x86: New Intel Quark SoC support
v3 cover x86: New Intel Quark SoC support
This series adds the first step of bare support for the Intel Quark SoC support which can be validated on Intel Galileo board.
Intel Quark is a line of 32-bit x86 SoCs by Intel, designed for small size and low power consumption, and targeted at new markets including wearable devices. They are smaller and slower than Atom processors and consume less power. They lack support for SIMD instruction sets (such as MMX and SSE) and only support embedded operating systems. Quark powers the Intel Galileo developer microcontroller board. The CPU instruction set is the same as Pentium (P54C/i586) CPU.
Intel decided to completely publish Quark's hardware specification to software developers, which includes an SoC datasheet, a UEFI Firmware Writer's Guide, and a complete reference source code for the UEFI BIOS which is pre-flahsed on the Galileo board. As of today, the only BIOS for Galileo is the Intel one with UEFI inteface only. There is no CSM support yet in that BIOS, neither any 3rd party BIOS vendor provides support to Quark SoC.
Only one binary blob (exactly 8KiB) is needed which is rmu.bin for Remote Management Unit. Not like FSP, U-Boot will not call into the binary. The binary is needed by the Quark SoC itself.
Note there are two generation of Galileo boards, aka gen1 and gen2. Currently the development work is on gen2, but once we get it boot, we can easily add the gen1 board (old version).
With this patch series, the generated u-boot.rom could boot the Intel Galileo board up to fdt relocate, where U-Boot hangs because the DRAM is not initializaed yet. A follow up patch series will be sent soon to add support for Memory Reference Code (MRC).
Changes in v3:
- Add several macros for message bus port and registers
- Use lower case hex
- New patch to define macros for pci configuration space access
- Use macros from <asm/pci.h> and <asm/arch/quark.h>
- Add simple help for ACPI PM1, PBLK and GEP0
Changes in v2:
- Rebase to u-boot-86/master
- Add msg_port_setup() and remove MCR_FILL
- Add MSG_BYTE_ENABLE define
- Wrap function declaraion with __ASSEMBLY__
- Replace upper case register names (EAX etc.) with lower case
- Use some macros from <asm/arch/msg_port.h> and <asm/arch/quark.h>
- Use machine-specific
- Move vairous components' base addresses within Quark SoC to Kconfig
- Use Arduino-certified
Bin Meng (7):
x86: Add header files for Intel Quark SoC defines
x86: quark: Add routines to access message bus registers
x86: Define macros for pci configuration space access
x86: quark: Add Cache-As-RAM initialization
x86: Add basic Intel Quark processor support
x86: Add basic Intel Galileo board support
x86: Enable the Intel quark/galileo build
arch/x86/Kconfig | 17 ++++ arch/x86/cpu/Makefile | 1 + arch/x86/cpu/quark/Kconfig | 121 +++++++++++++++++++++++++++++ arch/x86/cpu/quark/Makefile | 8 ++ arch/x86/cpu/quark/car.S | 105 +++++++++++++++++++++++++ arch/x86/cpu/quark/dram.c | 39 ++++++++++ arch/x86/cpu/quark/msg_port.c | 77 ++++++++++++++++++ arch/x86/cpu/quark/pci.c | 70 +++++++++++++++++ arch/x86/cpu/quark/quark.c | 44 +++++++++++ arch/x86/dts/Makefile | 1 + arch/x86/dts/galileo.dts | 43 ++++++++++ arch/x86/include/asm/arch-quark/device.h | 28 +++++++ arch/x86/include/asm/arch-quark/gpio.h | 13 ++++ arch/x86/include/asm/arch-quark/msg_port.h | 106 +++++++++++++++++++++++++ arch/x86/include/asm/arch-quark/quark.h | 40 ++++++++++ arch/x86/include/asm/pci.h | 13 +++- arch/x86/lib/pci_type1.c | 7 +- board/intel/galileo/Kconfig | 21 +++++ board/intel/galileo/MAINTAINERS | 6 ++ board/intel/galileo/Makefile | 7 ++ board/intel/galileo/galileo.c | 19 +++++ board/intel/galileo/start.S | 9 +++ configs/galileo_defconfig | 6 ++ include/configs/galileo.h | 53 +++++++++++++ 24 files changed, 847 insertions(+), 7 deletions(-) create mode 100644 arch/x86/cpu/quark/Kconfig create mode 100644 arch/x86/cpu/quark/Makefile create mode 100644 arch/x86/cpu/quark/car.S create mode 100644 arch/x86/cpu/quark/dram.c create mode 100644 arch/x86/cpu/quark/msg_port.c create mode 100644 arch/x86/cpu/quark/pci.c create mode 100644 arch/x86/cpu/quark/quark.c create mode 100644 arch/x86/dts/galileo.dts create mode 100644 arch/x86/include/asm/arch-quark/device.h create mode 100644 arch/x86/include/asm/arch-quark/gpio.h create mode 100644 arch/x86/include/asm/arch-quark/msg_port.h create mode 100644 arch/x86/include/asm/arch-quark/quark.h create mode 100644 board/intel/galileo/Kconfig create mode 100644 board/intel/galileo/MAINTAINERS create mode 100644 board/intel/galileo/Makefile create mode 100644 board/intel/galileo/galileo.c create mode 100644 board/intel/galileo/start.S create mode 100644 configs/galileo_defconfig create mode 100644 include/configs/galileo.h
Signature · 1 line
1.8.2.1
RFC PATCH v3 1/7 x86: Add header files for Intel Quark SoC defines
device.h for integrated pci devices' bdf on Quark SoC and quark.h for various memory-mapped and i/o-mapped base addresses within SoC.
---
Changes in v3:
- Add several macros for message bus port and registers
Changes in v2:
- Move vairous components' base addresses within Quark SoC to Kconfig
arch/x86/include/asm/arch-quark/device.h | 28 ++++++++++++++++++++++ arch/x86/include/asm/arch-quark/quark.h | 40 ++++++++++++++++++++++++++++++++ 2 files changed, 68 insertions(+) create mode 100644 arch/x86/include/asm/arch-quark/device.h create mode 100644 arch/x86/include/asm/arch-quark/quark.h
arch/x86/include/asm/arch-quark/device.h new file +28 -0
@@ -0,0 +1,28 @@ +/* +* Copyright (C) 2015, Bin Meng <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef _QUARK_DEVICE_H_ +#define _QUARK_DEVICE_H_ + +#include <pci.h> + +#define QUARK_HOST_BRIDGE PCI_BDF(0, 0, 0) +#define QUARK_MMC_SDIO PCI_BDF(0, 20, 0) +#define QUARK_UART0 PCI_BDF(0, 20, 1) +#define QUARK_USB_DEVICE PCI_BDF(0, 20, 2) +#define QUARK_USB_EHCI PCI_BDF(0, 20, 3) +#define QUARK_USB_OHCI PCI_BDF(0, 20, 4) +#define QUARK_UART1 PCI_BDF(0, 20, 5) +#define QUARK_EMAC0 PCI_BDF(0, 20, 6) +#define QUARK_EMAC1 PCI_BDF(0, 20, 7) +#define QUARK_SPI0 PCI_BDF(0, 21, 0) +#define QUARK_SPI1 PCI_BDF(0, 21, 1) +#define QUARK_I2C_GPIO PCI_BDF(0, 21, 2) +#define QUARK_PCIE0 PCI_BDF(0, 23, 0) +#define QUARK_PCIE1 PCI_BDF(0, 23, 1) +#define QUARK_LEGACY_BRIDGE PCI_BDF(0, 31, 0) + +#endif /* _QUARK_DEVICE_H_ */
arch/x86/include/asm/arch-quark/quark.h new file +40 -0
@@ -0,0 +1,40 @@ +/* +* Copyright (C) 2015, Bin Meng <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef _QUARK_H_ +#define _QUARK_H_ + +/* Message Bus Ports */ +#define MSG_PORT_MEM_ARBITER 0x00 +#define MSG_PORT_HOST_BRIDGE 0x03 +#define MSG_PORT_RMU 0x04 +#define MSG_PORT_MEM_MGR 0x05 +#define MSG_PORT_SOC_UNIT 0x31 + +/* Host Memory I/O Boundary */ +#define HM_BOUND 0x08 + +/* eSRAM Block Page Control */ +#define ESRAM_BLK_CTRL 0x82 +#define ESRAM_BLOCK_MODE 0x10000000 + +/* DRAM */ +#define DRAM_BASE 0x00000000 +#define DRAM_MAX_SIZE 0x80000000 + +/* eSRAM */ +#define ESRAM_SIZE 0x80000 + +/* Memory BAR Enable */ +#define MEM_BAR_EN 0x00000001 + +/* I/O BAR Enable */ +#define IO_BAR_EN 0x80000000 + +/* 64KiB of RMU binary in flash */ +#define RMU_BINARY_SIZE 0x10000 + +#endif /* _QUARK_H_ */
Signature · 1 line
1.8.2.1
RFC PATCH v3 1/7 x86: Add header files for Intel Quark SoC defines
Quoted 10 lines · Bin Meng
device.hfor integrated pci devices' bdf on Quark SoC andquark.hfor various memory-mapped and i/o-mapped base addresses within SoC.Signed-off-by Bin Meng <[email protected]>---
Changes in v3:
- Add several macros for message bus port and registers
Quoted 8 lines
Changes in v2:
- Move vairous components' base addresses within Quark SoC toKconfigarch/x86/include/asm/arch-quark/device.h | 28 ++++++++++++++++++++++ arch/x86/include/asm/arch-quark/quark.h | 40 ++++++++++++++++++++++++++++++++ 2 files changed, 68 insertions(+) create mode 100644 arch/x86/include/asm/arch-quark/device.h create mode 100644 arch/x86/include/asm/arch-quark/quark.h
RFC PATCH v3 1/7 x86: Add header files for Intel Quark SoC defines
Quoted 14 lines · Simon Glass
Quoted 13 lines · Bin Meng
device.hfor integrated pci devices' bdf on Quark SoC andquark.hfor various memory-mapped and i/o-mapped base addresses within SoC.Signed-off-by Bin Meng <[email protected]>---
Changes in v3:
- Add several macros for message bus port and registersChanges in v2:
- Move vairous components' base addresses within Quark SoC toKconfig
Quoted 7 lines
Quoted 5 lines
arch/x86/include/asm/arch-quark/device.h | 28 ++++++++++++++++++++++ arch/x86/include/asm/arch-quark/quark.h | 40 ++++++++++++++++++++++++++++++++ 2 files changed, 68 insertions(+) create mode 100644 arch/x86/include/asm/arch-quark/device.h create mode 100644 arch/x86/include/asm/arch-quark/quark.hAcked-by Simon Glass <[email protected]>
Applied to u-boot-x86, thanks!
RFC PATCH v3 2/7 x86: quark: Add routines to access message bus registers
In reply to Bin MengIn the Quark SoC, some chipset commands are accomplished by utilizing the internal message network within the host bridge (D0:F0). Accesses to this network are accomplished by populating the message control register (MCR), Message Control Register eXtension (MCRX) and the message data register (MDR).
---
Changes in v3:
- Use lower case hex
Changes in v2:
- Add msg_port_setup() and remove MCR_FILL
- Add MSG_BYTE_ENABLE define
- Wrap function declaraion with __ASSEMBLY__
arch/x86/cpu/quark/msg_port.c | 77 +++++++++++++++++++++ arch/x86/include/asm/arch-quark/msg_port.h | 106 +++++++++++++++++++++++++++++ 2 files changed, 183 insertions(+) create mode 100644 arch/x86/cpu/quark/msg_port.c create mode 100644 arch/x86/include/asm/arch-quark/msg_port.h
arch/x86/cpu/quark/msg_port.c new file +77 -0
@@ -0,0 +1,77 @@ +/* +* Copyright (C) 2015, Bin Meng <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#include <common.h> +#include <pci.h> +#include <asm/arch/device.h> +#include <asm/arch/msg_port.h> + +void msg_port_setup (int op,int port,int reg) +{ +pci_write_config_dword (QUARK_HOST_BRIDGE ,MSG_CTRL_REG , + (((op) <<24 ) | ((port) <<16 ) | + (((reg) <<8 ) &0xff00 ) |MSG_BYTE_ENABLE )); +} + +u32 msg_port_read (u8 port,u32 reg) +{ +u32 value; + +pci_write_config_dword (QUARK_HOST_BRIDGE ,MSG_CTRL_EXT_REG , + reg &0xffffff00 ); +msg_port_setup (MSG_OP_READ , port, reg); +pci_read_config_dword (QUARK_HOST_BRIDGE ,MSG_DATA_REG , &value); + +return value; +} + +void msg_port_write (u8 port,u32 reg,u32 value) +{ +pci_write_config_dword (QUARK_HOST_BRIDGE ,MSG_DATA_REG , value); +pci_write_config_dword (QUARK_HOST_BRIDGE ,MSG_CTRL_EXT_REG , + reg &0xffffff00 ); +msg_port_setup (MSG_OP_WRITE , port, reg); +} + +u32 msg_port_alt_read (u8 port,u32 reg) +{ +u32 value; + +pci_write_config_dword (QUARK_HOST_BRIDGE ,MSG_CTRL_EXT_REG , + reg &0xffffff00 ); +msg_port_setup (MSG_OP_ALT_READ , port, reg); +pci_read_config_dword (QUARK_HOST_BRIDGE ,MSG_DATA_REG , &value); + +return value; +} + +void msg_port_alt_write (u8 port,u32 reg,u32 value) +{ +pci_write_config_dword (QUARK_HOST_BRIDGE ,MSG_DATA_REG , value); +pci_write_config_dword (QUARK_HOST_BRIDGE ,MSG_CTRL_EXT_REG , + reg &0xffffff00 ); +msg_port_setup (MSG_OP_ALT_WRITE , port, reg); +} + +u32 msg_port_io_read (u8 port,u32 reg) +{ +u32 value; + +pci_write_config_dword (QUARK_HOST_BRIDGE ,MSG_CTRL_EXT_REG , + reg &0xffffff00 ); +msg_port_setup (MSG_OP_IO_READ , port, reg); +pci_read_config_dword (QUARK_HOST_BRIDGE ,MSG_DATA_REG , &value); + +return value; +} + +void msg_port_io_write (u8 port,u32 reg,u32 value) +{ +pci_write_config_dword (QUARK_HOST_BRIDGE ,MSG_DATA_REG , value); +pci_write_config_dword (QUARK_HOST_BRIDGE ,MSG_CTRL_EXT_REG , + reg &0xffffff00 ); +msg_port_setup (MSG_OP_IO_WRITE , port, reg); +}
arch/x86/include/asm/arch-quark/msg_port.h new file +106 -0
106 lines not on this page · raw message
Signature · 1 line
1.8.2.1
RFC PATCH v3 2/7 x86: quark: Add routines to access message bus registers
Quoted 8 lines · Bin Meng
In the Quark SoC, some chipset commands are accomplished by utilizing the internal message network within the host bridge (D0:F0). Accesses to this network are accomplished by populating the message control register (MCR), Message Control Register eXtension (MCRX) and the message data register (MDR).
Signed-off-by Bin Meng <[email protected]>Acked-by Simon Glass <[email protected]>
Applied to u-boot-x86, thanks!
RFC PATCH v3 3/7 x86: Define macros for pci configuration space access
In reply to Bin MengMove PCI_REG_ADDR and PCI_REG_DATA from arch/x86/lib/pci_type1.c to arch/x86/include/asm/pci.h, also define PCI_CFG_EN so that these macros can be used for pci configuration space access.
---
Changes in v3:
- New patch to define macros for pci configuration space access
Changes in v2: None
arch/x86/include/asm/pci.h | 13 +++++++++++-- arch/x86/lib/pci_type1.c | 7 ++----- 2 files changed, 13 insertions(+), 7 deletions(-)
arch/x86/include/asm/pci.h +11 -2
@@ -1,4 +1,3 @@ -/* * (C) Copyright 2002 * Daniel Engstr?m, Omicron Ceti AB, daniel at omicron.se
@@ -9,6 +8,14 @@#ifndef _PCI_I386_H_#define _PCI_I386_H_ +/* bus mapping constants (used for PCI core initialization) */ +#define PCI_REG_ADDR 0xcf8 +#define PCI_REG_DATA 0xcfc + +#define PCI_CFG_EN 0x80000000 + +#ifndef __ASSEMBLY__ +#define DEFINE_PCI_DEVICE_TABLE (_table) \ const struct pci_device_id _table[]
@@ -49,4 +56,6 @@ void pci_write_config8(pci_dev_t dev, unsigned where, unsigned value);void pci_write_config16 (pci_dev_t dev,unsigned where,unsigned value);void pci_write_config32 (pci_dev_t dev,unsigned where,unsigned value); -#endif +#endif /* __ASSEMBLY__ */ + +#endif /* _PCI_I386_H_ */
arch/x86/lib/pci_type1.c +2 -5
@@ -12,6 +12,7 @@#include <common.h> #include <asm/io.h> #include <pci.h> +#include <asm/pci.h> #define cfg_read (val, addr, op) (*val = op((int)(addr)))#define cfg_write (val, addr, op) op((val), (int)(addr))
@@ -21,7 +22,7 @@ static int \ type1_##rw##_config_##size(struct pci_controller *hose, \ pci_dev_t dev, int offset, type val) \ { \ - outl(dev | (offset & 0xfc) | 0x80000000, (int)hose->cfg_addr); \ + outl(dev | (offset & 0xfc) | PCI_CFG_EN, (int)hose->cfg_addr); \ cfg_##rw(val, hose->cfg_data + (offset & mask), op); \ return 0; \ }
@@ -34,10 +35,6 @@ TYPE1_PCI_OP(write, byte, u8, outb, 3) TYPE1_PCI_OP(write, word, u16, outw, 2) TYPE1_PCI_OP(write, dword, u32, outl, 0) -/* bus mapping constants (used for PCI core initialization) */ -#define PCI_REG_ADDR 0x00000cf8 -#define PCI_REG_DATA 0x00000cfc -void pci_setup_type1 (struct pci_controller *hose) { pci_set_ops(hose,
Signature · 1 line
1.8.2.1
RFC PATCH v3 3/7 x86: Define macros for pci configuration space access
Quoted 8 lines · Bin Meng
Move
PCI_REG_ADDRandPCI_REG_DATAfromarch/x86/lib/pci_type1.ctoarch/x86/include/asm/pci.h, also definePCI_CFG_ENso that these macros can be used for pci configuration space access.Signed-off-by Bin Meng <[email protected]>---
Quoted 8 lines
Changes in v3:
- New patch to define macros for pci configuration space accessChanges in v2: None
arch/x86/include/asm/pci.h | 13 +++++++++++-- arch/x86/lib/pci_type1.c | 7 ++----- 2 files changed, 13 insertions(+), 7 deletions(-)
RFC PATCH v3 3/7 x86: Define macros for pci configuration space access
Quoted 12 lines · Simon Glass
Quoted 11 lines · Bin Meng
Move
PCI_REG_ADDRandPCI_REG_DATAfromarch/x86/lib/pci_type1.ctoarch/x86/include/asm/pci.h, also definePCI_CFG_ENso that these macros can be used for pci configuration space access.Signed-off-by Bin Meng <[email protected]>---
Changes in v3:
- New patch to define macros for pci configuration space access
Quoted 7 lines
Quoted 5 lines
Changes in v2: None
arch/x86/include/asm/pci.h | 13 +++++++++++-- arch/x86/lib/pci_type1.c | 7 ++----- 2 files changed, 13 insertions(+), 7 deletions(-)Acked-by Simon Glass <[email protected]>
Applied to u-boot-x86, thanks!
RFC PATCH v3 4/7 x86: quark: Add Cache-As-RAM initialization
In reply to Bin MengQuark SoC contains an embedded 512KiB SRAM (eSRAM) that is initialized by hardware. eSRAM is the ideal place to be used for Cache-As-RAM (CAR) before system memory is available.
---
Changes in v3:
- Use macros from <asm/pci.h> and <asm/arch/quark.h>
Changes in v2:
- Replace upper case register names (EAX etc.) with lower case
- Use some macros from <asm/arch/msg_port.h> and <asm/arch/quark.h>
arch/x86/cpu/quark/car.S | 105 +++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 105 insertions(+) create mode 100644 arch/x86/cpu/quark/car.S
arch/x86/cpu/quark/car.S new file +105 -0
@@ -0,0 +1,105 @@ +/* + * Copyright (C) 2015, Bin Meng <[email protected]> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <config.h> +#include <asm/pci.h> +#include <asm/post.h> +#include <asm/arch/quark.h> +#include <asm/arch/msg_port.h> + +.globl car_init +car_init: + post_code(POST_CAR_START) + + /* + * Quark SoC contains an embedded 512KiB SRAM (eSRAM) that is + * initialized by hardware. eSRAM is the ideal place to be used + * for Cache-As-RAM (CAR) before system memory is available. + * + * Relocate this eSRAM to a suitable location in the physical + * memory map and enable it. + */ + + /* Host Memory Bound Register P03h:R08h */ + mov $((MSG_PORT_HOST_BRIDGE << 16) | (HM_BOUND << 8)), %eax + mov $(DRAM_BASE + DRAM_MAX_SIZE + ESRAM_SIZE), %edx + lea 1f, %esp + jmp msg_port_write +1: + + /* eSRAM Block Page Control Register P05h:R82h */ + mov $((MSG_PORT_MEM_MGR << 16) | (ESRAM_BLK_CTRL << 8)), %eax + mov $(ESRAM_BLOCK_MODE | (CONFIG_ESRAM_BASE >> 24)), %edx + lea 2f, %esp + jmp msg_port_write +2: + + post_code(POST_CAR_CPU_CACHE) + jmp car_init_ret + +msg_port_read: + /* + * Parameter: + * eax[23:16] - Message Port ID + * eax[15:08] - Register Address + * + * Return Value: + * eax - Message Port Register value + * + * Return Address: esp + */ + + or $((MSG_OP_READ << 24) | MSG_BYTE_ENABLE), %eax + mov %eax, %ebx + + /* Write MCR B0:D0:F0:RD0 */ + mov $(PCI_CFG_EN | MSG_CTRL_REG), %eax + mov $PCI_REG_ADDR, %dx + out %eax, %dx + mov $PCI_REG_DATA, %dx + mov %ebx, %eax + out %eax, %dx + + /* Read MDR B0:D0:F0:RD4 */ + mov $(PCI_CFG_EN | MSG_DATA_REG), %eax + mov $PCI_REG_ADDR, %dx + out %eax, %dx + mov $PCI_REG_DATA, %dx + in %dx, %eax + + jmp *%esp + +msg_port_write: + /* + * Parameter: + * eax[23:16] - Message Port ID + * eax[15:08] - Register Address + * edx - Message Port Register value to write + * + * Return Address: esp + */ + + or $((MSG_OP_WRITE << 24) | MSG_BYTE_ENABLE), %eax + mov %eax, %esi + mov %edx, %edi + + /* Write MDR B0:D0:F0:RD4 */ + mov $(PCI_CFG_EN | MSG_DATA_REG), %eax + mov $PCI_REG_ADDR, %dx + out %eax, %dx + mov $PCI_REG_DATA, %dx + mov %edi, %eax + out %eax, %dx + + /* Write MCR B0:D0:F0:RD0 */ + mov $(PCI_CFG_EN | MSG_CTRL_REG), %eax + mov $PCI_REG_ADDR, %dx + out %eax, %dx + mov $PCI_REG_DATA, %dx + mov %esi, %eax + out %eax, %dx + + jmp *%esp
Signature · 1 line
1.8.2.1
RFC PATCH v3 4/7 x86: quark: Add Cache-As-RAM initialization
Quoted 11 lines · Bin Meng
Quark SoC contains an embedded 512KiB SRAM (eSRAM) that is initialized by hardware. eSRAM is the ideal place to be used for Cache-As-RAM (CAR) before system memory is available.
Signed-off-by Bin Meng <[email protected]>---
Changes in v3:
- Use macros from <asm/pci.h> and <asm/arch/quark.h>
Quoted 7 lines
Changes in v2:
- Replace upper case register names (EAX etc.) with lower case
- Use some macros from <asm/arch/msg_port.h> and <asm/arch/quark.h>arch/x86/cpu/quark/car.S | 105 +++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 105 insertions(+) create mode 100644 arch/x86/cpu/quark/car.S
RFC PATCH v3 4/7 x86: quark: Add Cache-As-RAM initialization
Quoted 16 lines · Simon Glass
Quoted 15 lines · Bin Meng
Quark SoC contains an embedded 512KiB SRAM (eSRAM) that is initialized by hardware. eSRAM is the ideal place to be used for Cache-As-RAM (CAR) before system memory is available.
Signed-off-by Bin Meng <[email protected]>---
Changes in v3:
- Use macros from <asm/pci.h> and <asm/arch/quark.h>Changes in v2:
- Replace upper case register names (EAX etc.) with lower case
- Use some macros from <asm/arch/msg_port.h> and <asm/arch/quark.h>
Quoted 5 lines
Quoted 3 lines
arch/x86/cpu/quark/car.S | 105 +++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 105 insertions(+) create mode 100644 arch/x86/cpu/quark/car.SAcked-by Simon Glass <[email protected]>
Applied to u-boot-x86, thanks!
RFC PATCH v3 5/7 x86: Add basic Intel Quark processor support
In reply to Bin MengAdd minimum codes to support Intel Quark SoC. DRAM initialization is not ready yet so a hardcoded gd->ram_size is assigned.
---
Changes in v3:
- Add simple help for ACPI PM1, PBLK and GEP0
Changes in v2:
- Use machine-specific
- Move vairous components' base addresses within Quark SoC to Kconfig
- Rebase to u-boot-86/master
arch/x86/cpu/quark/Kconfig | 121 +++++++++++++++++++++++++++++++++ arch/x86/cpu/quark/Makefile | 8 +++ arch/x86/cpu/quark/dram.c | 39 +++++++++++ arch/x86/cpu/quark/pci.c | 70 +++++++++++++++++++ arch/x86/cpu/quark/quark.c | 44 ++++++++++++ arch/x86/include/asm/arch-quark/gpio.h | 13 ++++ 6 files changed, 295 insertions(+) create mode 100644 arch/x86/cpu/quark/Kconfig create mode 100644 arch/x86/cpu/quark/Makefile create mode 100644 arch/x86/cpu/quark/dram.c create mode 100644 arch/x86/cpu/quark/pci.c create mode 100644 arch/x86/cpu/quark/quark.c create mode 100644 arch/x86/include/asm/arch-quark/gpio.h
arch/x86/cpu/quark/Kconfig new file +121 -0
@@ -0,0 +1,121 @@ +# +# Copyright (C) 2015, Bin Meng <[email protected]> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +config INTEL_QUARK + bool + select HAVE_RMU + +if INTEL_QUARK + +config HAVE_RMU + bool "Add a Remote Management Unit (RMU) binary" + help + Select this option to add a Remote Management Unit (RMU) binary + to the resulting U-Boot image. It is a data block (up to 64K) of + machine-specific code which must be put in the flash for the RMU + within the Quark SoC processor to access when powered up before + system BIOS is executed. + +config RMU_FILE + string "Remote Management Unit (RMU) binary filename" + depends on HAVE_RMU + default "rmu.bin" + help + The filename of the file to use as Remote Management Unit (RMU) + binary in the board directory. + +config RMU_ADDR + hex "Remote Management Unit (RMU) binary location" + depends on HAVE_RMU + default 0xfff00000 + help + The location of the RMU binary is determined by a strap. It must be + put in flash at a location matching the strap-determined base address. + + The default base address of 0xfff00000 indicates that the binary must + be located at offset 0 from the beginning of a 1MB flash device. + +config HAVE_CMC + bool + default HAVE_RMU + +config CMC_FILE + string + depends on HAVE_CMC + default RMU_FILE + +config CMC_ADDR + hex + depends on HAVE_CMC + default RMU_ADDR + +config ESRAM_BASE + hex + default 0x80000000 + help + Embedded SRAM (eSRAM) memory-mapped base address. + +config PCIE_ECAM_BASE + hex + default 0xe0000000 + +config RCBA_BASE + hex + default 0xfed1c000 + help + Root Complex register block memory-mapped base address. + +config ACPI_PM1_BASE + hex + default 0x1000 + help + ACPI Power Managment 1 (PM1) i/o-mapped base address. + This device is defined in ACPI specification, with 16 bytes in size. + +config ACPI_PBLK_BASE + hex + default 0x1010 + help + ACPI Processor Block (PBLK) i/o-mapped base address. + This device is defined in ACPI specification, with 16 bytes in size. + +config SPI_DMA_BASE + hex + default 0x1020 + help + SPI DMA i/o-mapped base address. + +config GPIO_BASE + hex + default 0x1080 + help + GPIO i/o-mapped base address. + +config ACPI_GPE0_BASE + hex + default 0x1100 + help + ACPI General Purpose Event 0 (GPE0) i/o-mapped base address. + This device is defined in ACPI specification, with 64 bytes in size. + +config WDT_BASE + hex + default 0x1140 + help + Watchdog timer i/o-mapped base address. + +config SYS_CAR_ADDR + hex + default ESRAM_BASE + +config SYS_CAR_SIZE + hex + default 0x8000 + help + Space in bytes in eSRAM used as Cache-As-ARM (CAR). + Note this size must not exceed eSRAM's total size. + +endif
arch/x86/cpu/quark/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +# +# Copyright (C) 2015, Bin Meng <[email protected]> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += car.o dram.o msg_port.o quark.o +obj-$(CONFIG_PCI) += pci.o
arch/x86/cpu/quark/dram.c new file +39 -0
@@ -0,0 +1,39 @@ +/* +* Copyright (C) 2015, Bin Meng <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#include <common.h> +#include <asm/post.h> +#include <asm/arch/quark.h> + +DECLARE_GLOBAL_DATA_PTR ; + +int dram_init (void ) +{ +/* hardcode the DRAM size for now */ + gd->ram_size =DRAM_MAX_SIZE ; +post_code (POST_DRAM ); + +return 0 ; +} + +void dram_init_banksize (void ) +{ + gd->bd->bi_dram[0 ].start =0 ; + gd->bd->bi_dram[0 ].size = gd->ram_size; +} + +/* +* This function looks for the highest region of memory lower than 4GB which +* has enough space for U-Boot where U-Boot is aligned on a page boundary. +* It overrides the default implementation found elsewhere which simply +* picks the end of ram, wherever that may be. The location of the stack, +* the relocation address, and how far U-Boot is moved by relocation are +* set in the global data structure. +*/ +ulong board_get_usable_ram_top (ulong total_size) +{ +return gd->ram_size; +}
arch/x86/cpu/quark/pci.c new file +70 -0
70 lines not on this page · raw message
arch/x86/cpu/quark/quark.c new file +44 -0
44 lines not on this page · raw message
arch/x86/include/asm/arch-quark/gpio.h new file +13 -0
@@ -0,0 +1,13 @@ +/* +* Copyright (C) 2015, Bin Meng <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef _X86_ARCH_GPIO_H_ +#define _X86_ARCH_GPIO_H_ + +/* Where in config space is the register that points to the GPIO registers? */ +#define PCI_CFG_GPIOBASE 0x44 + +#endif /* _X86_ARCH_GPIO_H_ */
Signature · 1 line
1.8.2.1
RFC PATCH v3 5/7 x86: Add basic Intel Quark processor support
Quoted 15 lines · Bin Meng
Add minimum codes to support Intel Quark SoC. DRAM initialization is not ready yet so a hardcoded
gd->ram_sizeis assigned.Signed-off-by Bin Meng <[email protected]>---
Changes in v3:
- Add simple help for ACPI PM1, PBLK and GEP0Changes in v2:
- Use machine-specific
- Move vairous components' base addresses within Quark SoC toKconfig
- Rebase to u-boot-86/master
Quoted 13 lines
arch/x86/cpu/quark/Kconfig | 121 +++++++++++++++++++++++++++++++++ arch/x86/cpu/quark/Makefile | 8 +++ arch/x86/cpu/quark/dram.c | 39 +++++++++++ arch/x86/cpu/quark/pci.c | 70 +++++++++++++++++++ arch/x86/cpu/quark/quark.c | 44 ++++++++++++ arch/x86/include/asm/arch-quark/gpio.h | 13 ++++ 6 files changed, 295 insertions(+) create mode 100644 arch/x86/cpu/quark/Kconfig create mode 100644 arch/x86/cpu/quark/Makefile create mode 100644 arch/x86/cpu/quark/dram.c create mode 100644 arch/x86/cpu/quark/pci.c create mode 100644 arch/x86/cpu/quark/quark.c create mode 100644 arch/x86/include/asm/arch-quark/gpio.h
RFC PATCH v3 5/7 x86: Add basic Intel Quark processor support
Quoted 30 lines · Simon Glass
Quoted 15 lines · Bin Meng
Add minimum codes to support Intel Quark SoC. DRAM initialization is not ready yet so a hardcoded
gd->ram_sizeis assigned.Signed-off-by Bin Meng <[email protected]>---
Changes in v3:
- Add simple help for ACPI PM1, PBLK and GEP0Changes in v2:
- Use machine-specific
- Move vairous components' base addresses within Quark SoC toKconfig
- Rebase to u-boot-86/masterQuoted 13 lines
arch/x86/cpu/quark/Kconfig | 121 +++++++++++++++++++++++++++++++++ arch/x86/cpu/quark/Makefile | 8 +++ arch/x86/cpu/quark/dram.c | 39 +++++++++++ arch/x86/cpu/quark/pci.c | 70 +++++++++++++++++++ arch/x86/cpu/quark/quark.c | 44 ++++++++++++ arch/x86/include/asm/arch-quark/gpio.h | 13 ++++ 6 files changed, 295 insertions(+) create mode 100644 arch/x86/cpu/quark/Kconfig create mode 100644 arch/x86/cpu/quark/Makefile create mode 100644 arch/x86/cpu/quark/dram.c create mode 100644 arch/x86/cpu/quark/pci.c create mode 100644 arch/x86/cpu/quark/quark.c create mode 100644 arch/x86/include/asm/arch-quark/gpio.h
Quoted 1 line
Acked-by Simon Glass <[email protected]>
Applied to u-boot-x86, thanks!
RFC PATCH v3 6/7 x86: Add basic Intel Galileo board support
In reply to Bin MengNew board/intel/galileo board directory with minimum codes, plus board dts, defconfig and configuration files.
---
Changes in v3: None
Changes in v2: None
arch/x86/dts/Makefile | 1 + arch/x86/dts/galileo.dts | 43 +++++++++++++++++++++++++++++++++ board/intel/galileo/Kconfig | 21 ++++++++++++++++ board/intel/galileo/MAINTAINERS | 6 +++++ board/intel/galileo/Makefile | 7 ++++++ board/intel/galileo/galileo.c | 19 +++++++++++++++ board/intel/galileo/start.S | 9 +++++++ configs/galileo_defconfig | 6 +++++ include/configs/galileo.h | 53 +++++++++++++++++++++++++++++++++++++++++ 9 files changed, 165 insertions(+) create mode 100644 arch/x86/dts/galileo.dts create mode 100644 board/intel/galileo/Kconfig create mode 100644 board/intel/galileo/MAINTAINERS create mode 100644 board/intel/galileo/Makefile create mode 100644 board/intel/galileo/galileo.c create mode 100644 board/intel/galileo/start.S create mode 100644 configs/galileo_defconfig create mode 100644 include/configs/galileo.h
arch/x86/dts/Makefile +1 -0
@@ -1,5 +1,6 @@ dtb-y += chromebook_link.dtb \ crownbay.dtb \ + galileo.dtb \ minnowmax.dtb targets += $(dtb-y)
arch/x86/dts/galileo.dts new file +43 -0
43 lines not on this page · raw message
board/intel/galileo/Kconfig new file +21 -0
@@ -0,0 +1,21 @@ +if TARGET_GALILEO + +config SYS_BOARD + default "galileo" + +config SYS_VENDOR + default "intel" + +config SYS_SOC + default "quark" + +config SYS_CONFIG_NAME + default "galileo" + +config BOARD_SPECIFIC_OPTIONS # dummy + def_bool y + select X86_RESET_VECTOR + select INTEL_QUARK + select BOARD_ROMSIZE_KB_1024 + +endif
board/intel/galileo/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +INTEL GALILEO BOARD +M: Bin Meng <[email protected]> +S: Maintained +F: board/intel/galileo/ +F: include/configs/galileo.h +F: configs/galileo_defconfig
board/intel/galileo/Makefile new file +7 -0
@@ -0,0 +1,7 @@ +# +# Copyright (C) 2015, Bin Meng <[email protected]> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += galileo.o start.o
board/intel/galileo/galileo.c new file +19 -0
@@ -0,0 +1,19 @@ +/* +* Copyright (C) 2015, Bin Meng <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#include <common.h> + +DECLARE_GLOBAL_DATA_PTR ; + +int board_early_init_f (void ) +{ +return 0 ; +} + +void setup_pch_gpios (u16 gpiobase,const struct pch_gpio_map *gpio) +{ +return ; +}
board/intel/galileo/start.S new file +9 -0
@@ -0,0 +1,9 @@ +/* + * Copyright (C) 2015, Bin Meng <[email protected]> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +.globl early_board_init +early_board_init: + jmp early_board_init_ret
configs/galileo_defconfig new file +6 -0
@@ -0,0 +1,6 @@ +CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xfff10000" +CONFIG_X86=y +CONFIG_TARGET_GALILEO=y +CONFIG_OF_CONTROL=y +CONFIG_OF_SEPARATE=y +CONFIG_DEFAULT_DEVICE_TREE="galileo"
include/configs/galileo.h new file +53 -0
53 lines not on this page · raw message
Signature · 1 line
1.8.2.1
RFC PATCH v3 6/7 x86: Add basic Intel Galileo board support
Quoted 6 lines · Bin Meng
New board/intel/galileo board directory with minimum codes, plus board dts, defconfig and configuration files.
Signed-off-by Bin Meng <[email protected]>Reviewed-by Simon Glass <[email protected]>Acked-by Simon Glass <[email protected]>
Applied to u-boot-x86, thanks!
RFC PATCH v3 7/7 x86: Enable the Intel quark/galileo build
In reply to Bin MengMake the Intel quark/galileo support avaiable in Kconfig and Makefile. With this patch, we can generate u-boot.rom for Intel galileo board.
---
Changes in v3: None
Changes in v2:
- Use Arduino-certified
arch/x86/Kconfig | 17 +++++++++++++++++ arch/x86/cpu/Makefile | 1 + 2 files changed, 18 insertions(+)
arch/x86/Kconfig +17 -0
@@ -52,6 +52,19 @@ config TARGET_MINNOWMAX Note that PCIE_ECAM_BASE is set up by the FSP so the value used by U-Boot matches that value. +config TARGET_GALILEO + bool "Support Intel Galileo" + help + This is the Intel Galileo board, which is the first in a family of + Arduino-certified development and prototyping boards based on Intel + architecture. It includes an Intel Quark SoC X1000 processor, a 32-bit + single-core, single-thread, Intel Pentium processor instrunction set + architecture (ISA) compatible, operating at speeds up to 400Mhz, + along with 256MB DDR3 memory. It supports a wide range of industry + standard I/O interfaces, including a full-sized mini-PCIe slot, + one 100Mb Ethernet port, a microSD card slot, a USB host port and + a USB client port. + endchoice config RAMBASE
@@ -399,6 +412,8 @@ source "arch/x86/cpu/coreboot/Kconfig" source "arch/x86/cpu/ivybridge/Kconfig" +source "arch/x86/cpu/quark/Kconfig" + source "arch/x86/cpu/queensbay/Kconfig" source "board/coreboot/coreboot/Kconfig"
@@ -409,6 +424,8 @@ source "board/intel/crownbay/Kconfig" source "board/intel/minnowmax/Kconfig" +source "board/intel/galileo/Kconfig" + config PCIE_ECAM_BASE hex default 0xe0000000
arch/x86/cpu/Makefile +1 -0
@@ -16,6 +16,7 @@ obj-$(CONFIG_INTEL_BAYTRAIL) += baytrail/ obj-$(CONFIG_SYS_COREBOOT) += coreboot/ obj-$(CONFIG_NORTHBRIDGE_INTEL_SANDYBRIDGE) += ivybridge/ obj-$(CONFIG_NORTHBRIDGE_INTEL_IVYBRIDGE) += ivybridge/ +obj-$(CONFIG_INTEL_QUARK) += quark/ obj-$(CONFIG_INTEL_QUEENSBAY) += queensbay/ obj-y += lapic.o obj-y += mtrr.o
Signature · 1 line
1.8.2.1
RFC PATCH v3 7/7 x86: Enable the Intel quark/galileo build
Quoted 6 lines · Bin Meng
Make the Intel quark/galileo support avaiable in
KconfigandMakefile. With this patch, we can generate u-boot.rom for Intel galileo board.Signed-off-by Bin Meng <[email protected]>Reviewed-by Simon Glass <[email protected]>Acked-by Simon Glass <[email protected]>
Applied to u-boot-x86, thanks!