Skip to contentSkip to conversation

Ethernet persistence

U-Boot Anthony Mahar 4 participants 5 messages Feb 27, 2014 – Feb 28, 2014

lore
Share & tools
lore
#0 lore raw

How can I make the ethernet connection persistent (after first use), rather than reconnecting/re initializing on each reuse?

I'm working with a Xilinx Zynq zc706 board and am up and running u-boot quite successfully. My main use case is to store u-boot in on-board flash, and have u-boot tftp get / boot the bitstream, kernel image, devicetree, and ramdisk image. The following script functions well:

	"qspiboot=echo Configure PL and booting Linux from TFTP... && " \
		"fpga info 0;"						    \
		"tftp 0x1000000 system.bin;"				    \
		"fpga load 0 0x1000000 cb44bc;" \
		"tftp 0x3000000 ${kernel_image};" \
		"tftp 0x2A00000 ${devicetree_image};" \
		"tftp 0x2000000 ${ramdisk_image};" \
		"bootm 0x3000000 0x2000000 0x2A00000\0" \

The ethernet (Zynq's gem.e000b000) will get initialized on first use, as appropriate, however the Ethernet is reinitialized and auto negotiated again for each subsequent tftp request which shouldn't be necessary. A snippet is listed below. Each 'reconnection' takes several seconds... a few to auto negotiate, then a few more for the Windows based TFTP server to recognize the connection and allow connections to the server. Multiply this by the number of transfers and it takes a very long time to transfer a very little amount of data.

Snippet:

Xilinx Device
Descriptor @ 0x3ffbaf78

Family:         Zynq PL
Interface type: Device configuration interface (Zynq)
Device Size:    13321404 bytes
Cookie:         0x45 (69)
Device name:    7z045

No Device Function Table.
Gem.e000b000 Waiting for PHY auto negotiation to complete....... done Using Gem.e000b000 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.10 Filename 'system.bin'.
Load address: 0x1000000
Loading: T #################################################################

         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ###############################################################
         953.1 KiB/s

done
Bytes transferred = 13321404 (cb44bc hex)
Gem.e000b000:7 is connected to Gem.e000b000. Reconnecting to Gem.e000b000 Gem.e000b000 Waiting for PHY auto negotiation to complete....... done Using Gem.e000b000 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.10 Filename 'uImage'.
Load address: 0x3000000
Loading: T #################################################################

         #################################################################
         #################################################################
         ################
         429.7 KiB/s

done

--
View this message in context: http://u-boot.10912.n7.nabble.com/Ethernet-persistence-tp174934.html
Sent from the U-Boot mailing list archive at Nabble.com.

#1 lore raw
Quoted 65 lines · Anthony Mahar

How can I make the ethernet connection persistent (after first use), rather than reconnecting/re initializing on each reuse?

I'm working with a Xilinx Zynq zc706 board and am up and running u-boot quite successfully. My main use case is to store u-boot in on-board flash, and have u-boot tftp get / boot the bitstream, kernel image, devicetree, and ramdisk image. The following script functions well:

	"qspiboot=echo Configure PL and booting Linux from TFTP... && " \
		"fpga info 0;"						    \
		"tftp 0x1000000 system.bin;"				    \
		"fpga load 0 0x1000000 cb44bc;" \
		"tftp 0x3000000 ${kernel_image};" \
		"tftp 0x2A00000 ${devicetree_image};" \
		"tftp 0x2000000 ${ramdisk_image};" \
		"bootm 0x3000000 0x2000000 0x2A00000\0" \

The ethernet (Zynq's gem.e000b000) will get initialized on first use, as appropriate, however the Ethernet is reinitialized and auto negotiated again for each subsequent tftp request which shouldn't be necessary. A snippet is listed below. Each 'reconnection' takes several seconds... a few to auto negotiate, then a few more for the Windows based TFTP server to recognize the connection and allow connections to the server. Multiply this by the number of transfers and it takes a very long time to transfer a very little amount of data.

Snippet:

Xilinx Device
Descriptor @ 0x3ffbaf78

Family:         Zynq PL
Interface type: Device configuration interface (Zynq)
Device Size:    13321404 bytes
Cookie:         0x45 (69)
Device name:    7z045

No Device Function Table.
Gem.e000b000 Waiting for PHY auto negotiation to complete....... done Using Gem.e000b000 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.10 Filename 'system.bin'.
Load address: 0x1000000
Loading: T #################################################################

         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ###############################################################
         953.1 KiB/s

done
Bytes transferred = 13321404 (cb44bc hex)
Gem.e000b000:7 is connected to Gem.e000b000. Reconnecting to Gem.e000b000 Gem.e000b000 Waiting for PHY auto negotiation to complete....... done Using Gem.e000b000 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.10 Filename 'uImage'.
Load address: 0x3000000
Loading: T #################################################################

Quoted 6 lines
         #################################################################
         #################################################################
         ################
         429.7 KiB/s

done

I am not sure if this is intention with phylib but this was bring up with phylib. I still support non-phylib version in xilinx u-boot git version (but it is not regularly tested).

Not sure what your system.bin is but if you use FIT then you can just download one image.

Thanks
Michal

Signature · 14 lines
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/
Maintainer of Linux kernel - Xilinx Zynq ARM architecture
Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform


-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 263 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20140228/8eb09d47/attachment.pgp>
#2 lore raw
In reply to Anthony Mahar

Hi Anthony,

Quoted 20 lines · Anthony Mahar

How can I make the ethernet connection persistent (after first use), rather than reconnecting/re initializing on each reuse?

