w1: mxc_w1: Fix incorrect "presence" status
Subsystems (2)
PATCH 1/4 w1: mxc_w1: Fix incorrect "presence" status
W1 reset_bus() should return zero if slave device is present. This patch fix this issue.
---
Please apply this patch to current -rc if it possible.
--- drivers/w1/masters/mxc_w1.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/w1/masters/mxc_w1.c +1 -1
@@ -66,7 +66,7 @@ static u8 mxc_w1_ds2_reset_bus(void *data)udelay (100 ); } -return !!(reg_val &MXC_W1_CONTROL_PST ); +return !(reg_val &MXC_W1_CONTROL_PST ); }/*
Signature · 1 line
1.8.3.2
PATCH 2/4 w1: mxc_w1: Optimize mxc_w1_ds2_reset_bus()
According to the i.MX reference manual, the reset procedure and "presence" pulse takes 511 and 512 us, respectively. Measurement for i.MX27 is about 1100 us. There is no need to wait Reset+Presence more than this time.
This patch optimizes mxc_w1_ds2_reset_bus() function to use proper value for delay after w1 bus reset. Nevertheless, a small margin for the timeout has been added for the case if clock frequency is inaccurate.
--- drivers/w1/masters/mxc_w1.c | 32 +++++++++++++++----------------- 1 file changed, 15 insertions(+), 17 deletions(-)
drivers/w1/masters/mxc_w1.c +15 -17
@@ -15,16 +15,13 @@#include <linux/clk.h> #include <linux/delay.h> #include <linux/io.h> +#include <linux/jiffies.h> #include <linux/module.h> #include <linux/platform_device.h> #include "../w1.h" #include "../w1_int.h" -/* According to the mx27 Datasheet the reset procedure should take up to about -* 1350us. We set the timeout to 500*100us = 50ms for sure */ -#define MXC_W1_RESET_TIMEOUT 500 -/* * MXC W1 Register offsets */
@@ -49,24 +46,25 @@ struct mxc_w1_device {*/ static u8 mxc_w1_ds2_reset_bus (void *data) { -u8 reg_val; -unsigned int timeout_cnt =0 ;struct mxc_w1_device *dev = data; +unsigned long timeout; -writeb (MXC_W1_CONTROL_RPP , (dev->regs +MXC_W1_CONTROL )); +writeb (MXC_W1_CONTROL_RPP , dev->regs +MXC_W1_CONTROL ); -while (1 ) { - reg_val =readb (dev->regs +MXC_W1_CONTROL ); +/* Wait for reset sequence 511+512us, use 1500us for sure */ + timeout = jiffies +usecs_to_jiffies (1500 ); -if (!(reg_val &MXC_W1_CONTROL_RPP ) || - timeout_cnt >MXC_W1_RESET_TIMEOUT ) -break ; -else - timeout_cnt++; +udelay (511 +512 ); -udelay (100 ); - } -return !(reg_val &MXC_W1_CONTROL_PST ); +do { +u8 ctrl =readb (dev->regs +MXC_W1_CONTROL ); + +/* PST bit is valid after the RPP bit is self-cleared */ +if (!(ctrl &MXC_W1_CONTROL_RPP )) +return !(ctrl &MXC_W1_CONTROL_PST ); + }while (time_is_after_jiffies (timeout)); + +return 1 ; }/*
Signature · 1 line
1.8.3.2
PATCH 3/4 w1: mxc_w1: Perform a software reset at startup
In reply to Alexander ShiyanThis patch adds a software reset for 1-Wire module at driver startup.
--- drivers/w1/masters/mxc_w1.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/w1/masters/mxc_w1.c +5 -0
@@ -32,6 +32,7 @@# define MXC_W1_CONTROL_RPP BIT(7)#define MXC_W1_TIME_DIVIDER 0x02#define MXC_W1_RESET 0x04 +# define MXC_W1_RESET_RST BIT(0)struct mxc_w1_device {void __iomem *regs;
@@ -129,6 +130,10 @@ static int mxc_w1_probe(struct platform_device *pdev)if (err)return err; +/* Software reset 1-Wire module */ +writeb (MXC_W1_RESET_RST , mdev->regs +MXC_W1_RESET ); +writeb (0 , mdev->regs +MXC_W1_RESET ); +writeb (clkdiv -1 , mdev->regs +MXC_W1_TIME_DIVIDER ); mdev->bus_master.data = mdev;
Signature · 1 line
1.8.3.2
PATCH 4/4 w1: mxc_w1: Optimize mxc_w1_ds2_touch_bit()
In reply to Alexander ShiyanAccording to the i.MX reference manual, the read/write bit operations takes from 60 us to 120 us.
This patch optimizes mxc_w1_ds2_touch_bit() function to use proper value for such delay. Nevertheless, a small margin for the timeout has been added for the case if clock frequency is inaccurate.
--- drivers/w1/masters/mxc_w1.c | 27 +++++++++++++++------------ 1 file changed, 15 insertions(+), 12 deletions(-)
drivers/w1/masters/mxc_w1.c +15 -12
@@ -75,22 +75,25 @@ static u8 mxc_w1_ds2_reset_bus(void *data)*/ static u8 mxc_w1_ds2_touch_bit (void *data,u8 bit) { -struct mxc_w1_device *mdev = data; -void __iomem *ctrl_addr = mdev->regs +MXC_W1_CONTROL ; -unsigned int timeout_cnt =400 ;/* Takes max. 120us according to -* datasheet. -*/ +struct mxc_w1_device *dev = data; +unsigned long timeout; + +writeb (MXC_W1_CONTROL_WR (bit), dev->regs +MXC_W1_CONTROL ); + +/* Wait for read/write bit (60us, Max 120us), use 200us for sure */ + timeout = jiffies +usecs_to_jiffies (200 ); -writeb (MXC_W1_CONTROL_WR (bit), ctrl_addr); +udelay (60 ); -while (timeout_cnt--) { -if (!(readb (ctrl_addr) &MXC_W1_CONTROL_WR (bit))) -break ; +do { +u8 ctrl =readb (dev->regs +MXC_W1_CONTROL ); -udelay (1 ); - } +/* RDST bit is valid after the WR1/RD bit is self-cleared */ +if (!(ctrl &MXC_W1_CONTROL_WR (bit))) +return !!(ctrl &MXC_W1_CONTROL_RDST ); + }while (time_is_after_jiffies (timeout)); -return !!(readb (ctrl_addr) &MXC_W1_CONTROL_RDST ); +return 0 ; }static int mxc_w1_probe (struct platform_device *pdev)
Signature · 1 line
1.8.3.2