rocker: add new rocker ethernet switch device

new file mode 100644
index 0000000..fa9db19
@@ -0,0 +1,960 @@
+Rocker Network Switch Register Programming Guide
+Copyright (c) Scott Feldman <[email protected]>
+Copyright (c) Neil Horman <[email protected]>
+Version 0.11, 12/29/2014
+
+LICENSE
+=======
+
+This program is free software; you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation; either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+SECTION 1: Introduction
+=======================
+
+Overview
+--------
+
+This document describes the hardware/software interface for the Rocker switch
+device.  The intended audience is authors of OS drivers and device emulation
+software.
+
+Notations and Conventions
+-------------------------
+
+o In register descriptions, [n:m] indicates a range from bit n to bit m,
+inclusive.
+o Use of leading 0x indicates a hexadecimal number.
+o Use of leading 0b indicates a binary number.
+o The use of RSVD or Reserved indicates that a bit or field is reserved for
+future use.
+o Field width is in bytes, unless otherwise noted.
+o Register are (R) read-only, (R/W) read/write, (W) write-only, or (COR) clear
+on read
+o TLV values in network-byte-order are designated with (N).
+
+
+SECTION 2: PCI Configuration Registers
+======================================
+
+PCI Configuration Space
+-----------------------
+
+Each switch instance registers as a PCI device with PCI configuration space:
+
+	offset	width	description		value
+	---------------------------------------------
+	0x0	2	Vendor ID		0x1b36
+	0x2	2	Device ID		0x0006
+	0x4	4	Command/Status
+	0x8	1	Revision ID		0x01
+	0x9	3	Class code		0x2800
+	0xC	1	Cache line size
+	0xD	1	Latency timer
+	0xE	1	Header type
+	0xF	1	Built-in self test
+	0x10	4	Base address low
+	0x14	4	Base address high
+	0x18-28		Reserved
+	0x2C	2	Subsystem vendor ID	*
+	0x2E	2	Subsystem ID		*
+	0x30-38		Reserved
+	0x3C	1	Interrupt line
+	0x3D	1	Interrupt pin		0x00
+	0x3E	1	Min grant		0x00
+	0x3D	1	Max latency		0x00
+	0x40	1	TRDY timeout
+	0x41	1	Retry count
+	0x42	2	Reserved
+
+
+* Assigned by sub-system implementation
+
+SECTION 3: Memory-Mapped Register Space
+=======================================
+
+There are two memory-mapped BARs.  BAR0 maps device register space and is
+0x2000 in size.  BAR1 maps MSI-X vector and PBA tables and is also 0x2000 in
+size, allowing for 256 MSI-X vectors.
+
+All registers are 4 or 8 bytes long.  It is assumed host software will access 4
+byte registers with one 4-byte access, and 8 byte registers with either two
+4-byte accesses or a single 8-byte access.  In the case of two 4-byte accesses,
+access must be lower and then upper 4-bytes, in that order.
+
+BAR0 device register space is organized as follows:
+
+	offset		description
+	------------------------------------------------------
+	0x0000-0x000f	Bogus registers to catch misbehaving
+			drivers.  Writes do nothing.  Reads
+			back as 0xDEADBABE.
+	0x0010-0x00ff	Test registers
+	0x0300-0x03ff	General purpose registers
+	0x1000-0x1fff	Descriptor control
+
+Holes in register space are reserved.  Writes to reserved registers do nothing.
+Reads to reserved registers read back as 0.
+
+No fancy stuff like write-combining is enabled on any of the registers.
+
+BAR1 MSI-X register space is organized as follows:
+
+	offset		description
+	------------------------------------------------------
+	0x0000-0x0fff	MSI-X vector table (256 vectors total)
+	0x1000-0x1fff	MSI-X PBA table
+
+
+SECTION 4: Interrupts, DMA, and Endianess
+=========================================
+
+PCI Interrupts
+--------------
+
+The device supports only MSI-X interrupts.  BAR1 memory-mapped region contains
+the MSI-X vector and PBA tables, with support for up to 256 MSI-X vectors.
+
+The vector assignment is:
+
+	vector		description
+	-----------------------------------------------------
+	0		Command descriptor ring completion
+	1		Event descriptor ring completion
+	2		Test operation completion
+	3		RSVD
+	4-255		Tx and Rx descriptor ring completion
+			  Tx vector is even
+			  Rx vector is odd
+
+A MSI-X vector table entry is 16 bytes:
+
+	field		offset	width	description
+	-------------------------------------------------------------
+	lower_addr	0x0	4	[31:2] message address[31:2]
+					[1:0] Rsvd (4 byte alignment
+						    required)
+	upper_addr	0x4	4	[31:19] Rsvd
+					[14:0] message address[46:32]
+	data		0x8	4	message data[31:0]
+	control		0xc	4	[31:1] Rsvd
+					[0] mask (0 = enable,
+						  1 = masked)
+
+Software should install the Interrupt Service Routine (ISR) before any ports
+are enabled or any commands are issued on the command ring.
+
+DMA Operations
+--------------
+
+DMA operations are used for packet DMA to/from the CPU, command and event
+processing.  Command processing includes statistical counters and table dumps,
+table insertion/deletion, and more.  Event processing provides an async
+notification method for device-originating events.  Each DMA operation has a
