ALSA: hda - hdmi jack support for dynamic pcm assignment
Subsystems (2)
cover ALSA: hda - hdmi jack support for dynamic pcm assignment
From: Libin Yang <[email protected]>
The patchset adds hdmi jack support for dynamic pcm assignment
Libin Yang (4):
ALSA: Add documentation about HD-audio DP MST
ALSA: hda - add hdmi_pcm to manage hdmi pcm related features
ALSA: hda - hdmi jack created based on pcm
ALSA: hda - hdmi monitor hotplug support for dynamic pcm assignment
Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt | 75 +++++++ sound/pci/hda/patch_hdmi.c | 229 +++++++++++++++------ 2 files changed, 243 insertions(+), 61 deletions(-) create mode 100644 Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt
Signature · 1 line
1.9.1
PATCH 1/4 ALSA: Add documentation about HD-audio DP MST
From: Libin Yang <[email protected]>
Add the documentation about HD-audio DP MST:
1. Overview
2. Jack
Others will be added later.
--- Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt | 78 ++++++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt
Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt new file +78 -0
@@ -0,0 +1,78 @@ +To support DP MST audio, HD Audio hdmi codec driver introduces virtual pin +and dynamic pcm assignment. + +Virtual pin is an extension of per_pin. The most difference of DP MST +from legacy is that DP MST introduces device entry. Each pin can contain +several device entries. Each device entry behaves as a pin. + +As each pin may contain several device entries and each codec may contain +several pins, if we use one pcm per per_pin, there will be many PCMs. +The new solution is to create a few PCMs and to dynamically bind pcm to +per_pin. Driver uses spec->dyn_pcm_assign flag to indicate whether to use +the new solution. + +PCM +=== +To be added + + +Jack +==== + +Presume: + - MST must be dyn_pcm_assign, it can be acomp or !acomp; + - NON-MST may or may not be dyn_pcm_assign, it can be acomp or !acomp; + +So there are the following scenarios: + a.MST (&& dyn_pcm_assign) && acomp + b.MST (&& dyn_pcm_assign) && !acomp + c.NON-MST && dyn_pcm_assign && acomp + d.NON-MST && dyn_pcm_assign && !acomp + e.NON-MST && !dyn_pcm_assign && acomp + f.NON-MST && !dyn_pcm_assign && !acomp + +Below discussion will ignore MST and NON-MST difference as it doesn't +impact on jack handling too much. + +Driver uses new struct hdmi_pcm pcm[] array in hdmi_spec and snd_jack is +a member of hdmi_pcm. Each pin has one struct hdmi_pcm * pcm pointer. + +For !dyn_pcm_assign, per_pin->pcm will assigned to spec->pcm[n] statically. + +For dyn_pcm_assign, per_pin->pcm will assigned to spec->pcm[n] +when monitor is hotplugged. + + +Build Jack +---------- + +Build jack based on the pcm. acomp or !acomp will not impact on jack buiding. +- dyn_pcm_assign +Will not use hda_jack but use snd_jack in spec->pcm_rec[pcm_idx].jack directly. + +- !dyn_pcm_assign +Use hda_jack and assign spec->pcm_rec[pcm_idx].jack = jack->jack statically. + + +Unsolicited Event Enabling +-------------------------- +Enable unsolicited event if !acomp. + + +Monitor Hotplug Event Handling +------------------------------ +- acomp +pin_eld_notify() -> check_presence_and_report() -> hdmi_present_sense() -> +sync_eld_via_acomp(). +Use directly snd_jack_report() on spec->pcm_rec[pcm_idx].jack for +both dyn_pcm_assign and !dyn_pcm_assign + +- !acomp +Hdmi_unsol_event() -> hdmi_intrinsic_event() -> check_presence_and_report() -> +hdmi_present_sense() -> hdmi_prepsent_sense_via_verbs() +Use directly snd_jack_report() on spec->pcm_rec[pcm_idx].jack for dyn_pcm_assign. +Use hda_jack mechanism to handle jack events. + + +Others to be added later +========================
Signature · 1 line
1.9.1
PATCH 2/4 ALSA: hda - add hdmi_pcm to manage hdmi pcm related features
In reply to [email protected]From: Libin Yang <[email protected]>
Use struct hdmi_pcm wrapper for hdmi pcm management.
All PCM related features, like jack, will be put in this structure.
--- sound/pci/hda/patch_hdmi.c | 44 ++++++++++++++++++++++++-------------------- 1 file changed, 24 insertions(+), 20 deletions(-)
sound/pci/hda/patch_hdmi.c +24 -20
@@ -86,7 +86,7 @@ struct hdmi_spec_per_pin {struct delayed_work work;struct snd_kcontrol *eld_ctl;struct snd_jack *acomp_jack;/* jack via audio component */ -struct hda_pcm *pcm;/* pointer to spec->pcm_rec[n] dynamically*/ +struct hdmi_pcm *pcm;/* pointer to spec->pcm_rec[n] dynamically*/ int pcm_idx;/* which pcm is attached. -1 means no pcm is attached */ int repoll_count;bool setup;/* the stream has been set up by prepare callback */
@@ -132,6 +132,11 @@ struct hdmi_ops {int (*chmap_validate)(int ca,int channels,unsigned char *chmap); }; +struct hdmi_pcm { +struct hda_pcm *pcm; +struct snd_jack *jack; +}; +struct hdmi_spec {int num_cvts;struct snd_array cvts;/* struct hdmi_spec_per_cvt */
@@ -139,7 +144,7 @@ struct hdmi_spec {int num_pins;struct snd_array pins;/* struct hdmi_spec_per_pin */ -struct hda_pcm *pcm_rec[16 ]; +struct hdmi_pcm pcm_rec[16 ];struct mutex pcm_lock;/* pcm_bitmap means which pcms have been assigned to pins*/ unsigned long pcm_bitmap;
@@ -403,7 +408,7 @@ static int hinfo_to_pcm_index(struct hda_codec *codec,int pcm_idx;for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) -if (get_pcm_rec (spec, pcm_idx)->stream == hinfo) +if (get_pcm_rec (spec, pcm_idx).pcm->stream == hinfo)return pcm_idx;codec_warn (codec,"HDMI: hinfo %p not registered\n" , hinfo);
@@ -419,7 +424,8 @@ static int hinfo_to_pin_index(struct hda_codec *codec,for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) { per_pin =get_pin (spec, pin_idx); -if (per_pin->pcm && per_pin->pcm->stream == hinfo) +if (per_pin->pcm && + per_pin->pcm->pcm->stream == hinfo)return pin_idx; }
@@ -1721,7 +1727,7 @@ static void hdmi_attach_hda_pcm(struct hdmi_spec *spec,if (idx == -ENODEV )return ; per_pin->pcm_idx = idx; - per_pin->pcm = spec->pcm_rec[idx]; + per_pin->pcm = &spec->pcm_rec[idx];set_bit (idx, &spec->pcm_bitmap); }
@@ -1764,7 +1770,7 @@ static void hdmi_pcm_setup_pin(struct hdmi_spec *spec,bool non_pcm;if (per_pin->pcm_idx >=0 && per_pin->pcm_idx < spec->pcm_used) - pcm = spec->pcm_rec[per_pin->pcm_idx]; + pcm = spec->pcm_rec[per_pin->pcm_idx].pcm;else return ;if (!test_bit (per_pin->pcm_idx, &spec->pcm_in_use))
@@ -2028,8 +2034,10 @@ static int hdmi_add_pin(struct hda_codec *codec, hda_nid_t pin_nid) per_pin->non_pcm = false;if (spec->dyn_pcm_assign) per_pin->pcm_idx =-1 ; -else +else { + per_pin->pcm = &spec->pcm_rec[pin_idx]; per_pin->pcm_idx = pin_idx; + } per_pin->pin_nid_idx = pin_idx; err =hdmi_read_pin_conn (codec, pin_idx);
@@ -2439,7 +2447,6 @@ static int hdmi_chmap_ctl_put(struct snd_kcontrol *kcontrol,static int generic_hdmi_build_pcms (struct hda_codec *codec) {struct hdmi_spec *spec = codec->spec; -struct hdmi_spec_per_pin *per_pin;int pin_idx;for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) {
@@ -2449,11 +2456,8 @@ static int generic_hdmi_build_pcms(struct hda_codec *codec) info =snd_hda_codec_pcm_new (codec,"HDMI %d" , pin_idx);if (!info)return -ENOMEM ; -if (!spec->dyn_pcm_assign) { - per_pin =get_pin (spec, pin_idx); - per_pin->pcm = info; - } - spec->pcm_rec[pin_idx] = info; + + spec->pcm_rec[pin_idx].pcm = info; spec->pcm_used++; info->pcm_type =HDA_PCM_TYPE_HDMI ; info->own_chmap = true;
@@ -2496,7 +2500,7 @@ static int generic_hdmi_build_jack(struct hda_codec *codec, int pin_idx)char hdmi_str[32 ] ="HDMI/DP" ;struct hdmi_spec *spec = codec->spec;struct hdmi_spec_per_pin *per_pin =get_pin (spec, pin_idx); -int pcmdev =get_pcm_rec (spec, pin_idx)->device; +int pcmdev =get_pcm_rec (spec, pin_idx).pcm->device;bool phantom_jack;if (pcmdev >0 )
@@ -2536,7 +2540,7 @@ static int generic_hdmi_build_controls(struct hda_codec *codec)/* add control for ELD Bytes */ err =hdmi_create_eld_ctl (codec, pin_idx, -get_pcm_rec (spec, pin_idx)->device); +get_pcm_rec (spec, pin_idx).pcm->device);if (err <0 )return err;
@@ -2551,7 +2555,7 @@ static int generic_hdmi_build_controls(struct hda_codec *codec)struct snd_kcontrol *kctl;int i; - pcm = spec->pcm_rec[pin_idx]; + pcm = spec->pcm_rec[pin_idx].pcm;if (!pcm || !pcm->pcm)break ; err = snd_pcm_add_chmap_ctls(pcm->pcm,
@@ -2857,7 +2861,7 @@ static int simple_playback_build_pcms(struct hda_codec *codec) info =snd_hda_codec_pcm_new (codec,"HDMI 0" );if (!info)return -ENOMEM ; - spec->pcm_rec[0 ] = info; + spec->pcm_rec[0 ].pcm = info; info->pcm_type =HDA_PCM_TYPE_HDMI ; pstr = &info->stream[SNDRV_PCM_STREAM_PLAYBACK ]; *pstr = spec->pcm_playback;
@@ -3306,7 +3310,7 @@ static int nvhdmi_7x_8ch_build_pcms(struct hda_codec *codec)struct hdmi_spec *spec = codec->spec;int err =simple_playback_build_pcms (codec);if (!err) { -struct hda_pcm *info =get_pcm_rec (spec,0 ); +struct hda_pcm *info =get_pcm_rec (spec,0 ).pcm; info->own_chmap = true; }return err;
@@ -3324,7 +3328,7 @@ static int nvhdmi_7x_8ch_build_controls(struct hda_codec *codec)return err;/* add channel maps */ - info =get_pcm_rec (spec,0 ); + info =get_pcm_rec (spec,0 ).pcm; err =snd_pcm_add_chmap_ctls (info->pcm,SNDRV_PCM_STREAM_PLAYBACK , snd_pcm_alt_chmaps,8 ,0 , &chmap);
@@ -3522,7 +3526,7 @@ static struct hda_pcm *hda_find_pcm_by_type(struct hda_codec *codec, int type)unsigned int i;for (i =0 ; i < spec->num_pins; i++) { -struct hda_pcm *pcm =get_pcm_rec (spec, i); +struct hda_pcm *pcm =get_pcm_rec (spec, i).pcm;if (pcm->pcm_type == type)return pcm;
Signature · 1 line
1.9.1
Re: [PATCH 2/4] ALSA: hda - add hdmi_pcm to manage hdmi pcm related features
Quoted 46 lines · On Thu, 31 Dec 2015 02:22:20 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
Use struct
hdmi_pcmwrapper for hdmi pcm management.
All PCM related features, like jack, will be put in this structure.Signed-off-by Libin Yang <[email protected]>--- sound/pci/hda/patch_hdmi.c | 44 ++++++++++++++++++++++++-------------------- 1 file changed, 24 insertions(+), 20 deletions(-)sound/pci/hda/patch_hdmi.c +7
-2@@ -86,7 +86,7 @@ struct hdmi_spec_per_pin {struct delayed_work work;struct snd_kcontrol *eld_ctl;struct snd_jack *acomp_jack;/* jack via audio component */ -struct hda_pcm *pcm;/* pointer to spec->pcm_rec[n] dynamically*/ +struct hdmi_pcm *pcm;/* pointer to spec->pcm_rec[n] dynamically*/ int pcm_idx;/* which pcm is attached. -1 means no pcm is attached */ int repoll_count;bool setup;/* the stream has been set up by prepare callback */ @@ -132,6 +132,11 @@ struct hdmi_ops {int (*chmap_validate)(int ca,int channels,unsigned char *chmap); }; +struct hdmi_pcm { +struct hda_pcm *pcm; +struct snd_jack *jack; +}; +struct hdmi_spec {int num_cvts;struct snd_array cvts;/* struct hdmi_spec_per_cvt */ @@ -139,7 +144,7 @@ struct hdmi_spec {int num_pins;struct snd_array pins;/* struct hdmi_spec_per_pin */ -struct hda_pcm *pcm_rec[16 ]; +struct hdmi_pcm pcm_rec[16 ];struct mutex pcm_lock;/* pcm_bitmap means which pcms have been assigned to pins*/ unsigned long pcm_bitmap;
sound/pci/hda/patch_hdmi.c static int hinfo_to_pcm_index(struct hda_codec *codec, · line 411
Quoted 5 lines
sound/pci/hda/patch_hdmi.c +1
-1@@ -403,7 +408,7 @@ static int hinfo_to_pcm_index(struct hda_codec *codec,int pcm_idx;for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) -if (get_pcm_rec (spec, pcm_idx)->stream == hinfo) +if (get_pcm_rec (spec, pcm_idx).pcm->stream == hinfo)
I would change rather get_pcm_rec() itself to point to hda_pcm. For referencing to hdmi_pcm, we can introduce another macro, e.g. get_hdmi_pcm(spec, idx). For example:
/* obtain hdmi_pcm object assigned to idx */
#define get_hdmi_pcm(spec, idx) (&(spec)->pcm_rec[idx])
/* obtain hda_pcm object assigned to idx */
#define get_pcm_rec(spec, idx) get_hdmi_pcm(spec, idx)->pcm
Takashi
Re: [PATCH 2/4] ALSA: hda - add hdmi_pcm to manage hdmi pcm related features
Quoted 66 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, January 07, 2016 9:59 PM
To: [email protected]
Cc: [email protected]; Lin, Mengdong; Yang, Libin
Subject: Re: [alsa-devel] [PATCH 2/4] ALSA: hda - addhdmi_pcmto manage hdmi pcm related featuresQuoted 9 lines · On Thu, 31 Dec 2015 02:22:20 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
Use struct
hdmi_pcmwrapper for hdmi pcm management.
All PCM related features, like jack, will be put in this structure.Signed-off-by Libin Yang <[email protected]>--- sound/pci/hda/patch_hdmi.c | 44 ++++++++++++++++++++++++--------------------
Review
Quoted 3 lines
1 file changed, 24 insertions(+), 20 deletions(-)(quoted diff) +0
-0
b/sound/pci/hda/patch_hdmi.csound/pci/hda/patch_hdmi.c struct hdmi_spec_per_pin { · line 89
Quoted 8 lines
index 6d6dba4..5549ddf 100644
sound/pci/hda/patch_hdmi.c +0
-1@@ -86,7 +86,7 @@ struct hdmi_spec_per_pin {struct delayed_work work;struct snd_kcontrol *eld_ctl;struct snd_jack *acomp_jack;/* jack via audio component */ -struct hda_pcm *pcm;/* pointer to spec->pcm_rec[n] dynamically*/
sound/pci/hda/patch_hdmi.c struct hdmi_spec_per_pin { · line 89
Quoted 1 line
sound/pci/hda/patch_hdmi.c +1
-0+struct hdmi_pcm *pcm;/* pointer to spec->pcm_rec[n] dynamically*/
sound/pci/hda/patch_hdmi.c struct hdmi_spec_per_pin { · line 90
Quoted 1 line
sound/pci/hda/patch_hdmi.c +0
-0int pcm_idx;/* which pcm is attached. -1 means no pcm is attached */
sound/pci/hda/patch_hdmi.c struct hdmi_ops { · line 132
Quoted 4 lines
sound/pci/hda/patch_hdmi.c +0
-0int repoll_count;bool setup;/* the stream has been set up by prepare callback */ @@ -132,6 +132,11 @@ struct hdmi_ops { int (*chmap_validate)(int ca, int channels, unsigned char*chmap);
sound/pci/hda/patch_hdmi.c static int hinfo_to_pcm_index(struct
Quoted 20 lines
sound/pci/hda/patch_hdmi.c +6
-1}; +struct hdmi_pcm { +struct hda_pcm *pcm; +struct snd_jack *jack; +}; +struct hdmi_spec {int num_cvts;struct snd_array cvts;/* struct hdmi_spec_per_cvt */ @@ -139,7 +144,7 @@ struct hdmi_spec {int num_pins;struct snd_array pins;/* struct hdmi_spec_per_pin */ -struct hda_pcm *pcm_rec[16 ]; +struct hdmi_pcm pcm_rec[16 ];struct mutex pcm_lock;/* pcm_bitmap means which pcms have been assigned to pins*/ unsigned long pcm_bitmap;@@ -403,7 +408,7 @@ static int hinfo_to_pcm_index(struct
hda_codec*codec,Quoted 2 lines
sound/pci/hda/patch_hdmi.c +0
-0int pcm_idx;
Quoted 7 lines
sound/pci/hda/patch_hdmi.c static int hinfo_to_pcm_index(struct hda_codec *codec, · line 411
Quoted 3 lines
sound/pci/hda/patch_hdmi.c +1
-1for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) -if (get_pcm_rec (spec, pcm_idx)->stream == hinfo) +if (get_pcm_rec (spec, pcm_idx).pcm->stream == hinfo)I would change rather
get_pcm_rec()itself to point tohda_pcm. For referencing tohdmi_pcm, we can introduce another macro, e.g.get_hdmi_pcm(spec, idx). For example:
Get it. It makes sense for compatibility. I will change it.
Quoted 9 lines
/* obtain
hdmi_pcmobject assigned to idx */
#defineget_hdmi_pcm(spec, idx)(&(spec)->pcm_rec[idx])/* obtain
hda_pcmobject assigned to idx */
#defineget_pcm_rec(spec, idx)get_hdmi_pcm(spec, idx)->pcmTakashi
PATCH 3/4 ALSA: hda - hdmi jack created based on pcm
In reply to [email protected]From: Libin Yang <[email protected]>
Jack is created based on pcm.
For dyn_pcm_assign:
Driver will not use hda_jack. It will operate snd_jack directly. snd_jack pointer will be stored in spec->pcm.jack. When pcm is assigned to pin, jack will be assigned to pin automatically.
For !dyn_pcm_assign:
Driver will continue using hda_jack for less impact on the old cases. Pcm is statically assigned to pin. So is jack. spec->pcm.jack will save the snd_jack pointer created in hda_jack.
--- sound/pci/hda/patch_hdmi.c | 96 ++++++++++++++++++++++++++++++++-------------- 1 file changed, 67 insertions(+), 29 deletions(-)
sound/pci/hda/patch_hdmi.c +67 -29
@@ -85,7 +85,6 @@ struct hdmi_spec_per_pin {struct mutex lock;struct delayed_work work;struct snd_kcontrol *eld_ctl; -struct snd_jack *acomp_jack;/* jack via audio component */ struct hdmi_pcm *pcm;/* pointer to spec->pcm_rec[n] dynamically*/ int pcm_idx;/* which pcm is attached. -1 means no pcm is attached */ int repoll_count;
@@ -1943,6 +1942,7 @@ static void sync_eld_via_acomp(struct hda_codec *codec, {struct hdmi_spec *spec = codec->spec;struct hdmi_eld *eld = &spec->temp_eld; +struct snd_jack *jack =NULL ;int size;mutex_lock (&per_pin->lock);
@@ -1966,8 +1966,18 @@ static void sync_eld_via_acomp(struct hda_codec *codec, eld->eld_size =0 ; } +/* pcm_idx >=0 before update_eld() means it is in monitor +* disconnected event. Jack must be fetched before update_eld() +* Get jack before update_eld() +*/ +if (per_pin->pcm_idx >=0 ) + jack = spec->pcm_rec[per_pin->pcm_idx].jack;update_eld (codec, per_pin, eld); -snd_jack_report (per_pin->acomp_jack, +if (jack ==NULL && per_pin->pcm_idx >=0 ) + jack = spec->pcm_rec[per_pin->pcm_idx].jack; +if (jack ==NULL ) + goto unlock; +snd_jack_report (jack, eld->monitor_present ?SND_JACK_AVOUT :0 ); unlock:mutex_unlock (&per_pin->lock);
@@ -2471,15 +2481,16 @@ static int generic_hdmi_build_pcms(struct hda_codec *codec)return 0 ; } -static void free_acomp_jack_priv (struct snd_jack *jack) +static void free_hdmi_jack_priv (struct snd_jack *jack) { -struct hdmi_spec_per_pin *per_pin = jack->private_data; +struct hdmi_pcm *pcm = jack->private_data; - per_pin->acomp_jack =NULL ; + pcm->jack =NULL ; } -static int add_acomp_jack_kctl (struct hda_codec *codec, -struct hdmi_spec_per_pin *per_pin, +static int add_hdmi_jack_kctl (struct hda_codec *codec, +struct hdmi_spec *spec, +int pcm_idx,const char *name) {struct snd_jack *jack;
@@ -2489,45 +2500,67 @@ static int add_acomp_jack_kctl(struct hda_codec *codec, true, false);if (err <0 )return err; - per_pin->acomp_jack = jack; - jack->private_data = per_pin; - jack->private_free = free_acomp_jack_priv; + + spec->pcm_rec[pcm_idx].jack = jack; + jack->private_data = &spec->pcm_rec[pcm_idx]; + jack->private_free = free_hdmi_jack_priv;return 0 ; } -static int generic_hdmi_build_jack (struct hda_codec *codec,int pin_idx) +static int generic_hdmi_build_jack (struct hda_codec *codec,int pcm_idx) {char hdmi_str[32 ] ="HDMI/DP" ;struct hdmi_spec *spec = codec->spec; -struct hdmi_spec_per_pin *per_pin =get_pin (spec, pin_idx); -int pcmdev =get_pcm_rec (spec, pin_idx).pcm->device; +struct hdmi_spec_per_pin *per_pin; +struct hda_jack_tbl *jack; +int pcmdev =get_pcm_rec (spec, pcm_idx).pcm->device;bool phantom_jack; +int ret;if (pcmdev >0 )sprintf (hdmi_str +strlen (hdmi_str),",pcm=%d" , pcmdev); -if (codec_has_acomp (codec)) -return add_acomp_jack_kctl (codec, per_pin, hdmi_str); - phantom_jack = !is_jack_detectable (codec, per_pin->pin_nid); -if (phantom_jack) -strncat (hdmi_str," Phantom" , -sizeof (hdmi_str) -strlen (hdmi_str) -1 ); -return snd_hda_jack_add_kctl (codec, per_pin->pin_nid, hdmi_str, - phantom_jack); +/* for !dyn_pcm_assign, we still use hda_jack for compatibility */ +if (!spec->dyn_pcm_assign) { +/* if not dyn_pcm_assign, it must be non-MST mode. +* This means pcms and pins are statically mapped. +* And pcm_idx is pin_idx. +*/ + per_pin =get_pin (spec, pcm_idx); + phantom_jack = !is_jack_detectable (codec, per_pin->pin_nid); +if (phantom_jack) +strncat (hdmi_str," Phantom" , +sizeof (hdmi_str) -strlen (hdmi_str) -1 ); + ret =snd_hda_jack_add_kctl (codec, per_pin->pin_nid, hdmi_str, + phantom_jack); +if (ret <0 ) +return ret; + jack =snd_hda_jack_tbl_get (codec, per_pin->pin_nid); +if (jack ==NULL ) +return 0 ; +/* statically bind jack */ + spec->pcm_rec[pcm_idx].jack = jack->jack; +return 0 ; + } + +return add_hdmi_jack_kctl (codec, spec, pcm_idx, hdmi_str); }static int generic_hdmi_build_controls (struct hda_codec *codec) {struct hdmi_spec *spec = codec->spec;int err; -int pin_idx; +int pin_idx, pcm_idx; -for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) { -struct hdmi_spec_per_pin *per_pin =get_pin (spec, pin_idx); - err =generic_hdmi_build_jack (codec, pin_idx); +for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) { + err =generic_hdmi_build_jack (codec, pcm_idx);if (err <0 )return err; + } + +for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) { +struct hdmi_spec_per_pin *per_pin =get_pin (spec, pin_idx); err = snd_hda_create_dig_out_ctls(codec, per_pin->pin_nid,
@@ -2626,18 +2659,23 @@ static void hdmi_array_free(struct hdmi_spec *spec)static void generic_hdmi_free (struct hda_codec *codec) {struct hdmi_spec *spec = codec->spec; -int pin_idx; +int pin_idx, pcm_idx;if (codec_has_acomp (codec))snd_hdac_i915_register_notifier (NULL );for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) {struct hdmi_spec_per_pin *per_pin =get_pin (spec, pin_idx); -cancel_delayed_work_sync (&per_pin->work);eld_proc_free (per_pin); -if (per_pin->acomp_jack) -snd_device_free (codec->card, per_pin->acomp_jack); + } + +for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) { +if (spec->dyn_pcm_assign) +snd_device_free (codec->card, + spec->pcm_rec[pcm_idx].jack); +else + spec->pcm_rec[pcm_idx].jack =NULL ; }if (spec->i915_bound)
Signature · 1 line
1.9.1
Re: [PATCH 3/4] ALSA: hda - hdmi jack created based on pcm
Quoted 7 lines · On Thu, 31 Dec 2015 02:22:21 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
Jack is created based on pcm.
For
dyn_pcm_assign:
Driver will not usehda_jack. It will operatesnd_jackdirectly.
This is nothing new, it's already so for Intel codecs (via audio component).
Quoted 1 line
snd_jackpointer will be stored inspec->pcm.jack.
.... instead of the current spec->acomp_jack.
Quoted 9 lines
When pcm is
assigned to pin, jack will be assigned to pin automatically.For !dyn_pcm_assign:
Driver will continue usinghda_jackfor less impact on the old cases. Pcm is statically assigned to pin. So is jack.spec->pcm.jackwill save thesnd_jackpointer created inhda_jack.Signed-off-by Libin Yang <[email protected]>
(snip)
Quoted 16 lines
sound/pci/hda/patch_hdmi.c +5
-4-static int generic_hdmi_build_jack (struct hda_codec *codec,int pin_idx) +static int generic_hdmi_build_jack (struct hda_codec *codec,int pcm_idx) {char hdmi_str[32 ] ="HDMI/DP" ;struct hdmi_spec *spec = codec->spec; -struct hdmi_spec_per_pin *per_pin =get_pin (spec, pin_idx); -int pcmdev =get_pcm_rec (spec, pin_idx).pcm->device; +struct hdmi_spec_per_pin *per_pin; +struct hda_jack_tbl *jack; +int pcmdev =get_pcm_rec (spec, pcm_idx).pcm->device;bool phantom_jack; +int ret;if (pcmdev >0 )sprintf (hdmi_str +strlen (hdmi_str),",pcm=%d" , pcmdev); -if (codec_has_acomp (codec))
sound/pci/hda/patch_hdmi.c static int add_acomp_jack_kctl(struct hda_codec *codec, · line 2524
Quoted 10 lines
sound/pci/hda/patch_hdmi.c +2
-7-return add_acomp_jack_kctl (codec, per_pin, hdmi_str); - phantom_jack = !is_jack_detectable (codec, per_pin->pin_nid); -if (phantom_jack) -strncat (hdmi_str," Phantom" , -sizeof (hdmi_str) -strlen (hdmi_str) -1 ); -return snd_hda_jack_add_kctl (codec, per_pin->pin_nid, hdmi_str, - phantom_jack); +/* for !dyn_pcm_assign, we still use hda_jack for compatibility */ +if (!spec->dyn_pcm_assign) {
Actually, the code changes become smaller with the following:
if (spec->dyn_pcm_assign) return add_hdmi_jack_kctl(codec, spec, pcm_idx, hdmi_str);
Then the rest is almost same as the original code, and you'd need to give a few more comments and assignment of pcm_rec[].jack in addition.
Quoted 15 lines
sound/pci/hda/patch_hdmi.c +1
-2@@ -2626,18 +2659,23 @@ static void hdmi_array_free(struct hdmi_spec *spec)static void generic_hdmi_free (struct hda_codec *codec) {struct hdmi_spec *spec = codec->spec; -int pin_idx; +int pin_idx, pcm_idx;if (codec_has_acomp (codec))snd_hdac_i915_register_notifier (NULL );for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) {struct hdmi_spec_per_pin *per_pin =get_pin (spec, pin_idx); -cancel_delayed_work_sync (&per_pin->work);eld_proc_free (per_pin);
sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec) · line 2678
Quoted 10 lines
sound/pci/hda/patch_hdmi.c +8
-2-if (per_pin->acomp_jack) -snd_device_free (codec->card, per_pin->acomp_jack); + } + +for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) { +if (spec->dyn_pcm_assign) +snd_device_free (codec->card, + spec->pcm_rec[pcm_idx].jack); +else + spec->pcm_rec[pcm_idx].jack =NULL ;
Check whether spec->pcm_rec[pcm_idx].jack is NULL beforehand.
Takashi
Re: [PATCH 3/4] ALSA: hda - hdmi jack created based on pcm
Quoted 15 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, January 07, 2016 10:14 PM
To: [email protected]
Cc: [email protected]; Lin, Mengdong; Yang, Libin
Subject: Re: [alsa-devel] [PATCH 3/4] ALSA: hda - hdmi jack created based on pcmQuoted 3 lines · On Thu, 31 Dec 2015 02:22:21 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
Quoted 7 lines
Quoted 4 lines
Jack is created based on pcm.
For
dyn_pcm_assign:
Driver will not usehda_jack. It will operatesnd_jackdirectly.This is nothing new, it's already so for Intel codecs (via audio component).
Yes. And I'm try to use this new method to all codecs as an option. :)
Quoted 50 lines
Quoted 2 lines
snd_jackpointer will be stored inspec->pcm.jack..... instead of the current
spec->acomp_jack.Quoted 9 lines
When pcm is
assigned to pin, jack will be assigned to pin automatically.For !dyn_pcm_assign:
Driver will continue usinghda_jackfor less impact on the old cases. Pcm is statically assigned to pin. So is jack.spec->pcm.jackwill save thesnd_jackpointer created inhda_jack.Signed-off-by Libin Yang <[email protected]>(snip)
Quoted 1 line
-static int generic_hdmi_build_jack(struct
hda_codec*codec, int
pin_idx)Quoted 1 line
+static int generic_hdmi_build_jack(struct
hda_codec*codec, int
pcm_idx)sound/pci/hda/patch_hdmi.c static int add_acomp_jack_kctl(struct hda_codec *codec,
Quoted 13 lines
{
sound/pci/hda/patch_hdmi.c +4
-2char hdmi_str[32 ] ="HDMI/DP" ;struct hdmi_spec *spec = codec->spec; -struct hdmi_spec_per_pin *per_pin =get_pin (spec, pin_idx); -int pcmdev =get_pcm_rec (spec, pin_idx).pcm->device; +struct hdmi_spec_per_pin *per_pin; +struct hda_jack_tbl *jack; +int pcmdev =get_pcm_rec (spec, pcm_idx).pcm->device;bool phantom_jack; +int ret;if (pcmdev >0 ) sprintf(hdmi_str + strlen(hdmi_str), ",pcm=%d",pcmdev);
sound/pci/hda/patch_hdmi.c static int add_acomp_jack_kctl(struct hda_codec *codec,
Quoted 8 lines
sound/pci/hda/patch_hdmi.c +0
-7-if (codec_has_acomp (codec)) -return add_acomp_jack_kctl (codec, per_pin, hdmi_str); - phantom_jack = !is_jack_detectable (codec, per_pin->pin_nid); -if (phantom_jack) -strncat (hdmi_str," Phantom" , -sizeof (hdmi_str) -strlen (hdmi_str) -1 ); - return snd_hda_jack_add_kctl(codec, per_pin->pin_nid,
hdmi_str,sound/pci/hda/patch_hdmi.c static int add_acomp_jack_kctl(struct hda_codec *codec, · line 2524
Quoted 3 lines
sound/pci/hda/patch_hdmi.c +2
-1- phantom_jack); +/* for !dyn_pcm_assign, we still use hda_jack for compatibility */ +if (!spec->dyn_pcm_assign) {Actually, the code changes become smaller with the following:
Quoted 3 lines
if (spec->dyn_pcm_assign) return add_hdmi_jack_kctl(codec, spec, pcm_idx,
hdmi_str);
OK, I will change it. Anyway, we need enable unsol_event here if !acomp.
Quoted 20 lines
Then the rest is almost same as the original code, and you'd need to give a few more comments and assignment of pcm_rec[].jack in addition.
Review static void hdmi_array_free(struct
Quoted 1 line
(quoted diff) +0
-0@@ -2626,18 +2659,23 @@ static void hdmi_array_free(struct
hdmi_spec*spec)sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec)
Quoted 11 lines
sound/pci/hda/patch_hdmi.c +1
-1static void generic_hdmi_free (struct hda_codec *codec) {struct hdmi_spec *spec = codec->spec; -int pin_idx; +int pin_idx, pcm_idx;if (codec_has_acomp (codec))snd_hdac_i915_register_notifier (NULL );for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) { struct hdmi_spec_per_pin *per_pin = get_pin(spec,
pin_idx);
Quoted 17 lines
Quoted 4 lines
sound/pci/hda/patch_hdmi.c +0
-2-cancel_delayed_work_sync (&per_pin->work);eld_proc_free (per_pin); -if (per_pin->acomp_jack)sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec) · line 2678
Quoted 10 lines
sound/pci/hda/patch_hdmi.c +8
-1-snd_device_free (codec->card, per_pin- acomp_jack); + } + +for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) { +if (spec->dyn_pcm_assign) +snd_device_free (codec->card, + spec->pcm_rec[pcm_idx].jack); +else + spec->pcm_rec[pcm_idx].jack =NULL ;Check whether spec->pcm_rec[pcm_idx].jack is NULL beforehand.
Do you mean:
if (spec->pcm_rec[pcm_idx].jack)
spec->pcm_rec[pcm_idx].jack = NULL;
Regards,
Libin
Quoted 2 lines
Takashi
Re: [PATCH 3/4] ALSA: hda - hdmi jack created based on pcm
Quoted 32 lines · Libin
Quoted 14 lines
Review static void hdmi_array_free(struct
Quoted 1 line
(quoted diff) +0
-0@@ -2626,18 +2659,23 @@ static void hdmi_array_free(struct
hdmi_spec*spec)sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec)
Quoted 11 lines
sound/pci/hda/patch_hdmi.c +1
-1static void generic_hdmi_free (struct hda_codec *codec) {struct hdmi_spec *spec = codec->spec; -int pin_idx; +int pin_idx, pcm_idx;if (codec_has_acomp (codec))snd_hdac_i915_register_notifier (NULL );for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) { struct hdmi_spec_per_pin *per_pin = get_pin(spec,
pin_idx);Quoted 17 lines
Quoted 4 lines
sound/pci/hda/patch_hdmi.c +0
-2-cancel_delayed_work_sync (&per_pin->work);eld_proc_free (per_pin); -if (per_pin->acomp_jack)sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec) · line 2678
Quoted 10 lines
sound/pci/hda/patch_hdmi.c +8
-1-snd_device_free (codec->card, per_pin- acomp_jack); + } + +for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) { +if (spec->dyn_pcm_assign) +snd_device_free (codec->card, + spec->pcm_rec[pcm_idx].jack); +else + spec->pcm_rec[pcm_idx].jack =NULL ;Check whether spec->pcm_rec[pcm_idx].jack is NULL beforehand.
Quoted 3 lines
Do you mean:
if (spec->pcm_rec[pcm_idx].jack)spec->pcm_rec[pcm_idx].jack = NULL;
Not only that. Calling snd_device_free() with NULL isn't allowed.
Takashi
Re: [PATCH 3/4] ALSA: hda - hdmi jack created based on pcm
Quoted 44 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Friday, January 08, 2016 3:44 PM
To: Yang, Libin
Cc: [email protected]; [email protected]; Lin, Mengdong
Subject: Re: [alsa-devel] [PATCH 3/4] ALSA: hda - hdmi jack created based on pcmQuoted 32 lines · Libin
Quoted 31 lines
Review static void hdmi_array_free(struct
Quoted 1 line
(quoted diff) +0
-0@@ -2626,18 +2659,23 @@ static void hdmi_array_free(struct
hdmi_spec*spec)sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec)
Quoted 11 lines
sound/pci/hda/patch_hdmi.c +1
-1static void generic_hdmi_free (struct hda_codec *codec) {struct hdmi_spec *spec = codec->spec; -int pin_idx; +int pin_idx, pcm_idx;if (codec_has_acomp (codec))snd_hdac_i915_register_notifier (NULL );for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) { struct hdmi_spec_per_pin *per_pin = get_pin(spec,
pin_idx);Quoted 4 lines
sound/pci/hda/patch_hdmi.c +0
-2-cancel_delayed_work_sync (&per_pin->work);eld_proc_free (per_pin); -if (per_pin->acomp_jack)sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec) · line 2678
Quoted 10 lines
sound/pci/hda/patch_hdmi.c +8
-1-snd_device_free (codec->card, per_pin- acomp_jack); + } + +for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) { +if (spec->dyn_pcm_assign) +snd_device_free (codec->card, + spec->pcm_rec[pcm_idx].jack); +else + spec->pcm_rec[pcm_idx].jack =NULL ;Check whether spec->pcm_rec[pcm_idx].jack is NULL beforehand.
Quoted 5 lines
Quoted 3 lines
Do you mean:
if (spec->pcm_rec[pcm_idx].jack)spec->pcm_rec[pcm_idx].jack = NULL;Not only that. Calling
snd_device_free()with NULL isn't allowed.
I see. It will be:
+for (pcm_idx = 0; pcm_idx < spec->pcm_used; pcm_idx++) {
+ if (spec->pcm_rec[pcm_idx].jack == NULL)
+ continue;
+ if (spec->dyn_pcm_assign)
BTW: It seems snd_device_free() will check the pointer.
Regards,
Libin
Quoted 1 line
Takashi
Re: [PATCH 3/4] ALSA: hda - hdmi jack created based on pcm
Quoted 57 lines · Libin
Quoted 45 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Friday, January 08, 2016 3:44 PM
To: Yang, Libin
Cc: [email protected]; [email protected]; Lin, Mengdong
Subject: Re: [alsa-devel] [PATCH 3/4] ALSA: hda - hdmi jack created based on pcmQuoted 32 lines · Libin
Quoted 31 lines
Review static void hdmi_array_free(struct
Quoted 1 line
(quoted diff) +0
-0@@ -2626,18 +2659,23 @@ static void hdmi_array_free(struct
hdmi_spec*spec)sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec)
Quoted 11 lines
sound/pci/hda/patch_hdmi.c +1
-1static void generic_hdmi_free (struct hda_codec *codec) {struct hdmi_spec *spec = codec->spec; -int pin_idx; +int pin_idx, pcm_idx;if (codec_has_acomp (codec))snd_hdac_i915_register_notifier (NULL );for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) { struct hdmi_spec_per_pin *per_pin = get_pin(spec,
pin_idx);Quoted 4 lines
sound/pci/hda/patch_hdmi.c +0
-2-cancel_delayed_work_sync (&per_pin->work);eld_proc_free (per_pin); -if (per_pin->acomp_jack)sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec) · line 2678
Quoted 10 lines
sound/pci/hda/patch_hdmi.c +8
-1-snd_device_free (codec->card, per_pin- acomp_jack); + } + +for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) { +if (spec->dyn_pcm_assign) +snd_device_free (codec->card, + spec->pcm_rec[pcm_idx].jack); +else + spec->pcm_rec[pcm_idx].jack =NULL ;Check whether spec->pcm_rec[pcm_idx].jack is NULL beforehand.
Quoted 5 lines
Quoted 3 lines
Do you mean:
if (spec->pcm_rec[pcm_idx].jack)spec->pcm_rec[pcm_idx].jack = NULL;Not only that. Calling
snd_device_free()with NULL isn't allowed.I see. It will be:
sound/pci/hda/patch_hdmi.c +4
-0+for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) { +if (spec->pcm_rec[pcm_idx].jack ==NULL ) +continue ; +if (spec->dyn_pcm_assign)
Quoted 1 line
BTW: It seems
snd_device_free()will check the pointer.
Yes but with snd_BUG_ON(), i.e. with a warning. It shouldn't be called with NULL.
Takashi
Re: [PATCH 3/4] ALSA: hda - hdmi jack created based on pcm
Quoted 73 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Friday, January 08, 2016 3:55 PM
To: Yang, Libin
Cc: [email protected]; [email protected]; Lin, Mengdong
Subject: Re: [alsa-devel] [PATCH 3/4] ALSA: hda - hdmi jack created based on pcmQuoted 9 lines · Libin
Quoted 9 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Friday, January 08, 2016 3:44 PM
To: Yang, Libin
Cc: [email protected]; [email protected]; Lin, Mengdong
Subject: Re: [alsa-devel] [PATCH 3/4] ALSA: hda - hdmi jack createdbased
Quoted 12 lines
Quoted 12 lines
on pcm
Quoted 8 lines · Libin
Quoted 8 lines
Review static void hdmi_array_free(struct
Quoted 1 line
(quoted diff) +0
-0@@ -2626,18 +2659,23 @@ static void hdmi_array_free(struct
hdmi_spec*spec)Quoted 6 lines
sound/pci/hda/patch_hdmi.c +1
-1static void generic_hdmi_free (struct hda_codec *codec) {struct hdmi_spec *spec = codec->spec; -int pin_idx; +int pin_idx, pcm_idx;Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec)
Quoted 5 lines
sound/pci/hda/patch_hdmi.c +0
-0if (codec_has_acomp (codec))snd_hdac_i915_register_notifier (NULL );for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) { struct hdmi_spec_per_pin *per_pin =get_pin(spec,
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
pin_idx);sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec)
Quoted 9 lines
sound/pci/hda/patch_hdmi.c +3
-3-cancel_delayed_work_sync (&per_pin->work);eld_proc_free (per_pin); -if (per_pin->acomp_jack) -snd_device_free (codec->card, per_pin- acomp_jack); + } + + for (pcm_idx = 0; pcm_idx < spec->pcm_used;pcm_idx++) {
Quoted 22 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec)
Quoted 3 lines
sound/pci/hda/patch_hdmi.c +3
-0+if (spec->dyn_pcm_assign) + snd_device_free(codec->card, + spec-pcm_rec[pcm_idx].jack);
Quoted 11 lines
Quoted 9 lines
Quoted 5 lines
sound/pci/hda/patch_hdmi.c static void hdmi_array_free(struct hdmi_spec *spec) · line 2678
Quoted 2 lines
sound/pci/hda/patch_hdmi.c +2
-0+else + spec->pcm_rec[pcm_idx].jack =NULL ;Check whether spec->pcm_rec[pcm_idx].jack is NULL beforehand.
Do you mean:
if (spec->pcm_rec[pcm_idx].jack)spec->pcm_rec[pcm_idx].jack = NULL;Not only that. Calling
snd_device_free()with NULL isn't allowed.I see. It will be:
sound/pci/hda/patch_hdmi.c +4
-0+for (pcm_idx =0 ; pcm_idx < spec->pcm_used; pcm_idx++) { +if (spec->pcm_rec[pcm_idx].jack ==NULL ) +continue ; +if (spec->dyn_pcm_assign)
Quoted 4 lines
Quoted 1 line
BTW: It seems
snd_device_free()will check the pointer.Yes but with
snd_BUG_ON(), i.e. with a warning. It shouldn't be called with NULL.
Get it :-)
Regards,
Libin
Quoted 3 lines
Takashi
PATCH 4/4 ALSA: hda - hdmi monitor hotplug support for dynamic pcm assignment
In reply to [email protected]From: Libin Yang <[email protected]>
This patch adds the support for monitor hotplug of dynamic pcm assignment.
1. unsol_event enabling
- For codec_has_acomp, unsol_event is disabled.
- For !codec_has_acomp && !dyn_pcm_assign, use the hda_jack helper to enable unsol_event
- For !codec_has_acomp && dyn_pcm_assign, enable unsol_event with verb directly
2. unsol_event handling
- For !dyn_pcm_assign, use hda_jack helper to report the event
- For dyn_pcm_assign, use snd_jack_report() directly
--- sound/pci/hda/patch_hdmi.c | 97 ++++++++++++++++++++++++++++++++++++++-------- 1 file changed, 81 insertions(+), 16 deletions(-)
sound/pci/hda/patch_hdmi.c +81 -16
@@ -87,6 +87,7 @@ struct hdmi_spec_per_pin {struct snd_kcontrol *eld_ctl;struct hdmi_pcm *pcm;/* pointer to spec->pcm_rec[n] dynamically*/ int pcm_idx;/* which pcm is attached. -1 means no pcm is attached */ +int unsol_tag;int repoll_count;bool setup;/* the stream has been set up by prepare callback */ int channels;/* current number of channels */
@@ -1229,23 +1230,44 @@ static void jack_callback(struct hda_codec *codec,check_presence_and_report (codec, jack->tbl->nid); } +static hda_nid_t hdmi_get_nid_from_tag (struct hda_codec *codec,int tag) +{ +int pin_idx; +struct hdmi_spec *spec = codec->spec; + +for (pin_idx =0 ; pin_idx < spec->num_pins; pin_idx++) { +struct hdmi_spec_per_pin *per_pin =get_pin (spec, pin_idx); + +if (per_pin->unsol_tag == tag) +return per_pin->pin_nid; + } +/* this will never happen, tag is checked before */ +return 0 ; +} +static void hdmi_intrinsic_event (struct hda_codec *codec,unsigned int res) {int tag = res >>AC_UNSOL_RES_TAG_SHIFT ;struct hda_jack_tbl *jack; +struct hdmi_spec *spec = codec->spec;int dev_entry = (res &AC_UNSOL_RES_DE ) >>AC_UNSOL_RES_DE_SHIFT ; +hda_nid_t nid; - jack =snd_hda_jack_tbl_get_from_tag (codec, tag); -if (!jack) -return ; - jack->jack_dirty =1 ; +if (!spec->dyn_pcm_assign) { + jack =snd_hda_jack_tbl_get_from_tag (codec, tag); +if (!jack) +return ; + jack->jack_dirty =1 ; + nid = jack->nid; + }else + nid =hdmi_get_nid_from_tag (codec, tag);codec_dbg (codec,"HDMI hot plug event: Codec=%d Pin=%d Device=%d Inactive=%d Presence_Detect=%d ELD_Valid=%d\n" , - codec->addr, jack->nid, dev_entry, !!(res &AC_UNSOL_RES_IA ), + codec->addr, nid, dev_entry, !!(res &AC_UNSOL_RES_IA ), !!(res &AC_UNSOL_RES_PD ), !!(res &AC_UNSOL_RES_ELDV )); -check_presence_and_report (codec, jack->nid); +check_presence_and_report (codec, nid); }static void hdmi_non_intrinsic_event (struct hda_codec *codec,unsigned int res)
@@ -1270,13 +1292,30 @@ static void hdmi_non_intrinsic_event(struct hda_codec *codec, unsigned int res) ; } +static bool hdmi_unsol_tag_is_valid (struct hda_codec *codec,int tag) +{ +struct hdmi_spec *spec = codec->spec; +int i; + +if (!spec->dyn_pcm_assign) { +if (snd_hda_jack_tbl_get_from_tag (codec, tag)) +return true; + }else { +for (i =0 ; i < spec->num_pins; i++) { +if (get_pin (spec, i)->unsol_tag == tag) +return true; + } + } + +return false; +}static void hdmi_unsol_event (struct hda_codec *codec,unsigned int res) {int tag = res >>AC_UNSOL_RES_TAG_SHIFT ;int subtag = (res &AC_UNSOL_RES_SUBTAG ) >>AC_UNSOL_RES_SUBTAG_SHIFT ; -if (!snd_hda_jack_tbl_get_from_tag (codec, tag)) { +if (!hdmi_unsol_tag_is_valid (codec, tag)) {codec_dbg (codec,"Unexpected HDMI event tag 0x%x\n" , tag);return ; }
@@ -1875,7 +1914,8 @@ static void update_eld(struct hda_codec *codec,static bool hdmi_present_sense_via_verbs (struct hdmi_spec_per_pin *per_pin,int repoll) { -struct hda_jack_tbl *jack; +struct hda_jack_tbl *jack =NULL ; +struct snd_jack *sjack =NULL ;struct hda_codec *codec = per_pin->codec;struct hdmi_spec *spec = codec->spec;struct hdmi_eld *eld = &spec->temp_eld;
@@ -1890,7 +1930,7 @@ static bool hdmi_present_sense_via_verbs(struct hdmi_spec_per_pin *per_pin,* the unsolicited response to avoid custom WARs. */ int present; -bool ret; +bool ret = false;bool do_repoll = false;snd_hda_power_up_pm (codec);
@@ -1920,14 +1960,26 @@ static bool hdmi_present_sense_via_verbs(struct hdmi_spec_per_pin *per_pin, do_repoll = true; } +if (spec->dyn_pcm_assign && per_pin->pcm_idx >=0 ) { + sjack = spec->pcm_rec[per_pin->pcm_idx].jack; +snd_jack_report (sjack, + pin_eld->monitor_present ?SND_JACK_AVOUT :0 ); + } +if (do_repoll)schedule_delayed_work (&per_pin->work,msecs_to_jiffies (300 ));else update_eld (codec, per_pin, eld); - ret = !repoll || !pin_eld->monitor_present || pin_eld->eld_valid; - - jack =snd_hda_jack_tbl_get (codec, pin_nid); +if (!spec->dyn_pcm_assign) { + ret = !repoll || !pin_eld->monitor_present || + pin_eld->eld_valid; + jack =snd_hda_jack_tbl_get (codec, pin_nid); + }else if (per_pin->pcm_idx >=0 && !sjack) { + sjack = spec->pcm_rec[per_pin->pcm_idx].jack; +snd_jack_report (sjack, + pin_eld->monitor_present ?SND_JACK_AVOUT :0 ); + }if (jack) jack->block_report = !ret;
@@ -2511,7 +2563,7 @@ static int generic_hdmi_build_jack(struct hda_codec *codec, int pcm_idx) {char hdmi_str[32 ] ="HDMI/DP" ;struct hdmi_spec *spec = codec->spec; -struct hdmi_spec_per_pin *per_pin; +struct hdmi_spec_per_pin *per_pin =get_pin (spec, pcm_idx);struct hda_jack_tbl *jack;int pcmdev =get_pcm_rec (spec, pcm_idx).pcm->device;bool phantom_jack;
@@ -2526,7 +2578,7 @@ static int generic_hdmi_build_jack(struct hda_codec *codec, int pcm_idx)* This means pcms and pins are statically mapped. * And pcm_idx is pin_idx. */ - per_pin =get_pin (spec, pcm_idx); + phantom_jack = !is_jack_detectable (codec, per_pin->pin_nid);if (phantom_jack) strncat(hdmi_str, " Phantom",
@@ -2540,10 +2592,17 @@ static int generic_hdmi_build_jack(struct hda_codec *codec, int pcm_idx)return 0 ;/* statically bind jack */ spec->pcm_rec[pcm_idx].jack = jack->jack; + per_pin->unsol_tag = jack->tag;return 0 ; } -return add_hdmi_jack_kctl (codec, spec, pcm_idx, hdmi_str); + per_pin->unsol_tag = per_pin->pin_nid_idx +1 ; + ret =add_hdmi_jack_kctl (codec, spec, pcm_idx, hdmi_str); +if (!codec_has_acomp (codec)) +snd_hda_codec_write_cache (codec, per_pin->pin_nid,0 , +AC_VERB_SET_UNSOLICITED_ENABLE , +AC_USRSP_EN | per_pin->unsol_tag); +return ret; }static int generic_hdmi_build_controls (struct hda_codec *codec)
@@ -2636,7 +2695,13 @@ static int generic_hdmi_init(struct hda_codec *codec)hda_nid_t pin_nid = per_pin->pin_nid;hdmi_init_pin (codec, pin_nid); -if (!codec_has_acomp (codec)) +/* if codec_has_acomp, will not enable unsol event +* if !codec_has_acomp && ! dyn_pcm_assign, +* will use hda_jack +* if !codec_has_acomp && dyn_pcm_assign, +* enable unsol_event when building jack +*/ +if (!codec_has_acomp (codec) && !spec->dyn_pcm_assign)snd_hda_jack_detect_enable_callback (codec, pin_nid, codec->jackpoll_interval >0 ? jack_callback :NULL );
Signature · 1 line
1.9.1
Re: [PATCH 4/4] ALSA: hda - hdmi monitor hotplug support for dynamic pcm assignment
Quoted 12 lines · On Thu, 31 Dec 2015 02:22:22 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
This patch adds the support for monitor hotplug of dynamic pcm assignment.
1.
unsol_eventenabling
- Forcodec_has_acomp,unsol_eventis disabled.
- For !codec_has_acomp && !dyn_pcm_assign, use thehda_jackhelper to enableunsol_event
- For !codec_has_acomp &&dyn_pcm_assign, enableunsol_eventwith verb directly
Quoted 3 lines
2.
unsol_eventhandling
- For !dyn_pcm_assign, usehda_jackhelper to report the event
- Fordyn_pcm_assign, usesnd_jack_report()directly
I guess we can reduce lots of codes if ignoring the case with dyn_pcm_assign but without audio component? If so, for simplicity, we can limit dyn_pcm_assign only tied with audio component. Just add a WARN_ON() in such a case. Although the functionality is somehow unrelated, the actual testing and coding is more targeted with Intel chips that are only with audio component.
Takashi
Re: [PATCH 4/4] ALSA: hda - hdmi monitor hotplug support for dynamic pcm assignment
Hi Takashi,
Quoted 29 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, January 07, 2016 10:18 PM
To: [email protected]
Cc: [email protected]; Lin, Mengdong; Yang, Libin
Subject: Re: [alsa-devel] [PATCH 4/4] ALSA: hda - hdmi monitor hotplug support for dynamic pcm assignmentQuoted 4 lines · On Thu, 31 Dec 2015 02:22:22 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
This patch adds the support for monitor hotplug of dynamic pcm
assignment.
Quoted 4 lines
1.
unsol_eventenabling
- Forcodec_has_acomp,unsol_eventis disabled.
- For !codec_has_acomp && !dyn_pcm_assign, use thehda_jackhelper to
Quoted 2 lines
enable
unsol_event
- For !codec_has_acomp &&dyn_pcm_assign, enableunsol_eventwith verb
Quoted 5 lines
directly
2.
unsol_eventhandling
- For !dyn_pcm_assign, usehda_jackhelper to report the event
- Fordyn_pcm_assign, usesnd_jack_report()directly
Quoted 6 lines
I guess we can reduce lots of codes if ignoring the case with
dyn_pcm_assignbut without audio component? If so, for simplicity, we can limitdyn_pcm_assignonly tied with audio component. Just add aWARN_ON()in such a case. Although the functionality is somehow unrelated, the actual testing and coding is more targeted with Intel chips that are only with audio component.
My initial idea is to support:
1. dyn_pcm_assign && acomp: Intel case
2. dyn_pcm_assign && !acomp: other vendors MST case
3. !dyn_pcm_assign && acomp: Intel non-mst case
4. !dyn_pcm_assign && !acomp: other vendors current case
Do you mean we can ignore other vendors' case so far? If so, the code will be simpler.
Quoted 3 lines
Takashi
Re: [PATCH 4/4] ALSA: hda - hdmi monitor hotplug support for dynamic pcm assignment
Quoted 39 lines · Libin
Hi Takashi,
Quoted 29 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, January 07, 2016 10:18 PM
To: [email protected]
Cc: [email protected]; Lin, Mengdong; Yang, Libin
Subject: Re: [alsa-devel] [PATCH 4/4] ALSA: hda - hdmi monitor hotplug support for dynamic pcm assignmentQuoted 4 lines · On Thu, 31 Dec 2015 02:22:22 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
This patch adds the support for monitor hotplug of dynamic pcm
assignment.
Quoted 4 lines
1.
unsol_eventenabling
- Forcodec_has_acomp,unsol_eventis disabled.
- For !codec_has_acomp && !dyn_pcm_assign, use thehda_jackhelper to
Quoted 2 lines
enable
unsol_event
- For !codec_has_acomp &&dyn_pcm_assign, enableunsol_eventwith verb
Quoted 5 lines
directly
2.
unsol_eventhandling
- For !dyn_pcm_assign, usehda_jackhelper to report the event
- Fordyn_pcm_assign, usesnd_jack_report()directlyQuoted 6 lines
I guess we can reduce lots of codes if ignoring the case with
dyn_pcm_assignbut without audio component? If so, for simplicity, we can limitdyn_pcm_assignonly tied with audio component. Just add aWARN_ON()in such a case. Although the functionality is somehow unrelated, the actual testing and coding is more targeted with Intel chips that are only with audio component.
Quoted 8 lines
My initial idea is to support:
1.dyn_pcm_assign&& acomp: Intel case
2.dyn_pcm_assign&& !acomp: other vendors MST case
3. !dyn_pcm_assign && acomp: Intel non-mst case
4. !dyn_pcm_assign && !acomp: other vendors current caseDo you mean we can ignore other vendors' case so far? If so, the code will be simpler.
Yes. And give WARN_ON(dyn_pcm_assign && !acomp);
Takashi
Re: [PATCH 4/4] ALSA: hda - hdmi monitor hotplug support for dynamic pcm assignment
Quoted 59 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Friday, January 08, 2016 3:45 PM
To: Yang, Libin
Cc: [email protected]; [email protected]; Lin, Mengdong
Subject: Re: [alsa-devel] [PATCH 4/4] ALSA: hda - hdmi monitor hotplug support for dynamic pcm assignmentQuoted 9 lines · Libin
Hi Takashi,
Quoted 6 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, January 07, 2016 10:18 PM
To: [email protected]
Cc: [email protected]; Lin, Mengdong; Yang, Libin
Subject: Re: [alsa-devel] [PATCH 4/4] ALSA: hda - hdmi monitorhotplug
Quoted 17 lines
Quoted 17 lines
support for dynamic pcm assignment
Quoted 4 lines · On Thu, 31 Dec 2015 02:22:22 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
This patch adds the support for monitor hotplug of dynamic pcm
assignment.
Quoted 4 lines
1.
unsol_eventenabling
- Forcodec_has_acomp,unsol_eventis disabled.
- For !codec_has_acomp && !dyn_pcm_assign, use thehda_jackhelper to
Quoted 2 lines
enable
unsol_event
- For !codec_has_acomp &&dyn_pcm_assign, enableunsol_eventwith verb
Quoted 8 lines
Quoted 8 lines
Quoted 5 lines
directly
2.
unsol_eventhandling
- For !dyn_pcm_assign, usehda_jackhelper to report the event
- Fordyn_pcm_assign, usesnd_jack_report()directlyI guess we can reduce lots of codes if ignoring the case with
dyn_pcm_assignbut without audio component? If so, for simplicity,we
Quoted 11 lines
Quoted 4 lines
can limit
dyn_pcm_assignonly tied with audio component. Just add aWARN_ON()in such a case. Although the functionality is somehow unrelated, the actual testing and coding is more targeted with Intel chips that are only with audio component.My initial idea is to support:
1.dyn_pcm_assign&& acomp: Intel case
2.dyn_pcm_assign&& !acomp: other vendors MST case
3. !dyn_pcm_assign && acomp: Intel non-mst case
4. !dyn_pcm_assign && !acomp: other vendors current case
Quoted 4 lines
Quoted 2 lines
Do you mean we can ignore other vendors' case so far? If so, the code will be simpler.
Yes. And give
WARN_ON(dyn_pcm_assign && !acomp);
Get it. I will follow it.
Regards,
Libin
Quoted 3 lines
Takashi
Quoted 4 lines · On Thu, 31 Dec 2015 02:22:18 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
The patchset adds hdmi jack support for dynamic pcm assignment
To which branch is this supposed to be applied?
thanks,
Takashi
Quoted 15 lines
Libin Yang (4):
ALSA: Add documentation about HD-audio DP MST
ALSA: hda - addhdmi_pcmto manage hdmi pcm related features
ALSA: hda - hdmi jack created based on pcm
ALSA: hda - hdmi monitor hotplug support for dynamic pcm assignmentDocumentation/sound/alsa/HD-Audio-DP-MST-audio.txt | 75 +++++++ sound/pci/hda/patch_hdmi.c | 229 +++++++++++++++------ 2 files changed, 243 insertions(+), 61 deletions(-) create mode 100644 Documentation/sound/alsa/HD-Audio-DP-MST-audio.txtSignature · 1 line
1.9.1
Hi Takashi,
Quoted 8 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Wednesday, January 06, 2016 5:18 PM
To: [email protected]
Cc: [email protected]; Lin, Mengdong; Yang, Libin
Subject: Re: [alsa-devel] [PATCH 0/4] ALSA: hda - hdmi jack support for dynamic pcm assignment
Quoted 8 lines
Quoted 4 lines · On Thu, 31 Dec 2015 02:22:18 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
The patchset adds hdmi jack support for dynamic pcm assignment
To which branch is this supposed to be applied?
This is preparation for DP MST audio. And it is for hdmi-jack branch.
Regards,
Libin
Quoted 25 lines
thanks,
Takashi
Quoted 6 lines
Libin Yang (4):
ALSA: Add documentation about HD-audio DP MST
ALSA: hda - addhdmi_pcmto manage hdmi pcm related features
ALSA: hda - hdmi jack created based on pcm
ALSA: hda - hdmi monitor hotplug support for dynamic pcmassignment
Quoted 2 lines
Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt | 75+++++++
Quoted 1 line
sound/pci/hda/patch_hdmi.c | 229 +++++++++++++++------
Quoted 2 lines
2 files changed, 243 insertions(+), 61 deletions(-) create mode 100644 Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt
Quoted 4 lines
--
1.9.1
Quoted 14 lines · Libin
Hi Takashi,
Quoted 11 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Wednesday, January 06, 2016 5:18 PM
To: [email protected]
Cc: [email protected]; Lin, Mengdong; Yang, Libin
Subject: Re: [alsa-devel] [PATCH 0/4] ALSA: hda - hdmi jack support for dynamic pcm assignmentQuoted 1 line · On Thu, 31 Dec 2015 02:22:18 +0100, [email protected] wrote:
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
From: Libin Yang <[email protected]>
The patchset adds hdmi jack support for dynamic pcm assignment
To which branch is this supposed to be applied?
This is preparation for DP MST audio. And it is for hdmi-jack branch.
Do you mean my test/hdmi-jack branch? So these are additional fixes on top of your former MST patches? If yes, it should go to topic/hda-mst branch instead.
test/hdmi-jack branch contains two unofficial patches in addition to your i915 MST patches that haven't been merged yet.
Takashi
Quoted 34 lines
Regards,
LibinQuoted 14 lines
thanks,
Takashi
Quoted 6 lines
Libin Yang (4):
ALSA: Add documentation about HD-audio DP MST
ALSA: hda - addhdmi_pcmto manage hdmi pcm related features
ALSA: hda - hdmi jack created based on pcm
ALSA: hda - hdmi monitor hotplug support for dynamic pcmassignment
Quoted 1 line
Quoted 11 lines
Quoted 1 line
Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt | 75+++++++
Quoted 1 line
sound/pci/hda/patch_hdmi.c | 229 +++++++++++++++------
Quoted 2 lines
2 files changed, 243 insertions(+), 61 deletions(-) create mode 100644 Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt
Quoted 4 lines
--
1.9.1_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 33 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Thursday, January 07, 2016 6:32 PM
To: Yang, Libin
Cc: [email protected]; Lin, Mengdong; alsa-devel@alsa- project.org
Subject: Re: [alsa-devel] [PATCH 0/4] ALSA: hda - hdmi jack support for dynamic pcm assignmentQuoted 9 lines · Libin
Hi Takashi,
Quoted 6 lines
-----Original Message-----
From: Takashi Iwai [mailto:[email protected]]
Sent: Wednesday, January 06, 2016 5:18 PM
To: [email protected]
Cc: [email protected]; Lin, Mengdong; Yang, Libin
Subject: Re: [alsa-devel] [PATCH 0/4] ALSA: hda - hdmi jack supportfor
Quoted 11 lines
Quoted 10 lines
dynamic pcm assignment
Quoted 4 lines · On Thu, 31 Dec 2015 02:22:18 +0100, [email protected] wrote:
From: Libin Yang <[email protected]>
The patchset adds hdmi jack support for dynamic pcm assignment
To which branch is this supposed to be applied?
Quoted 8 lines
Quoted 1 line
This is preparation for DP MST audio. And it is for hdmi-jack branch.
Do you mean my test/hdmi-jack branch? So these are additional fixes on top of your former MST patches? If yes, it should go to topic/hda-mst branch instead.
test/hdmi-jack branch contains two unofficial patches in addition to your i915 MST patches that haven't been merged yet.
Oh, I see. So it should go to topic/hda-mst branch. Thanks.
Regards,
Libin
Quoted 40 lines
Takashi
Quoted 21 lines
Regards,
LibinQuoted 17 lines
thanks,
Takashi
Quoted 6 lines
Libin Yang (4):
ALSA: Add documentation about HD-audio DP MST
ALSA: hda - addhdmi_pcmto manage hdmi pcm related features
ALSA: hda - hdmi jack created based on pcm
ALSA: hda - hdmi monitor hotplug support for dynamic pcmassignment
Quoted 2 lines
Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt | 75+++++++
Quoted 1 line
sound/pci/hda/patch_hdmi.c | 229+++++++++++++++----
Quoted 3 lines
Quoted 3 lines
--
Quoted 2 lines
2 files changed, 243 insertions(+), 61 deletions(-) create mode 100644 Documentation/sound/alsa/HD-Audio-DP-MST-
Quoted 10 lines
Quoted 5 lines
audio.txt
Quoted 4 lines
--
1.9.1_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel