f000810 ,0x00002F95 }, {0x0f000880 ,0x000003DD }, -/* Changed source for X-bar and MIPS clock to APLL */ - {0x0f000840 ,0x0FFF0000 }, + {0x0f000840 ,0x0FFF0000 },/* Changed source for X-bar and MIPS clock to APLL */ {0x0f000860 ,0x00000000 }, {0x0F00a044 ,0x1fffffff }, {0x0F00a040 ,0x1f000000 }, {0x0F00a084 ,0x1Cffffff }, {0x0F00a080 ,0x1C000000 }, {0x0F00A000 ,0x00000016 }, -/* Memcontroller Default values */ - {0x0F007000 ,0x00010001 }, + {0x0F007000 ,0x00010001 },/* Memcontroller Default values */ {0x0F007004 ,0x01010100 }, {0x0F007008 ,0x01000001 }, {0x0F00700c, 0x00000000},
@@ -406,15 +374,12 @@ static struct bcm_ddr_setting asT3LP_DDRSetting133MHz[] = {/* # DPLL Clock Setti {0x0F007088, 0x01000001}, {0x0F00708c, 0x00000101}, {0x0F007090, 0x00000000}, -/*# Enable BW improvement within memory controller */ - {0x0F007094, 0x00040000}, + {0x0F007094, 0x00040000}, /*# Enable BW improvement within memory controller */ {0x0F007098, 0x00000000}, {0x0F0070c8, 0x00000104},/* # Enable 2 ports within X-bar */ -/* # Enable start bit within memory controller */ - {0x0F007018, 0x01010000} + {0x0F007018, 0x01010000} /* # Enable start bit within memory controller */ }; -#define T3LP_SKIP_CLOCK_PROGRAM_DUMP_100MHZ 11/* index for 0x0F007000 */ static struct bcm_ddr_setting asT3LP_DDRSetting100MHz[] = {/* # DPLL Clock Setting */ {0x0f000810, 0x00002F95},
@@ -422,14 +387,12 @@ static struct bcm_ddr_setting asT3LP_DDRSetting100MHz[] = {/* # DPLL Clock Setti {0x0f000840, 0x0fff0000}, {0x0f000860, 0x00000000}, {0x0f000880, 0x000003DD}, -/* Changed source for X-bar and MIPS clock to APLL */ - {0x0f000840, 0x0FFF0000}, + {0x0f000840, 0x0FFF0000}, /* Changed source for X-bar and MIPS clock to APLL */ {0x0F00a044, 0x1fffffff}, {0x0F00a040, 0x1f000000}, {0x0F00a084, 0x1Cffffff}, {0x0F00a080, 0x1C000000}, -/* Memcontroller Default values */ - {0x0F007000, 0x00010001}, + {0x0F007000, 0x00010001}, /* Memcontroller Default values */ {0x0F007004, 0x01010100}, {0x0F007008, 0x01000001}, {0x0F00700c, 0x00000000},
@@ -469,12 +432,9 @@ static struct bcm_ddr_setting asT3LP_DDRSetting100MHz[] = {/* # DPLL Clock Setti {0x0F007094, 0x00010000}, {0x0F007098, 0x00000000}, {0x0F0070C8, 0x00000104}, -/* # Enable 2 ports within X-bar */ - {0x0F00A000, 0x00000016}, -/* # Enable start bit within memory controller */ - {0x0F007018, 0x01010000} + {0x0F00A000, 0x00000016}, /* # Enable 2 ports within X-bar */ + {0x0F007018, 0x01010000} /* # Enable start bit within memory controller */ }; -#define T3LP_SKIP_CLOCK_PROGRAM_DUMP_80MHZ 9/* index for 0x0F007000 */ static struct bcm_ddr_setting asT3LP_DDRSetting80MHz[] = {/* # DPLL Clock Setting */ {0x0f000820, 0x07F13FFF},
@@ -529,15 +489,9 @@ static struct bcm_ddr_setting asT3LP_DDRSetting80MHz[] = {/* # DPLL Clock Settin {0x0F0070C8, 0x00000104}, {0x0F007018, 0x01010000} }; - - - -/* T3 LP-B (UMA-B) */ -#define T3LPB_SKIP_CLOCK_PROGRAM_DUMP_160MHZ 7/* index for 0x0F007000 */ static struct bcm_ddr_setting asT3LPB_DDRSetting160MHz[] = {/* # DPLL Clock Setting */ - {0x0f000820 ,0x03F137DB }, {0x0f000810 ,0x01842795 }, {0x0f000860 ,0x00000000 },
