platform/chrome: Add support for Acer C720
PATCH 1/1 platform/chrome: Add support for Acer C720
Acer C720 has touchpad and light sensor connected to a separate I2C buses. Since the designware I2C host controller driver has two instances on this particular machine we need a way to match the correct instance. Add support for this and then register both C720 touchpad and light sensor.
This code is based on following patch from Benson Leung:
https://patchwork.kernel.org/patch/3074411/
--- drivers/platform/chrome/chromeos_laptop.c | 45 ++++++++++++++++++++++++++----- 1 file changed, 39 insertions(+), 6 deletions(-)
drivers/platform/chrome/chromeos_laptop.c +39 -6
@@ -45,6 +45,8 @@ static const char *i2c_adapter_names[] = {"SMBus I801 adapter" ,"i915 gmbus vga" ,"i915 gmbus panel" , +"i2c-designware-pci" , + "i2c-designware-pci", };/* Keep this enum consistent with i2c_adapter_names */
@@ -52,6 +54,8 @@ enum i2c_adapter_type {I2C_ADAPTER_SMBUS =0 ,I2C_ADAPTER_VGADDC ,I2C_ADAPTER_PANEL , +I2C_ADAPTER_DESIGNWARE_0 , + I2C_ADAPTER_DESIGNWARE_1, }; struct i2c_peripheral {
@@ -183,29 +187,42 @@ static struct i2c_client *__add_probed_i2c_device(return client; } +struct i2c_lookup { +const char *name; +int instance; +int n; +}; +static int __find_i2c_adap (struct device *dev,void *data) { -const char *name = data; +struct i2c_lookup *lookup = data;static const char *prefix ="i2c-" ;struct i2c_adapter *adapter;if (strncmp (dev_name (dev), prefix,strlen (prefix)) !=0 )return 0 ; adapter =to_i2c_adapter (dev); -return (strncmp (adapter->name, name,strlen (name)) ==0 ); +if (strncmp (adapter->name, lookup->name,strlen (lookup->name)) ==0 && + lookup->n++ == lookup->instance) +return 1 ; +return 0 ; }static int find_i2c_adapter_num (enum i2c_adapter_type type) {struct device *dev =NULL ;struct i2c_adapter *adapter; -const char *name = i2c_adapter_names[type]; +struct i2c_lookup lookup; + +memset (&lookup,0 ,sizeof (lookup)); + lookup.name = i2c_adapter_names[type]; + lookup.instance = (type ==I2C_ADAPTER_DESIGNWARE_1 ) ?1 :0 ; +/* find the adapter by name */ - dev =bus_find_device (&i2c_bus_type,NULL , (void *)name, - __find_i2c_adap); + dev =bus_find_device (&i2c_bus_type,NULL , &lookup, __find_i2c_adap);if (!dev) {/* Adapters may appear later. Deferred probing will retry */ pr_notice ("%s: i2c adapter %s not found on system.\n" , __func__, - name); + lookup.name);return -ENODEV ; } adapter =to_i2c_adapter (dev);
@@ -388,6 +405,15 @@ static struct chromeos_laptop acer_ac700 = { }, }; +static struct chromeos_laptop acer_c720 = { + .i2c_peripherals = { +/* Touchpad. */ + { .add = setup_cyapa_tp,I2C_ADAPTER_DESIGNWARE_0 }, +/* Light Sensor. */ + { .add = setup_isl29018_als,I2C_ADAPTER_DESIGNWARE_1 }, + }, +}; +static struct chromeos_laptop hp_pavilion_14_chromebook = { .i2c_peripherals = {/* Touchpad. */
@@ -445,6 +471,13 @@ static struct dmi_system_id chromeos_laptop_dmi_table[] __initdata = { _CBDD(acer_ac700), }, { + .ident = "Acer C720", + .matches = { +DMI_MATCH (DMI_PRODUCT_NAME ,"Peppy" ), + }, + _CBDD(acer_c720), + }, + { .ident ="HP Pavilion 14 Chromebook" , .matches = { DMI_MATCH(DMI_PRODUCT_NAME, "Butterfly"),
Signature · 1 line
2.0.0.rc4
Benson Leung
maintainerHi Mika!
Thanks for putting this patch together. It looks like this does the job of distinguishing the two busses apart. Thanks!
Quoted 5 lines · Mika Westerberg
Acer C720 has touchpad and light sensor connected to a separate I2C buses. Since the designware I2C host controller driver has two instances on this particular machine we need a way to match the correct instance. Add support for this and then register both C720 touchpad and light sensor.
Quoted 7 lines
This code is based on following patch from Benson Leung:
https://patchwork.kernel.org/patch/3074411/
Signed-off-by Mika Westerberg <[email protected]>Tested-by Kirill A. Shutemov <[email protected]>Cc Benson Leung <[email protected]>
Since it was based on my original:
Quoted 40 lines
--- drivers/platform/chrome/chromeos_laptop.c | 45 ++++++++++++++++++++++++++----- 1 file changed, 39 insertions(+), 6 deletions(-)drivers/platform/chrome/chromeos_laptop.c +11
-1@@ -45,6 +45,8 @@ static const char *i2c_adapter_names[] = {"SMBus I801 adapter" ,"i915 gmbus vga" ,"i915 gmbus panel" , +"i2c-designware-pci" , + "i2c-designware-pci", };/* Keep this enum consistent with i2c_adapter_names */ @@ -52,6 +54,8 @@ enum i2c_adapter_type {I2C_ADAPTER_SMBUS =0 ,I2C_ADAPTER_VGADDC ,I2C_ADAPTER_PANEL , +I2C_ADAPTER_DESIGNWARE_0 , + I2C_ADAPTER_DESIGNWARE_1, }; struct i2c_peripheral {@@ -183,29 +187,42 @@ static struct i2c_client *__add_probed_i2c_device(return client; } +struct i2c_lookup { +const char *name; +int instance; +int n; +}; +static int __find_i2c_adap (struct device *dev,void *data) { -const char *name = data; +struct i2c_lookup *lookup = data;
drivers/platform/chrome/chromeos_laptop.c static struct i2c_client *__add_probed_i2c_device( · line 207
Quoted 10 lines
drivers/platform/chrome/chromeos_laptop.c +4
-1static const char *prefix ="i2c-" ;struct i2c_adapter *adapter;if (strncmp (dev_name (dev), prefix,strlen (prefix)) !=0 )return 0 ; adapter =to_i2c_adapter (dev); -return (strncmp (adapter->name, name,strlen (name)) ==0 ); +if (strncmp (adapter->name, lookup->name,strlen (lookup->name)) ==0 && + lookup->n++ == lookup->instance) +return 1 ; +return 0 ;
minor nit. This could retain the original form with a single return.
return (strncmp(adapter->name, name, strlen(name)) == 0) &&
lookup->n++ == lookup->instance);
Quoted 56 lines
drivers/platform/chrome/chromeos_laptop.c +24
-5}static int find_i2c_adapter_num (enum i2c_adapter_type type) {struct device *dev =NULL ;struct i2c_adapter *adapter; -const char *name = i2c_adapter_names[type]; +struct i2c_lookup lookup; + +memset (&lookup,0 ,sizeof (lookup)); + lookup.name = i2c_adapter_names[type]; + lookup.instance = (type ==I2C_ADAPTER_DESIGNWARE_1 ) ?1 :0 ; +/* find the adapter by name */ - dev =bus_find_device (&i2c_bus_type,NULL , (void *)name, - __find_i2c_adap); + dev =bus_find_device (&i2c_bus_type,NULL , &lookup, __find_i2c_adap);if (!dev) {/* Adapters may appear later. Deferred probing will retry */ pr_notice ("%s: i2c adapter %s not found on system.\n" , __func__, - name); + lookup.name);return -ENODEV ; } adapter =to_i2c_adapter (dev);@@ -388,6 +405,15 @@ static struct chromeos_laptop acer_ac700 = { }, }; +static struct chromeos_laptop acer_c720 = { + .i2c_peripherals = { +/* Touchpad. */ + { .add = setup_cyapa_tp,I2C_ADAPTER_DESIGNWARE_0 }, +/* Light Sensor. */ + { .add = setup_isl29018_als,I2C_ADAPTER_DESIGNWARE_1 }, + }, +}; +static struct chromeos_laptop hp_pavilion_14_chromebook = { .i2c_peripherals = {/* Touchpad. */ @@ -445,6 +471,13 @@ static struct dmi_system_id chromeos_laptop_dmi_table[] __initdata = { _CBDD(acer_ac700), }, { + .ident = "Acer C720", + .matches = { +DMI_MATCH (DMI_PRODUCT_NAME ,"Peppy" ), + }, + _CBDD(acer_c720), + }, + { .ident ="HP Pavilion 14 Chromebook" , .matches = { DMI_MATCH(DMI_PRODUCT_NAME, "Butterfly"), --
Quoted 2 lines
2.0.0.rc4
By the way, I can create patches on top of this to support the other systems that we missed as well, the HP 14, the Dell 11, the Toshiba, etc.
