Skip to contentSkip to conversation

hwmon: (ina2xx) Add ina231 compatible string

PATCH Applied Kevin Hilman 2 participants 3 messages Jan 15, 2015

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 hwmon: (ina2xx) Add ina231 compatible string

From: Kevin Hilman <[email protected]>

Add support for "ina231" as compatible string, and update Documentation and Kconfig accordingly.

Tested with the Exynos5422-based odroid-xu3 board which has on-board INA231 sensors.

---
 Documentation/hwmon/ina2xx | 9 +++++++++
 drivers/hwmon/Kconfig      | 4 ++--
 drivers/hwmon/ina2xx.c     | 1 +
 3 files changed, 12 insertions(+), 2 deletions(-)
Documentation/hwmon/ina2xx +9 -0
index 4223c2d3b508..c2f838f65ee4 100644
@@ -26,6 +26,12 @@ Supported chips:
     Datasheet: Publicly available at the Texas Instruments website
                http://www.ti.com/
 
+  * Texas Instruments INA231
+    Prefix: 'ina231'
+    Addresses: I2C 0x40 - 0x4f
+    Datasheet: Publicly available at the Texas Instruments website
+               http://www.ti.com/
+
 Author: Lothar Felten <[email protected]>
 
 Description
@@ -44,6 +50,9 @@ The INA226 monitors both a shunt voltage drop and bus supply voltage.
 The INA230 is a high or low side current shunt and power monitor with an I2C
 interface. The INA230 monitors both a shunt voltage drop and bus supply voltage.
 
+The INA231 is a high or low side current shunt and power monitor with an I2C
+interface. The INA230 monitors both a shunt voltage drop and bus supply voltage.
+
 The shunt value in micro-ohms can be set via platform data or device tree.
 Please refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings
 if the device tree is used.
drivers/hwmon/Kconfig +2 -2
index 6529c09c46f0..408fb6f5f055 100644
@@ -1420,8 +1420,8 @@ config SENSORS_INA2XX
 	tristate "Texas Instruments INA219 and compatibles"
 	depends on I2C
 	help
-	  If you say yes here you get support for INA219, INA220, INA226, and
-	  INA230 power monitor chips.
+	  If you say yes here you get support for INA219, INA220, INA226,
+	  INA230, and INA231 power monitor chips.
 
 	  The INA2xx driver is configured for the default configuration of
 	  the part as described in the datasheet.
drivers/hwmon/ina2xx.c +1 -0
index e01feba909c3..8c4a29bd2eaf 100644
@@ -287,6 +287,7 @@ static const struct i2c_device_id ina2xx_id[] = {
 	{ "ina220", ina219 },
 	{ "ina226", ina226 },
 	{ "ina230", ina226 },
+	{ "ina231", ina226 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, ina2xx_id);
Signature · 1 line
2.1.3
maintainer Applied
#1 lore raw
Quoted 9 lines · Kevin Hilman

From: Kevin Hilman <[email protected]>

Add support for "ina231" as compatible string, and update Documentation and Kconfig accordingly.

Tested with the Exynos5422-based odroid-xu3 board which has on-board INA231 sensors.

Applied to -next after minor cleanup (see below).

Quoted 24 lines
---
  Documentation/hwmon/ina2xx | 9 +++++++++
  drivers/hwmon/Kconfig      | 4 ++--
  drivers/hwmon/ina2xx.c     | 1 +
  3 files changed, 12 insertions(+), 2 deletions(-)
Documentation/hwmon/ina2xx +6 -0
index 4223c2d3b508..c2f838f65ee4 100644
@@ -26,6 +26,12 @@ Supported chips:
      Datasheet: Publicly available at the Texas Instruments website
                 http://www.ti.com/
 
+  * Texas Instruments INA231
+    Prefix: 'ina231'
+    Addresses: I2C 0x40 - 0x4f
+    Datasheet: Publicly available at the Texas Instruments website
+               http://www.ti.com/
+
  Author: Lothar Felten <[email protected]>
 
  Description

Documentation/hwmon/ina2xx The INA226 monitors both a shunt voltage drop and bus supply voltage. · line 55

Quoted 6 lines
Documentation/hwmon/ina2xx +3 -0
@@ -44,6 +50,9 @@ The INA226 monitors both a shunt voltage drop and bus supply voltage.
  The INA230 is a high or low side current shunt and power monitor with an I2C
  interface. The INA230 monitors both a shunt voltage drop and bus supply voltage.
 
+The INA231 is a high or low side current shunt and power monitor with an I2C
+interface. The INA230 monitors both a shunt voltage drop and bus supply voltage.
+
		The INA231 ...

I fixed this up and merged above two paragraphs into one.

Guenter

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors

#2 lore raw
Quoted 6 lines · Guenter Roeck
Quoted 5 lines · Kevin Hilman

From: Kevin Hilman <[email protected]>

Add support for "ina231" as compatible string, and update Documentation and Kconfig accordingly.

Quoted 7 lines
Quoted 4 lines

Tested with the Exynos5422-based odroid-xu3 board which has on-board INA231 sensors.

Applied to -next after minor cleanup (see below).

Thanks,

Kevin

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors