rpi2 support

Thanks for the quick replies
rpi have only sold 7M, so not that big in the grand scheme of things But the rpi2 has only been out for 8 months,
I am sure it will be popular

And now,, out only a few days,, the pizero, a $5 board Essentially an "A" without networking but 40 GPIO pin header I bet they will sell a lot of them (BCM2835)

For me, I think I will do some version of kexec, there are 3
A bootloader is kind of overkill, sledgehammer to kill flies thanks
dave thompson

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox

Hi,

I tried a dirty hack, because bcm2835 and bcm2836 are very similar:

index 134ad9b..aa610da 100644
@@ -9,6 +9,7 @@ choice
 
 config MACH_RPI
        bool "RaspberryPi (BCM2835/ARM1176JZF-S)"
+       select CPU_V7
 
 endchoice
 

index e55085a..ee77f1e 100644
@@ -28,7 +28,7 @@
  * This file is manually generated.
  */
 
-#define BCM2835_PERI_BASE      0x20000000
+#define BCM2835_PERI_BASE      0x3f000000
 #define BCM2835_ST_BASE                (BCM2835_PERI_BASE + 0x3000)    /* System Timer */
 #define BCM2835_DMA_BASE       (BCM2835_PERI_BASE + 0x7000)    /* DMA controller */
 #define BCM2835_ARM_BASE       (BCM2835_PERI_BASE + 0xB000)    /* BCM2708 ARM control block */

---

After that I get some printout:

# mbox: Timeout waiting for response
bcm2835: Could not query board revision
mbox: Timeout waiting for response
regulator-bcm2835 regulator-bcm2835: bcm2835: Could not set module 1 power state uart-pl011 uart0-pl0110: probe failed: Connection timed out
mbox: Timeout waiting for response
mbox: Timeout waiting for response
could not query ARM memory size
initcall rpi_mem_init+0x0/0x7c failed: Connection timed out bcm2835-gpio bcm2835-gpio0: probed gpiochip0 with base 0
malloc space: 0x03c00000 -> 0x03ffffff (size 4 MiB)
bcm2835_mci bcm2835_mci0: clock not found: -2
bcm2835_mci bcm2835_mci0: probe failed: No such file or directory no /dev/disk0.0. using default env
environment load /dev/env0: No such file or directory
Maybe you have to create the partition.
running /env/bin/init...

Hit m for menu or any other key to stop autoboot: 0
blspec: blspec_scan_directory: net loader/entries
ifup: No such file or directory
running automount command 'ifup eth0 && mount -t tftp $eth0.serverip /mnt/tftp' failed
global: set parameter dhcp.vendor_id: Invalid argument
ifup: No such file or directory
running automount command 'ifup eth0 && mount -t tftp $eth0.serverip /mnt/tftp' failed could not open /mnt/tftp/none-linux-rpi: No such file or directory Booting net failed: No such file or directory
booting net failed: No such file or directory
boot: No such file or directory

type exit to get to the menu

                            barebox@<NULL>:/

#

---

Maybe a good point to start. :-)

- Alex

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox