Skip to contentSkip to conversation

Transform Fintek PCIE driver from 8250 to MFD

PATCH Superseded Peter Hung 6 participants 27 messages Jan 28, 2016 – Feb 16, 2016

Subsystems (3)

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore

Peter Hung

author
#0 lore raw

v2 cover Transform Fintek PCIE driver from 8250 to MFD

The Fintek F81504/508/512 is a multi-function PCIE devices. IC function list:
F81504: Max 2x8 GPIOs and max 4 serial ports
port2/3 are multi-function
F81508: Max 6x8 GPIOs and max 8 serial ports
port2/3 are multi-function, port8/9/10/11 are gpio only
F81512: Max 6x8 GPIOs and max 12 serial ports
port2/3/8/9/10/11 are multi-function

It had implemented in 8250_pci.c with basic serial port function. We want to complete it. Alan & Andy recommend us to rewrite and spilt our driver with MFD architecture.
https://lkml.org/lkml/2016/1/19/288

Paul recommed us do less code deletion to avoid confusing problem when bisect.
https://lkml.org/lkml/2016/1/18/646

So we'll do this with following patches.
1. Add MFD core driver.
2. Add GPIOLIB driver.
3. Add serial port driver.
4. Remove old driver in 8250_pci.c

It can be workable when applied patches 1~3. After apply patch 4, the device will control by F81504 MFD core driver.
Peter Hung (4):
mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core
support
gpio: gpio-f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO GPIOLIB
support
8250: 8250_f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO UART
support
serial: 8250_pci: Remove Fintek F81504/508/512 UART driver

 drivers/gpio/Kconfig                  |  10 +
 drivers/gpio/Makefile                 |   1 +
 drivers/gpio/gpio-f81504.c            | 257 ++++++++++++++++++++++++++
 drivers/mfd/Kconfig                   |  11 ++
 drivers/mfd/Makefile                  |   2 +
 drivers/mfd/f81504-core.c             | 331 ++++++++++++++++++++++++++++++++++
 drivers/tty/serial/8250/8250_f81504.c | 254 ++++++++++++++++++++++++++
 drivers/tty/serial/8250/8250_pci.c    | 201 ---------------------
 drivers/tty/serial/8250/Kconfig       |  11 ++
 drivers/tty/serial/8250/Makefile      |   1 +
 include/linux/mfd/f81504.h            |  52 ++++++
 11 files changed, 930 insertions(+), 201 deletions(-)
 create mode 100644 drivers/gpio/gpio-f81504.c
 create mode 100644 drivers/mfd/f81504-core.c
 create mode 100644 drivers/tty/serial/8250/8250_f81504.c
 create mode 100644 include/linux/mfd/f81504.h
Signature · 1 line
1.9.1
author
#1 lore raw

PATCH v2 1/4 mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

The Fintek F81504/508/512 had implemented the basic serial port function in 8250_pci.c. We try to implement high baudrate & GPIOLIB with a spilt file 8250_f81504.c, but it seems too complex to add GPIOLIB.

Alan & Andy recommend us to rewrite and spilt our driver with MFD architecture.
https://lkml.org/lkml/2016/1/19/288

This driver is core driver for F81504/508/512, it'll handle the generation of UART/GPIO platform device and initialize PCIE configuration space when probe()/resume().

IC function list:
F81504: Max 2x8 GPIOs and max 4 serial ports
port2/3 are multi-function
F81508: Max 6x8 GPIOs and max 8 serial ports
port2/3 are multi-function, port8/9/10/11 are gpio only
F81512: Max 6x8 GPIOs and max 12 serial ports
port2/3/8/9/10/11 are multi-function

H/W provider could changes the PCI configure space F0/F3h values in EEPROM or ASL code to change mode.

F0h bit0~5: Enable GPIO0~5
bit6~7: Reserve

F3h bit0~5: Multi-Functional Flag (0:GPIO/1:UART)
bit0: UART2 pin out for UART2 / GPIO0
bit1: UART3 pin out for UART3 / GPIO1
bit2: UART8 pin out for UART8 / GPIO2
bit3: UART9 pin out for UART9 / GPIO3
bit4: UART10 pin out for UART10 / GPIO4
bit5: UART11 pin out for UART11 / GPIO5 bit6~7: Reserve

---
 drivers/mfd/Kconfig        |  11 ++
 drivers/mfd/Makefile       |   2 +
 drivers/mfd/f81504-core.c  | 331 +++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/f81504.h |  52 +++++++
 4 files changed, 396 insertions(+)
 create mode 100644 drivers/mfd/f81504-core.c
 create mode 100644 include/linux/mfd/f81504.h
drivers/mfd/Kconfig +11 -0
index 9ca66de..40503a4 100644
@@ -310,6 +310,17 @@ config HTC_I2CPLD
 	  This device provides input and output GPIOs through an I2C
 	  interface to one or more sub-chips.
 
+config MFD_FINTEK_F81504_CORE
+        tristate "Fintek F81504/508/512 PCIE-to-UART/GPIO MFD support"
+        depends on PCI
+        select MFD_CORE
+        default y
+        help
+          This driver generate F81504/508/512 UART & GPIO platform
+          device. It should enable CONFIG_GPIO_F81504 to get GPIOLIB
+          support and CONFIG_8250_F81504 to get serial ports support.
+          Please bulit-in kernel if you need early console support.
+
 config MFD_INTEL_QUARK_I2C_GPIO
 	tristate "Intel Quark MFD I2C GPIO"
 	depends on PCI
drivers/mfd/Makefile +2 -0
index 0f230a6..f7382b3 100644
@@ -21,6 +21,8 @@ obj-$(CONFIG_HTC_EGPIO)		+= htc-egpio.o
 obj-$(CONFIG_HTC_PASIC3)	+= htc-pasic3.o
 obj-$(CONFIG_HTC_I2CPLD)	+= htc-i2cpld.o
 
+obj-$(CONFIG_MFD_FINTEK_F81504_CORE)	+= f81504-core.o
+
 obj-$(CONFIG_MFD_DAVINCI_VOICECODEC)	+= davinci_voicecodec.o
 obj-$(CONFIG_MFD_DM355EVM_MSP)	+= dm355evm_msp.o
 obj-$(CONFIG_MFD_TI_AM335X_TSCADC)	+= ti_am335x_tscadc.o
drivers/mfd/f81504-core.c new file +331 -0

331 lines not on this page · raw message

include/linux/mfd/f81504.h new file +52 -0

52 lines not on this page · raw message

Signature · 1 line
1.9.1
author
#11 lore raw

PATCH v2 2/4 gpio: gpio-f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO GPIOLIB support

In reply to Peter Hung

This driver is GPIOLIB driver for F81504/508/512, it'll handle the GPIOLIB operation of this device. This module will depend on MFD_FINTEK_F81504_CORE.

IC function list:
F81504: Max 2x8 GPIOs and max 4 serial ports
port2/3 are multi-function
F81508: Max 6x8 GPIOs and max 8 serial ports
port2/3 are multi-function, port8/9/10/11 are gpio only
F81512: Max 6x8 GPIOs and max 12 serial ports
port2/3/8/9/10/11 are multi-function

GPIO register:
PCI Configuration space:
F0h: bit0~5: Enable GPIO0~5
bit6~7: Reserve
F3h: bit0~5: Multi-Functional Flag (0:GPIO/1:UART)
bit0: UART2 pin out for UART2 / GPIO0
bit1: UART3 pin out for UART3 / GPIO1
bit2: UART8 pin out for UART8 / GPIO2
bit3: UART9 pin out for UART9 / GPIO3
bit4: UART10 pin out for UART10 / GPIO4
bit5: UART11 pin out for UART11 / GPIO5 bit6~7: Reserve
F1h: IO address (LSB)
F2h: IO address (MSB)
F8h + 8 * set: Direction control (bitwise)
bitx: 0 - Input mode
bitx: 1 - Output mode
F9h + 8 * set: Drive ability control (bitwise)
bitx: 0 - Open drain (default)
bitx: 1 - Push Pull
In this driver, we only implements open drain mode.

IO space:

    (IO base + 0~5): GPIO-0x~5x in/out value (bitwise)
---
 drivers/gpio/Kconfig       |  10 ++
 drivers/gpio/Makefile      |   1 +
 drivers/gpio/gpio-f81504.c | 257 +++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 268 insertions(+)
 create mode 100644 drivers/gpio/gpio-f81504.c
drivers/gpio/Kconfig +10 -0
index b18bea0..633a65f 100644
@@ -900,6 +900,16 @@ config GPIO_WM8994
 	  Say yes here to access the GPIO signals of WM8994 audio hub
 	  CODECs from Wolfson Microelectronics.
 
+config GPIO_F81504
+        tristate "Fintek F81504/508/512 PCIE-to-UART/GPIO support"
+        depends on MFD_FINTEK_F81504_CORE
+        select MFD_CORE
+        help
+          Say yes here to support the GPIO functionality of Fintek
+          F81504/508/512 PCIE-to-UART/GPIO.
+
+          If unsure, say N.
+
 endmenu
 
 menu "PCI GPIO expanders"
drivers/gpio/Makefile +1 -0
index 986dbd8..06fb240 100644
@@ -111,6 +111,7 @@ obj-$(CONFIG_GPIO_VX855)	+= gpio-vx855.o
 obj-$(CONFIG_GPIO_WM831X)	+= gpio-wm831x.o
 obj-$(CONFIG_GPIO_WM8350)	+= gpio-wm8350.o
 obj-$(CONFIG_GPIO_WM8994)	+= gpio-wm8994.o
+obj-$(CONFIG_GPIO_F81504)       += gpio-f81504.o
 obj-$(CONFIG_GPIO_XGENE)	+= gpio-xgene.o
 obj-$(CONFIG_GPIO_XGENE_SB)	+= gpio-xgene-sb.o
 obj-$(CONFIG_GPIO_XILINX)	+= gpio-xilinx.o
drivers/gpio/gpio-f81504.c new file +257 -0

257 lines not on this page · raw message

Signature · 1 line
1.9.1
author
#18 lore raw

PATCH v2 3/4 8250: 8250_f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO UART support

In reply to Peter Hung

This driver is 8250 driver for F81504/508/512, it'll handle the serial port operation of this device. This module will depend on MFD_FINTEK_F81504_CORE.

The serial ports support from 50bps to 1.5Mbps with Linux baudrate define excluding 1.0Mbps due to not support 16MHz clock source.

PCI Configuration Space Registers, set:0~11(Max):
40h + 8 * set:
bit7~6: Clock source selector
00: 1.8432MHz
01: 18.432MHz
10: 24MHz
11: 14.769MHz
bit0: UART enable
41h + 8 * set:
bit5~4: RX trigger multiple
00: 1x * trigger level
01: 2x * trigger level
10: 4x * trigger level
11: 8x * trigger level
bit1~0: FIFO Size
11: 128Bytes
44h + 8 * set: UART IO address (LSB)
45h + 8 * set: UART IO address (MSB)
47h + 8 * set:
bit5: RTS invert (bit4 must enable)
bit4: RTS auto direction enable
0: RTS control by MCR
1: RTS driven high when TX, otherwise low

---
 drivers/tty/serial/8250/8250_f81504.c | 254 ++++++++++++++++++++++++++++++++++
 drivers/tty/serial/8250/Kconfig       |  11 ++
 drivers/tty/serial/8250/Makefile      |   1 +
 3 files changed, 266 insertions(+)
 create mode 100644 drivers/tty/serial/8250/8250_f81504.c
drivers/tty/serial/8250/8250_f81504.c new file +254 -0
new file mode 100644
index 0000000..543661f
@@ -0,0 +1,254 @@
+#include <linux/pci.h>
+#include <linux/serial_8250.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/mfd/f81504.h>
+
+#include "8250.h"
+
+static u32 baudrate_table[] = { 1500000, 1152000, 921600 };
+static u8 clock_table[] = { F81504_CLKSEL_24_MHZ, F81504_CLKSEL_18DOT46_MHZ,
+				F81504_CLKSEL_14DOT77_MHZ };
+
+/* We should do proper H/W transceiver setting before change to RS485 mode */
+static int f81504_rs485_config(struct uart_port *port,
+			       struct serial_rs485 *rs485)
+{
+	u8 setting;
+	u8 *index = (u8 *) port->private_data;
+	struct platform_device *pdev = container_of(port->dev,
+					struct platform_device, dev);
+	struct pci_dev *pci_dev = to_pci_dev(pdev->dev.parent);
+
+	pci_read_config_byte(pci_dev, F81504_UART_START_ADDR +
+			F81504_UART_OFFSET * *index + F81504_UART_MODE_OFFSET,
+			&setting);
+
+	if (!rs485)
+		rs485 = &port->rs485;
+	else if (rs485->flags & SER_RS485_ENABLED)
+		memset(rs485->padding, 0, sizeof(rs485->padding));
+	else
+		memset(rs485, 0, sizeof(*rs485));
+
+	/* F81504/508/512 not support RTS delay before or after send */
+	rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND;
+
+	if (rs485->flags & SER_RS485_ENABLED) {
+		/* Enable RTS H/W control mode */
+		setting |= F81504_RTS_CONTROL_BY_HW;
+
+		if (rs485->flags & SER_RS485_RTS_ON_SEND) {
+			/* RTS driving high on TX */
+			setting &= ~F81504_RTS_INVERT;
+		} else {
+			/* RTS driving low on TX */
+			setting |= F81504_RTS_INVERT;
+		}
+
+		rs485->delay_rts_after_send = 0;
+		rs485->delay_rts_before_send = 0;
+	} else {
+		/* Disable RTS H/W control mode */
+		setting &= ~(F81504_RTS_CONTROL_BY_HW | F81504_RTS_INVERT);
+	}
+
+	pci_write_config_byte(pci_dev, F81504_UART_START_ADDR +
+			F81504_UART_OFFSET * *index + F81504_UART_MODE_OFFSET,
+			setting);
+
+	if (rs485 != &port->rs485)
+		port->rs485 = *rs485;
+
+	return 0;
+}
+
+static int f81504_check_baudrate(u32 baud, size_t *idx)
+{
+	size_t index;
+	u32 quot, rem;
+
+	for (index = 0; index < ARRAY_SIZE(baudrate_table); ++index) {
+		/* Clock source must largeer than desire baudrate */
+		if (baud > baudrate_table[index])
+			continue;
+
+		quot = DIV_ROUND_CLOSEST(baudrate_table[index], baud);
+		/* find divisible clock source */
+		rem = baudrate_table[index] % baud;
+
+		if (quot && !rem) {
+			if (idx)
+				*idx = index;
+			return 0;
+		}
+	}
+
+	return -EINVAL;
+}
+
+static void f81504_set_termios(struct uart_port *port,
+		struct ktermios *termios, struct ktermios *old)
+{
+	struct platform_device *pdev = container_of(port->dev,
+					struct platform_device, dev);
+	struct pci_dev *dev = to_pci_dev(pdev->dev.parent);
+	unsigned int baud = tty_termios_baud_rate(termios);
+	u8 tmp, *offset = (u8 *) port->private_data;
+	size_t i;
+
+	do {
+		/* read current clock source (masked with CLOCK_RATE_MASK) */
+		pci_read_config_byte(dev, F81504_UART_START_ADDR + *offset *
+				F81504_UART_OFFSET, &tmp);
+
+		if (baud <= 115200) {
+			/*
+			 * direct use 1.8432MHz when baudrate smaller then or
+			 * equal 115200bps
+			 */
+			port->uartclk = 115200 * 16;
+			pci_write_config_byte(dev, F81504_UART_START_ADDR +
+					*offset * F81504_UART_OFFSET,
+					tmp & ~F81504_CLOCK_RATE_MASK);
+			break;
+		}
+
+		if (!f81504_check_baudrate(baud, &i)) {
+			/* had optimize value */
+			port->uartclk = baudrate_table[i] * 16;
+			tmp = (tmp & ~F81504_CLOCK_RATE_MASK) | clock_table[i];
+			pci_write_config_byte(dev, F81504_UART_START_ADDR +
+					*offset * F81504_UART_OFFSET, tmp);
+			break;
+		}
+
+		if (old && !f81504_check_baudrate(tty_termios_baud_rate(old),
+				NULL)) {
+			/*
+			 * If it can't found suitable clock source but had old
+			 * accpetable baudrate, we'll use it
+			 */
+			baud = tty_termios_baud_rate(old);
+		} else {
+			/*
+			 * If it can't found suitable clock source and not old
+			 * config, we'll direct set 115200bps for future use
+			 */
+			baud = 115200;
+		}
+
+		if (tty_termios_baud_rate(termios))
+			tty_termios_encode_baud_rate(termios, baud, baud);
+	} while (1);
+
+	serial8250_do_set_termios(port, termios, old);
+}
+
+static int f81504_register_port(struct platform_device *dev,
+		unsigned long address, int idx)
+{
+	struct pci_dev *pci_dev = to_pci_dev(dev->dev.parent);
+	struct uart_8250_port port;
+	u8 *data;
+
+	memset(&port, 0, sizeof(port));
+	data = devm_kzalloc(&dev->dev, sizeof(u8), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	*data = idx;
+	port.port.iotype = UPIO_PORT;
+	port.port.irq = pci_dev->irq;
+	port.port.flags = UPF_SKIP_TEST | UPF_FIXED_TYPE | UPF_BOOT_AUTOCONF |
+			UPF_SHARE_IRQ;
+	port.port.uartclk = 1843200;
+	port.port.dev = &dev->dev;
+	port.port.iobase = address;
+	port.port.type = PORT_16550A;
+	port.port.fifosize = 128;
+	port.port.rs485_config = f81504_rs485_config;
+	port.port.set_termios = f81504_set_termios;
+	port.tx_loadsz = 32;
+	port.port.private_data = data;	/* save current idx */
+
+	return serial8250_register_8250_port(&port);
+}
+
+static int f81504_serial_probe(struct platform_device *pdev)
+{
+	int line;
+	size_t *index = (size_t *)dev_get_platdata(&pdev->dev);
+	struct resource *io = platform_get_resource(pdev, IORESOURCE_IO, 0);
+
+	line = f81504_register_port(pdev, io->start, *index);
+	if (line < 0)
+		return line;
+
+	/*
+	 * Re-assign line to replace old port PCIE configuration space idx,
+	 * port idx is saved in per-port private data.
+	 */
+	*index = line;
+	return 0;
+}
+
+static int f81504_serial_remove(struct platform_device *pdev)
+{
+	size_t *line = (size_t *)dev_get_platdata(&pdev->dev);
+
+	serial8250_unregister_port(*line);
+	return 0;
+}
+
+
+#ifdef CONFIG_PM_SLEEP
+static int f81504_serial_suspend(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	size_t *line = (size_t *)dev_get_platdata(&pdev->dev);
+
+	serial8250_suspend_port(*line);
+	return 0;
+}
+
+static int f81504_serial_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	size_t *line = (size_t *)dev_get_platdata(&pdev->dev);
+	struct uart_8250_port *port = serial8250_get_port(*line);
+
+	f81504_rs485_config(&port->port, NULL);
+	serial8250_resume_port(*line);
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(f81504_serial_pm_ops, f81504_serial_suspend,
+		f81504_serial_resume);
+
+static struct platform_driver f81504_serial_driver = {
+	.driver = {
+		.name	= F81504_SERIAL_NAME,
+		.owner	= THIS_MODULE,
+		.pm     = &f81504_serial_pm_ops,
+	},
+	.probe		= f81504_serial_probe,
+	.remove		= f81504_serial_remove,
+};
+
+static int __init f81504_serial_init(void)
+{
+	return platform_driver_register(&f81504_serial_driver);
+}
+subsys_initcall(f81504_serial_init);
+
+static void __exit f81504_serial_exit(void)
+{
+	platform_driver_unregister(&f81504_serial_driver);
+}
+module_exit(f81504_serial_exit);
+
+MODULE_AUTHOR("Peter Hong <[email protected]>");
+MODULE_DESCRIPTION("Fintek F81504/508/512 PCIE 16550A serial port driver");
+MODULE_LICENSE("GPL");
drivers/tty/serial/8250/Kconfig +11 -0
index 6412f14..736d467 100644
@@ -116,6 +116,17 @@ config SERIAL_8250_PCI
 	  Note that serial ports on NetMos 9835 Multi-I/O cards are handled
 	  by the parport_serial driver, enabled with CONFIG_PARPORT_SERIAL.
 
