hw/misc: Add support for ADC controller in Xilinx Zynq 7000
PATCH v2 1/1 hw/misc: Add support for ADC controller in Xilinx Zynq 7000
Add support for the Xilinx XADC core used in Zynq 7000.
References:
- Zynq-7000 All Programmable SoC Technical Reference Manual
- 7 Series FPGAs and Zynq-7000 All Programmable SoC XADC Dual 12-Bit 1 MSPS Analog-to-Digital Converter
Tested with Linux using qemu machine xilinx-zynq-a9 with devicetree files zynq-zc702.dtb and zynq-zc706.dtb, and kernel configuration multi_v7_defconfig.
---
v2: Use extract32()
Merge zynq_xadc_reset() and _zynq_xadc_reset() into one function Use "xlnx,zynq_xadc"
Move device model to include/hw/misc/zynq_xadc.h
irq -> qemu_irq
xadc_dfifo_depth -> xadc_dfifo_entries
Dropped unnecessary comments
Merged zynq_xadc_realize() into zynq_xadc_init()
hw/arm/xilinx_zynq.c | 6 + hw/misc/Makefile.objs | 1 + hw/misc/zynq_xadc.c | 270 ++++++++++++++++++++++++++++++++++++++++++++ include/hw/misc/zynq_xadc.h | 49 ++++++++ 4 files changed, 326 insertions(+) create mode 100644 hw/misc/zynq_xadc.c create mode 100644 include/hw/misc/zynq_xadc.h
hw/arm/xilinx_zynq.c +6 -0
@@ -24,6 +24,7 @@#include "hw/block/flash.h" #include "sysemu/block-backend.h" #include "hw/loader.h" +#include "hw/misc/zynq_xadc.h" #include "hw/ssi.h" #include "qemu/error-report.h"
@@ -225,6 +226,11 @@ static void zynq_init(MachineState *machine)sysbus_mmio_map (SYS_BUS_DEVICE (dev),0 ,0xE0101000 );sysbus_connect_irq (SYS_BUS_DEVICE (dev),0 , pic[79 -IRQ_OFFSET ]); + dev =qdev_create (NULL ,TYPE_ZYNQ_XADC ); +qdev_init_nofail (dev); +sysbus_mmio_map (SYS_BUS_DEVICE (dev),0 ,0xF8007100 ); +sysbus_connect_irq (SYS_BUS_DEVICE (dev),0 , pic[39 -IRQ_OFFSET ]); + dev =qdev_create (NULL ,"pl330" );qdev_prop_set_uint8 (dev,"num_chnls" ,8 );qdev_prop_set_uint8 (dev,"num_periph_req" ,4 );
hw/misc/Makefile.objs +1 -0
@@ -36,6 +36,7 @@ obj-$(CONFIG_OMAP) += omap_sdrc.o obj-$(CONFIG_OMAP) += omap_tap.o obj-$(CONFIG_SLAVIO) += slavio_misc.o obj-$(CONFIG_ZYNQ) += zynq_slcr.o +obj-$(CONFIG_ZYNQ) += zynq_xadc.o obj-$(CONFIG_STM32F2XX_SYSCFG) += stm32f2xx_syscfg.o obj-$(CONFIG_PVPANIC) += pvpanic.o
hw/misc/zynq_xadc.c new file +270 -0
270 lines not on this page · raw message
include/hw/misc/zynq_xadc.h new file +49 -0
49 lines not on this page · raw message
Signature · 1 line
2.1.4
Quoted 84 lines · Guenter Roeck
Add support for the Xilinx XADC core used in Zynq 7000.
References:
- Zynq-7000 All Programmable SoC Technical Reference Manual
- 7 Series FPGAs and Zynq-7000 All Programmable SoC XADC Dual 12-Bit 1 MSPS Analog-to-Digital ConverterTested with Linux using qemu machine xilinx-zynq-a9 with devicetree files zynq-zc702.dtb and zynq-zc706.dtb, and kernel configuration
multi_v7_defconfig.Signed-off-by Guenter Roeck <[email protected]>---
v2: Useextract32()
Mergezynq_xadc_reset()and_zynq_xadc_reset()into one function Use "xlnx,zynq_xadc"
Move device model toinclude/hw/misc/zynq_xadc.h
irq ->qemu_irq
xadc_dfifo_depth->xadc_dfifo_entries
Dropped unnecessary comments
Mergedzynq_xadc_realize()intozynq_xadc_init()hw/arm/xilinx_zynq.c | 6 + hw/misc/Makefile.objs | 1 + hw/misc/zynq_xadc.c | 270 ++++++++++++++++++++++++++++++++++++++++++++ include/hw/misc/zynq_xadc.h | 49 ++++++++ 4 files changed, 326 insertions(+) create mode 100644 hw/misc/zynq_xadc.c create mode 100644 include/hw/misc/zynq_xadc.hhw/arm/xilinx_zynq.c +6
-0@@ -24,6 +24,7 @@#include "hw/block/flash.h" #include "sysemu/block-backend.h" #include "hw/loader.h" +#include "hw/misc/zynq_xadc.h" #include "hw/ssi.h" #include "qemu/error-report.h" @@ -225,6 +226,11 @@ static void zynq_init(MachineState *machine)sysbus_mmio_map (SYS_BUS_DEVICE (dev),0 ,0xE0101000 );sysbus_connect_irq (SYS_BUS_DEVICE (dev),0 , pic[79 -IRQ_OFFSET ]); + dev =qdev_create (NULL ,TYPE_ZYNQ_XADC ); +qdev_init_nofail (dev); +sysbus_mmio_map (SYS_BUS_DEVICE (dev),0 ,0xF8007100 ); +sysbus_connect_irq (SYS_BUS_DEVICE (dev),0 , pic[39 -IRQ_OFFSET ]); + dev =qdev_create (NULL ,"pl330" );qdev_prop_set_uint8 (dev,"num_chnls" ,8 );qdev_prop_set_uint8 (dev,"num_periph_req" ,4 );hw/misc/Makefile.objs +1
-0@@ -36,6 +36,7 @@ obj-$(CONFIG_OMAP) += omap_sdrc.o obj-$(CONFIG_OMAP) += omap_tap.o obj-$(CONFIG_SLAVIO) += slavio_misc.o obj-$(CONFIG_ZYNQ) += zynq_slcr.o +obj-$(CONFIG_ZYNQ) += zynq_xadc.o obj-$(CONFIG_STM32F2XX_SYSCFG) += stm32f2xx_syscfg.o obj-$(CONFIG_PVPANIC) += pvpanic.ohw/misc/zynq_xadc.c new file +11
