Skip to contentSkip to conversation

dgnc: clean up digi.h

PATCH In review Giedrius Statkevičius 2 participants 8 messages Mar 12, 2015 Staging

lore
Share & tools
lore
#0 lore raw

PATCH 1/6 dgnc: clean up digi.h

Remove a lot of unused #defines and struct definitions from digi.h. In dgnc_mgmt.c, termios.h is included before that defines it's own TIOCM_LE and others protected under #ifndef in digi.h so we can't delete them yet. Also, be careful with TIOCMSET and TIOCMBIC since include/uapi/asm-generic/ioctls.h defines them too.

---
 drivers/staging/dgnc/digi.h | 235 --------------------------------------------
 1 file changed, 235 deletions(-)
drivers/staging/dgnc/digi.h +0 -235
index 554fbeb..7e5e6b0 100644
@@ -16,25 +16,6 @@
 #ifndef __DIGI_H
 #define __DIGI_H
 
-/************************************************************************
- ***	Definitions for Digi ditty(1) command.
- ************************************************************************/
-
-
-/*
- * Copyright (c) 1988-96 Digi International Inc., All Rights Reserved.
- */
-
-/************************************************************************
- * This module provides application access to special Digi
- * serial line enhancements which are not standard UNIX(tm) features.
- ************************************************************************/
-
-#if !defined(TIOCMODG)
-
-#define	TIOCMODG	(('d'<<8) | 250)	/* get modem ctrl state	*/
-#define	TIOCMODS	(('d'<<8) | 251)	/* set modem ctrl state	*/
-
 #ifndef TIOCM_LE
 #define		TIOCM_LE	0x01		/* line enable		*/
 #define		TIOCM_DTR	0x02		/* data terminal ready	*/
@@ -49,8 +30,6 @@
 #define		TIOCM_CD	TIOCM_CAR	/* carrier detect (alt)	*/
 #endif
 
-#endif
-
 #if !defined(TIOCMSET)
 #define	TIOCMSET	(('d'<<8) | 252)	/* set modem ctrl state	*/
 #define	TIOCMGET	(('d'<<8) | 253)	/* set modem ctrl state	*/
@@ -61,83 +40,19 @@
 #define	TIOCMBIS	(('d'<<8) | 255)	/* set modem ctrl state */
 #endif
 
-
-#if !defined(TIOCSDTR)
-#define	TIOCSDTR	(('e'<<8) | 0)		/* set DTR		*/
-#define	TIOCCDTR	(('e'<<8) | 1)		/* clear DTR		*/
-#endif
-
-/************************************************************************
- * Ioctl command arguments for DIGI parameters.
- ************************************************************************/
 #define DIGI_GETA	(('e'<<8) | 94)		/* Read params		*/
-
 #define DIGI_SETA	(('e'<<8) | 95)		/* Set params		*/
 #define DIGI_SETAW	(('e'<<8) | 96)		/* Drain & set params	*/
 #define DIGI_SETAF	(('e'<<8) | 97)		/* Drain, flush & set params */
-
-#define DIGI_KME	(('e'<<8) | 98)		/* Read/Write Host	*/
-						/* Adapter Memory	*/
-
-#define	DIGI_GETFLOW	(('e'<<8) | 99)		/* Get startc/stopc flow */
-						/* control characters	 */
-#define	DIGI_SETFLOW	(('e'<<8) | 100)	/* Set startc/stopc flow */
-						/* control characters	 */
-#define	DIGI_GETAFLOW	(('e'<<8) | 101)	/* Get Aux. startc/stopc */
-						/* flow control chars	 */
-#define	DIGI_SETAFLOW	(('e'<<8) | 102)	/* Set Aux. startc/stopc */
-						/* flow control chars	 */
-
-#define DIGI_GEDELAY	(('d'<<8) | 246)	/* Get edelay */
-#define DIGI_SEDELAY	(('d'<<8) | 247)	/* Set edelay */
-
-struct	digiflow_t {
-	unsigned char	startc;				/* flow cntl start char	*/
-	unsigned char	stopc;				/* flow cntl stop char	*/
-};
-
-
-#ifdef	FLOW_2200
-#define	F2200_GETA	(('e'<<8) | 104)	/* Get 2x36 flow cntl flags */
-#define	F2200_SETAW	(('e'<<8) | 105)	/* Set 2x36 flow cntl flags */
-#define		F2200_MASK	0x03		/* 2200 flow cntl bit mask  */
-#define		FCNTL_2200	0x01		/* 2x36 terminal flow cntl  */
-#define		PCNTL_2200	0x02		/* 2x36 printer flow cntl   */
-#define	F2200_XON	0xf8
-#define	P2200_XON	0xf9
-#define	F2200_XOFF	0xfa
-#define	P2200_XOFF	0xfb
-
-#define	FXOFF_MASK	0x03			/* 2200 flow status mask    */
-#define	RCVD_FXOFF	0x01			/* 2x36 Terminal XOFF rcvd  */
-#define	RCVD_PXOFF	0x02			/* 2x36 Printer XOFF rcvd   */
-#endif
-
-/************************************************************************
- * Values for digi_flags
- ************************************************************************/
-#define DIGI_IXON	0x0001		/* Handle IXON in the FEP	*/
 #define DIGI_FAST	0x0002		/* Fast baud rates		*/
 #define RTSPACE		0x0004		/* RTS input flow control	*/
 #define CTSPACE		0x0008		/* CTS output flow control	*/
-#define DSRPACE		0x0010		/* DSR output flow control	*/
-#define DCDPACE		0x0020		/* DCD output flow control	*/
-#define DTRPACE		0x0040		/* DTR input flow control	*/
 #define DIGI_COOK	0x0080		/* Cooked processing done in FEP */
 #define DIGI_FORCEDCD	0x0100		/* Force carrier		*/
 #define	DIGI_ALTPIN	0x0200		/* Alternate RJ-45 pin config	*/
-#define	DIGI_AIXON	0x0400		/* Aux flow control in fep	*/
 #define	DIGI_PRINTER	0x0800		/* Hold port open for flow cntrl*/
-#define DIGI_PP_INPUT	0x1000		/* Change parallel port to input*/
 #define DIGI_DTR_TOGGLE	0x2000		/* Support DTR Toggle           */
-#define DIGI_422	0x4000		/* for 422/232 selectable panel */
 #define DIGI_RTS_TOGGLE	0x8000		/* Support RTS Toggle		*/
-
-/************************************************************************
- * These options are not supported on the comxi.
- ************************************************************************/
-#define	DIGI_COMXI	(DIGI_FAST|DIGI_COOK|DSRPACE|DCDPACE|DTRPACE)
-
 #define DIGI_PLEN	28		/* String length		*/
 #define	DIGI_TSIZ	10		/* Terminal string len		*/
 
@@ -157,76 +72,6 @@ struct digi_t {
 };
 
