Batch submission via GuC
Subsystems (3)
v6 cover Batch submission via GuC
This patch series enables command submission via the GuC. In this mode, instead of the host CPU driving the execlist port directly, it hands over work items to the GuC, using a doorbell mechanism to tell the GuC that new items have been added to its work queue. The GuC then dispatches contexts to the various GPU engines, and manages the resulting context- switch interrupts. Completion of a batch is however still signalled to the CPU; the GuC is not involved in handling user interrupts.
There are two subsequences within the patch series:
drm/i915: GuC-specific firmware loader drm/i915: Debugfs interface to read GuC load status
These two patches provide the GuC loader and a debugfs interface to verify the resulting state. At this point in the sequence we can load and activate the GuC firmware, but not submit any batches through it. (This is nonetheless a potentially useful state, as the GuC could do other useful work even when not handling batch submissions).
drm/i915: Expose one LRC function for GuC submission mode drm/i915: Prepare for GuC-based command submission drm/i915: Enable GuC firmware log
drm/i915: Implementation of GuC submission client drm/i915: Interrupt routing for GuC submission drm/i915: Integrate GuC-based command submission drm/i915: Debugfs interface for GuC submission statistics
In this second section, we implement the GuC submission mechanism, and link it into the (execlist-based) submission path. At this stage, it is not yet enabled by default; it is activated only if the kernel command line explicitly switches it on.
The GuC firmware itself is not included in this patchset; it is or will be available for download from https://01.org/linuxgraphics/downloads/
This driver works with and requires GuC firmware revision 3.x. It will not work with any firmware version 1.x, as the GuC protocol in those revisions was incompatible and is no longer supported.
On platforms where there is no GuC, or where GuC submission is not specifically enabled, batch submission will continue to use the execlist (or ringbuffer) mechanisms. On the other hand, if GuC submission is requested but the GuC firmware cannot be found or is invalid, the GPU will be unusable.
It is expected that a subsequent patch will enable GuC submission by default once the signed firmware is published on 01.org.
Ben Widawsky (0):
Vinit Azad (0):
Michael H. Nguyen (0):
created the original versions on which some of these patches are based.
Alex Dai (5):
drm/i915: GuC-specific firmware loader drm/i915: Debugfs interface to read GuC load status drm/i915: Prepare for GuC-based command submission drm/i915: Enable GuC firmware log
drm/i915: Integrate GuC-based command submission
Dave Gordon (4):
drm/i915: Expose one LRC function for GuC submission mode drm/i915: Implementation of GuC submission client drm/i915: Interrupt routing for GuC submission drm/i915: Debugfs interface for GuC submission statistics
Documentation/DocBook/drm.tmpl | 14 + drivers/gpu/drm/i915/Makefile | 4 + drivers/gpu/drm/i915/i915_debugfs.c | 146 ++++- drivers/gpu/drm/i915/i915_dma.c | 9 + drivers/gpu/drm/i915/i915_drv.h | 11 + drivers/gpu/drm/i915/i915_gem.c | 16 + drivers/gpu/drm/i915/i915_gpu_error.c | 14 +- drivers/gpu/drm/i915/i915_guc_reg.h | 17 +- drivers/gpu/drm/i915/i915_guc_submission.c | 901 +++++++++++++++++++++++++++++ drivers/gpu/drm/i915/i915_reg.h | 15 +- drivers/gpu/drm/i915/intel_guc.h | 122 ++++ drivers/gpu/drm/i915/intel_guc_fwif.h | 9 +- drivers/gpu/drm/i915/intel_guc_loader.c | 611 +++++++++++++++++++ drivers/gpu/drm/i915/intel_lrc.c | 65 ++- drivers/gpu/drm/i915/intel_lrc.h | 8 + 15 files changed, 1918 insertions(+), 44 deletions(-) create mode 100644 drivers/gpu/drm/i915/i915_guc_submission.c create mode 100644 drivers/gpu/drm/i915/intel_guc.h create mode 100644 drivers/gpu/drm/i915/intel_guc_loader.c
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 1/9 drm/i915: GuC-specific firmware loader
From: Alex Dai <[email protected]>
This fetches the required firmware image from the filesystem, then loads it into the GuC's memory via a dedicated DMA engine.
This patch is derived from GuC loading work originally done by Vinit Azad and Ben Widawsky.
v2:
Various improvements per review comments by Chris Wilson
v3:
Removed 'wait' parameter to intel_guc_ucode_load() as firmware
prefetch is no longer supported in the common firmware loader, per Daniel Vetter's request.
Firmware checker callback fn now returns errno rather than bool.
v4:
Squash uC-independent code into GuC-specifc loader [Daniel Vetter] Don't keep the driver working (by falling back to execlist mode)
if GuC firmware loading fails [Daniel Vetter]
v5:
Clarify WOPCM-related #defines [Tom O'Rourke] Delete obsolete code no longer required with current h/w & f/w
[Tom O'Rourke]
Move the call to intel_guc_ucode_init() later, so that it can
allocate GEM objects, and have it fetch the firmware; then intel_guc_ucode_load() doesn't need to fetch it later. [Daniel Vetter].
v6:
Update comment describing intel_guc_ucode_load() [Tom O'Rourke]
Issue: VIZ-4884
--- drivers/gpu/drm/i915/Makefile | 3 + drivers/gpu/drm/i915/i915_dma.c | 9 + drivers/gpu/drm/i915/i915_drv.h | 11 + drivers/gpu/drm/i915/i915_gem.c | 16 + drivers/gpu/drm/i915/i915_guc_reg.h | 17 +- drivers/gpu/drm/i915/i915_reg.h | 4 +- drivers/gpu/drm/i915/intel_guc.h | 67 ++++ drivers/gpu/drm/i915/intel_guc_fwif.h | 3 +- drivers/gpu/drm/i915/intel_guc_loader.c | 529 ++++++++++++++++++++++++++++++++ 9 files changed, 650 insertions(+), 9 deletions(-) create mode 100644 drivers/gpu/drm/i915/intel_guc.h create mode 100644 drivers/gpu/drm/i915/intel_guc_loader.c
drivers/gpu/drm/i915/Makefile +3 -0
@@ -40,6 +40,9 @@ i915-y += i915_cmd_parser.o \ intel_ringbuffer.o \ intel_uncore.o +# general-purpose microcontroller (GuC) support +i915-y += intel_guc_loader.o + # autogenerated null render state i915-y += intel_renderstate_gen6.o \ intel_renderstate_gen7.o \
drivers/gpu/drm/i915/i915_dma.c +9 -0
@@ -435,6 +435,11 @@ static int i915_load_modeset_init(struct drm_device *dev)* working irqs for e.g. gmbus and dp aux transfers. */ intel_modeset_init (dev); +/* intel_guc_ucode_init() needs the mutex to allocate GEM objects */ +mutex_lock (&dev->struct_mutex); +intel_guc_ucode_init (dev); +mutex_unlock (&dev->struct_mutex); + ret =i915_gem_init (dev);if (ret) goto cleanup_irq;
@@ -476,6 +481,9 @@ cleanup_gem:i915_gem_context_fini (dev);mutex_unlock (&dev->struct_mutex); cleanup_irq: +mutex_lock (&dev->struct_mutex); +intel_guc_ucode_fini (dev); +mutex_unlock (&dev->struct_mutex);drm_irq_uninstall (dev); cleanup_gem_stolen:i915_gem_cleanup_stolen (dev);
@@ -1128,6 +1136,7 @@ int i915_driver_unload(struct drm_device *dev)flush_workqueue (dev_priv->wq);mutex_lock (&dev->struct_mutex); +intel_guc_ucode_fini (dev);i915_gem_cleanup_ringbuffer (dev);i915_gem_context_fini (dev);mutex_unlock (&dev->struct_mutex);
drivers/gpu/drm/i915/i915_drv.h +11 -0
@@ -50,6 +50,7 @@#include <linux/intel-iommu.h> #include <linux/kref.h> #include <linux/pm_qos.h> +#include "intel_guc.h" /* General customization: */
@@ -1706,6 +1707,8 @@ struct drm_i915_private {struct i915_virtual_gpu vgpu; +struct intel_guc guc; +struct intel_csr csr;/* Display CSR-related protection */
@@ -1950,6 +1953,11 @@ static inline struct drm_i915_private *dev_to_i915(struct device *dev)return to_i915 (dev_get_drvdata (dev)); } +static inline struct drm_i915_private *guc_to_i915 (struct intel_guc *guc) +{ + return container_of(guc, struct drm_i915_private, guc); +} +/* Iterate over initialised rings */ #define for_each_ring (ring__, dev_priv__, i__) \ for ((i__) = 0; (i__) < I915_NUM_RINGS; (i__)++) \
@@ -2554,6 +2562,9 @@ struct drm_i915_cmd_table {#define HAS_CSR (dev) (IS_SKYLAKE(dev)) +#define HAS_GUC_UCODE (dev) (IS_GEN9(dev)) +#define HAS_GUC_SCHED (dev) (IS_GEN9(dev)) +#define HAS_RESOURCE_STREAMER (dev) (IS_HASWELL(dev) || \ INTEL_INFO(dev)->gen >= 8)
drivers/gpu/drm/i915/i915_gem.c +16 -0
@@ -4680,6 +4680,22 @@ i915_gem_init_hw(struct drm_device *dev) goto out; } +/* We can't enable contexts until all firmware is loaded */ + ret =intel_guc_ucode_load (dev); +if (ret) { +/* +* If we got an error and GuC submission is enabled, map +* the error to -EIO so the GPU will be declared wedged. +* OTOH, if we didn't intend to use the GuC anyway, just +* discard the error and carry on. +*/ +DRM_ERROR ("Failed to initialize GuC, error %d%s\n" , ret, + i915.enable_guc_submission ?"" :" (ignored)" ); + ret = i915.enable_guc_submission ? -EIO :0 ; +if (ret) + goto out; + } +/* Now it is safe to go back round and do everything else: */ for_each_ring (ring, dev_priv, i) {struct drm_i915_gem_request *req;
drivers/gpu/drm/i915/i915_guc_reg.h +11 -6
@@ -38,10 +38,6 @@#define GS_MIA_SHIFT 16#define GS_MIA_MASK (0x07 << GS_MIA_SHIFT) -#define GUC_WOPCM_SIZE 0xc050 -#define GUC_WOPCM_SIZE_VALUE (0x80 << 12)/* 512KB */ -#define GUC_WOPCM_OFFSET 0x80000/* 512KB */ -#define SOFT_SCRATCH (n) (0xc180 + ((n) * 4))#define UOS_RSA_SCRATCH_0 0xc200
@@ -56,10 +52,18 @@#define UOS_MOVE (1<<4)#define START_DMA (1<<0)#define DMA_GUC_WOPCM_OFFSET 0xc340 +#define GUC_WOPCM_OFFSET_VALUE 0x80000/* 512KB */ + +#define GUC_WOPCM_SIZE 0xc050 +#define GUC_WOPCM_SIZE_VALUE (0x80 << 12)/* 512KB */ + +/* GuC addresses below GUC_WOPCM_TOP don't map through the GTT */ +#define GUC_WOPCM_TOP (GUC_WOPCM_SIZE_VALUE)#define GEN8_GT_PM_CONFIG 0x138140 +#define GEN9LP_GT_PM_CONFIG 0x138140#define GEN9_GT_PM_CONFIG 0x13816c -#define GEN8_GT_DOORBELL_ENABLE (1<<0) +#define GT_DOORBELL_ENABLE (1<<0)#define GEN8_GTCR 0x4274#define GEN8_GTCR_INVALIDATE (1<<0)
@@ -80,7 +84,8 @@ GUC_ENABLE_READ_CACHE_LOGIC | \ GUC_ENABLE_MIA_CACHING | \ GUC_ENABLE_READ_CACHE_FOR_SRAM_DATA | \ - GUC_ENABLE_READ_CACHE_FOR_WOPCM_DATA) + GUC_ENABLE_READ_CACHE_FOR_WOPCM_DATA | \ + GUC_ENABLE_MIA_CLOCK_GATING)#define HOST2GUC_INTERRUPT 0xc4c8#define HOST2GUC_TRIGGER (1<<0)
drivers/gpu/drm/i915/i915_reg.h +3 -1
@@ -6871,7 +6871,9 @@ enum skl_disp_power_wells {#define GEN9_PGCTL_SSB_EU311_ACK (1 << 14)#define GEN7_MISCCPCTL (0x9424) -#define GEN7_DOP_CLOCK_GATE_ENABLE (1<<0) +#define GEN7_DOP_CLOCK_GATE_ENABLE (1<<0) +#define GEN8_DOP_CLOCK_GATE_CFCLK_ENABLE (1<<2) +#define GEN8_DOP_CLOCK_GATE_GUC_ENABLE (1<<4)#define GEN8_GARBCNTL 0xB004#define GEN9_GAPS_TSV_CREDIT_DISABLE (1<<7)
drivers/gpu/drm/i915/intel_guc.h new file +67 -0
67 lines not on this page · raw message
drivers/gpu/drm/i915/intel_guc_fwif.h +1 -2
@@ -32,9 +32,8 @@* EDITING THIS FILE IS THEREFORE NOT RECOMMENDED - YOUR CHANGES MAY BE LOST. */ -#define GFXCORE_FAMILY_GEN8 11#define GFXCORE_FAMILY_GEN9 12 -#define GFXCORE_FAMILY_FORCE_ULONG 0x7fffffff +#define GFXCORE_FAMILY_UNKNOWN 0x7fffffff#define GUC_CTX_PRIORITY_CRITICAL 0#define GUC_CTX_PRIORITY_HIGH 1
drivers/gpu/drm/i915/intel_guc_loader.c new file +529 -0
529 lines not on this page · raw message
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 1/9 v6] drm/i915: GuC-specific firmware loader
Quoted 31 lines · Dave Gordon
From: Alex Dai <[email protected]>
This fetches the required firmware image from the filesystem, then loads it into the GuC's memory via a dedicated DMA engine.
This patch is derived from GuC loading work originally done by Vinit Azad and Ben Widawsky.
v2:
Various improvements per review comments by Chris Wilsonv3:
Removed 'wait' parameter tointel_guc_ucode_load()as firmware
prefetch is no longer supported in the common firmware loader, per Daniel Vetter's request.
Firmware checker callback fn now returns errno rather than bool.v4:
Squash uC-independent code into GuC-specifc loader [Daniel Vetter] Don't keep the driver working (by falling back to execlist mode)
if GuC firmware loading fails [Daniel Vetter]v5:
Clarify WOPCM-related #defines [Tom O'Rourke] Delete obsolete code no longer required with current h/w & f/w
[Tom O'Rourke]
Move the call tointel_guc_ucode_init()later, so that it can
allocate GEM objects, and have it fetch the firmware; thenintel_guc_ucode_load()doesn't need to fetch it later. [Daniel Vetter].
Quoted 6 lines
v6:
Update comment describingintel_guc_ucode_load()[Tom O'Rourke]Issue: VIZ-4884
Signed-off-by Alex Dai <[email protected]>Signed-off-by Dave Gordon <[email protected]>
Checkpatch was pretty unhappy with long lines and alignment of continuations. But didn't look too bad overall so pulled it in.
Quoted 14 lines
+/*
+ * Transfer the firmware image to RAM for execution by the microcontroller.
+ *
+ * GuC Firmware layout:
+ * +-------------------------------+ ----+ * | CSS header | 128B + * | contains major/minor version | + * +-------------------------------+ ---- + * | uCode | + * +-------------------------------+ ---- + * | RSA signature | 256B + * +-------------------------------+ ---- + * | RSA public Key | 256B + * +-------------------------------+ ----
Quoted 9 lines
+ * | Public key modulus | 4B
+ * +-------------------------------+ ----
+ *
+ * Architecturally, the DMA engine is bidirectional, and can potentially even
+ * transfer between GTT locations. This functionality is left out of the API
+ * for now as there is no need for it.
+ *
+ * Note that GuC needs the CSS header plus uKernel code to be copied by the
+ * DMA engine in one operation, whereas the RSA signature is loaded via MMIO.
Imo this should be included in the kerneldoc too, especially now that we can handle tables with markdown.
-Daniel
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 2/9 drm/i915: Debugfs interface to read GuC load status
In reply to Dave GordonFrom: Alex Dai <[email protected]>
The new node provides access to the status of the GuC-specific loader; also the scratch registers used for communication between the i915 driver and the GuC firmware.
v2:
Changes to output formats per Chris Wilson's suggestions
v6:
Rebased
Issue: VIZ-4884
--- drivers/gpu/drm/i915/i915_debugfs.c | 39 +++++++++++++++++++++++++++++++++++++ 1 file changed, 39 insertions(+)
drivers/gpu/drm/i915/i915_debugfs.c +39 -0
@@ -2374,6 +2374,44 @@ static int i915_llc(struct seq_file *m, void *data)return 0 ; } +static int i915_guc_load_status_info (struct seq_file *m,void *data) +{ +struct drm_info_node *node = m->private; +struct drm_i915_private *dev_priv = node->minor->dev->dev_private; +struct intel_guc_fw *guc_fw = &dev_priv->guc.guc_fw; +u32 tmp, i; + +if (!HAS_GUC_UCODE (dev_priv->dev)) +return 0 ; + +seq_printf (m,"GuC firmware status:\n" ); +seq_printf (m,"\tpath: %s\n" , + guc_fw->guc_fw_path); +seq_printf (m,"\tfetch: %s\n" , +intel_guc_fw_status_repr (guc_fw->guc_fw_fetch_status)); +seq_printf (m,"\tload: %s\n" , +intel_guc_fw_status_repr (guc_fw->guc_fw_load_status)); +seq_printf (m,"\tversion wanted: %d.%d\n" , + guc_fw->guc_fw_major_wanted, guc_fw->guc_fw_minor_wanted); +seq_printf (m,"\tversion found: %d.%d\n" , + guc_fw->guc_fw_major_found, guc_fw->guc_fw_minor_found); + + tmp =I915_READ (GUC_STATUS ); + +seq_printf (m,"\nGuC status 0x%08x:\n" , tmp); +seq_printf (m,"\tBootrom status = 0x%x\n" , + (tmp &GS_BOOTROM_MASK ) >>GS_BOOTROM_SHIFT ); +seq_printf (m,"\tuKernel status = 0x%x\n" , + (tmp &GS_UKERNEL_MASK ) >>GS_UKERNEL_SHIFT ); +seq_printf (m,"\tMIA Core status = 0x%x\n" , + (tmp &GS_MIA_MASK ) >>GS_MIA_SHIFT ); +seq_puts (m,"\nScratch registers:\n" ); +for (i =0 ; i <16 ; i++) +seq_printf (m,"\t%2d: \t0x%x\n" , i,I915_READ (SOFT_SCRATCH (i))); + +return 0 ; +} +static int i915_edp_psr_status (struct seq_file *m,void *data) {struct drm_info_node *node = m->private;
@@ -5033,6 +5071,7 @@ static const struct drm_info_list i915_debugfs_list[] = { {"i915_gem_hws_bsd", i915_hws_info, 0, (void *)VCS}, {"i915_gem_hws_vebox", i915_hws_info, 0, (void *)VECS}, {"i915_gem_batch_pool", i915_gem_batch_pool_info, 0}, + {"i915_guc_load_status", i915_guc_load_status_info, 0}, {"i915_frequency_info", i915_frequency_info, 0}, {"i915_hangcheck_info", i915_hangcheck_info, 0}, {"i915_drpc_info", i915_drpc_info, 0},
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 3/9 drm/i915: Expose one LRC function for GuC submission mode
In reply to Dave GordonGuC submission is basically execlist submission, but with the GuC handling the actual writes to the ELSP and the resulting context switch interrupts. So to describe a context for submission via the GuC, we need one of the same functions used in execlist mode. This commit exposes one such function, changing its name to better describe what it does (it's related to logical ring contexts rather than to execlists per se).
v2:
Replaces previous "drm/i915: Move execlists defines from .c to .h"
v3:
Incorporates a change to one of the functions exposed here that was
previously part of an internal patch, but which was omitted from the version recently committed to drm-intel-nightly:
7a01a0a drm/i915/lrc: Update PDPx registers with lri commands
So we reinstate this change here.
v4:
Drop v3 change, update function parameters due to collision with
8ee3615 drm/i915: Convert execlists_ctx_descriptor() for requests
v5:
Don't expose execlists_update_context() after all. The current
version is no longer compatible with GuC submission; trying to share the execlist version of this function results in both GuC and CPU updating TAIL in the context image, with bad results when they get out of step. The GuC submission path now has its own private version that just updates the ringbuffer start address, and not TAIL or PDPx.
v6:
Rebased
Issue: VIZ-4884
--- drivers/gpu/drm/i915/intel_lrc.c | 10 +++++----- drivers/gpu/drm/i915/intel_lrc.h | 2 ++ 2 files changed, 7 insertions(+), 5 deletions(-)
drivers/gpu/drm/i915/intel_lrc.c +5 -5
@@ -270,11 +270,11 @@ u32 intel_execlists_ctx_id(struct drm_i915_gem_object *ctx_obj)return lrca >>12 ; } -static uint64_t execlists_ctx_descriptor (struct drm_i915_gem_request *rq) +uint64_t intel_lr_context_descriptor (struct intel_context *ctx, +struct intel_engine_cs *ring) { -struct intel_engine_cs *ring = rq->ring;struct drm_device *dev = ring->dev; -struct drm_i915_gem_object *ctx_obj = rq->ctx->engine[ring->id].state; +struct drm_i915_gem_object *ctx_obj = ctx->engine[ring->id].state;uint64_t desc;uint64_t lrca =i915_gem_obj_ggtt_offset (ctx_obj);
@@ -312,13 +312,13 @@ static void execlists_elsp_write(struct drm_i915_gem_request *rq0,uint64_t desc[2 ];if (rq1) { - desc[1 ] =execlists_ctx_descriptor (rq1); + desc[1 ] =intel_lr_context_descriptor (rq1->ctx, rq1->ring); rq1->elsp_submitted++; }else { desc[1 ] =0 ; } - desc[0 ] =execlists_ctx_descriptor (rq0); + desc[0 ] =intel_lr_context_descriptor (rq0->ctx, rq0->ring); rq0->elsp_submitted++;/* You must always write both descriptors in the order below. */
drivers/gpu/drm/i915/intel_lrc.h +2 -0
@@ -74,6 +74,8 @@ int intel_lr_context_deferred_create(struct intel_context *ctx,void intel_lr_context_unpin (struct drm_i915_gem_request *req);void intel_lr_context_reset (struct drm_device *dev,struct intel_context *ctx); +uint64_t intel_lr_context_descriptor (struct intel_context *ctx, +struct intel_engine_cs *ring);/* Execlists */ int intel_sanitize_enable_execlists (struct drm_device *dev,int enable_execlists);
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 4/9 drm/i915: Prepare for GuC-based command submission
In reply to Dave GordonFrom: Alex Dai <[email protected]>
This adds the first of the data structures used to communicate with the GuC (the pool of guc_context structures).
We create a GuC-specific wrapper round the GEM object allocator as all GEM objects shared with the GuC must be pinned into GGTT space at an address that is NOT in the range [0..WOPCM_TOP), as that range of GGTT addresses is not accessible to the GuC (from the GuC's point of view, it's permanently reserved for other objects such as the BootROM & SRAM).
Later, we will need to allocate additional GuC-sharable objects for the submission client(s) and the GuC's debug log.
v2:
Remove redundant initialisation [Chris Wilson]
Defer adding struct members until needed [Chris Wilson] Local functions should pass dev_priv rather than dev [Chris Wilson]
v5:
Invalidate GuC TLB after allocating and pinning a new object
v6:
Rebased
Issue: VIZ-4884
--- drivers/gpu/drm/i915/Makefile | 3 +- drivers/gpu/drm/i915/i915_guc_submission.c | 118 +++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_guc.h | 7 ++ drivers/gpu/drm/i915/intel_guc_loader.c | 21 +++++ 4 files changed, 148 insertions(+), 1 deletion(-) create mode 100644 drivers/gpu/drm/i915/i915_guc_submission.c
drivers/gpu/drm/i915/Makefile +2 -1
@@ -41,7 +41,8 @@ i915-y += i915_cmd_parser.o \ intel_uncore.o # general-purpose microcontroller (GuC) support -i915-y += intel_guc_loader.o +i915-y += intel_guc_loader.o \ + i915_guc_submission.o # autogenerated null render state i915-y += intel_renderstate_gen6.o \
drivers/gpu/drm/i915/i915_guc_submission.c new file +118 -0
118 lines not on this page · raw message
drivers/gpu/drm/i915/intel_guc.h +7 -0
@@ -56,6 +56,9 @@ struct intel_guc {struct intel_guc_fw guc_fw;uint32_t log_flags; + +struct drm_i915_gem_object *ctx_pool_obj; +struct ida ctx_ids; };/* intel_guc_loader.c */
@@ -64,4 +67,8 @@ extern int intel_guc_ucode_load(struct drm_device *dev);extern void intel_guc_ucode_fini (struct drm_device *dev);extern const char *intel_guc_fw_status_repr (enum intel_guc_fw_status status); +/* i915_guc_submission.c */ +int i915_guc_submission_init (struct drm_device *dev); +void i915_guc_submission_fini (struct drm_device *dev); +#endif
drivers/gpu/drm/i915/intel_guc_loader.c +21 -0
@@ -128,6 +128,21 @@ static void set_guc_init_params(struct drm_i915_private *dev_priv) i915.guc_log_level <<GUC_LOG_VERBOSITY_SHIFT ; } +/* If GuC submission is enabled, set up additional parameters here */ +if (i915.enable_guc_submission) { +u32 pgs =i915_gem_obj_ggtt_offset (dev_priv->guc.ctx_pool_obj); +u32 ctx_in_16 =GUC_MAX_GPU_CONTEXTS /16 ; + + pgs >>=PAGE_SHIFT ; + params[GUC_CTL_CTXINFO ] = (pgs <<GUC_CTL_BASE_ADDR_SHIFT ) | + (ctx_in_16 <<GUC_CTL_CTXNUM_IN16_SHIFT ); + + params[GUC_CTL_FEATURE ] |=GUC_CTL_KERNEL_SUBMISSIONS ; + +/* Unmask this bit to enable the GuC's internal scheduler */ + params[GUC_CTL_FEATURE ] &= ~GUC_CTL_DISABLE_SCHEDULER ; + } +I915_WRITE (SOFT_SCRATCH (0 ),0 );for (i =0 ; i <GUC_CTL_MAX_DWORDS ; i++)
@@ -360,6 +375,10 @@ int intel_guc_ucode_load(struct drm_device *dev)break ; } + err =i915_guc_submission_init (dev); +if (err) + goto fail; + err =guc_ucode_xfer (dev_priv);if (err) goto fail;
@@ -521,6 +540,8 @@ void intel_guc_ucode_fini(struct drm_device *dev)struct drm_i915_private *dev_priv = dev->dev_private;struct intel_guc_fw *guc_fw = &dev_priv->guc.guc_fw; +i915_guc_submission_fini (dev); +if (guc_fw->guc_fw_obj)drm_gem_object_unreference (&guc_fw->guc_fw_obj->base); guc_fw->guc_fw_obj =NULL ;
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 5/9 drm/i915: Enable GuC firmware log
In reply to Dave GordonFrom: Alex Dai <[email protected]>
Allocate a GEM object to hold GuC log data. A debugfs interface (i915_guc_log_dump) is provided to print out the log content.
v2:
Add struct members at point of use [Chris Wilson]
v6:
Rebased
Issue: VIZ-4884
--- drivers/gpu/drm/i915/i915_debugfs.c | 29 +++++++++++++++++++ drivers/gpu/drm/i915/i915_guc_submission.c | 46 ++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_guc.h | 1 + 3 files changed, 76 insertions(+)
drivers/gpu/drm/i915/i915_debugfs.c +29 -0
@@ -2412,6 +2412,34 @@ static int i915_guc_load_status_info(struct seq_file *m, void *data)return 0 ; } +static int i915_guc_log_dump (struct seq_file *m,void *data) +{ +struct drm_info_node *node = m->private; +struct drm_device *dev = node->minor->dev; +struct drm_i915_private *dev_priv = dev->dev_private; +struct drm_i915_gem_object *log_obj = dev_priv->guc.log_obj; +u32 *log; +int i =0 , pg; + +if (!log_obj) +return 0 ; + +for (pg =0 ; pg < log_obj->base.size /PAGE_SIZE ; pg++) { + log =kmap_atomic (i915_gem_object_get_page (log_obj, pg)); + +for (i =0 ; i <PAGE_SIZE /sizeof (u32); i +=4 ) +seq_printf (m,"0x%08x 0x%08x 0x%08x 0x%08x\n" , + *(log + i), *(log + i +1 ), + *(log + i +2 ), *(log + i +3 )); + +kunmap_atomic (log); + } + +seq_putc (m,'\n' ); + +return 0 ; +} +static int i915_edp_psr_status (struct seq_file *m,void *data) {struct drm_info_node *node = m->private;
@@ -5072,6 +5100,7 @@ static const struct drm_info_list i915_debugfs_list[] = { {"i915_gem_hws_vebox", i915_hws_info, 0, (void *)VECS}, {"i915_gem_batch_pool", i915_gem_batch_pool_info, 0}, {"i915_guc_load_status", i915_guc_load_status_info, 0}, + {"i915_guc_log_dump", i915_guc_log_dump, 0}, {"i915_frequency_info", i915_frequency_info, 0}, {"i915_hangcheck_info", i915_hangcheck_info, 0}, {"i915_drpc_info", i915_drpc_info, 0},
drivers/gpu/drm/i915/i915_guc_submission.c +46 -0
64 lines not on this page · raw message
drivers/gpu/drm/i915/intel_guc.h +1 -0
@@ -56,6 +56,7 @@ struct intel_guc {struct intel_guc_fw guc_fw;uint32_t log_flags; +struct drm_i915_gem_object *log_obj;struct drm_i915_gem_object *ctx_pool_obj;struct ida ctx_ids;
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 6/9 drm/i915: Implementation of GuC submission client
In reply to Dave GordonA GuC client has its own doorbell and workqueue. It maintains the doorbell cache line, process description object and work queue item.
A default guc_client is created for the i915 driver to use for normal-priority in-order submission.
Note that the created client is not yet ready for use; doorbell allocation will fail as we haven't yet linked the GuC's context descriptor to the default contexts for each ring (see later patch).
v2:
Defer adding structure members until needed [Chris Wilson] Rationalise type declarations [Chris Wilson]
v5:
Add GuC per-engine submission & seqno statistics. Move wq locking to encompass both get_space() and add_item(). Take forcewake lock in host2guc_action() [Tom O'Rourke]
v6:
Fix GuC doorbell cacheline selection code (the
cacheline-within-page calculation was wrong).
Rename GuC priorities to make them closer to the names used in
the GuC firmware source, matching what the autogenerated versions will (probably) be.
Add per-ring statistics to client.
Issue: VIZ-4884
--- drivers/gpu/drm/i915/i915_guc_submission.c | 666 +++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_guc.h | 46 ++ drivers/gpu/drm/i915/intel_guc_fwif.h | 6 +- drivers/gpu/drm/i915/intel_guc_loader.c | 10 + 4 files changed, 725 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/i915_guc_submission.c +666 -0
@@ -27,6 +27,529 @@#include "intel_guc.h" /** +* DOC: GuC Client +* +* i915_guc_client: +* We use the term client to avoid confusion with contexts. A i915_guc_client is +* equivalent to GuC object guc_context_desc. This context descriptor is +* allocated from a pool of 1024 entries. Kernel driver will allocate doorbell +* and workqueue for it. Also the process descriptor (guc_process_desc), which +* is mapped to client space. So the client can write Work Item then ring the +* doorbell. +* +* To simplify the implementation, we allocate one gem object that contains all +* pages for doorbell, process descriptor and workqueue. +* +* The Scratch registers: +* There are 16 MMIO-based registers start from 0xC180. The kernel driver writes +* a value to the action register (SOFT_SCRATCH_0) along with any data. It then +* triggers an interrupt on the GuC via another register write (0xC4C8). +* Firmware writes a success/fail code back to the action register after +* processes the request. The kernel driver polls waiting for this update and +* then proceeds. +* See host2guc_action() +* +* Doorbells: +* Doorbells are interrupts to uKernel. A doorbell is a single cache line (QW) +* mapped into process space. +* +* Work Items: +* There are several types of work items that the host may place into a +* workqueue, each with its own requirements and limitations. Currently only +* WQ_TYPE_INORDER is needed to support legacy submission via GuC, which +* represents in-order queue. The kernel driver packs ring tail pointer and an +* ELSP context descriptor dword into Work Item. +* See guc_add_workqueue_item() +* +*/ + +/* +* Read GuC command/status register (SOFT_SCRATCH_0) +* Return true if it contains a response rather than a command +*/ +static inline bool host2guc_action_response (struct drm_i915_private *dev_priv, +u32 *status) +{ +u32 val =I915_READ (SOFT_SCRATCH (0 )); + *status = val; +return GUC2HOST_IS_RESPONSE (val); +} + +static int host2guc_action (struct intel_guc *guc,u32 *data,u32 len) +{ +struct drm_i915_private *dev_priv =guc_to_i915 (guc); +u32 status; +int i; +int ret; + +if (WARN_ON (len <1 || len >15 )) +return -EINVAL ; + +intel_uncore_forcewake_get (dev_priv,FORCEWAKE_ALL ); +spin_lock (&dev_priv->guc.host2guc_lock); + + dev_priv->guc.action_count +=1 ; + dev_priv->guc.action_cmd = data[0 ]; + +for (i =0 ; i < len; i++) +I915_WRITE (SOFT_SCRATCH (i), data[i]); + +POSTING_READ (SOFT_SCRATCH (i -1 )); + +I915_WRITE (HOST2GUC_INTERRUPT ,HOST2GUC_TRIGGER ); + +/* No HOST2GUC command should take longer than 10ms */ + ret =wait_for_atomic (host2guc_action_response (dev_priv, &status),10 ); +if (status !=GUC2HOST_STATUS_SUCCESS ) { +/* +* Either the GuC explicitly returned an error (which +* we convert to -EIO here) or no response at all was +* received within the timeout limit (-ETIMEDOUT) +*/ +if (ret != -ETIMEDOUT ) + ret = -EIO ; + +DRM_ERROR ("GUC: host2guc action 0x%X failed. ret=%d " +"status=0x%08X response=0x%08X\n" , + data[0 ], ret, status, +I915_READ (SOFT_SCRATCH (15 ))); + + dev_priv->guc.action_fail +=1 ; + dev_priv->guc.action_err = ret; + } + dev_priv->guc.action_status = status; + +spin_unlock (&dev_priv->guc.host2guc_lock); +intel_uncore_forcewake_put (dev_priv,FORCEWAKE_ALL ); + +return ret; +} + +/* +* Tell the GuC to allocate or deallocate a specific doorbell +*/ + +static int host2guc_allocate_doorbell (struct intel_guc *guc, +struct i915_guc_client *client) +{ +u32 data[2 ]; + + data[0 ] =HOST2GUC_ACTION_ALLOCATE_DOORBELL ; + data[1 ] = client->ctx_index; + +return host2guc_action (guc, data,2 ); +} + +static int host2guc_release_doorbell (struct intel_guc *guc, +struct i915_guc_client *client) +{ +u32 data[2 ]; + + data[0 ] =HOST2GUC_ACTION_DEALLOCATE_DOORBELL ; + data[1 ] = client->ctx_index; + +return host2guc_action (guc, data,2 ); +} + +/* +* Initialise, update, or clear doorbell data shared with the GuC +* +* These functions modify shared data and so need access to the mapped +* client object which contains the page being used for the doorbell +*/ + +static void guc_init_doorbell (struct intel_guc *guc, +struct i915_guc_client *client) +{ +struct guc_doorbell_info *doorbell; +void *base; + + base =kmap_atomic (i915_gem_object_get_page (client->client_obj,0 )); + doorbell = base + client->doorbell_offset; + + doorbell->db_status =1 ; + doorbell->cookie =0 ; + +kunmap_atomic (base); +} + +static int guc_ring_doorbell (struct i915_guc_client *gc) +{ +struct guc_process_desc *desc; +union guc_doorbell_qw db_cmp, db_exc, db_ret; +union guc_doorbell_qw *db; +void *base; +int attempt =2 , ret = -EAGAIN ; + + base =kmap_atomic (i915_gem_object_get_page (gc->client_obj,0 )); + desc = base + gc->proc_desc_offset; + +/* Update the tail so it is visible to GuC */ + desc->tail = gc->wq_tail; + +/* current cookie */ + db_cmp.db_status =GUC_DOORBELL_ENABLED ; + db_cmp.cookie = gc->cookie; + +/* cookie to be updated */ + db_exc.db_status =GUC_DOORBELL_ENABLED ; + db_exc.cookie = gc->cookie +1 ; +if (db_exc.cookie ==0 ) + db_exc.cookie =1 ; + +/* pointer of current doorbell cacheline */ + db = base + gc->doorbell_offset; + +while (attempt--) { +/* lets ring the doorbell */ + db_ret.value_qw =atomic64_cmpxchg ((atomic64_t *)db, + db_cmp.value_qw, db_exc.value_qw); + +/* if the exchange was successfully executed */ +if (db_ret.value_qw == db_cmp.value_qw) { +/* db was successfully rung */ + gc->cookie = db_exc.cookie; + ret =0 ; +break ; + } + +/* XXX: doorbell was lost and need to acquire it again */ +if (db_ret.db_status ==GUC_DOORBELL_DISABLED ) +break ; + +DRM_ERROR ("Cookie mismatch. Expected %d, returned %d\n" , + db_cmp.cookie, db_ret.cookie); + +/* update the cookie to newly read cookie from GuC */ + db_cmp.cookie = db_ret.cookie; + db_exc.cookie = db_ret.cookie +1 ; +if (db_exc.cookie ==0 ) + db_exc.cookie =1 ; + } + +kunmap_atomic (base); +return ret; +} + +static void guc_disable_doorbell (struct intel_guc *guc, +struct i915_guc_client *client) +{ +struct drm_i915_private *dev_priv =guc_to_i915 (guc); +struct guc_doorbell_info *doorbell; +void *base; +int drbreg =GEN8_DRBREGL (client->doorbell_id); +int value; + + base =kmap_atomic (i915_gem_object_get_page (client->client_obj,0 )); + doorbell = base + client->doorbell_offset; + + doorbell->db_status =0 ; + +kunmap_atomic (base); + +I915_WRITE (drbreg,I915_READ (drbreg) & ~GEN8_DRB_VALID ); + + value =I915_READ (drbreg); +WARN_ON ((value &GEN8_DRB_VALID ) !=0 ); + +I915_WRITE (GEN8_DRBREGU (client->doorbell_id),0 ); +I915_WRITE (drbreg,0 ); + +/* XXX: wait for any interrupts */ +/* XXX: wait for workqueue to drain */ +} + +/* +* Select, assign and relase doorbell cachelines +* +* These functions track which doorbell cachelines are in use. +* The data they manipulate is protected by the host2guc lock. +*/ + +static uint32_t select_doorbell_cacheline (struct intel_guc *guc) +{ +const uint32_t cacheline_size =cache_line_size (); +uint32_t offset; + +spin_lock (&guc->host2guc_lock); + +/* Doorbell uses a single cache line within a page */ + offset =offset_in_page (guc->db_cacheline); + +/* Moving to next cache line to reduce contention */ + guc->db_cacheline += cacheline_size; + +spin_unlock (&guc->host2guc_lock); + +DRM_DEBUG_DRIVER ("selected doorbell cacheline 0x%x, next 0x%x, linesize %u\n" , + offset, guc->db_cacheline, cacheline_size); + +return offset; +} + +static uint16_t assign_doorbell (struct intel_guc *guc,uint32_t priority) +{ +/* +* The bitmap is split into two halves; the first half is used for +* normal priority contexts, the second half for high-priority ones. +* Note that logically higher priorities are numerically less than +* normal ones, so the test below means "is it high-priority?" +*/ +const bool hi_pri = (priority <=GUC_CTX_PRIORITY_HIGH ); +const uint16_t half =GUC_MAX_DOORBELLS /2 ; +const uint16_t start = hi_pri ? half :0 ; +const