I'm working with a Xilinx Zynq zc706 board and am up and running u-boot quite successfully. My main use case is to store u-boot in on-board flash, and have u-boot tftp get / boot the bitstream, kernel image, devicetree, and
ramdisk image. The following script functions well:

        "qspiboot=echo Configure PL and booting Linux from TFTP... && " \
                "fpga info 0;"
 \
                "tftp 0x1000000 system.bin;"
 \
                "fpga load 0 0x1000000 cb44bc;" \
                "tftp 0x3000000 ${kernel_image};" \
                "tftp 0x2A00000 ${devicetree_image};" \
                "tftp 0x2000000 ${ramdisk_image};" \
                "bootm 0x3000000 0x2000000 0x2A00000\0" \
Quoted 11 lines

The ethernet (Zynq's gem.e000b000) will get initialized on first use, as appropriate, however the Ethernet is reinitialized and auto negotiated again
for each subsequent tftp request which shouldn't be necessary. A snippet is
listed below. Each 'reconnection' takes several seconds... a few to auto negotiate, then a few more for the Windows based TFTP server to recognize the connection and allow connections to the server. Multiply this by the number of transfers and it takes a very long time to transfer a very little amount of data.

Yes as Michal says you should use FIT and put everything in one file, or less than 4. I'm not sure if we have a command to load your FPGA image from FIT though. We could add one fairly easily now that we have fit_image_load().

Also take a look at asix_init() in drivers/usb/eth, which does not re-init the link if it is already up. This speeds things up.

Regards,
Simon

#3 lore raw

Hi Simon,

Quoted 36 lines · Simon Glass

Hi Anthony,

Quoted 20 lines · Anthony Mahar

How can I make the ethernet connection persistent (after first use), rather than reconnecting/re initializing on each reuse?

I'm working with a Xilinx Zynq zc706 board and am up and running u-boot quite successfully. My main use case is to store u-boot in on-board flash, and have u-boot tftp get / boot the bitstream, kernel image, devicetree, and
ramdisk image. The following script functions well:

        "qspiboot=echo Configure PL and booting Linux from TFTP... && " \
                "fpga info 0;"
 \
                "tftp 0x1000000 system.bin;"
 \
                "fpga load 0 0x1000000 cb44bc;" \
                "tftp 0x3000000 ${kernel_image};" \
                "tftp 0x2A00000 ${devicetree_image};" \
                "tftp 0x2000000 ${ramdisk_image};" \
                "bootm 0x3000000 0x2000000 0x2A00000\0" \
Quoted 11 lines

The ethernet (Zynq's gem.e000b000) will get initialized on first use, as appropriate, however the Ethernet is reinitialized and auto negotiated again
for each subsequent tftp request which shouldn't be necessary. A snippet is
listed below. Each 'reconnection' takes several seconds... a few to auto negotiate, then a few more for the Windows based TFTP server to recognize the connection and allow connections to the server. Multiply this by the number of transfers and it takes a very long time to transfer a very little amount of data.

Quoted 4 lines

Yes as Michal says you should use FIT and put everything in one file, or less than 4. I'm not sure if we have a command to load your FPGA image from FIT though. We could add one fairly easily now that we have fit_image_load().

I have this on my todo list and definitely I would love to extend FIT image with adding FPGA to it.

Thanks,
Michal

Signature · 14 lines
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/
Maintainer of Linux kernel - Xilinx Zynq ARM architecture
Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform


-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 263 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20140228/51b7ebfd/attachment.pgp>
#4 lore raw
In reply to Simon Glass
Quoted 36 lines · Simon Glass

Hi Anthony,

Quoted 20 lines · Anthony Mahar

How can I make the ethernet connection persistent (after first use), rather than reconnecting/re initializing on each reuse?

I'm working with a Xilinx Zynq zc706 board and am up and running u-boot quite successfully. My main use case is to store u-boot in on-board flash, and have u-boot tftp get / boot the bitstream, kernel image, devicetree, and
ramdisk image. The following script functions well:

        "qspiboot=echo Configure PL and booting Linux from TFTP... && " \
                "fpga info 0;"
 \
                "tftp 0x1000000 system.bin;"
 \
                "fpga load 0 0x1000000 cb44bc;" \
                "tftp 0x3000000 ${kernel_image};" \
                "tftp 0x2A00000 ${devicetree_image};" \
                "tftp 0x2000000 ${ramdisk_image};" \
                "bootm 0x3000000 0x2000000 0x2A00000\0" \
Quoted 11 lines

The ethernet (Zynq's gem.e000b000) will get initialized on first use, as appropriate, however the Ethernet is reinitialized and auto negotiated again
for each subsequent tftp request which shouldn't be necessary. A snippet is
listed below. Each 'reconnection' takes several seconds... a few to auto negotiate, then a few more for the Windows based TFTP server to recognize the connection and allow connections to the server. Multiply this by the number of transfers and it takes a very long time to transfer a very little amount of data.

Quoted 4 lines

Yes as Michal says you should use FIT and put everything in one file, or less than 4. I'm not sure if we have a command to load your FPGA image from FIT though. We could add one fairly easily now that we have fit_image_load().

FIT is not particularly convenient when repeatedly updating a single component, and requires more work to assemble. I thought it was meant to replace old-style multi-image, not to deprecate individual images.

Quoted 2 lines

Also take a look at asix_init() in drivers/usb/eth, which does not re-init the link if it is already up. This speeds things up.

So the question is why other ethernet drivers don't do this...

-Scott