 /************************************************************************
- * KME definitions and structures.
- ************************************************************************/
-#define	RW_IDLE		0	/* Operation complete			*/
-#define	RW_READ		1	/* Read Concentrator Memory		*/
-#define	RW_WRITE	2	/* Write Concentrator Memory		*/
-
-struct rw_t {
-	unsigned char	rw_req;		/* Request type			*/
-	unsigned char	rw_board;	/* Host Adapter board number	*/
-	unsigned char	rw_conc;	/* Concentrator number		*/
-	unsigned char	rw_reserved;	/* Reserved for expansion	*/
-	unsigned int	rw_addr;	/* Address in concentrator	*/
-	unsigned short	rw_size;	/* Read/write request length	*/
-	unsigned char	rw_data[128];	/* Data to read/write		*/
-};
-
-/***********************************************************************
- * Shrink Buffer and Board Information definitions and structures.
-
- ************************************************************************/
-			/* Board type return codes */
-#define	PCXI_TYPE 1     /* Board type at the designated port is a PC/Xi */
-#define PCXM_TYPE 2     /* Board type at the designated port is a PC/Xm */
-#define	PCXE_TYPE 3     /* Board type at the designated port is a PC/Xe */
-#define	MCXI_TYPE 4     /* Board type at the designated port is a MC/Xi */
-#define COMXI_TYPE 5     /* Board type at the designated port is a COM/Xi */
-
-			 /* Non-Zero Result codes. */
-#define RESULT_NOBDFND 1 /* A Digi product at that port is not config installed */
-#define RESULT_NODESCT 2 /* A memory descriptor was not obtainable */
-#define RESULT_NOOSSIG 3 /* FEP/OS signature was not detected on the board */
-#define RESULT_TOOSML  4 /* Too small an area to shrink.  */
-#define RESULT_NOCHAN  5 /* Channel structure for the board was not found */
-
-struct shrink_buf_struct {
-	unsigned int	shrink_buf_vaddr;	/* Virtual address of board */
-	unsigned int	shrink_buf_phys;	/* Physical address of board */
-	unsigned int	shrink_buf_bseg;	/* Amount of board memory */
-	unsigned int	shrink_buf_hseg;	/* '186 Beginning of Dual-Port */
-
-	unsigned int	shrink_buf_lseg;	/* '186 Beginning of freed memory */
-	unsigned int	shrink_buf_mseg;	/* Linear address from start of
-						   dual-port were freed memory
-						   begins, host viewpoint. */
-
-	unsigned int	shrink_buf_bdparam;	/* Parameter for xxmemon and
-						   xxmemoff */
-
-	unsigned int	shrink_buf_reserva;	/* Reserved */
-	unsigned int	shrink_buf_reservb;	/* Reserved */
-	unsigned int	shrink_buf_reservc;	/* Reserved */
-	unsigned int	shrink_buf_reservd;	/* Reserved */
-
-	unsigned char	shrink_buf_result;	/* Reason for call failing
-						   Zero is Good return */
-	unsigned char	shrink_buf_init;	/* Non-Zero if it caused an
-						   xxinit call. */
-
-	unsigned char	shrink_buf_anports;	/* Number of async ports  */
-	unsigned char	shrink_buf_snports;	/* Number of sync  ports */
-	unsigned char	shrink_buf_type;	/* Board type 1 = PC/Xi,
-							      2 = PC/Xm,
-							      3 = PC/Xe
-							      4 = MC/Xi
-							      5 = COMX/i */
-	unsigned char	shrink_buf_card;	/* Card number */
-
-};
-
-/************************************************************************
  * Structure to get driver status information
  ************************************************************************/
 struct digi_dinfo {
@@ -270,7 +115,6 @@ struct digi_stat {
 	unsigned int	info_reserved[8];	/* for future expansion    */
 };
 
-#define	DIGI_GETSTAT	(('d'<<8) | 244)	/* get board info          */
 /************************************************************************
  *
  * Structure used with ioctl commands for per-channel information
@@ -290,19 +134,6 @@ struct digi_ch {
 	int		reserved[8];		/* reserved for future use */
 };
 
-/*
-* This structure is used with the DIGI_FEPCMD ioctl to
-* tell the driver which port to send the command for.
-*/
-struct digi_cmd {
-	int	cmd;
-	int	word;
-	int	ncmds;
-	int	chan; /* channel index (zero based) */
-	int	bdid; /* board index (zero based) */
-};
-
-
 struct digi_getbuffer /* Struct for holding buffer use counts */
 {
 	unsigned long tIn;
@@ -322,63 +153,9 @@ struct digi_getcounter {
 	unsigned long tbytes;		/* number of bytes transmitted fully */
 };
 
-/*
-*  info_sleep_stat defines
-*/
-#define INFO_RUNWAIT	0x0001
-#define INFO_WOPEN	0x0002
-#define INFO_TTIOW	0x0004
-#define INFO_CH_RWAIT	0x0008
-#define INFO_CH_WEMPTY	0x0010
-#define INFO_CH_WLOW	0x0020
-#define INFO_XXBUF_BUSY 0x0040
-
-#define	DIGI_GETCH	(('d'<<8) | 245)	/* get board info          */
-
-/* Board type definitions */
-
-#define	SUBTYPE		0007
-#define	T_PCXI		0000
-#define T_PCXM		0001
-#define T_PCXE		0002
-#define T_PCXR		0003
-#define T_SP		0004
-#define T_SP_PLUS	0005
-#	define T_HERC	0000
-#	define T_HOU	0001
-#	define T_LON	0002
-#	define T_CHA	0003
-#define FAMILY		0070
-#define T_COMXI		0000
-#define T_PCXX		0010
-#define T_CX		0020
-#define T_EPC		0030
-#define	T_PCLITE	0040
-#define	T_SPXX		0050
-#define	T_AVXX		0060
-#define T_DXB		0070
-#define T_A2K_4_8	0070
-#define BUSTYPE		0700
-#define T_ISABUS	0000
-#define T_MCBUS		0100
-#define	T_EISABUS	0200
-#define	T_PCIBUS	0400
-
 /* Board State Definitions */
-
 #define	BD_RUNNING	0x0
-#define	BD_REASON	0x7f
-#define	BD_NOTFOUND	0x1
-#define	BD_NOIOPORT	0x2
-#define	BD_NOMEM	0x3
-#define	BD_NOBIOS	0x4
 #define	BD_NOFEP	0x5
-#define	BD_FAILED	0x6
-#define BD_ALLOCATED	0x7
-#define BD_TRIBOOT	0x8
-#define	BD_BADKME	0x80
-
-#define DIGI_SPOLL            (('d'<<8) | 254)  /* change poller rate   */
 
 #define DIGI_SETCUSTOMBAUD	_IOW('e', 106, int)	/* Set integer baud rate */
 #define DIGI_GETCUSTOMBAUD	_IOR('e', 107, int)	/* Get integer baud rate */
@@ -390,20 +167,8 @@ struct digi_getcounter {
 
 #define EV_OPU		0x0001		/* !<Output paused by client */
 #define EV_OPS		0x0002		/* !<Output paused by reqular sw flowctrl */
-#define EV_OPX		0x0004		/* !<Output paused by extra sw flowctrl */
-#define EV_OPH		0x0008		/* !<Output paused by hw flowctrl */
-#define EV_OPT		0x0800		/* !<Output paused for RTS Toggle predelay */
-
 #define EV_IPU		0x0010		/* !<Input paused unconditionally by user */
 #define EV_IPS		0x0020		/* !<Input paused by high/low water marks */
-#define EV_IPA		0x0400		/* !<Input paused by pattern alarm module */
-
 #define EV_TXB		0x0040		/* !<Transmit break pending */
-#define EV_TXI		0x0080		/* !<Transmit immediate pending */
-#define EV_TXF		0x0100		/* !<Transmit flowctrl char pending */
-#define EV_RXB		0x0200		/* !<Break received */
-
-#define EV_OPALL	0x080f		/* !<Output pause flags */
-#define EV_IPALL	0x0430		/* !<Input pause flags */
 
 #endif /* DIGI_H */
Signature · 1 line
2.3.2
#1 lore raw

PATCH 2/6 dgnc: get rid of dpacompat.h, move remaining stuff to digi.h

Dpacompat.h contained a lot of unused #defines and only few things are used from it so since we've trimmed down digi.h, now we can delete dpacompat.h and move remaining stuff into digi.h.

