Skip to contentSkip to conversation

ahci-platform: Bump max number of clocks to 5

PATCH Superseded Kumar Gala 3 participants 5 messages Sep 8, 2014 – Sep 9, 2014

Subsystems (3)

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore

Kumar Gala

author
#0 lore raw

PATCH v4 1/3 ahci-platform: Bump max number of clocks to 5

Qualcomm IPQ806x SoCs with SATA controllers need 5 clocks to be enabled.

---
v4:
* Updated to upstream changes

 drivers/ata/ahci.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/ata/ahci.h +1 -1
index 59ae0ee..90156ff 100644
@@ -53,7 +53,7 @@
 
 enum {
 	AHCI_MAX_PORTS		= 32,
-	AHCI_MAX_CLKS		= 4,
+	AHCI_MAX_CLKS		= 5,
 	AHCI_MAX_SG		= 168, /* hardware max is 64K */
 	AHCI_DMA_BOUNDARY	= 0xffffffff,
 	AHCI_MAX_CMDS		= 32,
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
author
#1 lore raw

PATCH v4 2/3 ata: Add Qualcomm ARM SoC AHCI SATA host controller driver

Add support for the Qualcomm AHCI SATA controller that exists on several SoC and specifically the IPQ806x family of chips. The IPQ806x SATA support requires the associated IPQ806x SATA PHY Driver to be enabled as well.

---
v4:
* Added simple PM ops implementation
* Added setting of pmalive clk

v3:
* Added comment about suspend/resume not supported
* Fixup ahci_platform_init_host for upstream change to interface
* cleanup error handling of rxoob clk, moved to devm_clk_get/put

v2:
* Fixed MODULE_LICENSE to be GPL v2

 drivers/ata/Kconfig     | 10 +++++
 drivers/ata/Makefile    |  1 +
 drivers/ata/ahci_qcom.c | 99 +++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 110 insertions(+)
 create mode 100644 drivers/ata/ahci_qcom.c
drivers/ata/Kconfig +10 -0
index e1b9278..165d2fa 100644
@@ -133,6 +133,16 @@ config AHCI_MVEBU
 
 	  If unsure, say N.
 
+config AHCI_QCOM
+	tristate "Qualcomm AHCI SATA support"
+	depends on ARCH_QCOM
+	help
+	  This option enables support for AHCI SATA controller
+	  integrated into Qualcomm ARM SoC chipsets. For more
+	  information please refer to http://www.qualcomm.com/chipsets.
+
+	  If unsure, say N.
+
 config AHCI_SUNXI
 	tristate "Allwinner sunxi AHCI SATA support"
 	depends on ARCH_SUNXI
drivers/ata/Makefile +1 -0
index ae41107..812435c 100644
@@ -13,6 +13,7 @@ obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
 obj-$(CONFIG_AHCI_DA850)	+= ahci_da850.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_MVEBU)	+= ahci_mvebu.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_QCOM)		+= ahci_qcom.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_ST)		+= ahci_st.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_TEGRA)	+= ahci_tegra.o libahci.o libahci_platform.o
drivers/ata/ahci_qcom.c new file +99 -0

99 lines not on this page · raw message

Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
author
#4 lore raw

PATCH v4 3/3 ata: qcom: Add device tree bindings information

In reply to Kumar Gala

Add device tree binding for Qualcomm AHCI SATA controller and specifically the sata controller on the IPQ806x family of SoCs.

---
 .../devicetree/bindings/ata/qcom-sata.txt          | 40 ++++++++++++++++++++++
 1 file changed, 40 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/ata/qcom-sata.txt
Documentation/devicetree/bindings/ata/qcom-sata.txt new file +40 -0
new file mode 100644
index 0000000..5e74e41
@@ -0,0 +1,40 @@
+* Qualcomm AHCI SATA Controller
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA controller should have its own node.
+
+Required properties:
+- compatible		: compatible list, contains "qcom,msm-ahci"
+- interrupts		: <interrupt mapping for SATA IRQ>
+- reg			: <registers mapping>
+- phys			: Must contain exactly one entry as specified
+			  in phy-bindings.txt
+- phy-names		: Must be "sata-phy"
+
+Required properties for "qcom,ipq806x-ahci" compatible:
+- clocks		: Must contain an entry for each entry in clock-names.
+- clock-names		: Shall be:
+				"slave_iface" - Fabric port AHB clock for SATA
+				"iface" - AHB clock
+				"core" - core clock
+				"rxoob" - RX out-of-band clock
+				"pmalive" - Power Module Alive clock
+
+Example:
+	sata at 29000000 {
+		compatible = "qcom,ipq806x-ahci", "qcom,msm-ahci";
+		reg = <0x29000000 0x180>;
+
+		interrupts = <0 209 0x0>;
+
+		clocks = <&gcc SFAB_SATA_S_H_CLK>,
+			 <&gcc SATA_H_CLK>,
+			 <&gcc SATA_A_CLK>,
+			 <&gcc SATA_RXOOB_CLK>,
+			 <&gcc SATA_PMALIVE_CLK>;
+		clock-names = "slave_iface", "iface", "core",
+				"rxoob", "pmalive";
+
+		phys = <&sata_phy>;
+		phy-names = "sata-phy";
+	};
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
#2 lore raw

Re: [PATCH v4 2/3] ata: Add Qualcomm ARM SoC AHCI SATA host controller driver

In reply to Kumar Gala
Quoted 5 lines · Kumar Gala

Add support for the Qualcomm AHCI SATA controller that exists on several SoC and specifically the IPQ806x family of chips. The IPQ806x SATA support requires the associated IPQ806x SATA PHY Driver to be enabled as well.

Please cc Hans de Goede <[email protected]> on all ahci_platform related changes.

Thanks.

Signature · 1 line
tejun
#3 lore raw

Re: [PATCH v4 2/3] ata: Add Qualcomm ARM SoC AHCI SATA host controller driver

In reply to Kumar Gala

Hi,

Quoted 3 lines · Kumar Gala

Add support for the Qualcomm AHCI SATA controller that exists on several SoC and specifically the IPQ806x family of chips. The IPQ806x SATA support requires the associated IPQ806x SATA PHY Driver to be enabled as well.

If I'm reading this driver correctly, all it does which ahci_platform.c does not do is set the speed for 2 clocks, or am I missing something ?

If I'm correct, then why not simply use the following in the devicetree node ? :

	sata at 29000000 {
		compatible = "qcom,ipq806x-ahci", "qcom,msm-ahci", "generic-ahci";
		reg = <0x29000000 0x180>;

		interrupts = <0 209 0x0>;

		clocks = <&gcc SFAB_SATA_S_H_CLK>,
			 <&gcc SATA_H_CLK>,
			 <&gcc SATA_A_CLK>,
			 <&gcc SATA_RXOOB_CLK>,
			 <&gcc SATA_PMALIVE_CLK>;
		clock-names = "slave_iface", "iface", "core",
				"rxoob", "pmalive";

		assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
		assigned-clock-rates = <100000000>, <100000000>;

		phys = <&sata_phy>;
		phy-names = "sata-phy";
	};

Notice the "generic-ahci" and assigned-clock* properties, see:

Documentation/devicetree/bindings/clock/clock-bindings.txt

With this you don't need to write your own driver at all, just a patch to increase the max clocks + a dts node.

In case you do need your own driver for some reason see my review comments on the driver further down.

Quoted 97 lines

---
v4:
* Added simple PM ops implementation
* Added setting of pmalive clk

v3:
* Added comment about suspend/resume not supported
* Fixup ahci_platform_init_host for upstream change to interface
* cleanup error handling of rxoob clk, moved to devm_clk_get/put

v2:
* Fixed MODULE_LICENSE to be GPL v2

 drivers/ata/Kconfig     | 10 +++++
 drivers/ata/Makefile    |  1 +
 drivers/ata/ahci_qcom.c | 99 +++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 110 insertions(+)
 create mode 100644 drivers/ata/ahci_qcom.c
drivers/ata/Kconfig +10 -0
index e1b9278..165d2fa 100644
@@ -133,6 +133,16 @@ config AHCI_MVEBU
 
 	  If unsure, say N.
 
+config AHCI_QCOM
+	tristate "Qualcomm AHCI SATA support"
+	depends on ARCH_QCOM
+	help
+	  This option enables support for AHCI SATA controller
+	  integrated into Qualcomm ARM SoC chipsets. For more
+	  information please refer to http://www.qualcomm.com/chipsets.
+
+	  If unsure, say N.
+
 config AHCI_SUNXI
 	tristate "Allwinner sunxi AHCI SATA support"
 	depends on ARCH_SUNXI
drivers/ata/Makefile +1 -0
index ae41107..812435c 100644
@@ -13,6 +13,7 @@ obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
 obj-$(CONFIG_AHCI_DA850)	+= ahci_da850.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_MVEBU)	+= ahci_mvebu.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_QCOM)		+= ahci_qcom.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_ST)		+= ahci_st.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_TEGRA)	+= ahci_tegra.o libahci.o libahci_platform.o
drivers/ata/ahci_qcom.c new file +37 -0
new file mode 100644
index 0000000..3da0c94
@@ -0,0 +1,99 @@
+/*
+ * Qualcomm ARM SoC AHCI SATA platform driver
+ *
+ * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov
+ *
+ * Copyright (c) 2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/ahci_platform.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/libata.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include "ahci.h"
+
+static const struct ata_port_info qcom_ahci_port_info = {
+	.flags		= AHCI_FLAG_COMMON,
+	.pio_mask	= ATA_PIO4,
+	.udma_mask	= ATA_UDMA6,
+	.port_ops	= &ahci_platform_ops,
+};
+
+static int qcom_ahci_probe(struct platform_device *pdev)
+{
+	struct ahci_host_priv *hpriv;
+	struct clk *rxoob_clk, *pmalive_clk;

drivers/ata/ahci_qcom.c line 47

Quoted 10 lines
drivers/ata/ahci_qcom.c new file +10 -0
+	int rc;
+
+	hpriv = ahci_platform_get_resources(pdev);
+	if (IS_ERR(hpriv))
+		return PTR_ERR(hpriv);
+
+	/* Try and set the rxoob clk to 100Mhz */
+	rxoob_clk = of_clk_get_by_name(pdev->dev.of_node, "rxoob");
+	if (IS_ERR(rxoob_clk))
+		return PTR_ERR(rxoob_clk);

You're leaking the reference to the clk you're getting here. Please do one of the following to fix this:

1) Use devm_clk_get; or
2) Since ahci_platform_get_resources also got a reference,
you can put the clk after having set the rate; or
3) Since you specify a fixed clock order in your dts bindings, at defines for the clock indexes, and just use hpriv->clks[DEFINE] to set the rates.

Otherwise this looks good, although I would prefer to not have a separate driver for this at all, see above.

Regards,

Hans

Quoted 53 lines
drivers/ata/ahci_qcom.c new file +52 -0
+
+	rc = clk_set_rate(rxoob_clk, 100000000);
+	if (rc)
+		return rc;
+
+	/* Try and set the pmalive clk to 100Mhz */
+	pmalive_clk = of_clk_get_by_name(pdev->dev.of_node, "pmalive");
+	if (IS_ERR(pmalive_clk))
+		return PTR_ERR(pmalive_clk);
+
+	rc = clk_set_rate(pmalive_clk, 100000000);
+	if (rc)
+		return rc;
+
+	rc = ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
+
+	rc = ahci_platform_init_host(pdev, hpriv, &qcom_ahci_port_info);
+	if (rc)
+		goto disable_resources;
+
+	return 0;
+disable_resources:
+	ahci_platform_disable_resources(hpriv);
+	return rc;
+}
+
+static const struct of_device_id qcom_ahci_of_match[] = {
+	{ .compatible = "qcom,msm-ahci", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, qcom_ahci_of_match);
+
+static SIMPLE_DEV_PM_OPS(qcom_ahci_pm_ops, ahci_platform_suspend,
+			 ahci_platform_resume);
+
+static struct platform_driver qcom_ahci_driver = {
+	.probe = qcom_ahci_probe,
+	.remove = ata_platform_remove_one,
+	.driver = {
+		.name = "qcom_ahci_qcom",
+		.owner = THIS_MODULE,
+		.of_match_table = qcom_ahci_of_match,
+		.pm = &qcom_ahci_pm_ops,
+	},
+};
+module_platform_driver(qcom_ahci_driver);
+
+MODULE_DESCRIPTION("Qualcomm AHCI SATA platform driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("ahci:qcom");