ASoC: wm8960: Let wm8960 codec driver manage its own MCLK
Subsystems (3)
PATCH 1/4 ASoC: wm8960: Let wm8960 codec driver manage its own MCLK
When we want to use wm8960 codec, we should enable its MCLK in machine driver. It's reasonable for wm8960 codec driver to manage its own MCLK.
When current bias_level is SND_SOC_BIAS_ON, it is preparing for a transition away from ON. In this case, disable the codec mclk. When current bias_level is not SND_SOC_BIAS_ON, it preparing for a transition to ON. In this case, enable the codec mclk.
--- sound/soc/codecs/wm8960.c | 40 +++++++++++++++++++++++++++++++++++++++- 1 file changed, 39 insertions(+), 1 deletion(-)
sound/soc/codecs/wm8960.c +39 -1
@@ -15,6 +15,7 @@#include <linux/init.h> #include <linux/delay.h> #include <linux/pm.h> +#include <linux/clk.h> #include <linux/i2c.h> #include <linux/slab.h> #include <sound/core.h>
@@ -117,6 +118,7 @@ static bool wm8960_volatile(struct device *dev, unsigned int reg) }struct wm8960_priv { +struct clk *mclk;struct regmap *regmap;int (*set_bias_level)(struct snd_soc_codec *,enum snd_soc_bias_level level);
@@ -618,6 +620,7 @@ static int wm8960_set_bias_level_out3(struct snd_soc_codec *codec, enum snd_soc_bias_level level) {struct wm8960_priv *wm8960 =snd_soc_codec_get_drvdata (codec); +int ret;switch (level) {case SND_SOC_BIAS_ON :
@@ -626,6 +629,20 @@ static int wm8960_set_bias_level_out3(struct snd_soc_codec *codec,case SND_SOC_BIAS_PREPARE :/* Set VMID to 2x50k */ snd_soc_update_bits (codec,WM8960_POWER1 ,0x180 ,0x80 ); + +if (!IS_ERR (wm8960->mclk)) { +if (codec->dapm.bias_level ==SND_SOC_BIAS_ON ) +clk_disable_unprepare (wm8960->mclk); +else { + ret =clk_prepare_enable (wm8960->mclk); +if (ret) { +dev_err (codec->dev, +"Failed to enable MCLK: %d\n" , + ret); +return ret; + } + } + }break ;case SND_SOC_BIAS_STANDBY :
@@ -661,6 +678,7 @@ static int wm8960_set_bias_level_out3(struct snd_soc_codec *codec,/* Disable VMID and VREF, let them discharge */ snd_soc_write (codec,WM8960_POWER1 ,0 ); +msleep (600 );break ; }
@@ -674,7 +692,7 @@ static int wm8960_set_bias_level_capless(struct snd_soc_codec *codec, enum snd_soc_bias_level level) {struct wm8960_priv *wm8960 =snd_soc_codec_get_drvdata (codec); -int reg; +int reg, ret;switch (level) {case SND_SOC_BIAS_ON :
@@ -715,9 +733,22 @@ static int wm8960_set_bias_level_capless(struct snd_soc_codec *codec, WM8960_VREF, WM8960_VREF);msleep (100 ); + +if (!IS_ERR (wm8960->mclk)) { + ret =clk_prepare_enable (wm8960->mclk); +if (ret) { +dev_err (codec->dev, +"Failed to enable MCLK: %d\n" , + ret); +return ret; + } + }break ;case SND_SOC_BIAS_ON : +if (!IS_ERR (wm8960->mclk)) +clk_disable_unprepare (wm8960->mclk); +/* Enable anti-pop mode */ snd_soc_update_bits(codec, WM8960_APOP1, WM8960_POBCTRL | WM8960_SOFT_ST |
@@ -728,6 +759,7 @@ static int wm8960_set_bias_level_capless(struct snd_soc_codec *codec,/* Disable VMID and VREF */ snd_soc_update_bits (codec,WM8960_POWER1 ,WM8960_VREF |WM8960_VMID_MASK ,0 ); +break ;case SND_SOC_BIAS_OFF :
@@ -1002,6 +1034,12 @@ static int wm8960_i2c_probe(struct i2c_client *i2c,if (wm8960 ==NULL )return -ENOMEM ; + wm8960->mclk =devm_clk_get (&i2c->dev,"codec_mclk" ); +if (IS_ERR (wm8960->mclk)) { +if (PTR_ERR (wm8960->mclk) == -EPROBE_DEFER ) +return -EPROBE_DEFER ; + } + wm8960->regmap =devm_regmap_init_i2c (i2c, &wm8960_regmap);if (IS_ERR (wm8960->regmap))return PTR_ERR (wm8960->regmap);
Signature · 1 line
1.9.1
PATCH 2/4 ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock
wm8960 codec driver missing configure its bit clock and frame clock, so add support for it. It will calculate a appropriate frequency dividing ratio according to the system clock, bit clock and frame clock, then set the corresponding registers.
--- sound/soc/codecs/wm8960.c | 108 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 108 insertions(+)
sound/soc/codecs/wm8960.c +108 -0
@@ -127,6 +127,8 @@ struct wm8960_priv {struct snd_soc_dapm_widget *out3;bool deemph;int playback_fs; +int bclk; +int sysclk;struct wm8960_data pdata; };
@@ -563,6 +565,79 @@ static struct { { 8000, 5 }, }; +/* Multiply 256 for internal 256 div */ +static const int dac_divs[] = {256 ,384 ,512 ,768 ,1024 ,1408 ,1536 }; + +/* Multiply 10 to eliminate decimials */ +static const int bclk_divs[] = { +10 ,15 ,20 ,30 ,40 ,55 ,60 ,80 ,110 , +120 ,160 ,220 ,240 ,320 ,320 ,320 +}; + +static void wm8960_configure_clocking (struct snd_soc_codec *codec, +int stream,int lrclk) +{ +struct wm8960_priv *wm8960 =snd_soc_codec_get_drvdata (codec); +u16 iface1 =snd_soc_read (codec,WM8960_IFACE1 ); +u16 iface2 =snd_soc_read (codec,WM8960_IFACE2 ); +int i, j; + +if (!(iface1 & (1 <<6 ))) { +dev_dbg (codec->dev, +"Codec is slave mode, no need to configure clock\n" ); +return ; + } + +if (!wm8960->sysclk) { +dev_dbg (codec->dev,"No SYSCLK configured\n" ); +return ; + } + +if (!wm8960->bclk || !lrclk) { +dev_dbg (codec->dev,"No audio clocks configured\n" ); +return ; + } + +for (i =0 ; i <ARRAY_SIZE (dac_divs); ++i) { +if (wm8960->sysclk == lrclk * dac_divs[i]) { +for (j =0 ; j <ARRAY_SIZE (bclk_divs); ++j) { +if (wm8960->sysclk == wm8960->bclk * + bclk_divs[j] /10 ) { +/* configure frame clock */ +if (iface2 & (1 <<6 )) +/* If ADCLRC configure as GPIO +* pin, DACLRC pin is used as +* a frame clock for ADCs and +* DACs */ +snd_soc_update_bits (codec, +WM8960_CLOCK1 , +0x7 <<3 , + i <<3 ); +else if (SNDRV_PCM_STREAM_PLAYBACK + == stream) +snd_soc_update_bits (codec, +WM8960_CLOCK1 , +0x7 <<3 , + i <<3 ); +else if (SNDRV_PCM_STREAM_CAPTURE + == stream) +snd_soc_update_bits (codec, +WM8960_CLOCK1 , +0x7 <<6 , + i <<6 ); + +/* configure bit clock */ +snd_soc_update_bits (codec, +WM8960_CLOCK2 ,0xf , j); +return ; + } + } + } + } + +dev_err (codec->dev,"Unsupported sysclk %d\n" , wm8960->sysclk); +} +static int wm8960_hw_params (struct snd_pcm_substream *substream,struct snd_pcm_hw_params *params,struct snd_soc_dai *dai)
@@ -572,6 +647,10 @@ static int wm8960_hw_params(struct snd_pcm_substream *substream,u16 iface =snd_soc_read (codec,WM8960_IFACE1 ) &0xfff3 ;int i; + wm8960->bclk =snd_soc_params_to_bclk (params); +if (params_channels (params) ==1 ) + wm8960->bclk *=2 ; +/* bit size */ switch (params_width (params)) {case 16 :
@@ -602,6 +681,10 @@ static int wm8960_hw_params(struct snd_pcm_substream *substream,/* set iface */ snd_soc_write (codec,WM8960_IFACE1 , iface); + +wm8960_configure_clocking (codec, substream->stream, +params_rate (params)); +return 0 ; }
@@ -943,6 +1026,30 @@ static int wm8960_set_bias_level(struct snd_soc_codec *codec,return wm8960->set_bias_level (codec, level); } +static int wm8960_set_dai_sysclk (struct snd_soc_dai *dai,int clk_id, +unsigned int freq,int dir) +{ +struct snd_soc_codec *codec = dai->codec; +struct wm8960_priv *wm8960 =snd_soc_codec_get_drvdata (codec); + +switch (clk_id) { +case WM8960_SYSCLK_MCLK : +snd_soc_update_bits (codec,WM8960_CLOCK1 , +0x1 ,WM8960_SYSCLK_MCLK ); +break ; +case WM8960_SYSCLK_PLL : +snd_soc_update_bits (codec,WM8960_CLOCK1 , +0x1 ,WM8960_SYSCLK_PLL ); +break ; +default : +return -EINVAL ; + } + + wm8960->sysclk = freq; + +return 0 ; +} +#define WM8960_RATES SNDRV_PCM_RATE_8000_48000#define WM8960_FORMATS \
@@ -955,6 +1062,7 @@ static const struct snd_soc_dai_ops wm8960_dai_ops = { .set_fmt = wm8960_set_dai_fmt, .set_clkdiv = wm8960_set_dai_clkdiv, .set_pll = wm8960_set_dai_pll, + .set_sysclk = wm8960_set_dai_sysclk, };static struct snd_soc_dai_driver wm8960_dai = {
Signature · 1 line
1.9.1
Re: [alsa-devel][PATCH 2/4] ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock
Quoted 65 lines · Zidan Wang
wm8960 codec driver missing configure its bit clock and frame clock, so add support for it. It will calculate a appropriate frequency dividing ratio according to the system clock, bit clock and frame clock, then set the corresponding registers.
Signed-off-by Zidan Wang <[email protected]>--- sound/soc/codecs/wm8960.c | 108 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 108 insertions(+)sound/soc/codecs/wm8960.c +40
-0@@ -127,6 +127,8 @@ struct wm8960_priv {struct snd_soc_dapm_widget *out3;bool deemph;int playback_fs; +int bclk; +int sysclk;struct wm8960_data pdata; };@@ -563,6 +565,79 @@ static struct { { 8000, 5 }, }; +/* Multiply 256 for internal 256 div */ +static const int dac_divs[] = {256 ,384 ,512 ,768 ,1024 ,1408 ,1536 }; + +/* Multiply 10 to eliminate decimials */ +static const int bclk_divs[] = { +10 ,15 ,20 ,30 ,40 ,55 ,60 ,80 ,110 , +120 ,160 ,220 ,240 ,320 ,320 ,320 +}; + +static void wm8960_configure_clocking (struct snd_soc_codec *codec, +int stream,int lrclk) +{ +struct wm8960_priv *wm8960 =snd_soc_codec_get_drvdata (codec); +u16 iface1 =snd_soc_read (codec,WM8960_IFACE1 ); +u16 iface2 =snd_soc_read (codec,WM8960_IFACE2 ); +int i, j; + +if (!(iface1 & (1 <<6 ))) { +dev_dbg (codec->dev, +"Codec is slave mode, no need to configure clock\n" ); +return ; + } + +if (!wm8960->sysclk) { +dev_dbg (codec->dev,"No SYSCLK configured\n" ); +return ; + } + +if (!wm8960->bclk || !lrclk) { +dev_dbg (codec->dev,"No audio clocks configured\n" ); +return ; + } + +for (i =0 ; i <ARRAY_SIZE (dac_divs); ++i) { +if (wm8960->sysclk == lrclk * dac_divs[i]) { +for (j =0 ; j <ARRAY_SIZE (bclk_divs); ++j) { +if (wm8960->sysclk == wm8960->bclk * + bclk_divs[j] /10 ) {
sound/soc/codecs/wm8960.c static struct { · line 615
Quoted 10 lines
sound/soc/codecs/wm8960.c +10
-0+/* configure frame clock */ +if (iface2 & (1 <<6 )) +/* If ADCLRC configure as GPIO +* pin, DACLRC pin is used as +* a frame clock for ADCs and +* DACs */ +snd_soc_update_bits (codec, +WM8960_CLOCK1 , +0x7 <<3 , + i <<3 );
The indentation is getting pretty horrific here can we do some things to ease that a little. You could flip the polarity of the two if statements and use continues instead for example that would help a lot.
Thanks,
Charles
Quoted 25 lines
sound/soc/codecs/wm8960.c +25
-0+else if (SNDRV_PCM_STREAM_PLAYBACK + == stream) +snd_soc_update_bits (codec, +WM8960_CLOCK1 , +0x7 <<3 , + i <<3 ); +else if (SNDRV_PCM_STREAM_CAPTURE + == stream) +snd_soc_update_bits (codec, +WM8960_CLOCK1 , +0x7 <<6 , + i <<6 ); + +/* configure bit clock */ +snd_soc_update_bits (codec, +WM8960_CLOCK2 ,0xf , j); +return ; + } + } + } + } + +dev_err (codec->dev,"Unsupported sysclk %d\n" , wm8960->sysclk); +} +
PATCH 3/4 ASoC: wm8960: use pr_debug instead of pr_err
In reply to Zidan WangIn machine driver, we should find a appropriate sysclk for codec driver, and will use codec set_dai_pll to judge if pll can generate such sysclk. When sample rate changed, we should look for a useful bclk, lrclk division ratio, and will try set_dai_pll for several times. So use pr_debug so that don't generate much error logs.
--- sound/soc/codecs/wm8960.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/wm8960.c +1 -1
@@ -914,7 +914,7 @@ static int pll_factors(unsigned int source, unsigned int target, pll_div->pre_div =0 ;if ((Ndiv <6 ) || (Ndiv >12 )) { -pr_err ("WM8960 PLL: Unsupported N=%d\n" , Ndiv); +pr_debug ("WM8960 PLL: Unsupported N=%d\n" , Ndiv);return -EINVAL ; }
Signature · 1 line
1.9.1
PATCH 4/4 ASoC: wm8960: Fix capture sample rate from 11250 to 11025
In reply to Zidan Wangwm8960 codec can't support sample rate 11250, it must be 11025.
--- sound/soc/codecs/wm8960.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/wm8960.c +1 -1
@@ -560,7 +560,7 @@ static struct { { 22050, 2 }, { 24000, 2 }, { 16000, 3 }, - { 11250, 4 }, + { 11025, 4 }, { 12000, 4 }, { 8000, 5 }, };
Signature · 1 line
1.9.1
Re: [alsa-devel][PATCH 4/4] ASoC: wm8960: Fix capture sample rate from 11250 to 11025
Quoted 4 lines · Zidan Wang
wm8960 codec can't support sample rate 11250, it must be 11025.
Signed-off-by Zidan Wang <[email protected]>---
Thanks,
Charles
Re: [alsa-devel][PATCH 4/4] ASoC: wm8960: Fix capture sample rate from 11250 to 11025
In reply to Zidan WangQuoted 1 line · Zidan Wang
wm8960 codec can't support sample rate 11250, it must be 11025.
Applied, thanks.
Mark Brown
maintainersound/soc/codecs/wm8960.c static int wm8960_set_bias_level_out3(struct snd_soc_codec *codec, · line 636
Quoted 4 lines · Zidan Wang
sound/soc/codecs/wm8960.c +4
-0+if (!IS_ERR (wm8960->mclk)) { +if (codec->dapm.bias_level ==SND_SOC_BIAS_ON ) +clk_disable_unprepare (wm8960->mclk); +else {
Both sides of the if statement should have braces if one does, though in this case nesting a second switch statement would probably be clearer.
sound/soc/codecs/wm8960.c static int wm8960_set_bias_level_out3(struct snd_soc_codec *codec, · line 684
Quoted 8 lines
sound/soc/codecs/wm8960.c +1
-0@@ -661,6 +678,7 @@ static int wm8960_set_bias_level_out3(struct snd_soc_codec *codec,/* Disable VMID and VREF, let them discharge */ snd_soc_write (codec,WM8960_POWER1 ,0 ); +msleep (600 );break ; }
Random while space change here and in a couple of other places.
sound/soc/codecs/wm8960.c static int wm8960_i2c_probe(struct i2c_client *i2c, · line 1042
Quoted 6 lines
sound/soc/codecs/wm8960.c +6
-0+ wm8960->mclk =devm_clk_get (&i2c->dev,"codec_mclk" ); +if (IS_ERR (wm8960->mclk)) { +if (PTR_ERR (wm8960->mclk) == -EPROBE_DEFER ) +return -EPROBE_DEFER ; + } +
Why name this "codec_mclk" - the device calls it just MCLK?