uint16_t end = start + half; +uint16_t id; + +spin_lock (&guc->host2guc_lock); + id =find_next_zero_bit (guc->doorbell_bitmap, end, start); +if (id == end) + id =GUC_INVALID_DOORBELL_ID ; +else +bitmap_set (guc->doorbell_bitmap, id,1 ); +spin_unlock (&guc->host2guc_lock); + +DRM_DEBUG_DRIVER ("assigned %s priority doorbell id 0x%x\n" , + hi_pri ?"high" :"normal" , id); + +return id; +} + +static void release_doorbell (struct intel_guc *guc,uint16_t id) +{ +spin_lock (&guc->host2guc_lock); +bitmap_clear (guc->doorbell_bitmap, id,1 ); +spin_unlock (&guc->host2guc_lock); +} + +/* +* Initialise the process descriptor shared with the GuC firmware. +*/ +static void guc_init_proc_desc (struct intel_guc *guc, +struct i915_guc_client *client) +{ +struct guc_process_desc *desc; +void *base; + + base =kmap_atomic (i915_gem_object_get_page (client->client_obj,0 )); + desc = base + client->proc_desc_offset; + +memset (desc,0 ,sizeof (*desc)); + +/* +* XXX: pDoorbell and WQVBaseAddress are pointers in process address +* space for ring3 clients (set them as in mmap_ioctl) or kernel +* space for kernel clients (map on demand instead? May make debug +* easier to have it mapped). +*/ + desc->wq_base_addr =0 ; + desc->db_base_addr =0 ; + + desc->context_id = client->ctx_index; + desc->wq_size_bytes = client->wq_size; + desc->wq_status =WQ_STATUS_ACTIVE ; + desc->priority = client->priority; + +kunmap_atomic (base); +} + +/* +* Initialise/clear the context descriptor shared with the GuC firmware. +* +* This descriptor tells the GuC where (in GGTT space) to find the important +* data structures relating to this client (doorbell, process descriptor, +* write queue, etc). +*/ + +static void guc_init_ctx_desc (struct intel_guc *guc, +struct i915_guc_client *client) +{ +struct guc_context_desc desc; +struct sg_table *sg; + +memset (&desc,0 ,sizeof (desc)); + + desc.attribute =GUC_CTX_DESC_ATTR_ACTIVE |GUC_CTX_DESC_ATTR_KERNEL ; + desc.context_id = client->ctx_index; + desc.priority = client->priority; + desc.engines_used = (1 <<RCS ) | (1 <<VCS ) | (1 <<BCS ) | + (1 <<VECS ) | (1 <<VCS2 );/* all engines */ + desc.db_id = client->doorbell_id; + +/* +* The CPU address is only needed at certain points, so kmap_atomic on +* demand instead of storing it in the ctx descriptor. +* XXX: May make debug easier to have it mapped +*/ + desc.db_trigger_cpu =0 ; + desc.db_trigger_uk = client->doorbell_offset + +i915_gem_obj_ggtt_offset (client->client_obj); + desc.db_trigger_phy = client->doorbell_offset + +sg_dma_address (client->client_obj->pages->sgl); + + desc.process_desc = client->proc_desc_offset + +i915_gem_obj_ggtt_offset (client->client_obj); + + desc.wq_addr = client->wq_offset + +i915_gem_obj_ggtt_offset (client->client_obj); + + desc.wq_size = client->wq_size; + +/* +* XXX: Take LRCs from an existing intel_context if this is not an +* IsKMDCreatedContext client +*/ + desc.desc_private = (uintptr_t )client; + +/* Pool context is pinned already */ + sg = guc->ctx_pool_obj->pages; +sg_pcopy_from_buffer (sg->sgl, sg->nents, &desc,sizeof (desc), +sizeof (desc) * client->ctx_index); +} + +static void guc_fini_ctx_desc (struct intel_guc *guc, +struct i915_guc_client *client) +{ +struct guc_context_desc desc; +struct sg_table *sg; + +memset (&desc,0 ,sizeof (desc)); + + sg = guc->ctx_pool_obj->pages; +sg_pcopy_from_buffer (sg->sgl, sg->nents, &desc,sizeof (desc), +sizeof (desc) * client->ctx_index); +} + +/* Get valid workqueue item and return it back to offset */ +static int guc_get_workqueue_space (struct i915_guc_client *gc,u32 *offset) +{ +struct guc_process_desc *desc; +void *base; +u32 size =sizeof (struct guc_wq_item ); +int ret =0 , timeout_counter =200 ; + + base =kmap_atomic (i915_gem_object_get_page (gc->client_obj,0 )); + desc = base + gc->proc_desc_offset; + +while (timeout_counter-- >0 ) { + ret =wait_for_atomic (CIRC_SPACE (gc->wq_tail, desc->head, + gc->wq_size) >= size,1 ); + +if (!ret) { + *offset = gc->wq_tail; + +/* advance the tail for next workqueue item */ + gc->wq_tail += size; + gc->wq_tail &= gc->wq_size -1 ; + +/* this will break the loop */ + timeout_counter =0 ; + } + }; + +kunmap_atomic (base); + +return ret; +} + +static int guc_add_workqueue_item (struct i915_guc_client *gc, +struct drm_i915_gem_request *rq) +{ +enum intel_ring_id ring_id = rq->ring->id; +struct guc_wq_item *wqi; +void *base; +u32 tail, wq_len, wq_off =0 ; +int ret; + + ret =guc_get_workqueue_space (gc, &wq_off); +if (ret) +return ret; + +/* For now workqueue item is 4 DWs; workqueue buffer is 2 pages. So we +* should not have the case where structure wqi is across page, neither +* wrapped to the beginning. This simplifies the implementation below. +* +* XXX: if not the case, we need save data to a temp wqi and copy it to +* workqueue buffer dw by dw. +*/ +WARN_ON (sizeof (struct guc_wq_item ) !=16 ); +WARN_ON (wq_off &3 ); + +/* wq starts from the page after doorbell / process_desc */ + base =kmap_atomic (i915_gem_object_get_page (gc->client_obj, + (wq_off +GUC_DB_SIZE ) >>PAGE_SHIFT )); + wq_off &=PAGE_SIZE -1 ; + wqi = (struct guc_wq_item *)((char *)base + wq_off); + +/* len does not include the header */ + wq_len =sizeof (struct guc_wq_item ) /sizeof (u32) -1 ; + wqi->header =WQ_TYPE_INORDER | + (wq_len <<WQ_LEN_SHIFT ) | + (ring_id <<WQ_TARGET_SHIFT ) | +WQ_NO_WCFLUSH_WAIT ; + +/* The GuC wants only the low-order word of the context descriptor */ + wqi->context_desc = (u32 )intel_lr_context_descriptor (rq->ctx, rq->ring); + +/* The GuC firmware wants the tail index in QWords, not bytes */ + tail = rq->ringbuf->tail >>3 ; + wqi->ring_tail = tail <<WQ_RING_TAIL_SHIFT ; + wqi->fence_id =0 ;/*XXX: what fence to be here */ + +kunmap_atomic (base); + +return 0 ; +} + +/** +* i915_guc_submit() - Submit commands through GuC +* @client: the guc client where commands will go through +* @ctx: LRC where commands come from +* @ring: HW engine that will excute the commands +* +* Return: 0 if succeed +*/ +int i915_guc_submit (struct i915_guc_client *client, +struct drm_i915_gem_request *rq) +{ +struct intel_guc *guc = client->guc; +enum intel_ring_id ring_id = rq->ring->id; +unsigned long flags; +int q_ret, b_ret; + +spin_lock_irqsave (&client->wq_lock, flags); + + q_ret =guc_add_workqueue_item (client, rq); +if (q_ret ==0 ) + b_ret =guc_ring_doorbell (client); + + client->submissions[ring_id] +=1 ; +if (q_ret) { + client->q_fail +=1 ; + client->retcode = q_ret; + }else if (b_ret) { + client->b_fail +=1 ; + client->retcode = q_ret = b_ret; + }else { + client->retcode =0 ; + } +spin_unlock_irqrestore (&client->wq_lock, flags); + +spin_lock (&guc->host2guc_lock); + guc->submissions[ring_id] +=1 ; + guc->last_seqno[ring_id] = rq->seqno; +spin_unlock (&guc->host2guc_lock); + +return q_ret; +} + +/* +* Everything below here is concerned with setup & teardown, and is +* therefore not part of the somewhat time-critical batch-submission +* path of i915_guc_submit() above. +*/ + +/** * gem_allocate_guc_obj() - Allocate gem object for GuC usage * @dev: drm device * @size: size of object
@@ -79,6 +602,121 @@ static void gem_release_guc_obj(struct drm_i915_gem_object *obj)drm_gem_object_unreference (&obj->base); } +static void guc_client_free (struct drm_device *dev, +struct i915_guc_client *client) +{ +struct drm_i915_private *dev_priv = dev->dev_private; +struct intel_guc *guc = &dev_priv->guc; + +if (!client) +return ; + +if (client->doorbell_id !=GUC_INVALID_DOORBELL_ID ) { +/* +* First disable the doorbell, then tell the GuC we've +* finished with it, finally deallocate it in our bitmap +*/ +guc_disable_doorbell (guc, client); +host2guc_release_doorbell (guc, client); +release_doorbell (guc, client->doorbell_id); + } + +/* +* XXX: wait for any outstanding submissions before freeing memory. +* Be sure to drop any locks +*/ + +gem_release_guc_obj (client->client_obj); + +if (client->ctx_index !=GUC_INVALID_CTX_ID ) { +guc_fini_ctx_desc (guc, client); +ida_simple_remove (&guc->ctx_ids, client->ctx_index); + } + +kfree (client); +} + +/** +* guc_client_alloc() - Allocate an i915_guc_client +* @dev: drm device +* @priority: four levels priority _CRITICAL, _HIGH, _NORMAL and _LOW +* The kernel client to replace ExecList submission is created with +* NORMAL priority. Priority of a client for scheduler can be HIGH, +* while a preemption context can use CRITICAL. +* +* Return: An i915_guc_client object if success. +*/ +static struct i915_guc_client *guc_client_alloc (struct drm_device *dev, +uint32_t priority) +{ +struct i915_guc_client *client; +struct drm_i915_private *dev_priv = dev->dev_private; +struct intel_guc *guc = &dev_priv->guc; +struct drm_i915_gem_object *obj; + + client =kzalloc (sizeof (*client),GFP_KERNEL ); +if (!client) +return NULL ; + + client->doorbell_id =GUC_INVALID_DOORBELL_ID ; + client->priority = priority; + client->guc = guc; + + client->ctx_index = (uint32_t )ida_simple_get (&guc->ctx_ids,0 , +GUC_MAX_GPU_CONTEXTS ,GFP_KERNEL ); +if (client->ctx_index >=GUC_MAX_GPU_CONTEXTS ) { + client->ctx_index =GUC_INVALID_CTX_ID ; + goto err; + } + +/* The first page is doorbell/proc_desc. Two followed pages are wq. */ + obj =gem_allocate_guc_obj (dev,GUC_DB_SIZE +GUC_WQ_SIZE ); +if (!obj) + goto err; + + client->client_obj = obj; + client->wq_offset =GUC_DB_SIZE ; + client->wq_size =GUC_WQ_SIZE ; +spin_lock_init (&client->wq_lock); + + client->doorbell_offset =select_doorbell_cacheline (guc); + +/* +* Since the doorbell only requires a single cacheline, we can save +* space by putting the application process descriptor in the same +* page. Use the half of the page that doesn't include the doorbell. +*/ +if (client->doorbell_offset >= (GUC_DB_SIZE /2 )) + client->proc_desc_offset =0 ; +else + client->proc_desc_offset = (GUC_DB_SIZE /2 ); + + client->doorbell_id =assign_doorbell (guc, client->priority); +if (client->doorbell_id ==GUC_INVALID_DOORBELL_ID ) +/* XXX: evict a doorbell instead */ + goto err; + +guc_init_proc_desc (guc, client); +guc_init_ctx_desc (guc, client); +guc_init_doorbell (guc, client); + +/* XXX: Any cache flushes needed? General domain mgmt calls? */ + +if (host2guc_allocate_doorbell (guc, client)) + goto err; + +DRM_DEBUG_DRIVER ("new priority %u client %p: ctx_index %u db_id %u\n" , + priority, client, client->ctx_index, client->doorbell_id); + +return client; + +err: +DRM_ERROR ("FAILED to create priority %u GuC client!\n" , priority); + +guc_client_free (dev, client); +return NULL ; +} +static void guc_create_log (struct intel_guc *guc) {struct drm_i915_private *dev_priv =guc_to_i915 (guc);
@@ -142,6 +780,8 @@ int i915_guc_submission_init(struct drm_device *dev)if (!guc->ctx_pool_obj)return -ENOMEM ; +spin_lock_init (&dev_priv->guc.host2guc_lock); +ida_init (&guc->ctx_ids);guc_create_log (guc);
@@ -149,6 +789,32 @@ int i915_guc_submission_init(struct drm_device *dev)return 0 ; } +int i915_guc_submission_enable (struct drm_device *dev) +{ +struct drm_i915_private *dev_priv = dev->dev_private; +struct intel_guc *guc = &dev_priv->guc; +struct i915_guc_client *client; + +/* client for execbuf submission */ + client =guc_client_alloc (dev,GUC_CTX_PRIORITY_KMD_NORMAL ); +if (!client) { +DRM_ERROR ("Failed to create execbuf guc_client\n" ); +return -ENOMEM ; + } + + guc->execbuf_client = client; +return 0 ; +} + +void i915_guc_submission_disable (struct drm_device *dev) +{ +struct drm_i915_private *dev_priv = dev->dev_private; +struct intel_guc *guc = &dev_priv->guc; + +guc_client_free (dev, guc->execbuf_client); + guc->execbuf_client =NULL ; +} +void i915_guc_submission_fini (struct drm_device *dev) {struct drm_i915_private *dev_priv = dev->dev_private;
drivers/gpu/drm/i915/intel_guc.h +46 -0
64 lines not on this page · raw message
drivers/gpu/drm/i915/intel_guc_fwif.h +3 -3
@@ -35,10 +35,10 @@#define GFXCORE_FAMILY_GEN9 12#define GFXCORE_FAMILY_UNKNOWN 0x7fffffff -#define GUC_CTX_PRIORITY_CRITICAL 0 +#define GUC_CTX_PRIORITY_KMD_HIGH 0#define GUC_CTX_PRIORITY_HIGH 1 -#define GUC_CTX_PRIORITY_NORMAL 2 -#define GUC_CTX_PRIORITY_LOW 3 +#define GUC_CTX_PRIORITY_KMD_NORMAL 2 +#define GUC_CTX_PRIORITY_NORMAL 3#define GUC_MAX_GPU_CONTEXTS 1024#define GUC_INVALID_CTX_ID (GUC_MAX_GPU_CONTEXTS + 1)
drivers/gpu/drm/i915/intel_guc_loader.c +10 -0
@@ -342,6 +342,8 @@ int intel_guc_ucode_load(struct drm_device *dev)intel_guc_fw_status_repr (guc_fw->guc_fw_fetch_status), intel_guc_fw_status_repr(guc_fw->guc_fw_load_status)); +i915_guc_submission_disable (dev); +if (guc_fw->guc_fw_fetch_status ==GUC_FIRMWARE_NONE )return 0 ;
@@ -389,12 +391,20 @@ int intel_guc_ucode_load(struct drm_device *dev)intel_guc_fw_status_repr (guc_fw->guc_fw_fetch_status), intel_guc_fw_status_repr(guc_fw->guc_fw_load_status)); +if (i915.enable_guc_submission) { + err =i915_guc_submission_enable (dev); +if (err) + goto fail; + } +return 0 ; fail:if (guc_fw->guc_fw_load_status ==GUC_FIRMWARE_PENDING ) guc_fw->guc_fw_load_status =GUC_FIRMWARE_FAIL ; +i915_guc_submission_disable (dev); +return err; }
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 7/9 drm/i915: Interrupt routing for GuC submission
In reply to Dave GordonTurn on interrupt steering to route necessary interrupts to GuC.
v6:
Rebased
Issue: VIZ-4884
--- drivers/gpu/drm/i915/i915_reg.h | 11 +++++-- drivers/gpu/drm/i915/intel_guc_loader.c | 51 +++++++++++++++++++++++++++++++++ 2 files changed, 60 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/i915_reg.h +9 -2
@@ -1674,6 +1674,7 @@ enum skl_disp_power_wells {#define GFX_MODE_GEN7 0x0229c#define RING_MODE_GEN7 (ring) ((ring)->mmio_base+0x29c)#define GFX_RUN_LIST_ENABLE (1<<15) +#define GFX_INTERRUPT_STEERING (1<<14)#define GFX_TLB_INVALIDATE_EXPLICIT (1<<13)#define GFX_SURFACE_FAULT_ENABLE (1<<12)#define GFX_REPLAY_MODE (1<<11)
@@ -1681,6 +1682,11 @@ enum skl_disp_power_wells {#define GFX_PPGTT_ENABLE (1<<9)#define GEN8_GFX_PPGTT_48B (1<<7) +#define GFX_FORWARD_VBLANK_MASK (3<<5) +#define GFX_FORWARD_VBLANK_NEVER (0<<5) +#define GFX_FORWARD_VBLANK_ALWAYS (1<<5) +#define GFX_FORWARD_VBLANK_COND (2<<5) +#define VLV_DISPLAY_BASE 0x180000#define VLV_MIPI_BASE VLV_DISPLAY_BASE
@@ -5694,11 +5700,12 @@ enum skl_disp_power_wells {#define GEN8_GT_IIR (which) (0x44308 + (0x10 * (which)))#define GEN8_GT_IER (which) (0x4430c + (0x10 * (which))) -#define GEN8_BCS_IRQ_SHIFT 16#define GEN8_RCS_IRQ_SHIFT 0 -#define GEN8_VCS2_IRQ_SHIFT 16 +#define GEN8_BCS_IRQ_SHIFT 16#define GEN8_VCS1_IRQ_SHIFT 0 +#define GEN8_VCS2_IRQ_SHIFT 16#define GEN8_VECS_IRQ_SHIFT 0 +#define GEN8_WD_IRQ_SHIFT 16#define GEN8_DE_PIPE_ISR (pipe) (0x44400 + (0x10 * (pipe)))#define GEN8_DE_PIPE_IMR (pipe) (0x44404 + (0x10 * (pipe)))
drivers/gpu/drm/i915/intel_guc_loader.c +51 -0
81 lines not on this page · raw message
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 8/9 drm/i915: Integrate GuC-based command submission
In reply to Dave GordonFrom: Alex Dai <[email protected]>
GuC-based submission is mostly the same as execlist mode, up to intel_logical_ring_advance_and_submit(), where the context being dispatched would be added to the execlist queue; at this point we submit the context to the GuC backend instead.
There are, however, a few other changes also required, notably:
1. Contexts must be pinned at GGTT addresses accessible by the GuC i.e. NOT in the range [0..WOPCM_SIZE), so we have to add the PIN_OFFSET_BIAS flag to the relevant GGTT-pinning calls.
2. The GuC's TLB must be invalidated after a context is pinned at a new GGTT address.
3. GuC firmware uses the one page before Ring Context as shared data. Therefore, whenever driver wants to get base address of LRC, we will offset one page for it. LRC_PPHWSP_PN is defined as the page number of LRCA.
4. In the work queue used to pass requests to the GuC, the GuC firmware requires the ring-tail-offset to be represented as an 11-bit value, expressed in QWords. Therefore, the ringbuffer size must be reduced to the representable range (4 pages).
v2:
Defer adding #defines until needed [Chris Wilson] Rationalise type declarations [Chris Wilson]
v4:
Squashed kerneldoc patch into here [Daniel Vetter]
v5:
Update request->tail in code common to both GuC and execlist modes. Add a private version of lr_context_update(), as sharing the
execlist version leads to race conditions when the CPU and the GuC both update TAIL in the context image.
Conversion of error-captured HWS page to string must account
for offset from start of object to actual HWS (LRC_PPHWSP_PN).
Issue: VIZ-4884
--- Documentation/DocBook/drm.tmpl | 14 ++++++ drivers/gpu/drm/i915/i915_debugfs.c | 2 +- drivers/gpu/drm/i915/i915_gpu_error.c | 14 +++--- drivers/gpu/drm/i915/i915_guc_submission.c | 79 ++++++++++++++++++++++++++++-- drivers/gpu/drm/i915/intel_guc.h | 1 + drivers/gpu/drm/i915/intel_lrc.c | 55 ++++++++++++++------- drivers/gpu/drm/i915/intel_lrc.h | 6 +++ 7 files changed, 142 insertions(+), 29 deletions(-)
Documentation/DocBook/drm.tmpl +14 -0
@@ -4152,6 +4152,20 @@ int num_ioctls;</synopsis> </sect2> </sect1> <sect1> + <title>GuC-based Command Submission</title> + <sect2> + <title>GuC</title> +!Pdrivers/gpu/drm/i915/intel_guc_loader.c GuC-specific firmware loader +!Idrivers/gpu/drm/i915/intel_guc_loader.c + </sect2> + <sect2> + <title>GuC Client</title> +!Pdrivers/gpu/drm/i915/intel_guc_submission.c GuC-based command submissison +!Idrivers/gpu/drm/i915/intel_guc_submission.c + </sect2> + </sect1> + + <sect1> <title> Tracing </title> <para> This sections covers all things related to the tracepoints implemented in
drivers/gpu/drm/i915/i915_debugfs.c +1 -1
@@ -1995,7 +1995,7 @@ static void i915_dump_lrc_obj(struct seq_file *m,return ; } - page =i915_gem_object_get_page (ctx_obj,1 ); + page =i915_gem_object_get_page (ctx_obj,LRC_STATE_PN );if (!WARN_ON (page ==NULL )) { reg_state =kmap_atomic (page);
drivers/gpu/drm/i915/i915_gpu_error.c +7 -7
@@ -461,17 +461,17 @@ int i915_error_state_to_str(struct drm_i915_error_state_buf *m, }if ((obj = error->ring[i].hws_page)) { -err_printf (m,"%s --- HW Status = 0x%08x\n" , - dev_priv->ring[i].name, -lower_32_bits (obj->gtt_offset)); +err_printf (m,"%s --- HW Status = 0x%08llx\n" , + dev_priv->ring[i].name, + obj->gtt_offset +LRC_PPHWSP_PN *PAGE_SIZE ); offset =0 ;for (elt =0 ; elt <PAGE_SIZE /16 ; elt +=4 ) {err_printf (m,"[%04x] %08x %08x %08x %08x\n" , offset, - obj->pages[0 ][elt], - obj->pages[0 ][elt+1 ], - obj->pages[0 ][elt+2 ], - obj->pages[0 ][elt+3 ]); + obj->pages[LRC_PPHWSP_PN ][elt], + obj->pages[LRC_PPHWSP_PN ][elt+1 ], + obj->pages[LRC_PPHWSP_PN ][elt+2 ], + obj->pages[LRC_PPHWSP_PN ][elt+3 ]); offset +=16 ; } }
drivers/gpu/drm/i915/i915_guc_submission.c +75 -4
132 lines not on this page · raw message
drivers/gpu/drm/i915/intel_guc.h +1 -0
@@ -29,6 +29,7 @@struct i915_guc_client {struct drm_i915_gem_object *client_obj; +struct intel_context *owner;struct intel_guc *guc;uint32_t priority;uint32_t ctx_index;
drivers/gpu/drm/i915/intel_lrc.c +38 -17
158 lines not on this page · raw message
drivers/gpu/drm/i915/intel_lrc.h +6 -0
@@ -68,6 +68,12 @@ static inline void intel_logical_ring_emit(struct intel_ringbuffer *ringbuf, }/* Logical Ring Contexts */ + +/* One extra page is added before LRC for GuC as shared data */ +#define LRC_GUCSHR_PN (0) +#define LRC_PPHWSP_PN (LRC_GUCSHR_PN + 1) +#define LRC_STATE_PN (LRC_PPHWSP_PN + 1) +void intel_lr_context_free (struct intel_context *ctx);int intel_lr_context_deferred_create (struct intel_context *ctx,struct intel_engine_cs *ring);
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 9/9 drm/i915: Debugfs interface for GuC submission statistics
In reply to Dave GordonThis provides a means of reading status and counts relating to GuC actions and submissions.
v2:
Remove surplus blank line in output [Chris Wilson]
v5:
Added GuC per-engine submission & seqno statistics
v6:
Add per-ring statistics to client, refactor client-dumper.
--- drivers/gpu/drm/i915/i915_debugfs.c | 76 +++++++++++++++++++++++++++++++++++++ 1 file changed, 76 insertions(+)
drivers/gpu/drm/i915/i915_debugfs.c +76 -0
@@ -2412,6 +2412,81 @@ static int i915_guc_load_status_info(struct seq_file *m, void *data)return 0 ; } +static void i915_guc_client_info (struct seq_file *m, +struct drm_i915_private *dev_priv, +struct i915_guc_client *client) +{ +struct intel_engine_cs *ring; +uint64_t tot =0 ; +uint32_t i; + +seq_printf (m,"\tPriority %d, GuC ctx index: %u, PD offset 0x%x\n" , + client->priority, client->ctx_index, client->proc_desc_offset); +seq_printf (m,"\tDoorbell id %d, offset: 0x%x, cookie 0x%x\n" , + client->doorbell_id, client->doorbell_offset, client->cookie); +seq_printf (m,"\tWQ size %d, offset: 0x%x, tail %d\n" , + client->wq_size, client->wq_offset, client->wq_tail); + +seq_printf (m,"\tFailed to queue: %u\n" , client->q_fail); +seq_printf (m,"\tFailed doorbell: %u\n" , client->b_fail); +seq_printf (m,"\tLast submission result: %d\n" , client->retcode); + +for_each_ring (ring, dev_priv, i) { +seq_printf (m,"\tSubmissions: %llu %s\n" , + client->submissions[i], + ring->name); + tot += client->submissions[i]; + } +seq_printf (m,"\tTotal: %llu\n" , tot); +} + +static int i915_guc_info (struct seq_file *m,void *data) +{ +struct drm_info_node *node = m->private; +struct drm_device *dev = node->minor->dev; +struct drm_i915_private *dev_priv = dev->dev_private; +struct intel_guc guc; +struct i915_guc_client client = { .client_obj =0 }; +struct intel_engine_cs *ring; +enum intel_ring_id i; +u64 total =0 ; + +if (!HAS_GUC_SCHED (dev_priv->dev)) +return 0 ; + +/* Take a local copy of the GuC data, so we can dump it at leisure */ +spin_lock (&dev_priv->guc.host2guc_lock); + guc = dev_priv->guc; +if (guc.execbuf_client) { +spin_lock (&guc.execbuf_client->wq_lock); + client = *guc.execbuf_client; +spin_unlock (&guc.execbuf_client->wq_lock); + } +spin_unlock (&dev_priv->guc.host2guc_lock); + +seq_printf (m,"GuC total action count: %llu\n" , guc.action_count); +seq_printf (m,"GuC action failure count: %u\n" , guc.action_fail); +seq_printf (m,"GuC last action command: 0x%x\n" , guc.action_cmd); +seq_printf (m,"GuC last action status: 0x%x\n" , guc.action_status); +seq_printf (m,"GuC last action error code: %d\n" , guc.action_err); + +seq_printf (m,"\nGuC submissions:\n" ); +for_each_ring (ring, dev_priv, i) { +seq_printf (m,"\t%-24s: %10llu, last seqno 0x%08x %9d\n" , + ring->name, guc.submissions[i], + guc.last_seqno[i], guc.last_seqno[i]); + total += guc.submissions[i]; + } +seq_printf (m,"\t%s: %llu\n" ,"Total" , total); + +seq_printf (m,"\nGuC execbuf client @ %p:\n" , guc.execbuf_client); +i915_guc_client_info (m, dev_priv, &client); + +/* Add more as required ... */ + +return 0 ; +} +static int i915_guc_log_dump (struct seq_file *m,void *data) {struct drm_info_node *node = m->private;
@@ -5099,6 +5174,7 @@ static const struct drm_info_list i915_debugfs_list[] = { {"i915_gem_hws_bsd", i915_hws_info, 0, (void *)VCS}, {"i915_gem_hws_vebox", i915_hws_info, 0, (void *)VECS}, {"i915_gem_batch_pool", i915_gem_batch_pool_info, 0}, + {"i915_guc_info", i915_guc_info, 0}, {"i915_guc_load_status", i915_guc_load_status_info, 0}, {"i915_guc_log_dump", i915_guc_log_dump, 0}, {"i915_frequency_info", i915_frequency_info, 0},
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 81 lines · Dave Gordon
This patch series enables command submission via the GuC. In this mode, instead of the host CPU driving the execlist port directly, it hands over work items to the GuC, using a doorbell mechanism to tell the GuC that new items have been added to its work queue. The GuC then dispatches contexts to the various GPU engines, and manages the resulting context- switch interrupts. Completion of a batch is however still signalled to the CPU; the GuC is not involved in handling user interrupts.
There are two subsequences within the patch series:
drm/i915: GuC-specific firmware loader drm/i915: Debugfs interface to read GuC load status
These two patches provide the GuC loader and a debugfs interface to verify the resulting state. At this point in the sequence we can load and activate the GuC firmware, but not submit any batches through it. (This is nonetheless a potentially useful state, as the GuC could do other useful work even when not handling batch submissions).
drm/i915: Expose one LRC function for GuC submission mode drm/i915: Prepare for GuC-based command submission drm/i915: Enable GuC firmware log
drm/i915: Implementation of GuC submission client drm/i915: Interrupt routing for GuC submission drm/i915: Integrate GuC-based command submission drm/i915: Debugfs interface for GuC submission statisticsIn this second section, we implement the GuC submission mechanism, and link it into the (execlist-based) submission path. At this stage, it is not yet enabled by default; it is activated only if the kernel command line explicitly switches it on.
The GuC firmware itself is not included in this patchset; it is or will be available for download from https://01.org/linuxgraphics/downloads/
This driver works with and requires GuC firmware revision 3.x. It will not work with any firmware version 1.x, as the GuC protocol in those revisions was incompatible and is no longer supported.On platforms where there is no GuC, or where GuC submission is not specifically enabled, batch submission will continue to use the execlist (or ringbuffer) mechanisms. On the other hand, if GuC submission is requested but the GuC firmware cannot be found or is invalid, the GPU will be unusable.
It is expected that a subsequent patch will enable GuC submission by default once the signed firmware is published on 01.org.
Ben Widawsky (0):
Vinit Azad (0):
Michael H. Nguyen (0):
created the original versions on which some of these patches are based.Alex Dai (5):
drm/i915: GuC-specific firmware loader drm/i915: Debugfs interface to read GuC load status drm/i915: Prepare for GuC-based command submission drm/i915: Enable GuC firmware log drm/i915: Integrate GuC-based command submissionDave Gordon (4):
drm/i915: Expose one LRC function for GuC submission mode drm/i915: Implementation of GuC submission client drm/i915: Interrupt routing for GuC submission drm/i915: Debugfs interface for GuC submission statisticsDocumentation/DocBook/drm.tmpl | 14 + drivers/gpu/drm/i915/Makefile | 4 + drivers/gpu/drm/i915/i915_debugfs.c | 146 ++++- drivers/gpu/drm/i915/i915_dma.c | 9 + drivers/gpu/drm/i915/i915_drv.h | 11 + drivers/gpu/drm/i915/i915_gem.c | 16 + drivers/gpu/drm/i915/i915_gpu_error.c | 14 +- drivers/gpu/drm/i915/i915_guc_reg.h | 17 +- drivers/gpu/drm/i915/i915_guc_submission.c | 901 +++++++++++++++++++++++++++++ drivers/gpu/drm/i915/i915_reg.h | 15 +- drivers/gpu/drm/i915/intel_guc.h | 122 ++++ drivers/gpu/drm/i915/intel_guc_fwif.h | 9 +- drivers/gpu/drm/i915/intel_guc_loader.c | 611 +++++++++++++++++++ drivers/gpu/drm/i915/intel_lrc.c | 65 ++- drivers/gpu/drm/i915/intel_lrc.h | 8 + 15 files changed, 1918 insertions(+), 44 deletions(-)
Quoted 3 lines
create mode 100644
drivers/gpu/drm/i915/i915_guc_submission.ccreate mode 100644drivers/gpu/drm/i915/intel_guc.hcreate mode 100644drivers/gpu/drm/i915/intel_guc_loader.c
Tom O'Rourke has already R-B'ed the previous [v5] versions of these, and there are no substantive changes to patches 2, 3, 4, 5, 7 and 8, so we can carry that over; also, the change in patch 1 is just an update to a comment noted in Tom's earlier reviews as being out-of-date.
I haven't included patch 10 (enable-by-default) as we've decided to wait until the signed firmware is publicly available on 01.org before making it the default.
So, it's really just patches 6/9 and 9/9 that need a re-review from Tom.
Thanks,
.Dave.
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
O'Rourke, Tom
Reviewed-byQuoted 91 lines · David S
Quoted 81 lines · Dave Gordon
This patch series enables command submission via the GuC. In this mode, instead of the host CPU driving the execlist port directly, it hands over work items to the GuC, using a doorbell mechanism to tell the GuC that new items have been added to its work queue. The GuC then dispatches contexts to the various GPU engines, and manages the resulting context- switch interrupts. Completion of a batch is however still signalled to the CPU; the GuC is not involved in handling user interrupts.
There are two subsequences within the patch series:
drm/i915: GuC-specific firmware loader drm/i915: Debugfs interface to read GuC load status
These two patches provide the GuC loader and a debugfs interface to verify the resulting state. At this point in the sequence we can load and activate the GuC firmware, but not submit any batches through it. (This is nonetheless a potentially useful state, as the GuC could do other useful work even when not handling batch submissions).
drm/i915: Expose one LRC function for GuC submission mode drm/i915: Prepare for GuC-based command submission drm/i915: Enable GuC firmware log
drm/i915: Implementation of GuC submission client drm/i915: Interrupt routing for GuC submission drm/i915: Integrate GuC-based command submission drm/i915: Debugfs interface for GuC submission statisticsIn this second section, we implement the GuC submission mechanism, and link it into the (execlist-based) submission path. At this stage, it is not yet enabled by default; it is activated only if the kernel command line explicitly switches it on.
The GuC firmware itself is not included in this patchset; it is or will be available for download from https://01.org/linuxgraphics/downloads/
This driver works with and requires GuC firmware revision 3.x. It will not work with any firmware version 1.x, as the GuC protocol in those revisions was incompatible and is no longer supported.On platforms where there is no GuC, or where GuC submission is not specifically enabled, batch submission will continue to use the execlist (or ringbuffer) mechanisms. On the other hand, if GuC submission is requested but the GuC firmware cannot be found or is invalid, the GPU will be unusable.
It is expected that a subsequent patch will enable GuC submission by default once the signed firmware is published on 01.org.
Ben Widawsky (0):
Vinit Azad (0):
Michael H. Nguyen (0):
created the original versions on which some of these patches are based.Alex Dai (5):
drm/i915: GuC-specific firmware loader drm/i915: Debugfs interface to read GuC load status drm/i915: Prepare for GuC-based command submission drm/i915: Enable GuC firmware log drm/i915: Integrate GuC-based command submissionDave Gordon (4):
drm/i915: Expose one LRC function for GuC submission mode drm/i915: Implementation of GuC submission client drm/i915: Interrupt routing for GuC submission drm/i915: Debugfs interface for GuC submission statisticsDocumentation/DocBook/drm.tmpl | 14 + drivers/gpu/drm/i915/Makefile | 4 + drivers/gpu/drm/i915/i915_debugfs.c | 146 ++++- drivers/gpu/drm/i915/i915_dma.c | 9 + drivers/gpu/drm/i915/i915_drv.h | 11 + drivers/gpu/drm/i915/i915_gem.c | 16 + drivers/gpu/drm/i915/i915_gpu_error.c | 14 +- drivers/gpu/drm/i915/i915_guc_reg.h | 17 +- drivers/gpu/drm/i915/i915_guc_submission.c | 901 +++++++++++++++++++++++++++++ drivers/gpu/drm/i915/i915_reg.h | 15 +- drivers/gpu/drm/i915/intel_guc.h | 122 ++++ drivers/gpu/drm/i915/intel_guc_fwif.h | 9 +- drivers/gpu/drm/i915/intel_guc_loader.c | 611 +++++++++++++++++++ drivers/gpu/drm/i915/intel_lrc.c | 65 ++- drivers/gpu/drm/i915/intel_lrc.h | 8 + 15 files changed, 1918 insertions(+), 44 deletions(-)Quoted 3 lines
create mode 100644
drivers/gpu/drm/i915/i915_guc_submission.ccreate mode 100644drivers/gpu/drm/i915/intel_guc.hcreate mode 100644drivers/gpu/drm/i915/intel_guc_loader.cTom O'Rourke has already R-B'ed the previous [v5] versions of these, and there are no substantive changes to patches 2, 3, 4, 5, 7 and 8, so we can carry that over; also, the change in patch 1 is just an update to a comment noted in Tom's earlier reviews as being out-of-date.
Quoted 8 lines
I haven't included patch 10 (enable-by-default) as we've decided to wait until the signed firmware is publicly available on 01.org before making it the default.
So, it's really just patches 6/9 and 9/9 that need a re-review from Tom.
Thanks,
.Dave.
[TOR:] These patches still look good. Good catch in patch 6 with the offset.
For all 9 patches:
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 98 lines · Tom
Quoted 97 lines · David S
Quoted 81 lines · Dave Gordon
This patch series enables command submission via the GuC. In this mode, instead of the host CPU driving the execlist port directly, it hands over work items to the GuC, using a doorbell mechanism to tell the GuC that new items have been added to its work queue. The GuC then dispatches contexts to the various GPU engines, and manages the resulting context- switch interrupts. Completion of a batch is however still signalled to the CPU; the GuC is not involved in handling user interrupts.
There are two subsequences within the patch series:
drm/i915: GuC-specific firmware loader drm/i915: Debugfs interface to read GuC load status
These two patches provide the GuC loader and a debugfs interface to verify the resulting state. At this point in the sequence we can load and activate the GuC firmware, but not submit any batches through it. (This is nonetheless a potentially useful state, as the GuC could do other useful work even when not handling batch submissions).
drm/i915: Expose one LRC function for GuC submission mode drm/i915: Prepare for GuC-based command submission drm/i915: Enable GuC firmware log
drm/i915: Implementation of GuC submission client drm/i915: Interrupt routing for GuC submission drm/i915: Integrate GuC-based command submission drm/i915: Debugfs interface for GuC submission statisticsIn this second section, we implement the GuC submission mechanism, and link it into the (execlist-based) submission path. At this stage, it is not yet enabled by default; it is activated only if the kernel command line explicitly switches it on.
The GuC firmware itself is not included in this patchset; it is or will be available for download from https://01.org/linuxgraphics/downloads/
This driver works with and requires GuC firmware revision 3.x. It will not work with any firmware version 1.x, as the GuC protocol in those revisions was incompatible and is no longer supported.On platforms where there is no GuC, or where GuC submission is not specifically enabled, batch submission will continue to use the execlist (or ringbuffer) mechanisms. On the other hand, if GuC submission is requested but the GuC firmware cannot be found or is invalid, the GPU will be unusable.
It is expected that a subsequent patch will enable GuC submission by default once the signed firmware is published on 01.org.
Ben Widawsky (0):
Vinit Azad (0):
Michael H. Nguyen (0):
created the original versions on which some of these patches are based.Alex Dai (5):
drm/i915: GuC-specific firmware loader drm/i915: Debugfs interface to read GuC load status drm/i915: Prepare for GuC-based command submission drm/i915: Enable GuC firmware log drm/i915: Integrate GuC-based command submissionDave Gordon (4):
drm/i915: Expose one LRC function for GuC submission mode drm/i915: Implementation of GuC submission client drm/i915: Interrupt routing for GuC submission drm/i915: Debugfs interface for GuC submission statisticsDocumentation/DocBook/drm.tmpl | 14 + drivers/gpu/drm/i915/Makefile | 4 + drivers/gpu/drm/i915/i915_debugfs.c | 146 ++++- drivers/gpu/drm/i915/i915_dma.c | 9 + drivers/gpu/drm/i915/i915_drv.h | 11 + drivers/gpu/drm/i915/i915_gem.c | 16 + drivers/gpu/drm/i915/i915_gpu_error.c | 14 +- drivers/gpu/drm/i915/i915_guc_reg.h | 17 +- drivers/gpu/drm/i915/i915_guc_submission.c | 901 +++++++++++++++++++++++++++++ drivers/gpu/drm/i915/i915_reg.h | 15 +- drivers/gpu/drm/i915/intel_guc.h | 122 ++++ drivers/gpu/drm/i915/intel_guc_fwif.h | 9 +- drivers/gpu/drm/i915/intel_guc_loader.c | 611 +++++++++++++++++++ drivers/gpu/drm/i915/intel_lrc.c | 65 ++- drivers/gpu/drm/i915/intel_lrc.h | 8 + 15 files changed, 1918 insertions(+), 44 deletions(-)Quoted 3 lines
create mode 100644
drivers/gpu/drm/i915/i915_guc_submission.ccreate mode 100644drivers/gpu/drm/i915/intel_guc.hcreate mode 100644drivers/gpu/drm/i915/intel_guc_loader.cTom O'Rourke has already R-B'ed the previous [v5] versions of these, and there are no substantive changes to patches 2, 3, 4, 5, 7 and 8, so we can carry that over; also, the change in patch 1 is just an update to a comment noted in Tom's earlier reviews as being out-of-date.
I haven't included patch 10 (enable-by-default) as we've decided to wait until the signed firmware is publicly available on 01.org before making it the default.
So, it's really just patches 6/9 and 9/9 that need a re-review from Tom.
Quoted 7 lines
Quoted 2 lines
Thanks,
.Dave.[TOR:] These patches still look good. Good catch in patch 6 with the offset.
For all 9 patches:
Reviewed-by Tom O'Rourke <Tom.O'[email protected]>
All merged to dinq, thanks.
-Daniel
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx