tools: mxsboot: Implement SPI SMEM block support
PATCH 1/1 tools: mxsboot: Implement SPI SMEM block support
This patch adds support for augmenting the BootStream with the SMEM block. For further details on the SMEM block, please refer to i.MX28 datasheet section 12.10 .
NOTE: It is absolutely optional to augment BootStream with SMEM
block. The SMEM block is only useful if you need to tweak SPI NOR clockspeed or place the u-boot.sb elsewhere than at block 1 of the SPI NOR (SMEM block resides in block 0). The i.MX28 will boot BootStream image placed at block 0 in SPI NOR directly.
Signed-off-by Marek Vasut <[email protected]>
Cc Stefano Babic <[email protected]>
--- tools/mxsboot.c | 133 ++++++++++++++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 130 insertions(+), 3 deletions(-)
tools/mxsboot.c +130 -3
@@ -38,6 +38,14 @@ static uint32_t nand_erasesize = 128 * 1024;static uint32_t sd_sector =2048 ;/* +* Layout for the SPI configuration block with the default settings +* in it. This is what the BootROM uses. +*/ +static uint32_t spi_sector_size =128 ; +static uint32_t spi_image_offset =64 *1024 ;/* Block 1 */ +static uint32_t spi_clock_idx =8 ;/* BootROM's default clock */ + +/* * Each of the U-Boot bootstreams is at maximum 1MB big. * * TWEAK this if, for some wild reason, you need to boot bigger image.
@@ -125,6 +133,49 @@ struct mx28_sd_config_block {struct mx28_sd_drive_info drv_info[1 ]; }; +#define SSP_CLOCK_CONFIG_CLKSEL (n) ((n) << 0) +#define SSP_CLOCK_CONFIG_IO_FRAC (n) ((n) << 1) +#define SSP_CLOCK_CONFIG_SSP_FRAC (n) ((n) << 7) +#define SSP_CLOCK_CONFIG_SSP_DIV (n) ((n) << 16) +#define SSP_CLOCK_CONFIG_SSP_RATE (n) ((n) << 24) +#define SSP_CLOCK_CONFIG (clksel, iofrac, sspfrac, sspdiv, ssprate) \ + SSP_CLOCK_CONFIG_CLKSEL(clksel) | \ + SSP_CLOCK_CONFIG_IO_FRAC(iofrac) | \ + SSP_CLOCK_CONFIG_SSP_FRAC(sspfrac) | \ + SSP_CLOCK_CONFIG_SSP_DIV(sspdiv) | \ + SSP_CLOCK_CONFIG_SSP_RATE(ssprate) + +#define SSP_BOOT_FLAG_DISABLE_FASTREAD (1 << 0) + +struct mx28_spi_config_block { +uint32_t signature; +uint32_t boot_start_addr; +uint32_t sector_size; +uint32_t flags; +uint32_t clock_config_size; +uint32_t clock_config; +}; + +/* This is aligned with Table 12-27 in i.MX28 reference manual. */ +static const uint32_t mx28_spi_clock_config[] = { +0x00000000 ,/* 0 ... invalid. */ +SSP_CLOCK_CONFIG (1 ,0 ,0 ,100 ,0 ),/* 1 ... 0.24 MHz */ +SSP_CLOCK_CONFIG (1 ,0 ,0 ,24 ,0 ),/* 2 ... 1 MHz */ +SSP_CLOCK_CONFIG (1 ,0 ,0 ,12 ,0 ),/* 3 ... 2 MHz */ +SSP_CLOCK_CONFIG (1 ,0 ,0 ,6 ,0 ),/* 4 ... 4 MHz */ +SSP_CLOCK_CONFIG (1 ,0 ,0 ,4 ,0 ),/* 5 ... 6 MHz */ +SSP_CLOCK_CONFIG (0 ,18 ,6 ,10 ,0 ),/* 6 ... 8 MHz */ +SSP_CLOCK_CONFIG (0 ,18 ,6 ,8 ,0 ),/* 7 ... 10 MHz */ +SSP_CLOCK_CONFIG (1 ,0 ,0 ,2 ,0 ),/* 8 ... 12 MHz */ +SSP_CLOCK_CONFIG (0 ,18 ,5 ,6 ,0 ),/* 9 ... 16 MHz */ +SSP_CLOCK_CONFIG (0 ,18 ,6 ,4 ,0 ),/* 10 .. 20 MHz */ +SSP_CLOCK_CONFIG (0 ,18 ,8 ,2 ,0 ),/* 11 .. 30 MHz */ +SSP_CLOCK_CONFIG (0 ,18 ,6 ,2 ,0 ),/* 12 .. 40 MHz */ +SSP_CLOCK_CONFIG (0 ,18 ,5 ,2 ,0 ),/* 13 .. 48 MHz */ +SSP_CLOCK_CONFIG (0 ,21 ,4 ,2 ,0 ),/* 14 .. 51.4 MHz */ +0x00000000 /* 15 .. invalid. */ +}; +static inline uint32_t mx28_nand_ecc_size_in_bits (uint32_t ecc_strength) {return ecc_strength *13 ;