-0@@ -0,0 +1,270 @@ +/* +* ADC registers for Xilinx Zynq Platform +* +* Copyright (c) 2015 Guenter Roeck +* Based on hw/misc/zynq_slcr.c, written by Michal Simek +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License +* as published by the Free Software Foundation; either version +* 2 of the License, or (at your option) any later version. +*
hw/misc/zynq_xadc.c line 21
Quoted 10 lines
hw/misc/zynq_xadc.c new file +10
-0+* You should have received a copy of the GNU General Public License along +* with this program; if not, see <http://www.gnu.org/licenses/>. +*/ + +#include "hw/hw.h" +#include "hw/misc/zynq_xadc.h" +#include "qemu/timer.h" +#include "sysemu/sysemu.h" + +enum {
These names should match the TRM, which has them as:
hw/misc/zynq_xadc.c line 22
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ CFG = 0x000 / 4,
_CFG (ok)
hw/misc/zynq_xadc.c line 23
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ INTSTS,
_INT_STS (just needs _)
hw/misc/zynq_xadc.c line 24
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ INTMSK,
_INT_MASK
hw/misc/zynq_xadc.c line 25
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ STATUS,
_MSTS
hw/misc/zynq_xadc.c line 26
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ CFIFO,
_CMDFIFO
hw/misc/zynq_xadc.c line 27
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ DFIFO,
_RDFIFO
hw/misc/zynq_xadc.c line 28
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ CTL,
_MCTL
I have dropped the XADCIF_ from the names as that is implicit but the remainder should be recognisable to TRM.
Quoted 4 lines
hw/misc/zynq_xadc.c new file +4
-0+}; + +#define XADC_ZYNQ_CFG_ENABLE BIT(31) +#define XADC_ZYNQ_CFG_CFIFOTH_RD (x) (((x) >> 20) & 0x0f)
hw/misc/zynq_xadc.c line 42
Quoted 10 lines
hw/misc/zynq_xadc.c new file +10
-0+#define XADC_ZYNQ_CFG_DFIFOTH_RD (x) (((x) >> 16) & 0x0f) +#define XADC_ZYNQ_CFG_WEDGE BIT(13) +#define XADC_ZYNQ_CFG_REDGE BIT(12) +#define XADC_ZYNQ_CFG_TCKRATE_DIV2 (0x0 << 8) +#define XADC_ZYNQ_CFG_TCKRATE_DIV4 (0x1 << 8) +#define XADC_ZYNQ_CFG_TCKRATE_DIV8 (0x2 << 8) +#define XADC_ZYNQ_CFG_TCKRATE_DIV16 (0x3 << 8) +#define XADC_ZYNQ_CFG_IGAP_MASK 0x1f +#define XADC_ZYNQ_CFG_IGAP (x) ((x) & XADC_ZYNQ_CFG_IGAP_MASK) +
These defs have the same name stem but, are inconsistent and cannot be used interchangeably. Some, are extractors (CFIFOTH_RD), some are boolean masks (WEDGE) and some are depositors of specific values (TCKRATE_DIV2) It means readers need to refer back to this def table to figure out what the macro operation is for each field. It probably needs a suffix system. _MASK, _EXTRACT, _DEPOSIT. Line wrap is a problem, so maybe truncate to shorthands.
hw/misc/zynq_xadc.c line 45
Quoted 3 lines
hw/misc/zynq_xadc.c new file +3
-0+#define XADC_ZYNQ_INT_CFIFO_LTH BIT(9) +#define XADC_ZYNQ_INT_DFIFO_GTH BIT(8) +#define XADC_ZYNQ_INT_ALARM_MASK 0xff
7f? TRM has OT interrupt as bit 7.
Quoted 6 lines
hw/misc/zynq_xadc.c new file +6
-0+#define XADC_ZYNQ_INT_ALARM_OFFSET 0 + +#define XADC_ZYNQ_STATUS_DFIFO_LVL (x) (((x) & 0x0f) << 12) +#define XADC_ZYNQ_STATUS_CFIFOF BIT(11) +#define XADC_ZYNQ_STATUS_CFIFOE BIT(10) +#define XADC_ZYNQ_STATUS_DFIFOF BIT(9)
hw/misc/zynq_xadc.c line 61
Quoted 10 lines
hw/misc/zynq_xadc.c new file +10
-0+#define XADC_ZYNQ_STATUS_DFIFOE BIT(8) +#define XADC_ZYNQ_STATUS_OT BIT(7) +#define XADC_ZYNQ_STATUS_ALM (x) BIT(x) + +#define XADC_ZYNQ_CTL_RESET BIT(4) + +#define XADC_ZYNQ_CMD_NOP 0x00 +#define XADC_ZYNQ_CMD_READ 0x01 +#define XADC_ZYNQ_CMD_WRITE 0x02 +
Having both ZYNQ and XADC in the name stems in useful if these ever end up in header, but I think it should be reversed, major subsystem (i.e. ZYNQ) first then minor (XADC) for:
ZYNQ_XADC_{REG}_{FIELD}
hw/misc/zynq_xadc.c line 68
Quoted 7 lines
hw/misc/zynq_xadc.c new file +7
-0+static void zynq_xadc_reset (DeviceState *d) +{ +ZynqXADCState *s =ZYNQ_XADC (d); +int i; + + s->regs[CFG ] =XADC_ZYNQ_CFG_IGAP (0x14 ) |XADC_ZYNQ_CFG_TCKRATE_DIV4 | +XADC_ZYNQ_CFG_REDGE ;
Personally prefer to indent one past the = to line up with XADC_ZYNQ_CFG_IGAP.
hw/misc/zynq_xadc.c line 81
Quoted 13 lines
hw/misc/zynq_xadc.c new file +13
-0+ s->regs[INTSTS ] =XADC_ZYNQ_INT_CFIFO_LTH ; + s->regs[INTMSK ] =0xffffffff ; + s->regs[STATUS ] =0 ; + s->regs[CFIFO ] =0 ; + s->regs[DFIFO ] =0 ; + s->regs[CTL ] =XADC_ZYNQ_CTL_RESET ; + +for (i =0 ; i <ARRAY_SIZE (s->xadc_regs); i++) { + s->xadc_regs[i] =0 ; + } +for (i =0 ; i <ARRAY_SIZE (s->xadc_dfifo); i++) { + s->xadc_dfifo[i] =0 ; + }
memset 0.
hw/misc/zynq_xadc.c line 82
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ s->xadc_dfifo_entries =0 ;
_update_ints(). Although see my comment below about the scope of the soft reset for more on this.
Quoted 114 lines
hw/misc/zynq_xadc.c new file +114
-0+} + +static bool zynq_xadc_check_offset (hwaddr offset,bool rnw) +{ +switch (offset) { +case CFG : +case INTMSK : +case INTSTS : +case CTL : +return true; +case DFIFO : +case STATUS : +return rnw;/* read only */ +case CFIFO : +return !rnw;/* write only */ +default : +return false; + } +} + +static void zynq_xadc_update_ints (ZynqXADCState *s) +{ +qemu_set_irq (s->qemu_irq, !!(s->regs[INTSTS ] & ~s->regs[INTMSK ])); +} + +static uint64_t zynq_xadc_read (void *opaque,hwaddr offset,unsigned size) +{ +ZynqXADCState *s = opaque; +int reg = offset /4 ; +uint64_t rv =0 ; +int i; + +if (!zynq_xadc_check_offset (reg, true)) { +qemu_log_mask (LOG_GUEST_ERROR ,"zynq_xadc: Invalid read access to " +" addr %" HWADDR_PRIx"\n" , offset); + } + +switch (reg) { +case CFG : +case INTMSK : +case INTSTS : +case CTL : + rv = s->regs[reg]; +break ; +case STATUS : + rv =XADC_ZYNQ_STATUS_CFIFOE ; + rv |=XADC_ZYNQ_STATUS_DFIFO_LVL (s->xadc_dfifo_entries); +if (!s->xadc_dfifo_entries) { + rv |=XADC_ZYNQ_STATUS_DFIFOE ; + }else if (s->xadc_dfifo_entries >=ARRAY_SIZE (s->xadc_dfifo)) { + rv |=XADC_ZYNQ_STATUS_DFIFOF ; + } +break ; +case DFIFO : + rv = s->xadc_dfifo[0 ]; +if (s->xadc_dfifo_entries >0 ) { + s->xadc_dfifo_entries--; + } +for (i =0 ; i < s->xadc_dfifo_entries; i++) { + s->xadc_dfifo[i] = s->xadc_dfifo[i +1 ]; + } + s->xadc_dfifo[s->xadc_dfifo_entries] =0 ; +zynq_xadc_update_ints (s); +break ; + } +return rv; +} + +static void xadc_add_dfifo (ZynqXADCState *s,uint16_t regval) +{ +if (s->xadc_dfifo_entries <ARRAY_SIZE (s->xadc_dfifo)) { + s->xadc_dfifo[s->xadc_dfifo_entries++] = s->xadc_read_reg_previous; + } + s->xadc_read_reg_previous = regval; +if (s->xadc_dfifo_entries >XADC_ZYNQ_CFG_DFIFOTH_RD (s->regs[CFG ])) { + s->regs[INTSTS ] |=XADC_ZYNQ_INT_DFIFO_GTH ; + } +zynq_xadc_update_ints (s); +} + +static void zynq_xadc_write (void *opaque,hwaddr offset,uint64_t val, +unsigned size) +{ +ZynqXADCState *s = (ZynqXADCState *)opaque; +int reg = offset /4 ; +int xadc_reg; +int xadc_cmd; +int xadc_data; + +if (!zynq_xadc_check_offset (reg, false)) { +qemu_log_mask (LOG_GUEST_ERROR ,"zynq_xadc: Invalid write access to " +"addr %" HWADDR_PRIx"\n" , offset); +return ; + } + +switch (reg) { +case CFG : + s->regs[CFG ] = val; +break ; +case INTSTS : + s->regs[INTSTS ] &= ~val; +zynq_xadc_update_ints (s); +break ; +case INTMSK : + s->regs[INTMSK ] = val &0x003ff ; +zynq_xadc_update_ints (s); +break ; +case CFIFO : + xadc_cmd =extract32 (val,26 ,4 ); + xadc_reg =extract32 (val,16 ,7 ); + xadc_data =extract32 (val,0 ,16 ); + +switch (xadc_cmd) { +case XADC_ZYNQ_CMD_READ :
hw/misc/zynq_xadc.c line 206
Quoted 10 lines
hw/misc/zynq_xadc.c new file +10
-0+xadc_add_dfifo (s, s->xadc_regs[xadc_reg]); +break ; +case XADC_ZYNQ_CMD_WRITE : + s->xadc_regs[xadc_reg] = xadc_data; +break ; +case XADC_ZYNQ_CMD_NOP : +xadc_add_dfifo (s,0 ); +break ; + } + s->regs[INTSTS ] |=XADC_ZYNQ_INT_CFIFO_LTH ;
Worth a comment that ops are instantaneous which is why the FIFO is always empty.
You are however implementing this as a level crossing, that is, when the FIFO level transitions from 1 to 0 you set the interrupt. Given that the reset value is 1 that's probably not how it works. Instead with your instantaneous commands assumption, the correct logic is to just force CFIFO_LTH to always be 1 both on reset and after a WTC of this bit. Otherwise this bit is falsely 0 after being cleared but the FIFO is still empty. The probably applies to DFIFO_GTH. One way to solve this, is to set these two in _update_ints. That is, force CFIFO_LTH to its 1 and do the >= for DFIFO_GTH. That forces the interrupt back up after a clear but when the underlying triggering condition is still true.
Quoted 8 lines
hw/misc/zynq_xadc.c new file +6
-0+zynq_xadc_update_ints (s); +break ; +case CTL : +if (val &XADC_ZYNQ_CTL_RESET ) { +zynq_xadc_reset (DEVICE (s)); + }From the TRM:
"
This bit will reset the communication channel
between the PS and XADC.