---
 drivers/staging/dgnc/dgnc_driver.c |   1 -
 drivers/staging/dgnc/dgnc_mgmt.c   |   1 -
 drivers/staging/dgnc/dgnc_tty.c    |   1 -
 drivers/staging/dgnc/digi.h        |  36 ++++++++++++
 drivers/staging/dgnc/dpacompat.h   | 109 -------------------------------------
 5 files changed, 36 insertions(+), 112 deletions(-)
 delete mode 100644 drivers/staging/dgnc/dpacompat.h
drivers/staging/dgnc/dgnc_driver.c +0 -1
index 9ae9014..805dc61 100644
@@ -21,7 +21,6 @@
 #include <linux/sched.h>
 #include "dgnc_driver.h"
 #include "dgnc_pci.h"
-#include "dpacompat.h"
 #include "dgnc_mgmt.h"
 #include "dgnc_tty.h"
 #include "dgnc_cls.h"
drivers/staging/dgnc/dgnc_mgmt.c +0 -1
index 5781406..1a00eac 100644
@@ -32,7 +32,6 @@
 #include "dgnc_pci.h"
 #include "dgnc_kcompat.h"	/* Kernel 2.4/2.6 compat includes */
 #include "dgnc_mgmt.h"
-#include "dpacompat.h"
 
 
 /* Our "in use" variables, to enforce 1 open only */
drivers/staging/dgnc/dgnc_tty.c +0 -1
index 8445f84..1085d4c 100644
@@ -39,7 +39,6 @@
 #include "dgnc_types.h"
 #include "dgnc_neo.h"
 #include "dgnc_cls.h"
-#include "dpacompat.h"
 #include "dgnc_sysfs.h"
 #include "dgnc_utils.h"
 
drivers/staging/dgnc/digi.h +36 -0
index 7e5e6b0..277648f 100644
@@ -44,6 +44,11 @@
 #define DIGI_SETA	(('e'<<8) | 95)		/* Set params		*/
 #define DIGI_SETAW	(('e'<<8) | 96)		/* Drain & set params	*/
 #define DIGI_SETAF	(('e'<<8) | 97)		/* Drain, flush & set params */
+#define DIGI_GET_NI_INFO (('d'<<8) | 250) /* Non-intelligent state info */
+#define DIGI_LOOPBACK (('d'<<8) | 252) /*
+					* Enable/disable UART
+					* internal loopback
+					*/
 #define DIGI_FAST	0x0002		/* Fast baud rates		*/
 #define RTSPACE		0x0004		/* RTS input flow control	*/
 #define CTSPACE		0x0008		/* CTS output flow control	*/
@@ -171,4 +176,35 @@ struct digi_getcounter {
 #define EV_IPS		0x0020		/* !<Input paused by high/low water marks */
 #define EV_TXB		0x0040		/* !<Transmit break pending */
 
+/*
+ * This structure holds data needed for the intelligent <--> nonintelligent
+ * DPA translation
+ */
+struct ni_info {
+	int board;
+	int channel;
+	int dtr;
+	int rts;
+	int cts;
+	int dsr;
+	int ri;
+	int dcd;
+	int curtx;
+	int currx;
+	unsigned short iflag;
+	unsigned short oflag;
+	unsigned short cflag;
+	unsigned short lflag;
+	unsigned int mstat;
+	unsigned char hflow;
+	unsigned char xmit_stopped;
+	unsigned char recv_stopped;
+	unsigned int baud;
+};
+
+#define T_CLASSIC 0002
+#define T_PCIBUS 0400
+#define T_NEO_EXPRESS 0001
+#define T_NEO 0000
+
 #endif /* DIGI_H */
drivers/staging/dgnc/dpacompat.h deleted +0 -109

109 lines not on this page · raw message

Signature · 1 line
2.3.2
#2 lore raw

PATCH 3/6 dgnc: convert TRUE/FALSE #defines to 1/0

In reply to Giedrius Statkevičius

TRUE/FALSE defined in dgnc_types.h are only used in dgnc_tty.c thus it would be better to just use 1/0 to avoid unnecessary extra files and includes.

---
 drivers/staging/dgnc/dgnc_cls.h    |  3 ---
 drivers/staging/dgnc/dgnc_driver.h |  1 -
 drivers/staging/dgnc/dgnc_neo.h    |  1 -
 drivers/staging/dgnc/dgnc_tty.c    |  9 ++++-----
 drivers/staging/dgnc/dgnc_types.h  | 27 ---------------------------
 5 files changed, 4 insertions(+), 37 deletions(-)
 delete mode 100644 drivers/staging/dgnc/dgnc_types.h
drivers/staging/dgnc/dgnc_cls.h +0 -3
index 2398514..85042bd 100644
@@ -16,9 +16,6 @@
 #ifndef __DGNC_CLS_H
 #define __DGNC_CLS_H
 
-#include "dgnc_types.h"
-
-
 /************************************************************************
  * Per channel/port Classic UART structure				*
  ************************************************************************
drivers/staging/dgnc/dgnc_driver.h +0 -1
index 15c4d95..f28329d 100644
@@ -25,7 +25,6 @@
 #include <linux/tty.h>	  /* To pick up the various tty structs/defines */
 #include <linux/interrupt.h>	/* For irqreturn_t type */
 
-#include "dgnc_types.h"		/* Additional types needed by the Digi header files */
 #include "digi.h"		/* Digi specific ioctl header */
 #include "dgnc_kcompat.h"	/* Kernel 2.4/2.6 compat includes */
 #include "dgnc_sysfs.h"		/* Support for SYSFS */
drivers/staging/dgnc/dgnc_neo.h +0 -1
index d7e764a..c528df5 100644
@@ -16,7 +16,6 @@
 #ifndef __DGNC_NEO_H
 #define __DGNC_NEO_H
 
-#include "dgnc_types.h"
 #include "dgnc_driver.h"
 
 /************************************************************************
drivers/staging/dgnc/dgnc_tty.c +4 -5
index 1085d4c..f8f9374 100644
@@ -36,7 +36,6 @@
 #include <linux/pci.h>
 #include "dgnc_driver.h"
 #include "dgnc_tty.h"
-#include "dgnc_types.h"
 #include "dgnc_neo.h"
 #include "dgnc_cls.h"
 #include "dgnc_sysfs.h"
@@ -220,7 +219,7 @@ int dgnc_tty_register(struct dgnc_board *brd)
 				"Can't register tty device (%d)\n", rc);
 			return rc;
 		}
-		brd->dgnc_Major_Serial_Registered = TRUE;
+		brd->dgnc_Major_Serial_Registered = 1;
 	}
 
 	/*
@@ -270,7 +269,7 @@ int dgnc_tty_register(struct dgnc_board *brd)
 				rc);
 			return rc;
 		}
-		brd->dgnc_Major_TransparentPrint_Registered = TRUE;
+		brd->dgnc_Major_TransparentPrint_Registered = 1;
 	}
 
 	dgnc_BoardsByMajor[brd->SerialDriver.major] = brd;
@@ -408,7 +407,7 @@ void dgnc_tty_uninit(struct dgnc_board *brd)
 			tty_unregister_device(&brd->SerialDriver, i);
 		}
 		tty_unregister_driver(&brd->SerialDriver);
-		brd->dgnc_Major_Serial_Registered = FALSE;
+		brd->dgnc_Major_Serial_Registered = 0;
 	}
 
 	if (brd->dgnc_Major_TransparentPrint_Registered) {
@@ -419,7 +418,7 @@ void dgnc_tty_uninit(struct dgnc_board *brd)
 			tty_unregister_device(&brd->PrintDriver, i);
 		}
 		tty_unregister_driver(&brd->PrintDriver);
-		brd->dgnc_Major_TransparentPrint_Registered = FALSE;
+		brd->dgnc_Major_TransparentPrint_Registered = 0;
 	}
 
 	kfree(brd->SerialDriver.ttys);
drivers/staging/dgnc/dgnc_types.h deleted +0 -27
deleted file mode 100644
index 2853d16..0000000
@@ -1,27 +0,0 @@
-/*
- * Copyright 2003 Digi International (www.digi.com)
- *	Scott H Kilau <Scott_Kilau at digi dot com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED; without even the
- * implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
- * PURPOSE.  See the GNU General Public License for more details.
- */
-
-#ifndef __DGNC_TYPES_H
-#define __DGNC_TYPES_H
-
-#ifndef TRUE
-# define TRUE 1
-#endif
-
-#ifndef FALSE
-# define FALSE 0
-#endif
-
-#endif
Signature · 1 line
2.3.2
#3 lore raw

Re: [PATCH 3/6] dgnc: convert TRUE/FALSE #defines to 1/0

Quoted 4 lines · Giedrius Statkevičius

TRUE/FALSE defined in dgnc_types.h are only used in dgnc_tty.c thus it would be better to just use 1/0 to avoid unnecessary extra files and includes.

Use true/false. I don't care much about this personally but true/false is kernel style these days.

regards,
dan carpenter

#4 lore raw

Re: [PATCH 3/6] dgnc: convert TRUE/FALSE #defines to 1/0

Quoted 6 lines · Dan Carpenter
Quoted 4 lines · Giedrius Statkevičius

TRUE/FALSE defined in dgnc_types.h are only used in dgnc_tty.c thus it would be better to just use 1/0 to avoid unnecessary extra files and includes.

Quoted 6 lines

Use true/false. I don't care much about this personally but true/false is kernel style these days.

regards,
dan carpenter

After researching more this whole dgnc_Major_Serial_Registered and dgnc_Major_TransparentPrint_Registered seem pretty pointless because they only get set to true or false depending on if those boards are initialised or not and we won't initialise them two or more times - dgnc_init_one() is a probe method and it's never called anywhere else. This seems like a way better solution - redundant stuff will be removed from the struct and a unnecessary header will be removed (types.h is for bools) :) I'll fix this up in v2 but now I'll wait for more comments on other patches (if there will be any) for a bit.

Signature · 2 lines
Thanks,
Giedrius
#5 lore raw

PATCH 4/6 dgnc: remove old 2.4-2.6 compat kernel defines

In reply to Giedrius Statkevičius

dgnc_kcompat.h contains some old legacy defines in case the kernel doesn't have __user defined but for current kernel versions these defines don't make sense and are useless so remove them. Move the TTY_FLIPBUF_SIZE define to digi.h because it's used in the code.

---
 drivers/staging/dgnc/dgnc_driver.h  |  1 -
 drivers/staging/dgnc/dgnc_kcompat.h | 40 -------------------------------------
 drivers/staging/dgnc/dgnc_mgmt.c    |  1 -
 drivers/staging/dgnc/digi.h         |  1 +
 4 files changed, 1 insertion(+), 42 deletions(-)
 delete mode 100644 drivers/staging/dgnc/dgnc_kcompat.h
drivers/staging/dgnc/dgnc_driver.h +0 -1
index f28329d..cf472a3 100644
@@ -26,7 +26,6 @@
 #include <linux/interrupt.h>	/* For irqreturn_t type */
 
 #include "digi.h"		/* Digi specific ioctl header */
-#include "dgnc_kcompat.h"	/* Kernel 2.4/2.6 compat includes */
 #include "dgnc_sysfs.h"		/* Support for SYSFS */
 
 /*************************************************************************
drivers/staging/dgnc/dgnc_kcompat.h deleted +0 -40
deleted file mode 100644
index 2206038..0000000
@@ -1,40 +0,0 @@
-/*
- * Copyright 2004 Digi International (www.digi.com)
- *      Scott H Kilau <Scott_Kilau at digi dot com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED; without even the
- * implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
- * PURPOSE.  See the GNU General Public License for more details.
- *
- *************************************************************************
- *
- * This file is intended to contain all the kernel "differences" between the
- * various kernels that we support.
- *
- *************************************************************************/
-
-#ifndef __DGNC_KCOMPAT_H
-#define __DGNC_KCOMPAT_H
-
-#if !defined(TTY_FLIPBUF_SIZE)
-# define TTY_FLIPBUF_SIZE 512
-#endif
-
-
-/* Sparse stuff */
-# ifndef __user
-#  define __user
-#  define __kernel
-#  define __safe
-#  define __force
-#  define __chk_user_ptr(x) (void)0
-# endif
-
-
-#endif /* ! __DGNC_KCOMPAT_H */
drivers/staging/dgnc/dgnc_mgmt.c +0 -1
index 1a00eac..d0e22c1 100644
@@ -30,7 +30,6 @@
 
 #include "dgnc_driver.h"
 #include "dgnc_pci.h"
-#include "dgnc_kcompat.h"	/* Kernel 2.4/2.6 compat includes */
 #include "dgnc_mgmt.h"
 
 
drivers/staging/dgnc/digi.h +1 -0
index 277648f..9611dd5 100644
@@ -207,4 +207,5 @@ struct ni_info {
 #define T_NEO_EXPRESS 0001
 #define T_NEO 0000
 
+#define TTY_FLIPBUF_SIZE 512
 #endif /* DIGI_H */
Signature · 1 line
2.3.2
#6 lore raw

PATCH 5/6 dgnc: remove unused stuff from dgnc_cls.h

In reply to Giedrius Statkevičius

Remove unused defines from dgnc_cls.h

---
 drivers/staging/dgnc/dgnc_cls.h | 13 -------------
 1 file changed, 13 deletions(-)
drivers/staging/dgnc/dgnc_cls.h +0 -13
index 85042bd..2597e36 100644
@@ -51,15 +51,9 @@ struct cls_uart_struct {
 
 #define UART_EXAR654_ENHANCED_REGISTER_SET 0xBF
 
-#define UART_16654_FCR_TXTRIGGER_8	0x0
 #define UART_16654_FCR_TXTRIGGER_16	0x10
-#define UART_16654_FCR_TXTRIGGER_32	0x20
-#define UART_16654_FCR_TXTRIGGER_56	0x30
-
-#define UART_16654_FCR_RXTRIGGER_8	0x0
 #define UART_16654_FCR_RXTRIGGER_16	0x40
 #define UART_16654_FCR_RXTRIGGER_56	0x80
-#define UART_16654_FCR_RXTRIGGER_60     0xC0
 
 /* Received CTS/RTS change of state */
 #define UART_IIR_CTSRTS			0x20
@@ -76,13 +70,6 @@ struct cls_uart_struct {
 #define UART_EXAR654_EFR_IXOFF    0x8     /* Transmit Xon1/Xoff1 */
 #define UART_EXAR654_EFR_RTSDTR   0x40    /* Auto RTS/DTR Flow Control Enable */
 #define UART_EXAR654_EFR_CTSDSR   0x80    /* Auto CTS/DSR Flow COntrol Enable */
-
-/* Indicates whether chip saw an incoming XOFF char  */
-#define UART_EXAR654_XOFF_DETECT  0x1
-
-/* Indicates whether chip saw an incoming XON char */
-#define UART_EXAR654_XON_DETECT   0x2
-
 #define UART_EXAR654_IER_XOFF     0x20    /* Xoff Interrupt Enable */
 #define UART_EXAR654_IER_RTSDTR   0x40    /* Output Interrupt Enable */
 #define UART_EXAR654_IER_CTSDSR   0x80    /* Input Interrupt Enable */
Signature · 1 line
2.3.2
#7 lore raw

PATCH 6/6 dgnc: Clean up dgnc_sysfs.h

In reply to Giedrius Statkevičius

Remove redundant blank lines, move absolute include after relative include.

---
 drivers/staging/dgnc/dgnc_sysfs.h | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/staging/dgnc/dgnc_sysfs.h +1 -4
index 2758914..be0f90a 100644
@@ -16,9 +16,8 @@
 #ifndef __DGNC_SYSFS_H
 #define __DGNC_SYSFS_H
 
-#include "dgnc_driver.h"
-
 #include <linux/device.h>
+#include "dgnc_driver.h"
 
 struct dgnc_board;
 struct channel_t;
@@ -38,6 +37,4 @@ extern int dgnc_tty_class_destroy(void);
 extern void dgnc_create_tty_sysfs(struct un_t *un, struct device *c);
 extern void dgnc_remove_tty_sysfs(struct device *c);
 
-
-
 #endif
Signature · 1 line
2.3.2