@@ -445,6 +496,7 @@ static void usage(void)" <type> type of image:\n" " \"nand\" for NAND image\n" " \"sd\" for SD image\n" +" \"spi\" for SPI NOR image\n" " <infile> input file, the u-boot.sb bootstream\n" " <outfile> output file, the bootable image\n" "\n");
@@ -456,6 +508,11 @@ static void usage(void)"\n" "For SD boot, these options are accepted:\n" " -p <sector> Sector where the SGTL partition starts\n" +"\n" +"For SPI NOR boot, these options are accepted:\n" +" -s <size> SPI NOR sector size\n" +" -i <size> SPI NOR image offset (multiple of page size)\n" +" -c <size> Clock INDEX (see Table 12-27 in MX28 RM)\n" ); }
@@ -577,6 +634,54 @@ err0:return ret; } +static int mx28_create_spi_image (int infd,int outfd) +{ +int ret =-1 ; +uint32_t *buf; +int size; +off_t fsize; +ssize_t wr_size; +struct mx28_spi_config_block *cb; + + fsize =lseek (infd,0 ,SEEK_END ); +lseek (infd,0 ,SEEK_SET ); + size = fsize + spi_image_offset; + + buf =malloc (size); +if (!buf) { +printf ("Can not allocate output buffer of %d bytes\n" , size); + goto err0; + } + + ret =read (infd, (uint8_t *)buf + spi_image_offset, fsize); +if (ret != fsize) { + ret =-1 ; + goto err1; + } + + cb = (struct mx28_spi_config_block *)buf; + + cb->signature =0x4d454d53 ; + cb->boot_start_addr = spi_image_offset; + cb->sector_size = spi_sector_size; + cb->flags =0x0 ; + cb->clock_config_size =sizeof (cb->clock_config); + cb->clock_config = mx28_spi_clock_config[spi_clock_idx]; + + wr_size =write (outfd, buf, size); +if (wr_size != size) { + ret =-1 ; + goto err1; + } + + ret =0 ; + +err1: +free (buf); +err0: +return ret; +} +static int parse_ops (int argc,char **argv) {int i;
@@ -588,7 +693,10 @@ static int parse_ops(int argc, char **argv)PARAM_ERASE ,PARAM_PART ,PARAM_SD , - PARAM_NAND +PARAM_NAND , +PARAM_SPI_SECT_SIZE , +PARAM_SPI_IMAGE_OFFSET , + PARAM_SPI_CLOCK_IDX };int type;
@@ -596,15 +704,24 @@ static int parse_ops(int argc, char **argv)return -1 ;for (i =1 ; i < argc; i++) { +/* NAND */ if (!strncmp (argv[i],"-w" ,2 )) type =PARAM_WRITE ;else if (!strncmp (argv[i],"-o" ,2 )) type =PARAM_OOB ;else if (!strncmp (argv[i],"-e" ,2 )) type =PARAM_ERASE ; +/* SD/MMC */ else if (!strncmp (argv[i],"-p" ,2 )) type =PARAM_PART ; -else /* SD/MMC */ +/* SPI */ +else if (!strncmp (argv[i],"-s" ,2 )) + type =PARAM_SPI_SECT_SIZE ; +else if (!strncmp (argv[i],"-i" ,2 )) + type =PARAM_SPI_IMAGE_OFFSET ; +else if (!strncmp (argv[i],"-c" ,2 )) + type =PARAM_SPI_CLOCK_IDX ; +else break ; tmp =strtol (argv[++i], &end,10 );
@@ -621,9 +738,17 @@ static int parse_ops(int argc, char **argv) nand_erasesize = tmp;if (type ==PARAM_PART ) sd_sector = tmp; + +if (type ==PARAM_SPI_SECT_SIZE ) + spi_sector_size = tmp; +if (type ==PARAM_SPI_IMAGE_OFFSET ) + spi_image_offset = tmp; +if (type ==PARAM_SPI_CLOCK_IDX ) + spi_clock_idx = tmp; } -if (strcmp (argv[i],"sd" ) &&strcmp (argv[i],"nand" )) +if (strcmp (argv[i],"sd" ) &&strcmp (argv[i],"nand" ) && +strcmp (argv[i],"spi" ))return -1 ;if (i +3 != argc)
@@ -664,6 +789,8 @@ int main(int argc, char **argv) ret =mx28_create_sd_image (infd, outfd); else if (!strcmp(argv[offset], "nand")) ret =mx28_create_nand_image (infd, outfd); + else if (!strcmp(argv[offset], "spi")) + ret =mx28_create_spi_image (infd, outfd);close (outfd); err2:
Signature · 1 line
1.8.5.3