If set, the PS-XADC communication channel will
remain in reset until a 0 is written to this bit.
"
Which suggests that this is a level sensitive reset. This logic is only implementing a single reset event on control register write. It is not clear to me whether this is full IP soft-reset and affects the register values (which zynq_xadc_reset does). But whatever the side-effects of this reset are need to be perisistent, i.e. you currently reset all control and xadc registers and purge the fifos, so as long as this bit is set, the core must hold those registers to this value until this is cleared.
Im wondering if the direct registers (_CFG .. _CTL) are not reset by this bit at all, and only the indirect regs (fifo, xadc_regs) are what is reset here? The direct registers are probably under the control of the devcfg and it's reset infrastructure.
So this reset may need to do less, but also need guards on register operations to nop while this bit remains set.
Quoted 1 line
+ s->regs[CTL] = val &
0x00fffeff;
What is up with bit 8?
The TRM has everything other than bit 4 as reserved so if might be cleaner just to RAZWI them all (despite TRM having different types of reserved for different fields). I can't see anything special for bit 8.
Quoted 63 lines
hw/misc/zynq_xadc.c new file +57
-0+break ; + } +} + +static const MemoryRegionOps xadc_ops = { + .read = zynq_xadc_read, + .write = zynq_xadc_write, + .endianness =DEVICE_NATIVE_ENDIAN , +}; + +static void zynq_xadc_init (Object *obj) +{ +SysBusDevice *sbd =SYS_BUS_DEVICE (obj); +ZynqXADCState *s =ZYNQ_XADC (obj); + +memory_region_init_io (&s->iomem, obj, &xadc_ops, s,"xadc" , +ZYNQ_XADC_MMIO_SIZE ); +sysbus_init_mmio (sbd, &s->iomem); +sysbus_init_irq (sbd, &s->qemu_irq); +} + +static const VMStateDescription vmstate_zynq_xadc = { + .name ="zynq_xadc" , + .version_id =1 , + .minimum_version_id =1 , + .fields = (VMStateField []) { +VMSTATE_UINT32_ARRAY (regs, ZynqXADCState,ZYNQ_XADC_NUM_IO_REGS ), +VMSTATE_UINT16_ARRAY (xadc_regs, ZynqXADCState,ZYNQ_XADC_NUM_ADC_REGS ), +VMSTATE_UINT16_ARRAY (xadc_dfifo, ZynqXADCState,ZYNQ_XADC_FIFO_DEPTH ), +VMSTATE_UINT16 (xadc_read_reg_previous, ZynqXADCState), +VMSTATE_UINT16 (xadc_dfifo_entries, ZynqXADCState), +VMSTATE_END_OF_LIST () + } +}; + +static void zynq_xadc_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); + + dc->vmsd = &vmstate_zynq_xadc; + dc->reset = zynq_xadc_reset; +} + +static const TypeInfo zynq_xadc_info = { + .class_init = zynq_xadc_class_init, + .name =TYPE_ZYNQ_XADC , + .parent =TYPE_SYS_BUS_DEVICE , + .instance_size =sizeof (ZynqXADCState), + .instance_init = zynq_xadc_init, +}; + +static void zynq_xadc_register_types (void ) +{ +type_register_static (&zynq_xadc_info); +} + +type_init (zynq_xadc_register_types)include/hw/misc/zynq_xadc.h new file +0
-0
include/hw/misc/zynq_xadc.h line 1
Quoted 1 line
include/hw/misc/zynq_xadc.h new file +1
-0@@ -0,0 +1,49 @@ +/*---------------------------------------------------------------------------
Generally don't have the "----------------" in file header comments.
Regards,
Peter
Quoted 51 lines
include/hw/misc/zynq_xadc.h new file +48
-1+* +* Device model for Zynq ADC controller +* +* Copyright (c) 2015 Guenter Roeck <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License +* as published by the Free Software Foundation; either version +* 2 of the License, or (at your option) any later version. +* +* You should have received a copy of the GNU General Public License along +* with this program; if not, see <http://www.gnu.org/licenses/>. +* +*--------------------------------------------------------------------------- +*/ + +#ifndef ZYNQ_XADC_H +#define ZYNQ_XADC_H + +#include "hw/sysbus.h" + +#define ZYNQ_XADC_MMIO_SIZE 0x0020 +#define ZYNQ_XADC_NUM_IO_REGS (ZYNQ_XADC_MMIO_SIZE / 4) +#define ZYNQ_XADC_NUM_ADC_REGS 128 +#define ZYNQ_XADC_FIFO_DEPTH 15 + +#define TYPE_ZYNQ_XADC "xlnx,zynq_xadc" +#define ZYNQ_XADC (obj) \ + OBJECT_CHECK(ZynqXADCState, (obj), TYPE_ZYNQ_XADC) + +typedef struct ZynqXADCState { +/*< private >*/ +SysBusDevice parent_obj; + +/*< public >*/ +MemoryRegion iomem; + +uint32_t regs[ZYNQ_XADC_NUM_IO_REGS ]; +uint16_t xadc_regs[ZYNQ_XADC_NUM_ADC_REGS ]; +uint16_t xadc_read_reg_previous; +uint16_t xadc_dfifo[ZYNQ_XADC_FIFO_DEPTH ]; +uint16_t xadc_dfifo_entries; + +struct IRQState *qemu_irq; + +}ZynqXADCState ; + +#endif /* ZYNQ_XADC_H */ --2.1.4
I've made a v3 of this, some comments on changes below.
Quoted 57 lines · Peter Crosthwaite
Quoted 56 lines · Guenter Roeck
Add support for the Xilinx XADC core used in Zynq 7000.
References:
- Zynq-7000 All Programmable SoC Technical Reference Manual
- 7 Series FPGAs and Zynq-7000 All Programmable SoC XADC Dual 12-Bit 1 MSPS Analog-to-Digital ConverterTested with Linux using qemu machine xilinx-zynq-a9 with devicetree files zynq-zc702.dtb and zynq-zc706.dtb, and kernel configuration
multi_v7_defconfig.Signed-off-by Guenter Roeck <[email protected]>---
v2: Useextract32()
Mergezynq_xadc_reset()and_zynq_xadc_reset()into one function Use "xlnx,zynq_xadc"
Move device model toinclude/hw/misc/zynq_xadc.h
irq ->qemu_irq
xadc_dfifo_depth->xadc_dfifo_entries
Dropped unnecessary comments
Mergedzynq_xadc_realize()intozynq_xadc_init()hw/arm/xilinx_zynq.c | 6 + hw/misc/Makefile.objs | 1 + hw/misc/zynq_xadc.c | 270 ++++++++++++++++++++++++++++++++++++++++++++ include/hw/misc/zynq_xadc.h | 49 ++++++++ 4 files changed, 326 insertions(+) create mode 100644 hw/misc/zynq_xadc.c create mode 100644 include/hw/misc/zynq_xadc.hhw/arm/xilinx_zynq.c +6
-0@@ -24,6 +24,7 @@#include "hw/block/flash.h" #include "sysemu/block-backend.h" #include "hw/loader.h" +#include "hw/misc/zynq_xadc.h" #include "hw/ssi.h" #include "qemu/error-report.h" @@ -225,6 +226,11 @@ static void zynq_init(MachineState *machine)sysbus_mmio_map (SYS_BUS_DEVICE (dev),0 ,0xE0101000 );sysbus_connect_irq (SYS_BUS_DEVICE (dev),0 , pic[79 -IRQ_OFFSET ]); + dev =qdev_create (NULL ,TYPE_ZYNQ_XADC ); +qdev_init_nofail (dev); +sysbus_mmio_map (SYS_BUS_DEVICE (dev),0 ,0xF8007100 ); +sysbus_connect_irq (SYS_BUS_DEVICE (dev),0 , pic[39 -IRQ_OFFSET ]); + dev =qdev_create (NULL ,"pl330" );qdev_prop_set_uint8 (dev,"num_chnls" ,8 );qdev_prop_set_uint8 (dev,"num_periph_req" ,4 );hw/misc/Makefile.objs +0
-0
Quoted 8 lines
hw/misc/Makefile.objs obj-$(CONFIG_OMAP) += omap_sdrc.o · line 39
Quoted 8 lines
index 4aa76ff..5f76f05 100644
hw/misc/Makefile.objs +1
-0@@ -36,6 +36,7 @@ obj-$(CONFIG_OMAP) += omap_sdrc.o obj-$(CONFIG_OMAP) += omap_tap.o obj-$(CONFIG_SLAVIO) += slavio_misc.o obj-$(CONFIG_ZYNQ) += zynq_slcr.o +obj-$(CONFIG_ZYNQ) += zynq_xadc.o
Changed this to - separator.
Quoted 56 lines
Quoted 20 lines
hw/misc/Makefile.objs +0
-0obj-$(CONFIG_STM32F2XX_SYSCFG) += stm32f2xx_syscfg.o obj-$(CONFIG_PVPANIC) += pvpanic.ohw/misc/zynq_xadc.c new file +11
-0@@ -0,0 +1,270 @@ +/* +* ADC registers for Xilinx Zynq Platform +* +* Copyright (c) 2015 Guenter Roeck +* Based on hw/misc/zynq_slcr.c, written by Michal Simek +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License +* as published by the Free Software Foundation; either version +* 2 of the License, or (at your option) any later version. +* hw/misc/zynq_xadc.c line 21
Quoted 10 lines
hw/misc/zynq_xadc.c new file +10
-0+* You should have received a copy of the GNU General Public License along +* with this program; if not, see <http://www.gnu.org/licenses/>. +*/ + +#include "hw/hw.h" +#include "hw/misc/zynq_xadc.h" +#include "qemu/timer.h" +#include "sysemu/sysemu.h" + +enum {These names should match the TRM, which has them as:
hw/misc/zynq_xadc.c line 22
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ CFG = 0x000 / 4,
_CFG(ok)hw/misc/zynq_xadc.c line 23
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ INTSTS,
_INT_STS(just needs _)hw/misc/zynq_xadc.c line 24
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ INTMSK,
_INT_MASKhw/misc/zynq_xadc.c line 25
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ STATUS,
_MSTShw/misc/zynq_xadc.c line 26
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ CFIFO,
_CMDFIFOhw/misc/zynq_xadc.c line 27
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ DFIFO,
Quoted 9 lines
_RDFIFOhw/misc/zynq_xadc.c line 28
Quoted 1 line
hw/misc/zynq_xadc.c new file +1
-0+ CTL,
_MCTLI have dropped the
XADCIF_from the names as that is implicit but the remainder should be recognisable to TRM.
Fixed all.
Quoted 15 lines
Quoted 4 lines
hw/misc/zynq_xadc.c new file +4
-0+}; + +#define XADC_ZYNQ_CFG_ENABLE BIT(31) +#define XADC_ZYNQ_CFG_CFIFOTH_RD (x) (((x) >> 20) & 0x0f)hw/misc/zynq_xadc.c line 42
Quoted 10 lines
hw/misc/zynq_xadc.c new file +10
-0+#define XADC_ZYNQ_CFG_DFIFOTH_RD (x) (((x) >> 16) & 0x0f) +#define XADC_ZYNQ_CFG_WEDGE BIT(13) +#define XADC_ZYNQ_CFG_REDGE BIT(12) +#define XADC_ZYNQ_CFG_TCKRATE_DIV2 (0x0 << 8) +#define XADC_ZYNQ_CFG_TCKRATE_DIV4 (0x1 << 8) +#define XADC_ZYNQ_CFG_TCKRATE_DIV8 (0x2 << 8) +#define XADC_ZYNQ_CFG_TCKRATE_DIV16 (0x3 << 8) +#define XADC_ZYNQ_CFG_IGAP_MASK 0x1f +#define XADC_ZYNQ_CFG_IGAP (x) ((x) & XADC_ZYNQ_CFG_IGAP_MASK) +
Quoted 8 lines
These defs have the same name stem but, are inconsistent and cannot be used interchangeably. Some, are extractors (
CFIFOTH_RD), some are boolean masks (WEDGE) and some are depositors of specific values (TCKRATE_DIV2) It means readers need to refer back to this def table to figure out what the macro operation is for each field. It probably needs a suffix system._MASK,_EXTRACT,_DEPOSIT. Line wrap is a problem, so maybe truncate to shorthands.
Reduced all defs to either a single bit mask, or a _SHIFT _LENGTH pair for consistency. The clients then shift them as needed.
I dropped the XADC_ZYNQ_ in the end, as local macros shouldn't need to worry about it. We need to think harder about having programmers model macros in the global namespace as the text bloat if we have to preface everything is out of control.
Quoted 6 lines
hw/misc/zynq_xadc.c line 45
Quoted 3 lines
hw/misc/zynq_xadc.c new file +3
-0+#define XADC_ZYNQ_INT_CFIFO_LTH BIT(9) +#define XADC_ZYNQ_INT_DFIFO_GTH BIT(8) +#define XADC_ZYNQ_INT_ALARM_MASK 0xff7f? TRM has OT interrupt as bit 7.
Fixed.
Quoted 23 lines
Quoted 6 lines
hw/misc/zynq_xadc.c new file +6
-0+#define XADC_ZYNQ_INT_ALARM_OFFSET 0 + +#define XADC_ZYNQ_STATUS_DFIFO_LVL (x) (((x) & 0x0f) << 12) +#define XADC_ZYNQ_STATUS_CFIFOF BIT(11) +#define XADC_ZYNQ_STATUS_CFIFOE BIT(10) +#define XADC_ZYNQ_STATUS_DFIFOF BIT(9)hw/misc/zynq_xadc.c line 61
Quoted 10 lines
hw/misc/zynq_xadc.c new file +10
-0+#define XADC_ZYNQ_STATUS_DFIFOE BIT(8) +#define XADC_ZYNQ_STATUS_OT BIT(7) +#define XADC_ZYNQ_STATUS_ALM (x) BIT(x) + +#define XADC_ZYNQ_CTL_RESET BIT(4) + +#define XADC_ZYNQ_CMD_NOP 0x00 +#define XADC_ZYNQ_CMD_READ 0x01 +#define XADC_ZYNQ_CMD_WRITE 0x02 +Having both ZYNQ and XADC in the name stems in useful if these ever end up in header, but I think it should be reversed, major subsystem (i.e. ZYNQ) first then minor (XADC) for:
ZYNQ_XADC_{REG}_{FIELD}
Quoted 10 lines
hw/misc/zynq_xadc.c line 68
Quoted 7 lines
hw/misc/zynq_xadc.c new file +7
-0+static void zynq_xadc_reset (DeviceState *d) +{ +ZynqXADCState *s =ZYNQ_XADC (d); +int i; + + s->regs[CFG ] =XADC_ZYNQ_CFG_IGAP (0x14 ) |XADC_ZYNQ_CFG_TCKRATE_DIV4 | +XADC_ZYNQ_CFG_REDGE ;Personally prefer to indent one past the = to line up with
XADC_ZYNQ_CFG_IGAP.
Fixed.
Quoted 4 lines
hw/misc/zynq_xadc.c line 71
Quoted 4 lines
hw/misc/zynq_xadc.c new file +3
-0+ s->regs[INTSTS ] =XADC_ZYNQ_INT_CFIFO_LTH ; + s->regs[INTMSK ] =0xffffffff ; + s->regs[STATUS ] =0 ;
Status doesn't have persistent state so dropped this one.
Quoted 11 lines
hw/misc/zynq_xadc.c line 81
Quoted 10 lines
hw/misc/zynq_xadc.c new file +10
-0+ s->regs[CFIFO ] =0 ; + s->regs[DFIFO ] =0 ; + s->regs[CTL ] =XADC_ZYNQ_CTL_RESET ; + +for (i =0 ; i <ARRAY_SIZE (s->xadc_regs); i++) { + s->xadc_regs[i] =0 ; + } +for (i =0 ; i <ARRAY_SIZE (s->xadc_dfifo); i++) { + s->xadc_dfifo[i] =0 ; + }
Quoted 2 lines
memset 0.
Fixed.
Quoted 5 lines
Quoted 1 line
+
s->xadc_dfifo_entries= 0;
_update_ints(). Although see my comment below about the scope of the soft reset for more on this.
Fixed.
Quoted 57 lines
Quoted 57 lines
hw/misc/zynq_xadc.c new file +57
-0+} + +static bool zynq_xadc_check_offset (hwaddr offset,bool rnw) +{ +switch (offset) { +case CFG : +case INTMSK : +case INTSTS : +case CTL : +return true; +case DFIFO : +case STATUS : +return rnw;/* read only */ +case CFIFO : +return !rnw;/* write only */ +default : +return false; + } +} + +static void zynq_xadc_update_ints (ZynqXADCState *s) +{ +qemu_set_irq (s->qemu_irq, !!(s->regs[INTSTS ] & ~s->regs[INTMSK ])); +} + +static uint64_t zynq_xadc_read (void *opaque,hwaddr offset,unsigned size) +{ +ZynqXADCState *s = opaque; +int reg = offset /4 ; +uint64_t rv =0 ; +int i; + +if (!zynq_xadc_check_offset (reg, true)) { +qemu_log_mask (LOG_GUEST_ERROR ,"zynq_xadc: Invalid read access to " +" addr %" HWADDR_PRIx"\n" , offset); + } + +switch (reg) { +case CFG : +case INTMSK : +case INTSTS : +case CTL : + rv = s->regs[reg]; +break ; +case STATUS : + rv =XADC_ZYNQ_STATUS_CFIFOE ; + rv |=XADC_ZYNQ_STATUS_DFIFO_LVL (s->xadc_dfifo_entries); +if (!s->xadc_dfifo_entries) { + rv |=XADC_ZYNQ_STATUS_DFIFOE ; + }else if (s->xadc_dfifo_entries >=ARRAY_SIZE (s->xadc_dfifo)) { + rv |=XADC_ZYNQ_STATUS_DFIFOF ; + } +break ; +case DFIFO : + rv = s->xadc_dfifo[0 ]; +if (s->xadc_dfifo_entries >0 ) { + s->xadc_dfifo_entries--;
Quoted 8 lines
hw/misc/zynq_xadc.c line 147
Quoted 8 lines
hw/misc/zynq_xadc.c new file +8
-0+ } +for (i =0 ; i < s->xadc_dfifo_entries; i++) { + s->xadc_dfifo[i] = s->xadc_dfifo[i +1 ]; + } + s->xadc_dfifo[s->xadc_dfifo_entries] =0 ; +zynq_xadc_update_ints (s); +break ; + }
For symmetry with the fifo add data helper I factored this out into a helper as well. Changed naming scheme to "push" and "pop".
Quoted 7 lines
hw/misc/zynq_xadc.c line 154
Quoted 7 lines
hw/misc/zynq_xadc.c new file +7
-0+return rv; +} + +static void xadc_add_dfifo (ZynqXADCState *s,uint16_t regval) +{ +if (s->xadc_dfifo_entries <ARRAY_SIZE (s->xadc_dfifo)) { + s->xadc_dfifo[s->xadc_dfifo_entries++] = s->xadc_read_reg_previous;
Size 8 tab reduced to 4.
Quoted 6 lines
hw/misc/zynq_xadc.c line 159
Quoted 6 lines
hw/misc/zynq_xadc.c new file +5
-0+ } + s->xadc_read_reg_previous = regval; +if (s->xadc_dfifo_entries >XADC_ZYNQ_CFG_DFIFOTH_RD (s->regs[CFG ])) { + s->regs[INTSTS ] |=XADC_ZYNQ_INT_DFIFO_GTH ; + }
Moved to update_ints. This catches the case where the threshold itself changes to below the trigger level.
Quoted 13 lines
Quoted 13 lines
hw/misc/zynq_xadc.c new file +13
-0+zynq_xadc_update_ints (s); +} + +static void zynq_xadc_write (void *opaque,hwaddr offset,uint64_t val, +unsigned size) +{ +ZynqXADCState *s = (ZynqXADCState *)opaque; +int reg = offset /4 ; +int xadc_reg; +int xadc_cmd; +int xadc_data; + +if (!zynq_xadc_check_offset (reg, false)) {
Quoted 8 lines
hw/misc/zynq_xadc.c line 180
Quoted 8 lines
hw/misc/zynq_xadc.c new file +8
-0+qemu_log_mask (LOG_GUEST_ERROR ,"zynq_xadc: Invalid write access to " +"addr %" HWADDR_PRIx"\n" , offset); +return ; + } + +switch (reg) { +case CFG : + s->regs[CFG ] = val;
The CFG register contains the threshold levels, so changing it could trigger an interrupt. As pretty much every write can have interrupt consequences, I have just put a catchall of _update_ints after the switch.
Quoted 4 lines
Quoted 4 lines
hw/misc/zynq_xadc.c new file +4
-0+break ; +case INTSTS : + s->regs[INTSTS ] &= ~val; +zynq_xadc_update_ints (s);
Quoted 8 lines
hw/misc/zynq_xadc.c line 192
Quoted 8 lines
hw/misc/zynq_xadc.c new file +8
-0+break ; +case INTMSK : + s->regs[INTMSK ] = val &0x003ff ; +zynq_xadc_update_ints (s); +break ; +case CFIFO : + xadc_cmd =extract32 (val,26 ,4 ); + xadc_reg =extract32 (val,16 ,7 );
The TRM has this field as 10 bits. I have change this to a 10-bit extract and implement the GUEST_ERROR on out-of-bounds to make it easier to extend if needed.
Quoted 10 lines
hw/misc/zynq_xadc.c line 201
Quoted 10 lines
hw/misc/zynq_xadc.c new file +9
-0+ xadc_data =extract32 (val,0 ,16 ); + +switch (xadc_cmd) { +case XADC_ZYNQ_CMD_READ : +xadc_add_dfifo (s, s->xadc_regs[xadc_reg]); +break ; +case XADC_ZYNQ_CMD_WRITE : + s->xadc_regs[xadc_reg] = xadc_data; +break ;
I read the TRM a little closer, and it seems that writes push dummy data to the RDFIFO, the same as NOPs. So this fallsthrough I think.
Quoted 9 lines
hw/misc/zynq_xadc.c line 206
Quoted 5 lines
hw/misc/zynq_xadc.c new file +5
-0+case XADC_ZYNQ_CMD_NOP : +xadc_add_dfifo (s,0 ); +break ; + } + s->regs[INTSTS ] |=XADC_ZYNQ_INT_CFIFO_LTH ;Worth a comment that ops are instantaneous which is why the FIFO is always empty.
Quoted 12 lines
You are however implementing this as a level crossing, that is, when the FIFO level transitions from 1 to 0 you set the interrupt. Given that the reset value is 1 that's probably not how it works. Instead with your instantaneous commands assumption, the correct logic is to just force
CFIFO_LTHto always be 1 both on reset and after a WTC of this bit. Otherwise this bit is falsely 0 after being cleared but the FIFO is still empty. The probably applies toDFIFO_GTH. One way to solve this, is to set these two in_update_ints. That is, forceCFIFO_LTHto its 1 and do the >= forDFIFO_GTH. That forces the interrupt back up after a clear but when the underlying triggering condition is still true.
Both fixed. CFIFO_LTH is hardwired 1 in update_ints and the DFIFO_GTH test is done there as well.
Quoted 25 lines
hw/misc/zynq_xadc.c line 212
Quoted 6 lines
hw/misc/zynq_xadc.c new file +6
-0+zynq_xadc_update_ints (s); +break ; +case CTL : +if (val &XADC_ZYNQ_CTL_RESET ) { +zynq_xadc_reset (DEVICE (s)); + }From the TRM:
"
This bit will reset the communication channel
between the PS and XADC.
If set, the PS-XADC communication channel will
remain in reset until a 0 is written to this bit.
"Which suggests that this is a level sensitive reset. This logic is only implementing a single reset event on control register write. It is not clear to me whether this is full IP soft-reset and affects the register values (which
zynq_xadc_resetdoes). But whatever the side-effects of this reset are need to be perisistent, i.e. you currently reset all control and xadc registers and purge the fifos, so as long as this bit is set, the core must hold those registers to this value until this is cleared.
Quoted 8 lines
Im wondering if the direct registers (
_CFG.._CTL) are not reset by this bit at all, and only the indirect regs (fifo,xadc_regs) are what is reset here? The direct registers are probably under the control of the devcfg and it's reset infrastructure.So this reset may need to do less, but also need guards on register operations to nop while this bit remains set.
So on closer examination, this reset maybe resetting even less than I thought. The docs aren't exactly clear, but it only resets the "communications channel", which suggests to me it doesnt reset state in either of the ends of the communication. So xadc_regs and the dfifo should be unaffected. No comms channel to me suggests that commands will do nothing, so I changed this to simple ignore commands (not even a NOP) and GUEST_ERROR when the reset is held.
Quoted 9 lines
Quoted 1 line
+ s->regs[CTL] = val &
0x00fffeff;What is up with bit 8?
The TRM has everything other than bit 4 as reserved so if might be cleaner just to RAZWI them all (despite TRM having different types of reserved for different fields). I can't see anything special for bit 8.
I left this for now.
Quoted 8 lines
Quoted 8 lines
hw/misc/zynq_xadc.c new file +8
-0+break ; + } +} + +static const MemoryRegionOps xadc_ops = { + .read = zynq_xadc_read, + .write = zynq_xadc_write, + .endianness =DEVICE_NATIVE_ENDIAN ,
Quoted 8 lines
hw/misc/zynq_xadc.c line 229
Quoted 8 lines
hw/misc/zynq_xadc.c new file +8
-0+}; + +static void zynq_xadc_init (Object *obj) +{ +SysBusDevice *sbd =SYS_BUS_DEVICE (obj); +ZynqXADCState *s =ZYNQ_XADC (obj); + + memory_region_init_io(&s->iomem, obj, &xadc_ops, s, "xadc",
Changed to "zynq-xadc"
Quoted 7 lines
hw/misc/zynq_xadc.c line 236
Quoted 7 lines
hw/misc/zynq_xadc.c new file +7
-0+ ZYNQ_XADC_MMIO_SIZE); +sysbus_init_mmio (sbd, &s->iomem); +sysbus_init_irq (sbd, &s->qemu_irq); +} + +static const VMStateDescription vmstate_zynq_xadc = { + .name ="zynq_xadc" ,
Changed to "zynq-xadc"
Quoted 35 lines
Quoted 35 lines
hw/misc/zynq_xadc.c new file +34
-0+ .version_id = 1, + .minimum_version_id = 1, + .fields = (VMStateField []) { +VMSTATE_UINT32_ARRAY (regs, ZynqXADCState,ZYNQ_XADC_NUM_IO_REGS ), +VMSTATE_UINT16_ARRAY (xadc_regs, ZynqXADCState,ZYNQ_XADC_NUM_ADC_REGS ), +VMSTATE_UINT16_ARRAY (xadc_dfifo, ZynqXADCState,ZYNQ_XADC_FIFO_DEPTH ), +VMSTATE_UINT16 (xadc_read_reg_previous, ZynqXADCState), +VMSTATE_UINT16 (xadc_dfifo_entries, ZynqXADCState), +VMSTATE_END_OF_LIST () + } +}; + +static void zynq_xadc_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); + + dc->vmsd = &vmstate_zynq_xadc; + dc->reset = zynq_xadc_reset; +} + +static const TypeInfo zynq_xadc_info = { + .class_init = zynq_xadc_class_init, + .name =TYPE_ZYNQ_XADC , + .parent =TYPE_SYS_BUS_DEVICE , + .instance_size =sizeof (ZynqXADCState), + .instance_init = zynq_xadc_init, +}; + +static void zynq_xadc_register_types (void ) +{ +type_register_static (&zynq_xadc_info); +} + +type_init (zynq_xadc_register_types)include/hw/misc/zynq_xadc.h +0
-0
Quoted 9 lines
include/hw/misc/zynq_xadc.h line 1
Quoted 6 lines
new file mode 100644
index 0000000..495be06include/hw/misc/zynq_xadc.h new file +1
-0@@ -0,0 +1,49 @@ +/*--------------------------------------------------------------------------- Generally don't have the "----------------" in file header comments.
Fixed.
Quoted 22 lines
Regards,
PeterQuoted 19 lines
include/hw/misc/zynq_xadc.h new file +19
-0+* +* Device model for Zynq ADC controller +* +* Copyright (c) 2015 Guenter Roeck <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License +* as published by the Free Software Foundation; either version +* 2 of the License, or (at your option) any later version. +* +* You should have received a copy of the GNU General Public License along +* with this program; if not, see <http://www.gnu.org/licenses/>. +* +*--------------------------------------------------------------------------- +*/ + +#ifndef ZYNQ_XADC_H +#define ZYNQ_XADC_H +
Quoted 8 lines
include/hw/misc/zynq_xadc.h line 28
Quoted 8 lines
include/hw/misc/zynq_xadc.h new file +8
-0+#include "hw/sysbus.h" + +#define ZYNQ_XADC_MMIO_SIZE 0x0020 +#define ZYNQ_XADC_NUM_IO_REGS (ZYNQ_XADC_MMIO_SIZE / 4) +#define ZYNQ_XADC_NUM_ADC_REGS 128 +#define ZYNQ_XADC_FIFO_DEPTH 15 + +#define TYPE_ZYNQ_XADC "xlnx,zynq_xadc"
"-"'d.
Regards,
Peter
Quoted 24 lines
Quoted 24 lines
include/hw/misc/zynq_xadc.h new file +21
-1+#define ZYNQ_XADC (obj) \ + OBJECT_CHECK(ZynqXADCState, (obj), TYPE_ZYNQ_XADC) + +typedef struct ZynqXADCState { +/*< private >*/ +SysBusDevice parent_obj; + +/*< public >*/ +MemoryRegion iomem; + +uint32_t regs[ZYNQ_XADC_NUM_IO_REGS ]; +uint16_t xadc_regs[ZYNQ_XADC_NUM_ADC_REGS ]; +uint16_t xadc_read_reg_previous; +uint16_t xadc_dfifo[ZYNQ_XADC_FIFO_DEPTH ]; +uint16_t xadc_dfifo_entries; + +struct IRQState *qemu_irq; + +}ZynqXADCState ; + +#endif /* ZYNQ_XADC_H */ --2.1.4
Quoted 1 line · Peter Crosthwaite
I've made a v3 of this, some comments on changes below.
The v3 seems to have never hit the list?
thanks
-- PMM