SA1100 RTC clean-up for ARM64

index 3543466..b598db6 100644
@@ -439,25 +439,11 @@ struct platform_device pxa_device_rtc = {
 	.resource       = pxa_rtc_resources,
 };
 
-static struct resource sa1100_rtc_resources[] = {
-	{
-		.start  = IRQ_RTC1Hz,
-		.end    = IRQ_RTC1Hz,
-		.name	= "rtc 1Hz",
-		.flags  = IORESOURCE_IRQ,
-	}, {
-		.start  = IRQ_RTCAlrm,
-		.end    = IRQ_RTCAlrm,
-		.name	= "rtc alarm",
-		.flags  = IORESOURCE_IRQ,
-	},
-};
-
 struct platform_device sa1100_device_rtc = {
 	.name		= "sa1100-rtc",
 	.id		= -1,
-	.num_resources	= ARRAY_SIZE(sa1100_rtc_resources),
-	.resource	= sa1100_rtc_resources,
+	.num_resources  = ARRAY_SIZE(pxa_rtc_resources),
+	.resource       = pxa_rtc_resources,
 };
 
 static struct resource pxa_ac97_resources[] = {

index b6e1ca0..a21ead5 100644
@@ -35,12 +35,10 @@
 #include <linux/bitops.h>
 #include <linux/io.h>
 
-#include <mach/hardware.h>
-#include <mach/irqs.h>
-
-#if defined(CONFIG_ARCH_PXA) || defined(CONFIG_ARCH_MMP)
-#include <mach/regs-rtc.h>
-#endif
+#define RTSR_HZE	(1 << 3)	/* HZ interrupt enable */
+#define RTSR_ALE	(1 << 2)	/* RTC alarm interrupt enable */
+#define RTSR_HZ		(1 << 1)	/* HZ rising-edge detected */
+#define RTSR_AL		(1 << 0)	/* RTC alarm detected */
 
 #define RTC_DEF_DIVIDER		(32768 - 1)
 #define RTC_DEF_TRIM		0

@@ -48,6 +46,10 @@
 
 struct sa1100_rtc {
 	spinlock_t		lock;
+	void __iomem		*rcnr;
+	void __iomem		*rtar;
+	void __iomem		*rtsr;
+	void __iomem		*rttr;
 	int			irq_1hz;
 	int			irq_alarm;
 	struct rtc_device	*rtc;

@@ -63,16 +65,16 @@ static irqreturn_t sa1100_rtc_interrupt(int irq, void *dev_id)
 
 	spin_lock(&info->lock);
 
-	rtsr = RTSR;
+	rtsr = readl_relaxed(info->rtsr);
 	/* clear interrupt sources */
-	RTSR = 0;
+	writel_relaxed(0, info->rtsr);
 	/* Fix for a nasty initialization problem the in SA11xx RTSR register.
 	 * See also the comments in sa1100_rtc_probe(). */
 	if (rtsr & (RTSR_ALE | RTSR_HZE)) {
 		/* This is the original code, before there was the if test
 		 * above. This code does not clear interrupts that were not
 		 * enabled. */
-		RTSR = (RTSR_AL | RTSR_HZ) & (rtsr >> 2);
+		writel_relaxed((RTSR_AL | RTSR_HZ) & (rtsr >> 2), info->rtsr);
 	} else {
 		/* For some reason, it is possible to enter this routine
 		 * without interruptions enabled, it has been tested with

@@ -81,13 +83,13 @@ static irqreturn_t sa1100_rtc_interrupt(int irq, void *dev_id)
 		 * This situation leads to an infinite "loop" of interrupt
 		 * routine calling and as a result the processor seems to
 		 * lock on its first call to open(). */
-		RTSR = RTSR_AL | RTSR_HZ;
+		writel_relaxed(RTSR_AL | RTSR_HZ, info->rtsr);
 	}
 
 	/* clear alarm interrupt if it has occurred */
 	if (rtsr & RTSR_AL)
 		rtsr &= ~RTSR_ALE;
-	RTSR = rtsr & (RTSR_ALE | RTSR_HZE);
+	writel_relaxed(rtsr & (RTSR_ALE | RTSR_HZE), info->rtsr);
 
 	/* update irq data & counter */
 	if (rtsr & RTSR_AL)

@@ -135,7 +137,7 @@ static void sa1100_rtc_release(struct device *dev)
 	struct sa1100_rtc *info = dev_get_drvdata(dev);
 
 	spin_lock_irq(&info->lock);
-	RTSR = 0;
+	writel_relaxed(0, info->rtsr);
 	spin_unlock_irq(&info->lock);
 
 	free_irq(info->irq_alarm, dev);

@@ -144,39 +146,45 @@ static void sa1100_rtc_release(struct device *dev)
 
 static int sa1100_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled)
 {
+	u32 rtsr;
 	struct sa1100_rtc *info = dev_get_drvdata(dev);
 
 	spin_lock_irq(&info->lock);
+	rtsr = readl_relaxed(info->rtsr);
 	if (enabled)
-		RTSR |= RTSR_ALE;
+		rtsr |= RTSR_ALE;
 	else
-		RTSR &= ~RTSR_ALE;
+		rtsr &= ~RTSR_ALE;
+	writel_relaxed(rtsr, info->rtsr);
 	spin_unlock_irq(&info->lock);
 	return 0;
 }
 
 static int sa1100_rtc_read_time(struct device *dev, struct rtc_time *tm)
 {
-	rtc_time_to_tm(RCNR, tm);
+	struct sa1100_rtc *info = dev_get_drvdata(dev);
+	rtc_time_to_tm(readl_relaxed(info->rcnr), tm);
 	return 0;
 }
 
 static int sa1100_rtc_set_time(struct device *dev, struct rtc_time *tm)
 {
+	struct sa1100_rtc *info = dev_get_drvdata(dev);
 	unsigned long time;
 	int ret;
 
 	ret = rtc_tm_to_time(tm, &time);
 	if (ret == 0)
-		RCNR = time;
+		writel_relaxed(time, info->rcnr);
 	return ret;
 }
 
 static int sa1100_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
 {
 	u32	rtsr;
+	struct sa1100_rtc *info = dev_get_drvdata(dev);
 
-	rtsr = RTSR;
+	rtsr = readl_relaxed(info->rtsr);
 	alrm->enabled = (rtsr & RTSR_ALE) ? 1 : 0;
 	alrm->pending = (rtsr & RTSR_AL) ? 1 : 0;
 	return 0;

@@ -192,12 +200,13 @@ static int sa1100_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
 	ret = rtc_tm_to_time(&alrm->time, &time);
 	if (ret != 0)
 		goto out;
-	RTSR = RTSR & (RTSR_HZE|RTSR_ALE|RTSR_AL);
-	RTAR = time;
+	writel_relaxed(readl_relaxed(info->rtsr) &
+		(RTSR_HZE | RTSR_ALE | RTSR_AL), info->rtsr);
+	writel_relaxed(time, info->rtar);
 	if (alrm->enabled)
-		RTSR |= RTSR_ALE;
+		writel_relaxed(readl_relaxed(info->rtsr) | RTSR_ALE, info->rtsr);
 	else
-		RTSR &= ~RTSR_ALE;
+		writel_relaxed(readl_relaxed(info->rtsr) & ~RTSR_ALE, info->rtsr);
 out:
 	spin_unlock_irq(&info->lock);
 

@@ -206,8 +215,9 @@ out:
 
 static int sa1100_rtc_proc(struct device *dev, struct seq_file *seq)
 {
-	seq_printf(seq, "trim/divider\t\t: 0x%08x\n", (u32) RTTR);
-	seq_printf(seq, "RTSR\t\t\t: 0x%08x\n", (u32)RTSR);
+	struct sa1100_rtc *info = dev_get_drvdata(dev);
+	seq_printf(seq, "trim/divider\t\t: 0x%08x\n", readl_relaxed(info->rttr));
+	seq_printf(seq, "RTSR\t\t\t: 0x%08x\n", readl_relaxed(info->rtsr));
 
 	return 0;
 }

@@ -227,6 +237,8 @@ static int sa1100_rtc_probe(struct platform_device *pdev)
 {
 	struct rtc_device *rtc;
 	struct sa1100_rtc *info;
+	struct resource *iores;
+	void __iomem *base;
 	int irq_1hz, irq_alarm, ret = 0;
 
 	irq_1hz = platform_get_irq_byname(pdev, "rtc 1Hz");

@@ -244,6 +256,26 @@ static int sa1100_rtc_probe(struct platform_device *pdev)
 	}
 	info->irq_1hz = irq_1hz;
 	info->irq_alarm = irq_alarm;
+
+
+	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(&pdev->dev, iores);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	if (IS_ENABLED(CONFIG_ARCH_SA1100) ||
+	    of_device_is_compatible(pdev->dev.of_node, "mrvl,sa1100-rtc")) {
+		info->rcnr = base + 0x04;
+		info->rtsr = base + 0x10;
+		info->rtar = base + 0x00;
+		info->rttr = base + 0x08;
+	} else {
+		info->rcnr = base + 0x0;
+		info->rtsr = base + 0x8;
+		info->rtar = base + 0x4;
+		info->rttr = base + 0xc;
+	}
+
 	spin_lock_init(&info->lock);
 	platform_set_drvdata(pdev, info);
 

@@ -257,12 +289,12 @@ static int sa1100_rtc_probe(struct platform_device *pdev)
 	 * If the clock divider is uninitialized then reset it to the
 	 * default value to get the 1Hz clock.
 	 */
-	if (RTTR == 0) {
-		RTTR = RTC_DEF_DIVIDER + (RTC_DEF_TRIM << 16);
+	if (readl_relaxed(info->rttr) == 0) {
+		writel_relaxed(RTC_DEF_DIVIDER + (RTC_DEF_TRIM << 16), info->rttr);
 		dev_warn(&pdev->dev, "warning: "
 			"initializing default clock divider/trim value\n");
 		/* The current RTC value probably doesn't make sense either */
-		RCNR = 0;
+		writel_relaxed(0, info->rcnr);
 	}
 
 	device_init_wakeup(&pdev->dev, 1);

@@ -298,7 +330,7 @@ static int sa1100_rtc_probe(struct platform_device *pdev)
 	 *
 	 * Notice that clearing bit 1 and 0 is accomplished by writting ONES to
 	 * the corresponding bits in RTSR. */
-	RTSR = RTSR_AL | RTSR_HZ;
+	writel_relaxed(RTSR_AL | RTSR_HZ, info->rtsr);
 
 	return 0;
 err_dev:

index 0ac6cc0..7972617 100644
@@ -858,40 +858,6 @@
 
 
 /*
- * Real-Time Clock (RTC) control registers
- *
- * Registers
- *    RTAR      	Real-Time Clock (RTC) Alarm Register (read/write).
- *    RCNR      	Real-Time Clock (RTC) CouNt Register (read/write).
- *    RTTR      	Real-Time Clock (RTC) Trim Register (read/write).
- *    RTSR      	Real-Time Clock (RTC) Status Register (read/write).
- *
- * Clocks
- *    frtx, Trtx	Frequency, period of the real-time clock crystal
- *              	(32.768 kHz nominal).
- *    frtc, Trtc	Frequency, period of the real-time clock counter
- *              	(1 Hz nominal).
- */
-
-#define RTAR		__REG(0x90010000)  /* RTC Alarm Reg. */
-#define RCNR		__REG(0x90010004)  /* RTC CouNt Reg. */
-#define RTTR		__REG(0x90010008)  /* RTC Trim Reg. */
-#define RTSR		__REG(0x90010010)  /* RTC Status Reg. */
-
-#define RTTR_C  	Fld (16, 0)	/* clock divider Count - 1         */
-#define RTTR_D  	Fld (10, 16)	/* trim Delete count               */
-                	        	/* frtc = (1023*(C + 1) - D)*frtx/ */
-                	        	/*        (1023*(C + 1)^2)         */
-                	        	/* Trtc = (1023*(C + 1)^2)*Trtx/   */
-                	        	/*        (1023*(C + 1) - D)       */
-
-#define RTSR_AL 	0x00000001	/* ALarm detected                  */
-#define RTSR_HZ 	0x00000002	/* 1 Hz clock detected             */
-#define RTSR_ALE	0x00000004	/* ALarm interrupt Enable          */
-#define RTSR_HZE	0x00000008	/* 1 Hz clock interrupt Enable     */
-
-
-/*
  * Power Manager (PM) control registers
  *
  * Registers

deleted file mode 100644
index 5bff886..0000000
@@ -1,23 +0,0 @@
-#ifndef __ASM_MACH_REGS_RTC_H
-#define __ASM_MACH_REGS_RTC_H
-
-#include <mach/addr-map.h>
-
-#define RTC_VIRT_BASE	(APB_VIRT_BASE + 0x10000)
-#define RTC_REG(x)	(*((volatile u32 __iomem *)(RTC_VIRT_BASE + (x))))
-
-/*
- * Real Time Clock
- */
-
-#define RCNR		RTC_REG(0x00)	/* RTC Count Register */
-#define RTAR		RTC_REG(0x04)	/* RTC Alarm Register */
-#define RTSR		RTC_REG(0x08)	/* RTC Status Register */
-#define RTTR		RTC_REG(0x0C)	/* RTC Timer Trim Register */
-
-#define RTSR_HZE	(1 << 3)	/* HZ interrupt enable */
-#define RTSR_ALE	(1 << 2)	/* RTC alarm interrupt enable */
-#define RTSR_HZ		(1 << 1)	/* HZ rising-edge detected */
-#define RTSR_AL		(1 << 0)	/* RTC alarm detected */
-
-#endif /* __ASM_MACH_REGS_RTC_H */