@@ -591,15 +545,12 @@ static struct bcm_ddr_setting asT3LPB_DDRSetting160MHz[] = {/* # DPLL Clock Sett {0x0F0070C8, 0x00000104}, {0x0F007018, 0x01010000} }; - -#define T3LPB_SKIP_CLOCK_PROGRAM_DUMP_133MHZ 7/* index for 0x0F007000 */ static struct bcm_ddr_setting asT3LPB_DDRSetting133MHz[] = {/* # DPLL Clock Setting */ {0x0f000820 ,0x03F1365B }, {0x0f000810 ,0x00002F95 }, {0x0f000880 ,0x000003DD }, -/* Changed source for X-bar and MIPS clock to APLL */ - {0x0f000840 ,0x0FFF0000 }, + {0x0f000840 ,0x0FFF0000 },/* Changed source for X-bar and MIPS clock to APLL */ {0x0f000860 ,0x00000000 }, {0x0F00a044 ,0x1fffffff }, {0x0F00a040 ,0x1f000000 },
@@ -607,8 +558,7 @@ static struct bcm_ddr_setting asT3LPB_DDRSetting133MHz[] = {/* # DPLL Clock Sett {0x0F00a084, 0x1Cffffff},/* dump from here in internal memory */ {0x0F00a080, 0x1C000000}, {0x0F00A000, 0x00000016}, -/* Memcontroller Default values */ - {0x0F007000, 0x00010001}, + {0x0F007000, 0x00010001}, /* Memcontroller Default values */ {0x0F007004, 0x01010100}, {0x0F007008, 0x01000001}, {0x0F00700c, 0x00000000},
@@ -645,15 +595,12 @@ static struct bcm_ddr_setting asT3LPB_DDRSetting133MHz[] = {/* # DPLL Clock Sett {0x0F007088, 0x01000001}, {0x0F00708c, 0x00000101}, {0x0F007090, 0x00000000}, -/* # Enable BW improvement within memory controller */ - {0x0F007094, 0x00040000}, + {0x0F007094, 0x00040000}, /* # Enable BW improvement within memory controller */ {0x0F007098, 0x00000000}, {0x0F0070c8, 0x00000104},/* # Enable 2 ports within X-bar */ -/* # Enable start bit within memory controller */ - {0x0F007018, 0x01010000} + {0x0F007018, 0x01010000} /* # Enable start bit within memory controller */ }; -#define T3LPB_SKIP_CLOCK_PROGRAM_DUMP_100MHZ 8/*index for 0x0F007000 */ static struct bcm_ddr_setting asT3LPB_DDRSetting100MHz[] = {/* # DPLL Clock Setting */ {0x0f000810, 0x00002F95},
@@ -661,15 +608,13 @@ static struct bcm_ddr_setting asT3LPB_DDRSetting100MHz[] = {/* # DPLL Clock Sett {0x0f000840, 0x0fff0000}, {0x0f000860, 0x00000000}, {0x0f000880, 0x000003DD}, -/* Changed source for X-bar and MIPS clock to APLL */ - {0x0f000840, 0x0FFF0000}, + {0x0f000840, 0x0FFF0000}, /* Changed source for X-bar and MIPS clock to APLL */ {0x0F00a044, 0x1fffffff}, {0x0F00a040, 0x1f000000}, {0x0f003050, 0x00000021},/* flash/eeprom clock divisor which set the flash clock to 20 MHz */ {0x0F00a084, 0x1Cffffff}, /* dump from here in internal memory */ {0x0F00a080, 0x1C000000}, -/* Memcontroller Default values */ - {0x0F007000, 0x00010001}, + {0x0F007000, 0x00010001}, /* Memcontroller Default values */ {0x0F007004, 0x01010100}, {0x0F007008, 0x01000001}, {0x0F00700c, 0x00000000},
@@ -709,12 +654,9 @@ static struct bcm_ddr_setting asT3LPB_DDRSetting100MHz[] = {/* # DPLL Clock Sett {0x0F007094, 0x00010000}, {0x0F007098, 0x00000000}, {0x0F0070C8, 0x00000104}, -/* # Enable 2 ports within X-bar */ - {0x0F00A000, 0x00000016}, -/* # Enable start bit within memory controller */ - {0x0F007018, 0x01010000} + {0x0F00A000, 0x00000016}, /* # Enable 2 ports within X-bar */ + {0x0F007018, 0x01010000} /* # Enable start bit within memory controller */ }; -#define T3LPB_SKIP_CLOCK_PROGRAM_DUMP_80MHZ 7/*index for 0x0F007000 */ static struct bcm_ddr_setting asT3LPB_DDRSetting80MHz[] = {/* # DPLL Clock Setting */ {0x0f000820, 0x07F13FFF},
@@ -771,7 +713,6 @@ static struct bcm_ddr_setting asT3LPB_DDRSetting80MHz[] = {/* # DPLL Clock Setti {0x0F007018, 0x01010000} }; -int ddr_init (struct bcm_mini_adapter *Adapter) {struct bcm_ddr_setting *psDDRSetting =NULL ;
@@ -806,7 +747,6 @@ int ddr_init(struct bcm_mini_adapter *Adapter)default :return -EINVAL ; } -break ;case T3LPB :case BCS220_2 :
@@ -832,9 +772,6 @@ int ddr_init(struct bcm_mini_adapter *Adapter) } }switch (Adapter->DDRSetting) { - - -case DDR_80_MHZ : psDDRSetting = asT3LPB_DDRSetting80MHz; RegCount = (sizeof(asT3B_DDRSetting80MHz)/
@@ -849,24 +786,20 @@ int ddr_init(struct bcm_mini_adapter *Adapter) psDDRSetting = asT3LPB_DDRSetting133MHz; RegCount = (sizeof (asT3B_DDRSetting133MHz)/sizeof (struct bcm_ddr_setting )); -if (Adapter->bMipsConfig ==MIPS_200_MHZ ) uiClockSetting =0x03F13652 ;else uiClockSetting =0x03F1365B ;break ; -case DDR_160_MHZ : psDDRSetting = asT3LPB_DDRSetting160MHz; RegCount =sizeof (asT3LPB_DDRSetting160MHz)/sizeof (struct bcm_ddr_setting ); -if (Adapter->bMipsConfig ==MIPS_200_MHZ ) uiClockSetting =0x03F137D2 ;else uiClockSetting =0x03F137DB ; }break ; -case 0xbece0110 :case 0xbece0120 :case 0xbece0121 :
@@ -906,7 +839,6 @@ int ddr_init(struct bcm_mini_adapter *Adapter) sizeof(struct bcm_ddr_setting));break ;case DDR_133_MHZ : -if (Adapter->bDPLLConfig ==PLL_266_MHZ ) {/*266Mhz PLL selected. */ memcpy (asT3B_DDRSetting133MHz, asDPLL_266MHZ,sizeof (asDPLL_266MHZ));
@@ -927,7 +859,6 @@ int ddr_init(struct bcm_mini_adapter *Adapter)return -EINVAL ; }break ; - }default :return -EINVAL ;
@@ -949,7 +880,6 @@ int ddr_init(struct bcm_mini_adapter *Adapter) RegCount--; psDDRSetting++; } -if (Adapter->chip_id >=0xbece3300 ) {mdelay (3 ); if ((Adapter->chip_id != BCS220_2) &&
@@ -982,7 +912,6 @@ int ddr_init(struct bcm_mini_adapter *Adapter) } }mdelay (3 ); -/* DC/DC standby change... * This is to be done only for Hybrid PMU mode. * with the current h/w there is no way to detect this.
@@ -1023,7 +952,6 @@ int ddr_init(struct bcm_mini_adapter *Adapter)return retval; } }else if (Adapter->PmuMode ==HYBRID_MODE_6 ) { - retval =rdmalt (Adapter, (UINT )0x0f000c00 , &uiResetValue,sizeof (uiResetValue));if (retval <0 ) {BCM_DEBUG_PRINT (Adapter,CMHOST ,RDM ,DBG_LVL_ALL ,"%s:%d RDM failed\n" , __func__, __LINE__);
@@ -1098,7 +1026,6 @@ int download_ddr_settings(struct bcm_mini_adapter *Adapter)return -EINVAL ; }break ; -case T3LPB :case BCS220_2 :case BCS220_2BC :
@@ -1124,7 +1051,6 @@ int download_ddr_settings(struct bcm_mini_adapter *Adapter) RegCount -=T3LPB_SKIP_CLOCK_PROGRAM_DUMP_133MHZ ; psDDRSetting +=T3LPB_SKIP_CLOCK_PROGRAM_DUMP_133MHZ ;break ; -case DDR_160_MHZ : bOverrideSelfRefresh = TRUE; psDDRSetting = asT3LPB_DDRSetting160MHz;
@@ -1194,7 +1120,6 @@ int download_ddr_settings(struct bcm_mini_adapter *Adapter) retval =wrmalt (Adapter, ul_ddr_setting_load_addr, &value,sizeof (value));if (retval) {BCM_DEBUG_PRINT (Adapter,DBG_TYPE_PRINTK ,0 ,0 ,"%s:%d\n" , __func__, __LINE__); -return retval; } ul_ddr_setting_load_addr +=sizeof (ULONG );
@@ -1208,7 +1133,6 @@ int download_ddr_settings(struct bcm_mini_adapter *Adapter) ul_ddr_setting_load_addr +=sizeof (ULONG ); RegCount *= (sizeof (struct bcm_ddr_setting )/sizeof (ULONG )); -while (RegCount && !retval) { value = psDDRSetting->ulRegAddress ; retval =wrmalt (Adapter, ul_ddr_setting_load_addr, &value,sizeof (value));
@@ -1223,7 +1147,6 @@ int download_ddr_settings(struct bcm_mini_adapter *Adapter) } }else { value = psDDRSetting->ulRegValue; -if (STATUS_SUCCESS !=wrmalt (Adapter, ul_ddr_setting_load_addr , &value,sizeof (value))) {BCM_DEBUG_PRINT (Adapter,DBG_TYPE_PRINTK ,0 ,0 ,"%s:%d\n" , __func__, __LINE__);
Signature · 1 line
1.8.4