Skip to contentSkip to conversation

hw/misc/zynq_slcr: Change CPU clock rate

PATCH Superseded Guenter Roeck 2 participants 4 messages Aug 12, 2015 – Sep 11, 2015 Arm/Zynq architecture

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 hw/misc/zynq_slcr: Change CPU clock rate

The Linux kernel only accepts 333334 Khz and 666667 Khz clock rates, and may crash if the actual clock rate is too low. The clock rate used to be (ps-clk-frequency * 26 / 4), which resulted in a CPU frequency of 216666 Khz if ps-clk-frequency was set to 33333333 Hz. Change it to (ps-clk-frequency * 20 / 2) = 333333 Khz to make Linux happy.

---
 hw/misc/zynq_slcr.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
hw/misc/zynq_slcr.c +2 -2
index 964f253..d3e1ce0 100644
@@ -189,7 +189,7 @@ static void zynq_slcr_reset(DeviceState *d)
 
     s->regs[LOCKSTA] = 1;
     /* 0x100 - 0x11C */
-    s->regs[ARM_PLL_CTRL]   = 0x0001A008;
+    s->regs[ARM_PLL_CTRL]   = 0x00014008;
     s->regs[DDR_PLL_CTRL]   = 0x0001A008;
     s->regs[IO_PLL_CTRL]    = 0x0001A008;
     s->regs[PLL_STATUS]     = 0x0000003F;
@@ -198,7 +198,7 @@ static void zynq_slcr_reset(DeviceState *d)
     s->regs[IO_PLL_CFG]     = 0x00014000;
 
     /* 0x120 - 0x16C */
-    s->regs[ARM_CLK_CTRL]   = 0x1F000400;
+    s->regs[ARM_CLK_CTRL]   = 0x1F000200;
     s->regs[DDR_CLK_CTRL]   = 0x18400003;
     s->regs[DCI_CLK_CTRL]   = 0x01E03201;
     s->regs[APER_CLK_CTRL]  = 0x01FFCCCD;
Signature · 1 line
2.1.4
#1 lore raw
Quoted 6 lines · Guenter Roeck

The Linux kernel only accepts 333334 Khz and 666667 Khz clock rates, and may crash if the actual clock rate is too low. The clock rate used to be (ps-clk-frequency * 26 / 4), which resulted in a CPU frequency of 216666 Khz if ps-clk-frequency was set to 33333333 Hz. Change it to (ps-clk-frequency * 20 / 2) = 333333 Khz to make Linux happy.

This is a long known problem that is solved via patch in the yocto meta-layer via a similar hack to slcr.

Ideally SLCR should follow the TRM reset value by default and this is really setting up post bootloader state.

But PMM recently upstreamed the needed core patches to have a device register Linux specific setup:

Search for:

"hw/arm: new interface for devices which need to behave differently for kernel boot"

and following patches that show how we can achieve best of both words, with Linux specific device setup as well keep the ability to boot raw (for testing firmware such as FSBL itself).

Regards,
Peter

P.S. Sorry about the delay (and to PMM on missed review of that series). I dropped off the radar for a month or so July->Aug.

Quoted 31 lines
---
 hw/misc/zynq_slcr.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
hw/misc/zynq_slcr.c +2 -3
index 964f253..d3e1ce0 100644
@@ -189,7 +189,7 @@ static void zynq_slcr_reset(DeviceState *d)
 
     s->regs[LOCKSTA] = 1;
     /* 0x100 - 0x11C */
-    s->regs[ARM_PLL_CTRL]   = 0x0001A008;
+    s->regs[ARM_PLL_CTRL]   = 0x00014008;
     s->regs[DDR_PLL_CTRL]   = 0x0001A008;
     s->regs[IO_PLL_CTRL]    = 0x0001A008;
     s->regs[PLL_STATUS]     = 0x0000003F;
@@ -198,7 +198,7 @@ static void zynq_slcr_reset(DeviceState *d)
     s->regs[IO_PLL_CFG]     = 0x00014000;
 
     /* 0x120 - 0x16C */
-    s->regs[ARM_CLK_CTRL]   = 0x1F000400;
+    s->regs[ARM_CLK_CTRL]   = 0x1F000200;
     s->regs[DDR_CLK_CTRL]   = 0x18400003;
     s->regs[DCI_CLK_CTRL]   = 0x01E03201;
     s->regs[APER_CLK_CTRL]  = 0x01FFCCCD;
--

2.1.4

#2 lore raw

Hi Peter,

Quoted 11 lines · Peter Crosthwaite
Quoted 6 lines · Guenter Roeck

The Linux kernel only accepts 333334 Khz and 666667 Khz clock rates, and may crash if the actual clock rate is too low. The clock rate used to be (ps-clk-frequency * 26 / 4), which resulted in a CPU frequency of 216666 Khz if ps-clk-frequency was set to 33333333 Hz. Change it to (ps-clk-frequency * 20 / 2) = 333333 Khz to make Linux happy.

This is a long known problem that is solved via patch in the yocto meta-layer via a similar hack to slcr.

Doesn't sound like a solution to me :-(.

Quoted 3 lines

Ideally SLCR should follow the TRM reset value by default and this is really setting up post bootloader state.

Which sclr ? The Linux driver ?

Quoted 12 lines

But PMM recently upstreamed the needed core patches to have a device register Linux specific setup:

Search for:

"hw/arm: new interface for devices which need to behave differently for kernel boot"

and following patches that show how we can achieve best of both words, with Linux specific device setup as well keep the ability to boot raw (for testing firmware such as FSBL itself).

So what would be the correct solution here ? Implement the arm_linux_init callback for this driver, which would set the register values below, or some other acceptable register values ?

Or something else ?

Quoted 6 lines

Regards,
Peter

P.S. Sorry about the delay (and to PMM on missed review of that series). I dropped off the radar for a month or so July->Aug.

No worries.

Thanks,
Guenter

Quoted 31 lines
Quoted 31 lines
---
 hw/misc/zynq_slcr.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
hw/misc/zynq_slcr.c +2 -3
index 964f253..d3e1ce0 100644
@@ -189,7 +189,7 @@ static void zynq_slcr_reset(DeviceState *d)
 
     s->regs[LOCKSTA] = 1;
     /* 0x100 - 0x11C */
-    s->regs[ARM_PLL_CTRL]   = 0x0001A008;
+    s->regs[ARM_PLL_CTRL]   = 0x00014008;
     s->regs[DDR_PLL_CTRL]   = 0x0001A008;
     s->regs[IO_PLL_CTRL]    = 0x0001A008;
     s->regs[PLL_STATUS]     = 0x0000003F;
@@ -198,7 +198,7 @@ static void zynq_slcr_reset(DeviceState *d)
     s->regs[IO_PLL_CFG]     = 0x00014000;
 
     /* 0x120 - 0x16C */
-    s->regs[ARM_CLK_CTRL]   = 0x1F000400;
+    s->regs[ARM_CLK_CTRL]   = 0x1F000200;
     s->regs[DDR_CLK_CTRL]   = 0x18400003;
     s->regs[DCI_CLK_CTRL]   = 0x01E03201;
     s->regs[APER_CLK_CTRL]  = 0x01FFCCCD;
--

2.1.4

#3 lore raw
Quoted 11 lines · Guenter Roeck

Hi Peter,

Quoted 8 lines · Peter Crosthwaite
Quoted 6 lines · Guenter Roeck

The Linux kernel only accepts 333334 Khz and 666667 Khz clock rates, and may crash if the actual clock rate is too low. The clock rate used to be (ps-clk-frequency * 26 / 4), which resulted in a CPU frequency of 216666 Khz if ps-clk-frequency was set to 33333333 Hz. Change it to (ps-clk-frequency * 20 / 2) = 333333 Khz to make Linux happy.

Quoted 5 lines
Quoted 3 lines

This is a long known problem that is solved via patch in the yocto meta-layer via a similar hack to slcr.

Doesn't sound like a solution to me :-(.

It's not :)

Quoted 5 lines
Quoted 3 lines

Ideally SLCR should follow the TRM reset value by default and this is really setting up post bootloader state.

Which sclr ? The Linux driver ?

No I mean this QEMU device model. It would be nice if the Kernel was able to deal with absent clocking (perhaps configured via DTS?) but in reality I think we have to work around this from the QEMU side. We just need to make your changes in this patch Linux specific rather than absolute.

Quoted 8 lines
Quoted 8 lines

But PMM recently upstreamed the needed core patches to have a device register Linux specific setup:

Search for:

"hw/arm: new interface for devices which need to behave differently for kernel boot"

Quoted 8 lines
Quoted 4 lines

and following patches that show how we can achieve best of both words, with Linux specific device setup as well keep the ability to boot raw (for testing firmware such as FSBL itself).

So what would be the correct solution here ? Implement the arm_linux_init callback for this driver, which would set the register values below, or some other acceptable register values ?

Yes I think so.

Regards,
Peter

Quoted 44 lines

Or something else ?

Quoted 6 lines

Regards,
Peter

P.S. Sorry about the delay (and to PMM on missed review of that series). I dropped off the radar for a month or so July->Aug.

No worries.

Thanks,
Guenter

Quoted 31 lines
Quoted 31 lines
---
 hw/misc/zynq_slcr.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
hw/misc/zynq_slcr.c +2 -3
index 964f253..d3e1ce0 100644
@@ -189,7 +189,7 @@ static void zynq_slcr_reset(DeviceState *d)
 
     s->regs[LOCKSTA] = 1;
     /* 0x100 - 0x11C */
-    s->regs[ARM_PLL_CTRL]   = 0x0001A008;
+    s->regs[ARM_PLL_CTRL]   = 0x00014008;
     s->regs[DDR_PLL_CTRL]   = 0x0001A008;
     s->regs[IO_PLL_CTRL]    = 0x0001A008;
     s->regs[PLL_STATUS]     = 0x0000003F;
@@ -198,7 +198,7 @@ static void zynq_slcr_reset(DeviceState *d)
     s->regs[IO_PLL_CFG]     = 0x00014000;
 
     /* 0x120 - 0x16C */
-    s->regs[ARM_CLK_CTRL]   = 0x1F000400;
+    s->regs[ARM_CLK_CTRL]   = 0x1F000200;
     s->regs[DDR_CLK_CTRL]   = 0x18400003;
     s->regs[DCI_CLK_CTRL]   = 0x01E03201;
     s->regs[APER_CLK_CTRL]  = 0x01FFCCCD;
--

2.1.4