+set of control registers to manage a descriptor ring.  The descriptor rings are
+allocated from contiguous host DMA-able memory and registers specify the rings
+base address, size and current head and tail indices.  Software always writes
+the head, and hardware always writes the tail.
+
+The higher-order bit of DMA_DESC_COMP_ERR is used to mark hardware completion
+of a descriptor.  Software will clear this bit when posting a descriptor to the
+ring, and hardware will set this bit when the descriptor is complete.
+
+Descriptor ring sizes must be a power of 2 and range from 2 to 64K entries.
+Descriptor rings' base address must be 8-byte aligned.  Descriptors must be
+packed within ring.  Each descriptor in each ring must also be aligned on an 8
+byte boundary.  Each descriptor ring will have these registers:
+
+	DMA_DESC_xxx_BASE_ADDR, offset 0x1000 + (x * 32), 64-bit, (R/W)
+	DMA_DESC_xxx_SIZE, offset 0x1008 + (x * 32), 32-bit, (R/W)
+	DMA_DESC_xxx_HEAD, offset 0x100c + (x * 32), 32-bit, (R/W)
+	DMA_DESC_xxx_TAIL, offset 0x1010 + (x * 32), 32-bit, (R)
+	DMA_DESC_xxx_CTRL, offset 0x1014 + (x * 32), 32-bit, (W)
+	DMA_DESC_xxx_CREDITS, offset 0x1018 + (x * 32), 32-bit, (R/W)
+	DMA_DESC_xxx_RSVD1, offset 0x101c + (x * 32), 32-bit, (R/W)
+
+Where x is descriptor ring index:
+
+	index		ring
+	--------------------
+	0		CMD
+	1		EVENT
+	2		TX (port 0)
+	3		RX (port 0)
+	4		TX (port 1)
+	5		RX (port 1)
+	.
+	.
+	.
+	124		TX (port 61)
+	125		RX (port 61)
+	126		Resv
+	127		Resv
+
+Writing BASE_ADDR or SIZE will reset HEAD and TAIL to zero.  HEAD cannot be
+written passed TAIL.  To do so would wrap the ring.  An empty ring is when HEAD
+== TAIL.  A full ring is when HEAD is one position behind TAIL.  Both HEAD and
+TAIL increment and modulo wrap at the ring size.
+
+CTRL register bits:
+
+	bit	name		description
+	------------------------------------------------------------------------
+	[0]	CTRL_RESET	Reset the descriptor ring
+	[1:31]	Reserved
+
+All descriptor types share some common fields:
+
+	field			width	description
+	-------------------------------------------------------------------
+	DMA_DESC_BUF_ADDR	8	Phys addr of desc payload, 8-byte
+					aligned
+	DMA_DESC_COOKIE		8	Desc cookie for completion matching,
+					upper-most bit is reserved
+	DMA_DESC_BUF_SIZE	2	Desc payload size in bytes
+	DMA_DESC_TLV_SIZE	2	Desc payload total size in bytes
+					used for TLVs.  Must be <=
+					DMA_DESC_BUF_SIZE.
+	DMA_DESC_COMP_ERR	2	Completion status of associated
+					desc payload.  High order bit is
+					clear on new descs, toggled by
+					hw for completed items.
+
+To support forward- and backward-compatibility, descriptor and completion
+payloads are specified in TLV format.  Fields are packed with Type=field name,
+Length=field length, and Value=field value.  Software will ignore unknown fields
+filled in by the switch.  Likewise, the switch will ignore unknown fields
+filled in by software.
+
+Descriptor payload buffer is 8-byte aligned and TLVs are 8-byte aligned.  The
+value within a TLV is also 8-byte aligned.  The (packed, 8 byte) TLV header is:
+
+	field	width	description
+	-----------------------------
+	type	4	TLV type
+	len	2	TLV value length
+	pad	2	Reserved
+
+The alignment requirements for descriptors and TLVs are to avoid unaligned
+access exceptions in software.  Note that the payload for each TLV is also
+8 byte aligned.
+
+Figure 1 shows an example descriptor buffer with two TLVs.
+
+                  <------- 8 bytes ------->
+
+  8-byte  +––––+  +–––––––––––+–––––+–––––+                     +–+
+  align           |   type    | len | pad |    TLV#1 hdr          |
+                  +–––––––––––+–––––+–––––+    (len=22)           |
+                  |                       |                       |
+                  |  value                |    TVL#1 value        |
+                  |                       |    (padded to 8-byte  |
+                  |                 +–––––+     alignment)        |
+                  |                 |/////|                       |
+   8-byte +––––+  +–––––––––––+–––––––––––+                       |
+   align          |   type    | len | pad |    TLV#2 hdr    DESC_BUF_SIZE
+                  +–––––+–––––+–––––+–––––+    (len=2)            |
+                  |value|/////////////////|    TLV#2 value        |
+                  +–––––+/////////////////|                       |
+                  |///////////////////////|                       |
+                  |///////////////////////|                       |
+                  |///////////////////////|                       |
+                  |////////unused/////////|                       |
+                  |////////space//////////|                       |
+                  |///////////////////////|                       |
+                  |///////////////////////|                       |
+                  |///////////////////////|                       |
+                  +–––––––––––––––––––––––+                     +–+
+
+				fig. 1
+
+TLVs can be nested within the NEST TLV type.
+
+Interrupt credits
+^^^^^^^^^^^^^^^^^
+
+MSI-X vectors used for descriptor ring completions use a credit mechanism for
+efficient device, PCIe bus, OS and driver operations.  Each descriptor ring has
+a credit count which represent the number of outstanding descriptors to be
+processed by the driver.  As the device marks descriptors complete, the credit
+count is incremented.  As the driver processes those outstanding descriptors,
+it returns credits back to the device.  This way, the device knows the driver's
+progress and can make decisions about when to fire the next interrupt or not.
+When the credit count is zero, and the first descriptors are posted for the
+driver, a single interrupt is fired.  Once the interrupt is fired, the
+interrupt is disabled (auto-masked*).  In response to the interrupt, the driver
+will process descriptors and PIO write a returned credit value for that
+descriptor ring.  If the driver returns all credits (the driver caught up with
+the device and there is no outstanding work), then the interrupt is unmasked,
+but not fired.  If only partial credits are returned, the interrupt remains
+masked but the device generates an interrupt, signaling the driver that more
+outstanding work is available.
+
+(* this masking is unrelated to to the MSI-X interrupt mask register)
+
+Endianess
+---------
+
+Device registers are hard-coding to little-endian (LE).  The driver should
+convert to/from host endianess to LE for device register accesses.
+
+Descriptors are LE.  Descriptor buffer TLVs will have LE type and length
+fields, but the value field can either be LE or network-byte-order, depending
+on context.  TLV values containing network packet data will be in network-byte
+order.  A TLV value containing a field or mask used to compare against network
+packet data is network-byte order.  For example, flow match fields (and masks)
+are network-byte-order since they're matched directly, byte-by-byte, against
+network packet data.  All non-network-packet TLV multi-byte values will be LE.
+
+TLV values in network-byte-order are designated with (N).
+
+
+SECTION 5: Test Registers
+=========================
+
+Rocker has several test registers to support troubleshooting register access,
+interrupt generation, and DMA operations:
+
+	TEST_REG, offset 0x0010, 32-bit (R/W)
+	TEST_REG64, offset 0x0018, 64-bit (R/W)
+	TEST_IRQ, offset 0x0020, 32-bit (R/W)
+	TEST_DMA_ADDR, offset 0x0028, 64-bit (R/W)
+	TEST_DMA_SIZE, offset 0x0030, 32-bit (R/W)
+	TEST_DMA_CTRL, offset 0x0034, 32-bit (R/W)
+
+Reads to TEST_REG and TEST_REG64 will read a value equal to twice the last
+value written to the register.  The 32-bit and 64-bit versions are for testing
+32-bit and 64-bit host accesses.
+
+A vector can be written to TEST_IRQ and the device will generate an interrupt
+for that vector.
+
+To test basic DMA operations, allocate a DMA-able host buffer and put the
+buffer address into TEST_DMA_ADDR and size into TEST_DMA_SIZE.  Then, write to
+TEST_DMA_CTRL to manipulate the buffer contents.  TEST_DMA_CTRL operations are:
+
+	operation		value	description
+	-----------------------------------------------------------
+	TEST_DMA_CTRL_CLEAR	1	clear buffer
+	TEST_DMA_CTRL_FILL	2	fill buffer bytes with 0x96
+	TEST_DMA_CTRL_INVERT	4	invert bytes in buffer
+
+Various buffer address and sizes should be tested to verify no address boundary
+issue exists.  In particular, buffers that start on odd-8-byte boundary and/or
+span multiple PAGE sizes should be tested.
+
+
+SECTION 6: Ports
+================
+
+Physical and Logical Ports
+------------------------------------
+
+The switch supports up to 62 physical (front-panel) ports.  Register
+PORT_PHYS_COUNT returns the actual number of physical ports available:
+
+	PORT_PHYS_COUNT, offset 0x0304, 32-bit, (R)
+
+In addition to front-panel ports, the switch supports logical ports for
+tunnels.
+
+Front-panel ports and logical tunnel ports are mapped into a single 32-bit port
+space.  A special CPU port is assigned port 0.  The front-panel ports are
+mapped to ports 1-62.  A special loopback port is assigned port 63.  Logical
+tunnel ports are assigned ports 0x0001000-0x0001ffff.
+To summarize the port assignments:
+
+	port			mapping
+	-------------------------------------------------------
+	0			CPU port (for packets to/from host CPU)
+	1-62			front-panel physical ports
+	63			loopback port
+	64-0x0000ffff		RSVD
+	0x00010000-0x0001ffff	logical tunnel ports
+        0x00020000-0xffffffff   RSVD
+
+Physical Port Mode
+------------------
+
+Switch front-panel ports operate in a mode.  Current, only mode is OF-DPA.
+OF-DPA[1] mode is based on OpenFlow Data Plane Abstraction (OF-DPA) Abstract
+Switch Specification, Version 1.0, from Broadcom Corporation.  To set/get the
+mode for front-panel ports, see port settings, below.
+
+Port Settings
+-------------
+
+Links status for all front-panel ports is available via PORT_PHYS_LINK_STATUS:
+
+	PORT_PHYS_LINK_STATUS, offset 0x0310, 64-bit, (R)
+
+	Value is port bitmap.  Bits 0 and 63 always read 0.  Bits 1-62
+	read 1 for link UP and 0 for link DOWN for respective front-panel ports.
+
+Other properties for front-panel ports are available via DMA CMD descriptors:
+
+	Get PORT_SETTINGS descriptor:
+
+		field		width	description
+		----------------------------------------------
+		PORT_SETTINGS	2	CMD_GET
+		PPORT		4	Physical port #
+
+	Get PORT_SETTINGS completion:
+
+		field		width	description
+		----------------------------------------------
+		PPORT		4	Physical port #
+		SPEED		4	Current port interface speed, in Mbps
+		DUPLEX		1	1 = Full, 0 = Half
+		AUTONEG		1	1 = enabled, 0 = disabled
+		MACADDR		6	Port MAC address
+		MODE		1	0 = OF-DPA
+
+	Set PORT_SETTINGS descriptor:
+
+		field		width	description
+		----------------------------------------------
+		PORT_SETTINGS	2	CMD_SET
+		PPORT		4	Physical port #
+		SPEED		4	Port interface speed, in Mbps
+		DUPLEX		1	1 = Full, 0 = Half
+		AUTONEG		1	1 = enabled, 0 = disabled
+		MACADDR		6	Port MAC address
+		MODE		1	0 = OF-DPA
+
+Port Enable
+-----------
+
+Front-panel ports are initially disabled, which means port ingress and egress
+packets will be dropped.  To enable or disable a port, use PORT_PHYS_ENABLE:
+
+	PORT_PHYS_ENABLE: offset 0x0318, 64-bit, (R/W)
+
+	Value is bitmap of first 64 ports.  Bits 0 and 63 are ignored
+	and always read as 0.  Write 1 to enable port; write 0 to disable it.
+	Default is 0.
+
+SECTION 7: Switch Control
+=========================
+
+This section covers switch-wide register settings.
+
+Control
+-------
+
+This register is used for low level control of the switch.
+
+	CONTROL: offset 0x0300, 32-bit, (W)
+
+	bit	name		description
+	------------------------------------------------------------------------
+	[0]	CONTROL_RESET	If set, device will perform reset
+	[1:31]	Reserved
+
+Switch ID
+---------
+
+The switch has a SWITCH_ID to be used by software to uniquely identify the
+switch:
+
+	SWITCH_ID: offset 0x0320, 64-bit, (R)
+
+	Value is opaque to switch software and no special encoding is implied.
+
+
+SECTION 8: CPU Packet Processing
+================================
+
+Ingress packets directed to the host CPU for further processing are delivered
+in the DMA RX ring.  Likewise, host CPU originating packets destined to egress
+on switch ports are scheduled by software using the DMA TX ring.
+
+Tx Packet Processing
+--------------------
+
+Software schedules packets for egress on switch ports using the DMA TX ring.  A
+TX descriptor buffer describes the packet location and size in host DMA-able
+memory, the destination port, and any hardware-offload functions (such as L3
+payload checksum offload).  Software then bumps the descriptor head to signal
+hardware of new Tx work.  In response, hardware will DMA read Tx descriptors up
+to head, DMA read descriptor buffer and packet data, perform offloading
+functions, and finally frame packet on wire (network).  Once packet processing
+is complete, hardware will writeback status to descriptor(s) to signal to
+software that Tx is complete and software resources (e.g. skb) backing packet
+can be released.
+
+Figure 2 shows an example 3-fragment packet queued with one Tx descriptor.  A
+TLV is used for each packet fragment.
+
+	                                           pkt frag 1
+	                                           +–––––––+  +–+
+	                                       +–––+       |    |
+	                         desc buf      |   |       |    |
+	                        +––––––––+     |   |       |    |
+	        Tx ring     +–––+        +–––––+   |       |    |
+	      +–––––––––+   |   |  TLVs  |         +–––––––+    |
+	      |         +–––+   +––––––––+         pkt frag 2   |
+	      | desc 0  |       |        +–––––+   +–––––––+    |
+	      +–––––––––+       |  TLVs  |     +–––+       |    |
+	head+–+         |       +––––––––+         |       |    |
+	      | desc 1  |       |        +–––––+   +–––––––+    |pkt
+	      +–––––––––+       |  TLVs  |     |                |
+	      |         |       +––––––––+     |   pkt frag 3   |
+	      |         |                      |   +–––––––+    |
+	      +–––––––––+                      +–––+       |    |
+	      |         |                          |       |    |
+	      |         |                          |       |    |
+	      +–––––––––+                          |       |    |
+	      |         |                          |       |    |
+	      |         |                          |       |    |
+	      +–––––––––+                          |       |    |
+	      |         |                          +–––––––+  +–+
+	      |         |
+	      +–––––––––+
+
+				fig 2.
+
+The TLVs for Tx descriptor buffer are:
+
+	field			width	description
+	---------------------------------------------------------------------
+	PPORT			4	Destination physical port #
+	TX_OFFLOAD		1	Hardware offload modes:
+					  0: no offload
+					  1: insert IP csum (ipv4 only)
+					  2: insert TCP/UDP csum
+					  3: L3 csum calc and insert
+                        	             into csum offset (TX_L3_CSUM_OFF)
+                 	                    16-bit 1's complement csum value.
+                                	     IPv4 pseudo-header and IP
+                        	             already calculated by OS
+                  	                   and inserted.
+					  4: TSO (TCP Segmentation Offload)
+	TX_L3_CSUM_OFF		2	For L3 csum offload mode, the offset,
+					from the beginning of the packet,
+					of the csum field in the L3 header
+	TX_TSO_MSS		2	For TSO offload mode, the
+					Maximum Segment Size in bytes
+        TX_TSO_HDR_LEN		2	For TSO offload mode, the
+					length of ethernet, IP, and
+					TCP/UDP headers, including IP
+					and TCP options.
+	TX_FRAGS		<array>	Packet fragments
+	  TX_FRAG		<nest>	Packet fragment
+	    TX_FRAG_ADDR	8	DMA address of packet fragment
+	    TX_FRAG_LEN		2	Packet fragment length
+
+Possible status return codes in descriptor on completion are:
+
+	DESC_COMP_ERR	reason
+	--------------------------------------------------------------------
+	0		OK
+	-ROCKER_ENXIO	address or data read err on desc buf or packet
+			fragment
+	-ROCKER_EINVAL	bad pport or TSO or csum offloading error
+	-ROCKER_ENOMEM	no memory for internal staging tx fragment
+
+Rx Packet Processing
+--------------------
+
+For packets ingressing on switch ports that are not forwarded by the switch but
+rather directed to the host CPU for further processing are delivered in the
+DMA RX ring.  Rx descriptor buffers are allocated by software and placed on the
+ring.  Hardware will fill Rx descriptor buffers with packet data, write the
+completion, and signal to software that a new packet is ready.  Since Rx packet
+size is not known a-priori, the Rx descriptor buffer must be allocated for
+worst-case packet size.  A single Rx descriptor will contain the entire Rx
+packet data in one RX_PACKET TLV.  Other Rx TLVs describe and hardware offloads
+performed on the packet, such as checksum validation.
+
+The TLVs for Rx descriptor buffer are:
+
+	field		width	description
+	---------------------------------------------------
+	PPORT		4	Source physical port #
+	RX_FLAGS	2	Packet parsing flags:
+				  (1 << 0): IPv4 packet
+				  (1 << 1): IPv6 packet
+				  (1 << 2): csum calculated
+				  (1 << 3): IPv4 csum good
+				  (1 << 4): IP fragment
+				  (1 << 5): TCP packet
+				  (1 << 6): UDP packet
+				  (1 << 7): TCP/UDP csum good
+	RX_CSUM		2	IP calculated checksum:
+				  IPv4: IP payload csum
+				  IPv6: header and payload csum
+				(Only valid is RX_FLAGS:csum calc is set)
+	RX_PACKET (N)	<var>	Packet data
+
+Possible status return codes in descriptor on completion are:
+
+	DESC_COMP_ERR	reason
+	--------------------------------------------------------------------
+	0		OK
+	-ROCKER_ENXIO	address or data read err on desc buf
+	-ROCKER_ENOMEM	no memory for internal staging desc buf
+	-ROCKER_EMSGSIZE Rx descriptor buffer wasn't big enough to contain
+			pactet data TLV and other TLVs.
+
+
+SECTION 9: OF-DPA Mode
+======================
+
+OF-DPA mode allows the switch to offload flow packet processing functions to
+hardware.  An OpenFlow controller would communicate with an OpenFlow agent
+installed on the switch.  The OpenFlow agent would (directly or indirectly)
+communicate with the Rocker switch driver, which in turn would program switch
+hardware with flow functionality, as defined in OF-DPA.  The block diagram is:
+
+		+–––––––––––––––----–––+
+		|        OF            |
+		|  Remote Controller   |
+		+––––––––+––----–––––––+
+		         |
+		         |
+		+––––––––+–––––––––+
+		|       OF         |
+		|   Local Agent    |
+		+––––––––––––––––––+
+		|                  |
+		|   Rocker Driver  |
+		+––––––––––––––––––+
+		    <this spec>
+		+––––––––––––––––––+
+		|                  |
+		|   Rocker Switch  |
+		+––––––––––––––––––+
+
+To participate in flow functions, ports must be configure for OF-DPA mode
+during switch initialization.
+
+OF-DPA Flow Table Interface
+---------------------------
+
+There are commands to add, modify, delete, and get stats of flow table entries.
+The commands are issued using the DMA CMD descriptor ring.  The following
+commands are defined:
+
+	CMD_ADD:		add an entry to flow table
+	CMD_MOD:		modify an entry in flow table
+	CMD_DEL:		delete an entry from flow table
+	CMD_GET_STATS:		get stats for flow entry
+
+TLVs for add and modify commands are:
+
+	field			width	description
+	----------------------------------------------------
+	OF_DPA_CMD		2	CMD_[ADD|MOD]
+	OF_DPA_TBL		2	Flow table ID
+					  0: ingress port
+					  10: vlan
+					  20: termination mac
+					  30: unicast routing
+					  40: multicast routing
+					  50: bridging
+					  60: ACL policy
+	OF_DPA_PRIORITY		4	Flow priority
+	OF_DPA_HARDTIME		4	Hard timeout for flow
+	OF_DPA_IDLETIME		4	Idle timeout for flow
+	OF_DPA_COOKIE		8	Cookie
+
+Additional TLVs based on flow table ID:
+
+Table ID 0: ingress port
+
+	field			width	description
+	----------------------------------------------------
+	OF_DPA_IN_PPORT		4	ingress physical port number
+	OF_DPA_GOTO_TBL		2	goto table ID; zero to drop
+
+Table ID 10: vlan
+
+	field			width	description
+	----------------------------------------------------
+	OF_DPA_IN_PPORT		4	ingress physical port number
+	OF_DPA_VLAN_ID		2 (N)	vlan ID
+	OF_DPA_VLAN_ID_MASK	2 (N)	vlan ID mask
+	OF_DPA_GOTO_TBL		2	goto table ID; zero to drop
+	OF_DPA_NEW_VLAN_ID	2 (N)	new vlan ID
+
+Table ID 20: termination mac
+
+	field			width	description
+	----------------------------------------------------
+	OF_DPA_IN_PPORT		4	ingress physical port number
+	OF_DPA_IN_PPORT_MASK	4	ingress physical port number mask
+	OF_DPA_ETHERTYPE	2 (N)	must be either 0x0800 or 0x86dd
+	OF_DPA_DST_MAC		6 (N)	destination MAC
+	OF_DPA_DST_MAC_MASK	6 (N)	destination MAC mask
+	OF_DPA_VLAN_ID		2 (N)	vlan ID
+	OF_DPA_VLAN_ID_MASK	2 (N)	vlan ID mask
+	OF_DPA_GOTO_TBL		2	only acceptable values are
+					unicast or multicast routing
+					table IDs
+	OF_DPA_OUT_PPORT	2	if specified, must be
+					controller, set zero otherwise
+
+Table ID 30: unicast routing
+
+	field			width	description
+	----------------------------------------------------
+	OF_DPA_ETHERTYPE	2 (N)	must be either 0x0800 or 0x86dd
+	OF_DPA_DST_IP		4 (N)	destination IPv4 address.
+					Must be unicast address
+	OF_DPA_DST_IP_MASK	4 (N)	IP mask.  Must be prefix mask
+	OF_DPA_DST_IPV6		16 (N)	destination IPv6 address.
+					Must be unicast address
+	OF_DPA_DST_IPV6_MASK	16 (N)	IPv6 mask. Must be prefix mask
+	OF_DPA_GOTO_TBL		2	goto table ID; zero to drop
+	OF_DPA_GROUP_ID		4	data for GROUP action must
+					be an L3 Unicast group entry
+
+Table ID 40: multicast routing
+
+	field			width	description
+	----------------------------------------------------
+	OF_DPA_ETHERTYPE	2 (N)	must be either 0x0800 or 0x86dd
+	OF_DPA_VLAN_ID		2 (N)	vlan ID
+	OF_DPA_SRC_IP		4 (N)	source IPv4. Optional,
+					can contain IPv4 address,
+					must be completely masked
+					if not used
+	OF_DPA_SRC_IP_MASK	4 (N)	IP Mask
+	OF_DPA_DST_IP		4 (N)	destination IPv4 address.
+					Must be multicast address
+	OF_DPA_SRC_IPV6		16 (N)	source IPv6 Address. Optional.
+					Can contain IPv6 address,
+					must be completely masked
+					if not used
+	OF_DPA_SRC_IPV6_MASK	16 (N)	IPv6 mask.
+	OF_DPA_DST_IPV6		16 (N)	destination IPv6 Address. Must
+					be multicast address
+					Must be multicast address
+	OF_DPA_GOTO_TBL		2	goto table ID; zero to drop
+	OF_DPA_GROUP_ID		4	data for GROUP action must
+					be an L3 multicast group entry
+
+Table ID 50: bridging
+
+	field			width	description
+	----------------------------------------------------
+	OF_DPA_VLAN_ID		2 (N)	vlan ID
+	OF_DPA_TUNNEL_ID	4	tunnel ID
+	OF_DPA_DST_MAC		6 (N)	destination MAC
+	OF_DPA_DST_MAC_MASK	6 (N)	destination MAC mask
+	OF_DPA_GOTO_TBL		2	goto table ID; zero to drop
+	OF_DPA_GROUP_ID		4	data for GROUP action must
+					be a L2 Interface, L2
+					Multicast, L2 Flood,
+					or L2 Overlay group entry
+					as appropriate
+	OF_DPA_TUNNEL_LPORT	4	unicast Tenant Bridging
+					flows specify a tunnel
+					logical port ID
+	OF_DPA_OUT_PPORT	2	data for OUTPUT action,
+					restricted to CONTROLLER,
+					set to 0 otherwise
+
+Table ID 60: acl policy
+
+	field			width	description
+	----------------------------------------------------
+	OF_DPA_IN_PPORT		4	ingress physical port number
+	OF_DPA_IN_PPORT_MASK	4	ingress physical port number mask
+	OF_DPA_ETHERTYPE	2 (N)	ethertype
+	OF_DPA_VLAN_ID		2 (N)	vlan ID
+	OF_DPA_VLAN_ID_MASK	2 (N)	vlan ID mask
+	OF_DPA_VLAN_PCP		2 (N)	vlan Priority Code Point
+	OF_DPA_VLAN_PCP_MASK	2 (N)	vlan Priority Code Point mask
+	OF_DPA_SRC_MAC		6 (N)	source MAC
+	OF_DPA_SRC_MAC_MASK	6 (N)	source MAC mask
+	OF_DPA_DST_MAC		6 (N)	destination MAC
+	OF_DPA_DST_MAC_MASK	6 (N)	destination MAC mask
+	OF_DPA_TUNNEL_ID	4	tunnel ID
+	OF_DPA_SRC_IP		4 (N)	source IPv4. Optional,
+					can contain IPv4 address,
+					must be completely masked
+					if not used
+	OF_DPA_SRC_IP_MASK	4 (N)	IP Mask
+	OF_DPA_DST_IP		4 (N)	destination IPv4 address.
+					Must be multicast address
+	OF_DPA_DST_IP_MASK	4 (N)	IP Mask
+	OF_DPA_SRC_IPV6		16 (N)	source IPv6 Address. Optional.
+					Can contain IPv6 address,
+					must be completely masked
+					if not used
+	OF_DPA_SRC_IPV6_MASK	16 (N)	IPv6 mask
+	OF_DPA_DST_IPV6		16 (N)	destination IPv6 Address. Must
+					be multicast address.
+	OF_DPA_DST_IPV6_MASK	16 (N)	IPv6 mask
+	OF_DPA_SRC_ARP_IP	4 (N)	source IPv4 address in the ARP
+					payload.  Only used if ethertype
+					== 0x0806.
+	OF_DPA_SRC_ARP_IP_MASK	4 (N)	IP Mask
+	OF_DPA_IP_PROTO		1	IP protocol
+	OF_DPA_IP_PROTO_MASK	1	IP protocol mask
+	OF_DPA_IP_DSCP		1	DSCP
+	OF_DPA_IP_DSCP_MASK	1	DSCP mask
+	OF_DPA_IP_ECN		1	ECN
+	OF_DPA_IP_ECN_MASK		1	ECN mask
+	OF_DPA_L4_SRC_PORT	2 (N)	L4 source port, only for
+					TCP, UDP, or SCTP
+	OF_DPA_L4_SRC_PORT_MASK	2 (N)	L4 source port mask
+	OF_DPA_L4_DST_PORT	2 (N)	L4 source port, only for
+					TCP, UDP, or SCTP
+	OF_DPA_L4_DST_PORT_MASK	2 (N)	L4 source port mask
+	OF_DPA_ICMP_TYPE	1	ICMP type, only if IP
+					protocol is 1
+	OF_DPA_ICMP_TYPE_MASK	1	ICMP type mask
+	OF_DPA_ICMP_CODE	1	ICMP code
+	OF_DPA_ICMP_CODE_MASK	1	ICMP code mask
+	OF_DPA_IPV6_LABEL	4 (N)	IPv6 flow label
+	OF_DPA_IPV6_LABEL_MASK	4 (N)	IPv6 flow label mask
+	OF_DPA_GROUP_ID		4	data for GROUP action
+	OF_DPA_QUEUE_ID_ACTION	1	write the queue ID
+	OF_DPA_NEW_QUEUE_ID	1	queue ID
+	OF_DPA_VLAN_PCP_ACTION	1	write the VLAN priority
+	OF_DPA_NEW_VLAN_PCP	1	VLAN priority
+	OF_DPA_IP_DSCP_ACTION	1	write the DSCP
+	OF_DPA_NEW_IP_DSCP	1	new DSCP
+	OF_DPA_TUNNEL_LPORT	4	restrct to valid tunnel
+					logical port, set to 0
+					otherwise.
+	OF_DPA_OUT_PPORT	2	data for OUTPUT action,
+					restricted to CONTROLLER,
+					set to 0 otherwise
+	OF_DPA_CLEAR_ACTIONS	4	if 1 packets matching flow are
+					dropped (all other instructions
+					ignored)
+
+TLVs for flow delete and get stats command are:
+
+	field			width	description
+	---------------------------------------------------
+	OF_DPA_CMD		2	CMD_[DEL|GET_STATS]
+	OF_DPA_COOKIE		8	Cookie
+
+On completion of get stats command, the descriptor buffer is written back with
+the following TLVs:
+
+	field			width	description
+	---------------------------------------------------
+	OF_DPA_STAT_DURATION	4	Flow duration
+	OF_DPA_STAT_RX_PKTS	8	Received packets
+	OF_DPA_STAT_TX_PKTS	8	Transmit packets
+
+Possible status return codes in descriptor on completion are:
+
+	DESC_COMP_ERR	command			reason
+	--------------------------------------------------------------------
+	0		all			OK
+	-ROCKER_EFAULT	all			head or tail index outside
+						of ring
+	-ROCKER_ENXIO	all			address or data read err on
+						desc buf
+	-ROCKER_EMSGSIZE GET_STATS		cmd descriptor buffer wasn't
+						big enough to contain write-back
+						TLVs
+	-ROCKER_EINVAL	all			invalid parameters passed in
+	-ROCKER_EEXIST	ADD			entry already exists
+	-ROCKER_ENOSPC	ADD			no space left in flow table
+	-ROCKER_ENOENT	MOD|DEL|GET_STATS	cookie invalid
+
+Group Table Interface
+---------------------
+
+There are commands to add, modify, delete, and get stats of group table
+entries.  The commands are issued using the DMA CMD descriptor ring.  The
+following commands are defined:
+
+	CMD_ADD:		add an entry to group table
+	CMD_MOD:		modify an entry in group table
+	CMD_DEL:		delete an entry from group table
+	CMD_GET_STATS:		get stats for group entry
+
+TLVs for add and modify commands are:
+
+	field			width	description
+	-----------------------------------------------------------
+	FLOW_GROUP_CMD		2	CMD_[ADD|MOD]
+	FLOW_GROUP_ID		2	Flow group ID
+	FLOW_GROUP_TYPE		1	Group type:
+					  0: L2 interface
+					  1: L2 rewrite
+					  2: L3 unicast
+					  3: L2 multicast
+					  4: L2 flood
+					  5: L3 interface
+					  6: L3 multicast
+					  7: L3 ECMP
+					  8: L2 overlay
+	FLOW_VLAN_ID		2	Vlan ID (types 0, 3, 4, 6)
+	FLOW_L2_PORT		2	Port (types 0)
+	FLOW_INDEX		4	Index (all types but 0)
+	FLOW_OVERLAY_TYPE	1	Overlay sub-type (type 8):
+					  0: Flood unicast tunnel
+					  1: Flood multicast tunnel
+					  2: Multicast unicast tunnel
+					  3: Multicast multicast tunnel
+	FLOW_GROUP_ACTION		nest
+	  FLOW_GROUP_ID		2	next group ID in chain (all
+					types except 0)
+	  FLOW_OUT_PORT		4	egress port (types 0, 8)
+	  FLOW_POP_VLAN_TAG	1	strip outer VLAN tag (type 1
+					only)
+	  FLOW_VLAN_ID		2	(types 1, 5)
+	  FLOW_SRC_MAC		6	(types 1, 2, 5)
+	  FLOW_DST_MAC		6	(types 1, 2)
+
+TLVs for flow delete and get stats command are:
+
+	field			width	description
+	-----------------------------------------------------------
+	FLOW_GROUP_CMD		2	CMD_[DEL|GET_STATS]
+	FLOW_GROUP_ID		2	Flow group ID
+
+On completion of get stats command, the descriptor buffer is written back with
+the following TLVs:
+
+	field			width	description
+	---------------------------------------------------
+	FLOW_GROUP_ID		2	Flow group ID
+	FLOW_STAT_DURATION	4	Flow duration
+	FLOW_STAT_REF_COUNT	4	Flow reference count
+	FLOW_STAT_BUCKET_COUNT	4	Flow bucket count
+
+Possible status return codes in descriptor on completion are:
+
+	DESC_COMP_ERR	command			reason
+	--------------------------------------------------------------------
+	0		all			OK
+	-ROCKER_EFAULT	all			head or tail index outside
+						of ring
+	-ROCKER_ENXIO	all			address or data read err on
+						desc buf
+	-ROCKER_ENOSPC	GET_STATS		cmd descriptor buffer wasn't
+						big enough to contain write-back
+						TLVs
+	-ROCKER_EINVAL	ADD|MOD			invalid parameters passed in
+	-ROCKER_EEXIST	ADD			entry already exists
+	-ROCKER_ENOSPC	ADD			no space left in flow table
+	-ROCKER_ENOENT	MOD|DEL|GET_STATS	group ID invalid
+	-ROCKER_EBUSY	DEL			group reference count non-zero
+	-ROCKER_ENODEV	ADD			next group ID doesn't exist
+
+
+
+References
+==========
+
+[1] OpenFlow Data Plane Abstraction (OF-DPA) Abstract Switch Specification,
+Version 1.0, from Broadcom Corporation, February 21, 2014.

index c6732fe..e4a4490 100644
@@ -45,6 +45,7 @@ PCI devices (other than virtio):
 1b36:0003  PCI Dual-port 16550A adapter (docs/specs/pci-serial.txt)
 1b36:0004  PCI Quad-port 16550A adapter (docs/specs/pci-serial.txt)
 1b36:0005  PCI test device (docs/specs/pci-testdev.txt)
+1b36:0006  PCI Rocker Ethernet switch device
 1b36:0007  PCI SD Card Host Controller Interface (SDHCI)
 
 All these devices are documented in docs/specs.

index a186c39..a7f3278 100644
@@ -32,3 +32,4 @@ CONFIG_PCI_TESTDEV=y
 CONFIG_NVME_PCI=y
 CONFIG_SD=y
 CONFIG_SDHCI=y
+CONFIG_ROCKER=y

index ea93293..4f8e826 100644
@@ -35,3 +35,6 @@ obj-y += vhost_net.o
 
 obj-$(CONFIG_ETSEC) += fsl_etsec/etsec.o fsl_etsec/registers.o \
 			fsl_etsec/rings.o fsl_etsec/miim.o
+
+common-obj-y += rocker/rocker.o rocker/rocker_fp.o rocker/rocker_desc.o \
+                        rocker/rocker_world.o rocker/rocker_of_dpa.o

index e37bc8b..6873a3a 100644
@@ -1787,5 +1787,29 @@ show available trace events and their state
 ETEXI
 
 STEXI
+@item rocker @var{name}
+@findex rocker
+Show Rocker(s)
+ETEXI
+
+STEXI
+@item rocker_ports @var{name}
+@findex rocker_ports
+Show Rocker ports
+ETEXI
+
+STEXI
+@item rocker_of_dpa_flows @var{name} [@var{tbl_id}]
+@findex rocker_of_dpa_flows
+Show Rocker OF-DPA flow tables
+ETEXI
+
+STEXI
+@item rocker_of_dpa_groups @var{name} [@var{type}]
+@findex rocker_of_dpa_groups
+Show Rocker OF-DPA groups
+ETEXI
+
+STEXI
 @end table
 ETEXI

index fbfc52f..c6d04ca 100644
@@ -3523,3 +3523,6 @@
 # Since: 2.1
 ##
 { 'command': 'rtc-reset-reinjection' }
+
+# Rocker ethernet network switch
+{ 'include': 'qapi/rocker.json' }

259 lines not on this page · raw message

100 lines not on this page · raw message

new file mode 100644
index 0000000..531e673
@@ -0,0 +1,5 @@
+Tests require simp (simple network simulator) found here:
+
+https://github.com/scottfeldman/simp
+
+Run 'all' to run all tests.

new file mode 100755
index 0000000..d5ae963
@@ -0,0 +1,19 @@
+echo -n "Running port test...              "
+./port
+if [ $? -eq 0 ]; then echo "pass"; else echo "FAILED"; exit 1; fi
+
+echo -n "Running bridge test...            "
+./bridge
+if [ $? -eq 0 ]; then echo "pass"; else echo "FAILED"; exit 1; fi
+
+echo -n "Running bridge STP test...        "
+./bridge-stp
+if [ $? -eq 0 ]; then echo "pass"; else echo "FAILED"; exit 1; fi
+
+echo -n "Running bridge VLAN test...       "
+./bridge-vlan
+if [ $? -eq 0 ]; then echo "pass"; else echo "FAILED"; exit 1; fi
+
+echo -n "Running bridge VLAN STP test...   "
+./bridge-vlan-stp
+if [ $? -eq 0 ]; then echo "pass"; else echo "FAILED"; exit 1; fi

43 lines not on this page · raw message

52 lines not on this page · raw message

52 lines not on this page · raw message

64 lines not on this page · raw message

new file mode 100755
index 0000000..3437f7d
@@ -0,0 +1,22 @@
+simp destroy ".*"
+simp create -o sw1:rocker:sw1 tut tut.dot
+simp start tut
+while ! simp ssh tut sw1 --cmd "ping -c 1 localhost >/dev/null"; do sleep 1; done
+while ! simp ssh tut h1 --cmd "ping -c 1 localhost >/dev/null"; do sleep 1; done
+while ! simp ssh tut h2 --cmd "ping -c 1 localhost >/dev/null"; do sleep 1; done
+
+# bring up DUT ports
+
+simp ssh tut sw1 --cmd "sudo ifconfig swp1 11.0.0.1/24"
+simp ssh tut sw1 --cmd "sudo ifconfig swp2 12.0.0.1/24"
+
+# config IP on hosts
+
+simp ssh tut h1 --cmd "sudo ifconfig swp1 11.0.0.2/24"
+simp ssh tut h2 --cmd "sudo ifconfig swp1 12.0.0.2/24"
+
+# test...
+
+simp ssh tut h1 --cmd "ping -c10 11.0.0.1 >/dev/null"
+if [ $? -eq 1 ]; then exit 1; fi
+simp ssh tut h2 --cmd "ping -c10 12.0.0.1 >/dev/null"

new file mode 100644
index 0000000..87f7266
@@ -0,0 +1,8 @@
+graph G {
+	graph [hostidtype="hostname", version="1:0", date="04/12/2013"];
+	edge [dir=none, notify="log"];
+	sw1:swp1 -- h1:swp1;
+	sw1:swp2 -- h2:swp1;
+	sw1:swp3 -- h3:swp1;
+	sw1:swp4 -- h4:swp1;
+}

index 430688d..8b6f8d4 100644
@@ -736,6 +736,12 @@ S: Maintained
 F: hw/net/vmxnet*
 F: hw/scsi/vmw_pvscsi*
 
+Rocker
+M: Scott Feldman <[email protected]>
+M: Jiri Pirko <[email protected]>
+S: Maintained
+F: hw/net/rocker/
+
 Subsystems
 ----------
 Audio