Signature · 3 lines
Benson Leung Software Engineer, Chrom* OS [email protected]
Quoted 15 lines · Benson Leung
Hi Mika!
Thanks for putting this patch together. It looks like this does the job of distinguishing the two busses apart. Thanks!
Quoted 7 lines · Mika Westerberg
Acer C720 has touchpad and light sensor connected to a separate I2C buses. Since the designware I2C host controller driver has two instances on this particular machine we need a way to match the correct instance. Add support for this and then register both C720 touchpad and light sensor.
This code is based on following patch from Benson Leung:
Quoted 8 lines
Quoted 5 lines
https://patchwork.kernel.org/patch/3074411/
Signed-off-by Mika Westerberg <[email protected]>Tested-by Kirill A. Shutemov <[email protected]>Cc Benson Leung <[email protected]>Since it was based on my original:
Signed-off-by Benson Leung <[email protected]>
Thanks.
Quoted 111 lines
Quoted 41 lines
--- drivers/platform/chrome/chromeos_laptop.c | 45 ++++++++++++++++++++++++++----- 1 file changed, 39 insertions(+), 6 deletions(-)drivers/platform/chrome/chromeos_laptop.c +11
-1@@ -45,6 +45,8 @@ static const char *i2c_adapter_names[] = {"SMBus I801 adapter" ,"i915 gmbus vga" ,"i915 gmbus panel" , +"i2c-designware-pci" , + "i2c-designware-pci", };/* Keep this enum consistent with i2c_adapter_names */ @@ -52,6 +54,8 @@ enum i2c_adapter_type {I2C_ADAPTER_SMBUS =0 ,I2C_ADAPTER_VGADDC ,I2C_ADAPTER_PANEL , +I2C_ADAPTER_DESIGNWARE_0 , + I2C_ADAPTER_DESIGNWARE_1, }; struct i2c_peripheral {@@ -183,29 +187,42 @@ static struct i2c_client *__add_probed_i2c_device(return client; } +struct i2c_lookup { +const char *name; +int instance; +int n; +}; +static int __find_i2c_adap (struct device *dev,void *data) { -const char *name = data; +struct i2c_lookup *lookup = data;drivers/platform/chrome/chromeos_laptop.c static struct i2c_client *__add_probed_i2c_device( · line 207
Quoted 10 lines
drivers/platform/chrome/chromeos_laptop.c +4
-1static const char *prefix ="i2c-" ;struct i2c_adapter *adapter;if (strncmp (dev_name (dev), prefix,strlen (prefix)) !=0 )return 0 ; adapter =to_i2c_adapter (dev); -return (strncmp (adapter->name, name,strlen (name)) ==0 ); +if (strncmp (adapter->name, lookup->name,strlen (lookup->name)) ==0 && + lookup->n++ == lookup->instance) +return 1 ; +return 0 ;minor nit. This could retain the original form with a single return.
return (
strncmp(adapter->name, name, strlen(name))== 0) &&lookup->n++ == lookup->instance);Quoted 54 lines
drivers/platform/chrome/chromeos_laptop.c +24
-4}static int find_i2c_adapter_num (enum i2c_adapter_type type) {struct device *dev =NULL ;struct i2c_adapter *adapter; -const char *name = i2c_adapter_names[type]; +struct i2c_lookup lookup; + +memset (&lookup,0 ,sizeof (lookup)); + lookup.name = i2c_adapter_names[type]; + lookup.instance = (type ==I2C_ADAPTER_DESIGNWARE_1 ) ?1 :0 ; +/* find the adapter by name */ - dev =bus_find_device (&i2c_bus_type,NULL , (void *)name, - __find_i2c_adap); + dev =bus_find_device (&i2c_bus_type,NULL , &lookup, __find_i2c_adap);if (!dev) {/* Adapters may appear later. Deferred probing will retry */ pr_notice ("%s: i2c adapter %s not found on system.\n" , __func__, - name); + lookup.name);return -ENODEV ; } adapter =to_i2c_adapter (dev);@@ -388,6 +405,15 @@ static struct chromeos_laptop acer_ac700 = { }, }; +static struct chromeos_laptop acer_c720 = { + .i2c_peripherals = { +/* Touchpad. */ + { .add = setup_cyapa_tp,I2C_ADAPTER_DESIGNWARE_0 }, +/* Light Sensor. */ + { .add = setup_isl29018_als,I2C_ADAPTER_DESIGNWARE_1 }, + }, +}; +static struct chromeos_laptop hp_pavilion_14_chromebook = { .i2c_peripherals = {/* Touchpad. */ @@ -445,6 +471,13 @@ static struct dmi_system_id chromeos_laptop_dmi_table[] __initdata = { _CBDD(acer_ac700), }, { + .ident = "Acer C720", + .matches = { +DMI_MATCH (DMI_PRODUCT_NAME ,"Peppy" ), + }, + _CBDD(acer_c720), + }, + { .ident ="HP Pavilion 14 Chromebook" , .matches = {
Quoted 8 lines
Quoted 4 lines
drivers/platform/chrome/chromeos_laptop.c +0
-1DMI_MATCH(DMI_PRODUCT_NAME, "Butterfly"), --2.0.0.rc4
By the way, I can create patches on top of this to support the other systems that we missed as well, the HP 14, the Dell 11, the Toshiba, etc.
Cool :)
Do you mind including $subject patch (with your suggested change above) with your patch series once v3.16-rc1 is released? Please let me know if you want me to do the change and send the patch myself.
Benson Leung
maintainerHi Mika,
Quoted 3 lines · Mika Westerberg
Do you mind including $subject patch (with your suggested change above) with your patch series once v3.16-rc1 is released? Please let me know if you want me to do the change and send the patch myself.
I'll include your Acer C720 patch along with the rest of my patches when v3.16-rc1 is released.
Thanks!
Signature · 3 lines
Benson Leung Software Engineer, Chrom* OS [email protected]
cover platform/chrome: Probe multiple i2c adapters of the same name
Would a generalized approach to the "multiple adapters with same name" problem be desirable? If so, would this approach work?
I don't have access to an Acer C720. This patch has only been tested on a Toshiba Chromebook using the "i2c: designware-pci: Add Haswell PCI IDs" patch from Mika applied to the 3.15-rc8 release.
Thanks,
Scot
PATCH 1/1 platform/chrome: Probe multiple i2c adapters of the same name
The chromeos_laptop module probes the first i2c adapter with a specific name for expected hardware. However, the Acer C720 Chromebook has two i2c adapters with the same name. This patch probes each i2c adapter with a specific name in turn, until locating the expected hardware.
---
drivers/platform/chrome/chromeos_laptop.c +20 -12
@@ -173,7 +173,7 @@ static struct i2c_client *__add_probed_i2c_device(/* add the i2c device */ client =i2c_new_probed_device (adapter, info, addrs,NULL );if (!client) -pr_err ("%s failed to register device %d-%02x\n" , +pr_debug ("%s did not add i2c device %d-%02x\n" , __func__, bus, info->addr);else pr_debug("%s added i2c device %d-%02x\n",
@@ -194,13 +194,14 @@ static int __find_i2c_adap(struct device *dev, void *data)return (strncmp (adapter->name, name,strlen (name)) ==0 ); } -static int find_i2c_adapter_num (enum i2c_adapter_type type) +static int find_i2c_next_adapter_num (enum i2c_adapter_type type, +struct device *start) {struct device *dev =NULL ;struct i2c_adapter *adapter;const char *name = i2c_adapter_names[type]; -/* find the adapter by name */ - dev =bus_find_device (&i2c_bus_type,NULL , (void *)name, +/* find the next adapter by name */ + dev =bus_find_device (&i2c_bus_type, start, (void *)name, __find_i2c_adap);if (!dev) {/* Adapters may appear later. Deferred probing will retry */
@@ -226,10 +227,17 @@ static struct i2c_client *add_probed_i2c_device(struct i2c_board_info *info, const unsigned short *addrs) { - return __add_probed_i2c_device(name, -find_i2c_adapter_num (type ), -info , -addrs ); + struct i2c_client *client = NULL; +struct device *start =NULL ; +int adapter_num =0 ; +while (!client && adapter_num >-1 ) { + adapter_num =find_i2c_next_adapter_num (type, start); + client =__add_probed_i2c_device (name, + adapter_num, + info, + addrs); + } +return client; }/*
@@ -242,10 +250,10 @@ static struct i2c_client *add_i2c_device(const char *name, struct i2c_board_info *info) {const unsigned short addr_list[] = { info->addr,I2C_CLIENT_END }; -return __add_probed_i2c_device (name, -find_i2c_adapter_num (type), - info, - addr_list); +return add_probed_i2c_device (name, + type, + info, + addr_list); }static int setup_cyapa_tp (enum i2c_adapter_type type)
Re: [PATCH 1/1] platform/chrome: Probe multiple i2c adapters of the same name
Quoted 8 lines · Scot Doyle
The
chromeos_laptopmodule probes the first i2c adapter with a specific name for expected hardware. However, the Acer C720 Chromebook has two i2c adapters with the same name. This patch probes each i2c adapter with a specific name in turn, until locating the expected hardware.Signed-off-by Scot Doyle <[email protected]>CC Benson Leung <[email protected]>CC Mika Westerberg <[email protected]>
I don't have anything against this approach.
One comment though, if you happen to have two devices with the same address but in different buses this can go wrong. Not sure how likely that will happen.
Re: [PATCH 1/1] platform/chrome: Probe multiple i2c adapters of the same name
That's a good point, I'll submit a new patch which documents this requirement. If this isn't a sufficiently robust solution, I understand.
Quoted 2 lines · Mika Westerberg
Quoted 1 line · Scot Doyle
The
chromeos_laptopmodule probes the first i2c
adapter with a specific name
Quoted 19 lines
Quoted 7 lines
for expected hardware. However, the Acer C720 Chromebook has two i2c adapters with the same name. This patch probes each i2c adapter with a specific name in turn, until locating the expected hardware.
Signed-off-by Scot Doyle <[email protected]>CC Benson Leung <[email protected]>CC Mika Westerberg <[email protected]>I don't have anything against this approach.
One comment though, if you happen to have two devices with the same address but in different buses this can go wrong. Not sure how likely that will happen.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
PATCH v2 1/1 platform/chrome: Probe multiple i2c adapters of the same name
The chromeos_laptop module probes the first i2c adapter with a specific name for expected hardware. However, the Acer C720 Chromebook has two i2c adapters with the same name. This patch probes each i2c adapter with a specific name in turn, until locating the expected hardware.
Thanks to Mika Westerberg for identifying the need for unique bus addresses within each set of identically-named adapters.
---
drivers/platform/chrome/chromeos_laptop.c +22 -12
@@ -29,6 +29,8 @@#include <linux/module.h> #include <linux/platform_device.h> +/* Note: Bus addresses must be unique within each set of identically-named +adapters on a board, otherwise device probing may fail. */ #define ATMEL_TP_I2C_ADDR 0x4b#define ATMEL_TP_I2C_BL_ADDR 0x25#define ATMEL_TS_I2C_ADDR 0x4a
@@ -173,7 +175,7 @@ static struct i2c_client *__add_probed_i2c_device(/* add the i2c device */ client =i2c_new_probed_device (adapter, info, addrs,NULL );if (!client) -pr_err ("%s failed to register device %d-%02x\n" , +pr_debug ("%s did not add i2c device %d-%02x\n" , __func__, bus, info->addr);else pr_debug("%s added i2c device %d-%02x\n",
@@ -194,13 +196,14 @@ static int __find_i2c_adap(struct device *dev, void *data)return (strncmp (adapter->name, name,strlen (name)) ==0 ); } -static int find_i2c_adapter_num (enum i2c_adapter_type type) +static int find_i2c_next_adapter_num (enum i2c_adapter_type type, +struct device *start) {struct device *dev =NULL ;struct i2c_adapter *adapter;const char *name = i2c_adapter_names[type]; -/* find the adapter by name */ - dev =bus_find_device (&i2c_bus_type,NULL , (void *)name, +/* find the next adapter by name */ + dev =bus_find_device (&i2c_bus_type, start, (void *)name, __find_i2c_adap);if (!dev) {/* Adapters may appear later. Deferred probing will retry */
@@ -226,10 +229,17 @@ static struct i2c_client *add_probed_i2c_device(struct i2c_board_info *info, const unsigned short *addrs) { - return __add_probed_i2c_device(name, -find_i2c_adapter_num (type ), -info , -addrs ); + struct i2c_client *client = NULL; +struct device *start =NULL ; +int adapter_num =0 ; +while (!client && adapter_num >-1 ) { + adapter_num =find_i2c_next_adapter_num (type, start); + client =__add_probed_i2c_device (name, + adapter_num, + info, + addrs); + } +return client; }/*
@@ -242,10 +252,10 @@ static struct i2c_client *add_i2c_device(const char *name, struct i2c_board_info *info) {const unsigned short addr_list[] = { info->addr,I2C_CLIENT_END }; -return __add_probed_i2c_device (name, -find_i2c_adapter_num (type), - info, - addr_list); +return add_probed_i2c_device (name, + type, + info, + addr_list); }static int setup_cyapa_tp (enum i2c_adapter_type type)
Re: [PATCH v2 1/1] platform/chrome: Probe multiple i2c adapters of the same name
Quoted 11 lines · Scot Doyle
The
chromeos_laptopmodule probes the first i2c adapter with a specific name for expected hardware. However, the Acer C720 Chromebook has two i2c adapters with the same name. This patch probes each i2c adapter with a specific name in turn, until locating the expected hardware.Thanks to Mika Westerberg for identifying the need for unique bus addresses within each set of identically-named adapters.
Signed-off-by Scot Doyle <[email protected]>CC Benson Leung <[email protected]>CC Mika Westerberg <[email protected]>
Few comments about style:
drivers/platform/chrome/chromeos_laptop.c line 33
Quoted 12 lines
---
drivers/platform/chrome/chromeos_laptop.c +2
-0@@ -29,6 +29,8 @@#include <linux/module.h> #include <linux/platform_device.h> +/* Note: Bus addresses must be unique within each set of identically-named +adapters on a board, otherwise device probing may fail. */
Check Documentation/CodingStyle about format of block comments.
Quoted 31 lines
drivers/platform/chrome/chromeos_laptop.c +5
-4#define ATMEL_TP_I2C_ADDR 0x4b#define ATMEL_TP_I2C_BL_ADDR 0x25#define ATMEL_TS_I2C_ADDR 0x4a@@ -173,7 +175,7 @@ static struct i2c_client *__add_probed_i2c_device(/* add the i2c device */ client =i2c_new_probed_device (adapter, info, addrs,NULL );if (!client) -pr_err ("%s failed to register device %d-%02x\n" , +pr_debug ("%s did not add i2c device %d-%02x\n" , __func__, bus, info->addr);else pr_debug("%s added i2c device %d-%02x\n",@@ -194,13 +196,14 @@ static int __find_i2c_adap(struct device *dev, void *data)return (strncmp (adapter->name, name,strlen (name)) ==0 ); } -static int find_i2c_adapter_num (enum i2c_adapter_type type) +static int find_i2c_next_adapter_num (enum i2c_adapter_type type, +struct device *start) {struct device *dev =NULL ;struct i2c_adapter *adapter;const char *name = i2c_adapter_names[type]; -/* find the adapter by name */ - dev =bus_find_device (&i2c_bus_type,NULL , (void *)name, +/* find the next adapter by name */ + dev =bus_find_device (&i2c_bus_type, start, (void *)name, __find_i2c_adap);if (!dev) {/* Adapters may appear later. Deferred probing will retry */
drivers/platform/chrome/chromeos_laptop.c static struct i2c_client *add_probed_i2c_device( · line 234
Quoted 10 lines
drivers/platform/chrome/chromeos_laptop.c +3
-4@@ -226,10 +229,17 @@ static struct i2c_client *add_probed_i2c_device(struct i2c_board_info *info, const unsigned short *addrs) { - return __add_probed_i2c_device(name, -find_i2c_adapter_num (type ), -info , -addrs ); + struct i2c_client *client = NULL; +struct device *start =NULL ; +int adapter_num =0 ;
Please add blank line here.
drivers/platform/chrome/chromeos_laptop.c static struct i2c_client *add_probed_i2c_device( · line 240
Quoted 6 lines
drivers/platform/chrome/chromeos_laptop.c +6
-0+while (!client && adapter_num >-1 ) { + adapter_num =find_i2c_next_adapter_num (type, start); + client =__add_probed_i2c_device (name, + adapter_num, + info, + addrs);
Don't the above fit into one line, specifically if you call adapter_num just num or something like that.
Quoted 7 lines
drivers/platform/chrome/chromeos_laptop.c +2
-0+ } +return client; }/* @@ -242,10 +252,10 @@ static struct i2c_client *add_i2c_device(const char *name, struct i2c_board_info *info)
drivers/platform/chrome/chromeos_laptop.c static struct i2c_client *add_i2c_device(const char *name, · line 258
Quoted 10 lines
drivers/platform/chrome/chromeos_laptop.c +4
-4{const unsigned short addr_list[] = { info->addr,I2C_CLIENT_END }; -return __add_probed_i2c_device (name, -find_i2c_adapter_num (type), - info, - addr_list); +return add_probed_i2c_device (name, + type, + info, + addr_list);
Same here.
Quoted 3 lines
drivers/platform/chrome/chromeos_laptop.c +0
-0}static int setup_cyapa_tp (enum i2c_adapter_type type)
PATCH v3 1/1 platform/chrome: Probe multiple i2c adapters of the same name
The chromeos_laptop module probes the first i2c adapter with a specific name for expected hardware. However, the Acer C720 Chromebook has two i2c adapters with the same name. This patch probes each i2c adapter with a specific name until locating the expected hardware.
Thanks to Mika Westerberg for formatting tips and identifying the need for unique bus addresses within each set of identically-named adapters.
---
drivers/platform/chrome/chromeos_laptop.c +19 -12
@@ -29,6 +29,10 @@#include <linux/module.h> #include <linux/platform_device.h> +/* +* Note: Bus addresses must be unique within each set of identically-named +* adapters on a board, otherwise device probing may fail. +*/ #define ATMEL_TP_I2C_ADDR 0x4b#define ATMEL_TP_I2C_BL_ADDR 0x25#define ATMEL_TS_I2C_ADDR 0x4a
@@ -173,7 +177,7 @@ static struct i2c_client *__add_probed_i2c_device(/* add the i2c device */ client =i2c_new_probed_device (adapter, info, addrs,NULL );if (!client) -pr_err ("%s failed to register device %d-%02x\n" , +pr_debug ("%s did not add i2c device %d-%02x\n" , __func__, bus, info->addr);else pr_debug("%s added i2c device %d-%02x\n",
@@ -194,13 +198,14 @@ static int __find_i2c_adap(struct device *dev, void *data)return (strncmp (adapter->name, name,strlen (name)) ==0 ); } -static int find_i2c_adapter_num (enum i2c_adapter_type type) +static int find_i2c_next_adapter_num (enum i2c_adapter_type type, +struct device *start) {struct device *dev =NULL ;struct i2c_adapter *adapter;const char *name = i2c_adapter_names[type]; -/* find the adapter by name */ - dev =bus_find_device (&i2c_bus_type,NULL , (void *)name, +/* find the next adapter by name */ + dev =bus_find_device (&i2c_bus_type, start, (void *)name, __find_i2c_adap);if (!dev) {/* Adapters may appear later. Deferred probing will retry */
@@ -226,10 +231,15 @@ static struct i2c_client *add_probed_i2c_device(struct i2c_board_info *info, const unsigned short *addrs) { - return __add_probed_i2c_device(name, -find_i2c_adapter_num (type ), -info , -addrs ); + struct i2c_client *client = NULL; +struct device *start =NULL ; +int num =0 ; + +while (!client && num >-1 ) { + num =find_i2c_next_adapter_num (type, start); + client =__add_probed_i2c_device (name, num, info, addrs); + } +return client; }/*
@@ -242,10 +252,7 @@ static struct i2c_client *add_i2c_device(const char *name, struct i2c_board_info *info) {const unsigned short addr_list[] = { info->addr,I2C_CLIENT_END }; -return __add_probed_i2c_device (name, -find_i2c_adapter_num (type), - info, - addr_list); +return add_probed_i2c_device (name, type, info, addr_list); }static int setup_cyapa_tp (enum i2c_adapter_type type)
Benson Leung
maintainerRe: [PATCH v3 1/1] platform/chrome: Probe multiple i2c adapters of the same name
Quoted 7 lines · Scot Doyle
The
chromeos_laptopmodule probes the first i2c adapter with a specific name for expected hardware. However, the Acer C720 Chromebook has two i2c adapters with the same name. This patch probes each i2c adapter with a specific name until locating the expected hardware.Thanks to Mika Westerberg for formatting tips and identifying the need for unique bus addresses within each set of identically-named adapters.
Scot,
Is your intention with this patch to replace the one that Mika wrote that specifically special cased the designware i2c busses? He already solved this problem in this patch.
https://patchwork.kernel.org/patch/4288591/
I'm not sure about your approach here. It looks like if there's some ambiguity in the names of the busses, you try to probe the device on every bus with that name.
We know that bus 0 is going to have the touchpad, and we know that bus 1 is going to have the touchscreen and light sensor. I'd prefer not to send extra probes for all of the combination of devices that don't exist.
Signature · 3 lines
Benson Leung Software Engineer, Chrom* OS [email protected]
Re: [PATCH v3 1/1] platform/chrome: Probe multiple i2c adapters of the same name
Quoted 16 lines · Benson Leung
Quoted 7 lines · Scot Doyle
The
chromeos_laptopmodule probes the first i2c adapter with a specific name for expected hardware. However, the Acer C720 Chromebook has two i2c adapters with the same name. This patch probes each i2c adapter with a specific name until locating the expected hardware.Thanks to Mika Westerberg for formatting tips and identifying the need for unique bus addresses within each set of identically-named adapters.
Scot,
Is your intention with this patch to replace the one that Mika wrote that specifically special cased the designware i2c busses? He already solved this problem in this patch.
https://patchwork.kernel.org/patch/4288591/
Quoted 8 lines
I'm not sure about your approach here. It looks like if there's some ambiguity in the names of the busses, you try to probe the device on every bus with that name.
We know that bus 0 is going to have the touchpad, and we know that bus 1 is going to have the touchscreen and light sensor. I'd prefer not to send extra probes for all of the combination of devices that don't exist.
In the case of the Acer C720, will the touchpad always be the first device iterated by the bus_find_device function?
My quite possibly incorrect understanding is that:
- the i2c bus numbers assigned are dynamic
- dynamic bus numbers depend on the order of device registration
- there is no guarantee of the ordering of device registration
- bus_find_device iterates by insertion order (as opposed to ascending pci device id or ascending pci hardware address)