Documentation: devicetree: Fix double words in Doumentation/devicetree
Subsystems (10)
PATCH 1/1 Documentation: devicetree: Fix double words in Doumentation/devicetree
This patch fix multiple words such as "the the" and "which which" in Documentation/devicetree.
Signed-off-by Masanari Iida <[email protected]>
--- Documentation/devicetree/bindings/arm/msm/timer.txt | 2 +- Documentation/devicetree/bindings/ata/cavium-compact-flash.txt | 2 +- Documentation/devicetree/bindings/c6x/dscr.txt | 2 +- Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt | 2 +- Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt | 2 +- Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt | 2 +- Documentation/devicetree/bindings/mtd/fsmc-nand.txt | 2 +- Documentation/devicetree/bindings/net/broadcom-systemport.txt | 2 +- Documentation/devicetree/bindings/power/rockchip-io-domain.txt | 2 +- Documentation/devicetree/overlay-notes.txt | 4 ++-- 10 files changed, 11 insertions(+), 11 deletions(-)
Documentation/devicetree/bindings/arm/msm/timer.txt +1 -1
@@ -8,7 +8,7 @@ Properties: "qcom,kpss-timer" - krait subsystem "qcom,scss-timer" - scorpion subsystem -- interrupts : Interrupts for the the debug timer, the first general purpose +- interrupts : Interrupts for the debug timer, the first general purpose timer, and optionally a second general purpose timer in that order.
Documentation/devicetree/bindings/ata/cavium-compact-flash.txt +1 -1
@@ -9,7 +9,7 @@ Properties: Compatibility with many Cavium evaluation boards. -- reg: The base address of the the CF chip select banks. Depending on +- reg: The base address of the CF chip select banks. Depending on the device configuration, there may be one or two banks. - cavium,bus-width: The width of the connection to the CF devices. Valid
Documentation/devicetree/bindings/c6x/dscr.txt +1 -1
@@ -12,7 +12,7 @@ configuration register for writes. These configuration register may be used to enable (and disable in some cases) SoC pin drivers, select peripheral clock sources (internal or pin), etc. In some cases, a configuration register is write once or the individual bits are write once. In addition to device config, -the DSCR block may provide registers which which are used to reset peripherals, +the DSCR block may provide registers which are used to reset peripherals, provide device ID information, provide ethernet MAC addresses, as well as other miscellaneous functions.
Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +1 -1
@@ -1,6 +1,6 @@ * Renesas R-Car DMA Controller Device Tree bindings -Renesas R-Car Generation 2 SoCs have have multiple multi-channel DMA +Renesas R-Car Generation 2 SoCs have multiple multi-channel DMA controller instances named DMAC capable of serving multiple clients. Channels can be dedicated to specific clients or shared between a large number of clients.
Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt +1 -1
@@ -39,7 +39,7 @@ Optional Properties: - lines-initial-states: Bitmask that specifies the initial state of each line. When a bit is set to zero, the corresponding line will be initialized to the input (pulled-up) state. When the bit is set to one, the line will be - initialized the the low-level output state. If the property is not specified + initialized the low-level output state. If the property is not specified all lines will be initialized to the input state. The I/O expander can detect input state changes, and thus optionally act as
Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt +1 -1
@@ -59,7 +59,7 @@ Optional properties: Each child node represents one channel and has the following properties: Required properties: - * reg: Pair of pins the the channel is connected to. + * reg: Pair of pins the channel is connected to. 0: VP/VN 1: VAUXP[0]/VAUXN[0] 2: VAUXP[1]/VAUXN[1]
Documentation/devicetree/bindings/mtd/fsmc-nand.txt +1 -1
@@ -9,7 +9,7 @@ Required properties: Optional properties: - bank-width : Width (in bytes) of the device. If not present, the width defaults to 1 byte -- nand-skip-bbtscan: Indicates the the BBT scanning should be skipped +- nand-skip-bbtscan: Indicates the BBT scanning should be skipped - timings: array of 6 bytes for NAND timings. The meanings of these bytes are: byte 0 TCLR : CLE to RE delay in number of AHB clock cycles, only 4 bits
Documentation/devicetree/bindings/net/broadcom-systemport.txt +1 -1
@@ -3,7 +3,7 @@ Required properties: - compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport" - reg: address and length of the register set for the device. -- interrupts: interrupts for the device, first cell must be for the the rx +- interrupts: interrupts for the device, first cell must be for the rx interrupts, and the second cell should be for the transmit queues. An optional third interrupt cell for Wake-on-LAN can be specified - local-mac-address: Ethernet MAC address (48 bits) of this adapter
Documentation/devicetree/bindings/power/rockchip-io-domain.txt +1 -1
@@ -37,7 +37,7 @@ Required properties: You specify supplies using the standard regulator bindings by including -a phandle the the relevant regulator. All specified supplies must be able +a phandle the relevant regulator. All specified supplies must be able to report their voltage. The IO Voltage Domain for any non-specified supplies will be not be touched.
Documentation/devicetree/overlay-notes.txt +2 -2
@@ -10,7 +10,7 @@ How overlays work ----------------- A Device Tree's overlay purpose is to modify the kernel's live tree, and -have the modification affecting the state of the the kernel in a way that +have the modification affecting the state of the kernel in a way that is reflecting the changes. Since the kernel mainly deals with devices, any new device node that result in an active device should have it created while if the device node is either
@@ -80,7 +80,7 @@ result in foo+bar.dts }; ---- foo+bar.dts ------------------------------------------------------------- -As a result of the the overlay, a new device node (bar) has been created +As a result of the overlay, a new device node (bar) has been created so a bar platform device will be registered and if a matching device driver is loaded the device will be created as expected.
Signature · 1 line
2.2.1.62.g3f15098
Jonathan Corbet
AppliedQuoted 2 lines · On Fri, 2 Jan 2015 22:54:39 +0900 Masanari Iida <[email protected]> wrote:
This patch fix multiple words such as "the the" and "which which" in
Documentation/devicetree.
Applied to the docs tree, thanks.
jon