Skip to contentSkip to conversation

batctl: add option for multiif orig table

PATCH In review Simon Wunderlich 2 participants 3 messages Feb 18, 2014 – Feb 19, 2014

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 batctl: add option for multiif orig table

From: Simon Wunderlich <[email protected]>

---
 debug.c |   28 ++++++++++++++++++++++------
 1 file changed, 22 insertions(+), 6 deletions(-)
debug.c +22 -6
index d57324d..78c6e55 100644
@@ -89,8 +89,10 @@ static void debug_table_usage(int debug_table)
 	fprintf(stderr, " \t -H don't show the header\n");
 	fprintf(stderr, " \t -w [interval] watch mode - refresh the table continuously\n");
 
-	if (debug_table == BATCTL_TABLE_ORIGINATORS)
+	if (debug_table == BATCTL_TABLE_ORIGINATORS) {
 		fprintf(stderr, " \t -t timeout interval - don't print originators not seen for x.y seconds \n");
+		fprintf(stderr, " \t -i [interface] - show multiif originator table for a specific interface\n");
+	}
 }
 
 int handle_debug_table(char *mesh_iface, int debug_table, int argc, char **argv)
@@ -98,11 +100,12 @@ int handle_debug_table(char *mesh_iface, int debug_table, int argc, char **argv)
 	int optchar, read_opt = USE_BAT_HOSTS;
 	char full_path[MAX_PATH+1];
 	char *debugfs_mnt;
+	char *orig_iface = NULL;
 	float orig_timeout;
 	float watch_interval = 1;
 	opterr = 0;
 
-	while ((optchar = getopt(argc, argv, "hnw:t:H")) != -1) {
+	while ((optchar = getopt(argc, argv, "hnw:t:Hi:")) != -1) {
 		switch (optchar) {
 		case 'h':
 			debug_table_usage(debug_table);
@@ -138,11 +141,21 @@ int handle_debug_table(char *mesh_iface, int debug_table, int argc, char **argv)
 		case 'H':
 			read_opt |= SKIP_HEADER;
 			break;
+		case 'i':
+			if (debug_table != BATCTL_TABLE_ORIGINATORS) {
+				fprintf(stderr, "Error - unrecognised option '-%c'\n", optchar);
+				debug_table_usage(debug_table);
+				return EXIT_FAILURE;
+			}
+
+			orig_iface = optarg;
+			break;
 		case '?':
-			if (optopt == 't')
+			if (optopt == 't') {
 				fprintf(stderr, "Error - option '-t' needs a number as argument\n");
-
-			else if (optopt == 'w') {
+			} else if (optopt == 'i') {
+				fprintf(stderr, "Error - option '-i' needs an interface as argument\n");
+			} else if (optopt == 'w') {
 				read_opt |= CLR_CONT_READ;
 				break;
 			}
@@ -162,7 +175,10 @@ int handle_debug_table(char *mesh_iface, int debug_table, int argc, char **argv)
 		return EXIT_FAILURE;
 	}
 
-	debugfs_make_path(DEBUG_BATIF_PATH_FMT "/", mesh_iface, full_path, sizeof(full_path));
+	if (orig_iface)
+		debugfs_make_path(DEBUG_BATIF_PATH_FMT "/", orig_iface, full_path, sizeof(full_path));
+	else
+		debugfs_make_path(DEBUG_BATIF_PATH_FMT "/", mesh_iface, full_path, sizeof(full_path));
 	return read_file(full_path, (char *)batctl_debug_tables[debug_table].debugfs_name,
 			 read_opt, orig_timeout, watch_interval,
 			 batctl_debug_tables[debug_table].header_lines);
Signature · 1 line
1.7.10.4
#1 lore raw
Quoted 12 lines · On Tuesday 18 February 2014 15:13:24 Simon Wunderlich wrote:
(quoted diff) +1 -1
@@ -162,7 +175,10 @@ int handle_debug_table(char *mesh_iface, int
 debug_table, int argc, char **argv) return EXIT_FAILURE;
        }
 
-       debugfs_make_path(DEBUG_BATIF_PATH_FMT "/", mesh_iface, full_path,
 sizeof(full_path)); +       if (orig_iface)
+               debugfs_make_path(DEBUG_BATIF_PATH_FMT "/", orig_iface,

full_path, sizeof(full_path)); + else
+ debugfs_make_path(DEBUG_BATIF_PATH_FMT "/", mesh_iface,
full_path, sizeof(full_path)); return read_file(full_path, (char *)batctl_debug_tables[debug_table].debugfs_name, read_opt, orig_timeout, watch_interval,

Quoted 1 line
                         batctl_debug_tables[debug_table].header_lines);

While playing with your patch I noticed a couple of things:

* 'batctl originators -i eth0' is equivalent to 'batctl -m eth0 originators'
* the latter works even without your patch
* the orig table output does not say which interface we are looking at but
always reports: (bat0 BATMAN_IV)
* /sys/kernel/debug/batman_adv/ contains all sorts of hard-interfaces on my
test setup even if they are not used by batman-adv - is the intended ?

Cheers,
Marek

#2 lore raw
Quoted 15 lines · On Tuesday 18 February 2014 15:13:24 Simon Wunderlich wrote:
Quoted 14 lines
(quoted diff) +1 -1
@@ -162,7 +175,10 @@ int handle_debug_table(char *mesh_iface, int
 debug_table, int argc, char **argv) return EXIT_FAILURE;
 
        }
 
-       debugfs_make_path(DEBUG_BATIF_PATH_FMT "/", mesh_iface,
 full_path, sizeof(full_path)); +       if (orig_iface)
+               debugfs_make_path(DEBUG_BATIF_PATH_FMT "/", orig_iface,

full_path, sizeof(full_path)); + else
+ debugfs_make_path(DEBUG_BATIF_PATH_FMT "/", mesh_iface,
full_path, sizeof(full_path)); return read_file(full_path, (char *)batctl_debug_tables[debug_table].debugfs_name, read_opt, orig_timeout, watch_interval,

Quoted 7 lines
Quoted 1 line
                         batctl_debug_tables[debug_table].header_lines);

While playing with your patch I noticed a couple of things:

* 'batctl originators -i eth0' is equivalent to 'batctl -m eth0
originators'
* the latter works even without your patch

Both is true, because the originators file is at the same position (eth0/originators instead of bat0/originators).

Quoted 2 lines

* the orig table output does not say which interface we are looking at but
always reports: (bat0 BATMAN_IV)

Yes, check the whole first line:
bat0/originators: [B.A.T.M.A.N. adv master-b82b9b2, MainIF/MAC:
eth0/fe:f0:00:00:02:01 (bat0 BATMAN_IV)] eth0/originators: [B.A.T.M.A.N. adv master-b82b9b2, IF/MAC:
eth0/fe:f0:00:00:02:01 (bat0 BATMAN_IV)] eth1/originators: [B.A.T.M.A.N. adv master-b82b9b2, IF/MAC:
eth1/fe:f1:00:00:02:01 (bat0 BATMAN_IV)]

Quoted 2 lines

* /sys/kernel/debug/batman_adv/ contains all sorts of hard-interfaces on
my test setup even if they are not used by batman-adv - is the intended ?

Yes. Like the for the sysfs, a folder is created for every interface even if not used - creating/removing on the fly would bring us a lot of locking fun which I wanted to avoid (I think we have discussed that when the batman-adv patches came in).

Cheers,
Simon