+config SERIAL_8250_F81504
+        tristate "Fintek F81504/508/512 16550 PCIE device support" if EXPERT
+        depends on SERIAL_8250 && MFD_FINTEK_F81504_CORE
+        default SERIAL_8250
+        select RATIONAL
+        help
+          This builds Fintek F81504/508/512 PCIE serial ports support.
+          You may be able to enable GPIO_F81504 to get GPIOLIB support if
+          the devices supported. Please enable MFD_FINTEK_F81504_CORE &
+          this with Y if you need a early console.
+
 config SERIAL_8250_HP300
 	tristate
 	depends on SERIAL_8250 && HP300
drivers/tty/serial/8250/Makefile +1 -0
index e177f86..9e8c549 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_SERIAL_8250)		+= 8250.o 8250_base.o
 8250_base-$(CONFIG_SERIAL_8250_DMA)	+= 8250_dma.o
 obj-$(CONFIG_SERIAL_8250_GSC)		+= 8250_gsc.o
 obj-$(CONFIG_SERIAL_8250_PCI)		+= 8250_pci.o
+obj-$(CONFIG_SERIAL_8250_F81504)	+= 8250_f81504.o
 obj-$(CONFIG_SERIAL_8250_HP300)		+= 8250_hp300.o
 obj-$(CONFIG_SERIAL_8250_CS)		+= serial_cs.o
 obj-$(CONFIG_SERIAL_8250_ACORN)		+= 8250_acorn.o
Signature · 1 line
1.9.1
author
#22 lore raw

PATCH v2 4/4 serial: 8250_pci: Remove Fintek F81504/508/512 UART driver

In reply to Peter Hung

Remove Fintek F81504/508/512 PCIE-to-UART device driver from 8250_pci.c

Paul recommed us do less code deletion to avoid confusing problem when bisect.
https://lkml.org/lkml/2016/1/18/646

But this patch is sent after with following patch.
8250: 8250_f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO UART support
mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

We must remove F81504/508/512 support in 8250_pci.c and migrate to f81504-core/8250_f81504 to enable MFD support.

---
 drivers/tty/serial/8250/8250_pci.c | 201 -------------------------------------
 1 file changed, 201 deletions(-)
drivers/tty/serial/8250/8250_pci.c +0 -201
index 4097f3f..0eeb4a3 100644
@@ -1527,156 +1527,6 @@ pci_brcm_trumanage_setup(struct serial_private *priv,
 	return ret;
 }
 
-/* RTS will control by MCR if this bit is 0 */
-#define FINTEK_RTS_CONTROL_BY_HW	BIT(4)
-/* only worked with FINTEK_RTS_CONTROL_BY_HW on */
-#define FINTEK_RTS_INVERT		BIT(5)
-
-/* We should do proper H/W transceiver setting before change to RS485 mode */
-static int pci_fintek_rs485_config(struct uart_port *port,
-			       struct serial_rs485 *rs485)
-{
-	u8 setting;
-	u8 *index = (u8 *) port->private_data;
-	struct pci_dev *pci_dev = container_of(port->dev, struct pci_dev,
-						dev);
-
-	pci_read_config_byte(pci_dev, 0x40 + 8 * *index + 7, &setting);
-
-	if (!rs485)
-		rs485 = &port->rs485;
-	else if (rs485->flags & SER_RS485_ENABLED)
-		memset(rs485->padding, 0, sizeof(rs485->padding));
-	else
-		memset(rs485, 0, sizeof(*rs485));
-
-	/* F81504/508/512 not support RTS delay before or after send */
-	rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND;
-
-	if (rs485->flags & SER_RS485_ENABLED) {
-		/* Enable RTS H/W control mode */
-		setting |= FINTEK_RTS_CONTROL_BY_HW;
-
-		if (rs485->flags & SER_RS485_RTS_ON_SEND) {
-			/* RTS driving high on TX */
-			setting &= ~FINTEK_RTS_INVERT;
-		} else {
-			/* RTS driving low on TX */
-			setting |= FINTEK_RTS_INVERT;
-		}
-
-		rs485->delay_rts_after_send = 0;
-		rs485->delay_rts_before_send = 0;
-	} else {
-		/* Disable RTS H/W control mode */
-		setting &= ~(FINTEK_RTS_CONTROL_BY_HW | FINTEK_RTS_INVERT);
-	}
-
-	pci_write_config_byte(pci_dev, 0x40 + 8 * *index + 7, setting);
-
-	if (rs485 != &port->rs485)
-		port->rs485 = *rs485;
-
-	return 0;
-}
-
-static int pci_fintek_setup(struct serial_private *priv,
-			    const struct pciserial_board *board,
-			    struct uart_8250_port *port, int idx)
-{
-	struct pci_dev *pdev = priv->dev;
-	u8 *data;
-	u8 config_base;
-	u16 iobase;
-
-	config_base = 0x40 + 0x08 * idx;
-
-	/* Get the io address from configuration space */
-	pci_read_config_word(pdev, config_base + 4, &iobase);
-
-	dev_dbg(&pdev->dev, "%s: idx=%d iobase=0x%x", __func__, idx, iobase);
-
-	port->port.iotype = UPIO_PORT;
-	port->port.iobase = iobase;
-	port->port.rs485_config = pci_fintek_rs485_config;
-
-	data = devm_kzalloc(&pdev->dev, sizeof(u8), GFP_KERNEL);
-	if (!data)
-		return -ENOMEM;
-
-	/* preserve index in PCI configuration space */
-	*data = idx;
-	port->port.private_data = data;
-
-	return 0;
-}
-
-static int pci_fintek_init(struct pci_dev *dev)
-{
-	unsigned long iobase;
-	u32 max_port, i;
-	u32 bar_data[3];
-	u8 config_base;
-	struct serial_private *priv = pci_get_drvdata(dev);
-	struct uart_8250_port *port;
-
-	switch (dev->device) {
-	case 0x1104: /* 4 ports */
-	case 0x1108: /* 8 ports */
-		max_port = dev->device & 0xff;
-		break;
-	case 0x1112: /* 12 ports */
-		max_port = 12;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	/* Get the io address dispatch from the BIOS */
-	pci_read_config_dword(dev, 0x24, &bar_data[0]);
-	pci_read_config_dword(dev, 0x20, &bar_data[1]);
-	pci_read_config_dword(dev, 0x1c, &bar_data[2]);
-
-	for (i = 0; i < max_port; ++i) {
-		/* UART0 configuration offset start from 0x40 */
-		config_base = 0x40 + 0x08 * i;
-
-		/* Calculate Real IO Port */
-		iobase = (bar_data[i / 4] & 0xffffffe0) + (i % 4) * 8;
-
-		/* Enable UART I/O port */
-		pci_write_config_byte(dev, config_base + 0x00, 0x01);
-
-		/* Select 128-byte FIFO and 8x FIFO threshold */
-		pci_write_config_byte(dev, config_base + 0x01, 0x33);
-
-		/* LSB UART */
-		pci_write_config_byte(dev, config_base + 0x04,
-				(u8)(iobase & 0xff));
-
-		/* MSB UART */
-		pci_write_config_byte(dev, config_base + 0x05,
-				(u8)((iobase & 0xff00) >> 8));
-
-		pci_write_config_byte(dev, config_base + 0x06, dev->irq);
-
-		if (priv) {
-			/* re-apply RS232/485 mode when
-			 * pciserial_resume_ports()
-			 */
-			port = serial8250_get_port(priv->line[i]);
-			pci_fintek_rs485_config(&port->port, NULL);
-		} else {
-			/* First init without port data
-			 * force init to RS232 Mode
-			 */
-			pci_write_config_byte(dev, config_base + 0x07, 0x01);
-		}
-	}
-
-	return max_port;
-}
-
 static int skip_tx_en_setup(struct serial_private *priv,
 			const struct pciserial_board *board,
 			struct uart_8250_port *port, int idx)
@@ -2707,31 +2557,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.subdevice	= PCI_ANY_ID,
 		.setup		= pci_brcm_trumanage_setup,
 	},
-	{
-		.vendor		= 0x1c29,
-		.device		= 0x1104,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_fintek_setup,
-		.init		= pci_fintek_init,
-	},
-	{
-		.vendor		= 0x1c29,
-		.device		= 0x1108,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_fintek_setup,
-		.init		= pci_fintek_init,
-	},
-	{
-		.vendor		= 0x1c29,
-		.device		= 0x1112,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_fintek_setup,
-		.init		= pci_fintek_init,
-	},
-
 	/*
 	 * Default "match everything" terminator entry
 	 */
@@ -2933,9 +2758,6 @@ enum pci_board_num_t {
 	pbn_omegapci,
 	pbn_NETMOS9900_2s_115200,
 	pbn_brcm_trumanage,
-	pbn_fintek_4,
-	pbn_fintek_8,
-	pbn_fintek_12,
 	pbn_wch384_4,
 	pbn_pericom_PI7C9X7951,
 	pbn_pericom_PI7C9X7952,
@@ -3738,24 +3560,6 @@ static struct pciserial_board pci_boards[] = {
 		.reg_shift	= 2,
 		.base_baud	= 115200,
 	},
-	[pbn_fintek_4] = {
-		.num_ports	= 4,
-		.uart_offset	= 8,
-		.base_baud	= 115200,
-		.first_offset	= 0x40,
-	},
-	[pbn_fintek_8] = {
-		.num_ports	= 8,
-		.uart_offset	= 8,
-		.base_baud	= 115200,
-		.first_offset	= 0x40,
-	},
-	[pbn_fintek_12] = {
-		.num_ports	= 12,
-		.uart_offset	= 8,
-		.base_baud	= 115200,
-		.first_offset	= 0x40,
-	},
 	[pbn_wch384_4] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 4,
@@ -5581,11 +5385,6 @@ static struct pci_device_id serial_pci_tbl[] = {
 		0,
 		0, pbn_exar_XR17V358 },
 
-	/* Fintek PCI serial cards */
-	{ PCI_DEVICE(0x1c29, 0x1104), .driver_data = pbn_fintek_4 },
-	{ PCI_DEVICE(0x1c29, 0x1108), .driver_data = pbn_fintek_8 },
-	{ PCI_DEVICE(0x1c29, 0x1112), .driver_data = pbn_fintek_12 },
-
 	/*
 	 * These entries match devices with class COMMUNICATION_SERIAL,
 	 * COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL
Signature · 1 line
1.9.1
#12 lore raw

[PATCH] gpio: gpio-f81504: fix platform_no_drv_owner.cocci warnings

In reply to Peter Hung
drivers/gpio/gpio-f81504.c:246:3-8: No need to set .owner here. The core will do it.

drivers/gpio/gpio-f81504.c:246:3-8: No need to set .owner here. The core will do it.

Remove .owner field if calls are used which set it automatically

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci

---

 gpio-f81504.c |    1 -
 1 file changed, 1 deletion(-)
drivers/gpio/gpio-f81504.c +0 -1
@@ -243,7 +243,6 @@ static SIMPLE_DEV_PM_OPS(f81504_gpio_pm_
 static struct platform_driver f81504_gpio_driver = {
 	.driver = {
 		.name	= F81504_GPIO_NAME,
-		.owner	= THIS_MODULE,
 		.pm     = &f81504_gpio_pm_ops,
 	},
 	.probe		= f81504_gpio_probe,
#13 lore raw

Re: [PATCH V2 2/4] gpio: gpio-f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO GPIOLIB support

In reply to Peter Hung
reproduce:

Hi Peter,

[auto build test ERROR on gpio/for-next]
[also build test ERROR on v4.5-rc1 next-20160128]
[if your patch is applied to the wrong git tree, please drop us a note to help improving the system]

url:    https://github.com/0day-ci/linux/commits/Peter-Hung/Transform-Fintek-PCIE-driver-from-8250-to-MFD/20160128-172929
base:   https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio.git for-next
config: i386-allmodconfig (attached as .config)
reproduce:
        # save the attached .config to linux build tree
        make ARCH=i386 

All error/warnings (new ones prefixed by >>):

In file included from include/linux/list.h:8:0,

                    from include/linux/kobject.h:20,
                    from include/linux/device.h:17,
                    from include/linux/platform_device.h:14,
                    from drivers/gpio/gpio-f81504.c:18:
   drivers/gpio/gpio-f81504.c: In function 'f81504_gpio_direction_in':
>> drivers/gpio/gpio-f81504.c:41:56: error: 'struct gpio_chip' has no member named 'dev'
     struct platform_device *pdev = to_platform_device(chip->dev);
                                                           ^
   include/linux/kernel.h:841:49: note: in definition of macro 'container_of'
     const typeof( ((type *)0)->member ) *__mptr = (ptr); \
                                                    ^
>> drivers/gpio/gpio-f81504.c:41:33: note: in expansion of macro 'to_platform_device'
     struct platform_device *pdev = to_platform_device(chip->dev);
                                    ^
   drivers/gpio/gpio-f81504.c: In function 'f81504_gpio_direction_out':
   drivers/gpio/gpio-f81504.c:63:56: error: 'struct gpio_chip' has no member named 'dev'
     struct platform_device *pdev = to_platform_device(chip->dev);
                                                           ^
   include/linux/kernel.h:841:49: note: in definition of macro 'container_of'
     const typeof( ((type *)0)->member ) *__mptr = (ptr); \
                                                    ^
   drivers/gpio/gpio-f81504.c:63:33: note: in expansion of macro 'to_platform_device'
     struct platform_device *pdev = to_platform_device(chip->dev);
                                    ^
   drivers/gpio/gpio-f81504.c: In function 'f81504_gpio_get_direction':
   drivers/gpio/gpio-f81504.c:104:56: error: 'struct gpio_chip' has no member named 'dev'
     struct platform_device *pdev = to_platform_device(chip->dev);
                                                           ^
   include/linux/kernel.h:841:49: note: in definition of macro 'container_of'
     const typeof( ((type *)0)->member ) *__mptr = (ptr); \
                                                    ^
   drivers/gpio/gpio-f81504.c:104:33: note: in expansion of macro 'to_platform_device'
     struct platform_device *pdev = to_platform_device(chip->dev);
                                    ^
   drivers/gpio/gpio-f81504.c: In function 'f81504_gpio_get':
   drivers/gpio/gpio-f81504.c:122:56: error: 'struct gpio_chip' has no member named 'dev'
     struct platform_device *pdev = to_platform_device(chip->dev);
                                                           ^
   include/linux/kernel.h:841:49: note: in definition of macro 'container_of'
     const typeof( ((type *)0)->member ) *__mptr = (ptr); \
                                                    ^
   drivers/gpio/gpio-f81504.c:122:33: note: in expansion of macro 'to_platform_device'
     struct platform_device *pdev = to_platform_device(chip->dev);
                                    ^
   drivers/gpio/gpio-f81504.c: In function 'f81504_gpio_probe':
   drivers/gpio/gpio-f81504.c:212:10: error: 'struct gpio_chip' has no member named 'dev'
     gc->chip.dev = &pdev->dev;
             ^

coccinelle warnings: (new ones prefixed by >>)

>> drivers/gpio/gpio-f81504.c:246:3-8: No need to set .owner here. The core will do it.

Please review and possibly fold the followup patch.

vim +41 drivers/gpio/gpio-f81504.c

12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
13 * GNU General Public License for more details.
14 *
15 * You should have received a copy of the GNU General Public License
16 * along with this program. If not, see <http://www.gnu.org/licenses/>.
17 */

  > 18	#include <linux/platform_device.h>
    19	#include <linux/gpio.h>
    20	#include <linux/pci.h>
    21	#include <linux/mfd/f81504.h>
    22	
    23	struct f81504_gpio_chip {
    24		struct gpio_chip chip;
    25		struct mutex locker;
    26		u8 idx;
    27		u8 save_out_en;
    28		u8 save_drive_en;
    29		u8 save_value;
    30	};
    31	
    32	static struct f81504_gpio_chip *gpio_to_f81504_chip(struct gpio_chip *chip)
    33	{
    34		return container_of(chip, struct f81504_gpio_chip, chip);
    35	}
    36	
    37	static int f81504_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
    38	{
    39		u8 tmp;
    40		struct f81504_gpio_chip *gc = gpio_to_f81504_chip(chip);
  > 41		struct platform_device *pdev = to_platform_device(chip->dev);
    42		struct pci_dev *pci_dev = to_pci_dev(pdev->dev.parent);
    43	
    44		mutex_lock(&gc->locker);

---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation

#2 lore raw

Re: [PATCH V2 1/4] mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

In reply to Peter Hung

drivers/mfd/Kconfig config HTC_I2CPLD · line 319

Quoted 7 lines
drivers/mfd/Kconfig +7 -0
+config MFD_FINTEK_F81504_CORE
+        tristate "Fintek F81504/508/512 PCIE-to-UART/GPIO MFD support"
+        depends on PCI
+        select MFD_CORE
+        default y
+        help
+          This driver generate F81504/508/512 UART & GPIO platform

This driver provides the F81504/508/512 UART & GPIO platform

Quoted 1 line

+ device. It should enable CONFIG_GPIO_F81504 to get GPIOLIB

devices. You should enable CONFIG_GPIO_F81504 to get GPIOLIB

Quoted 1 line

+ support and CONFIG_8250_F81504 to get serial ports support.

port rather than ports

Quoted 1 line

+ Please bulit-in kernel if you need early console support.

This driver needs to be built into the kernel to use early console support.

drivers/mfd/f81504-core.c line 72

Quoted 6 lines
drivers/mfd/f81504-core.c new file +6 -0
+	switch (dev->device) {
+	case FINTEK_F81504: /* 4 ports */
+		/* F81504 max 2 sets of GPIO, others are max 6 sets*/
+		gpio_en &= 0x03;
+	case FINTEK_F81508: /* 8 ports */
+		max_port = dev->device & 0xff;

If that is meant to fall through from F81504 into F81508 it's worth commenting, otherwise someone reviewing the code can't always be sure it was intentional.

Quoted 6 lines
drivers/mfd/f81504-core.c new file +6 -0
+		break;
+	case FINTEK_F81512: /* 12 ports */
+		max_port = 12;
+		break;
+	default:
+		return -EINVAL;

drivers/mfd/f81504-core.c line 88

Quoted 10 lines
drivers/mfd/f81504-core.c new file +10 -0
+	}
+
+	/* rewrite GPIO Mode setting */
+	pci_write_config_byte(dev, F81504_GPIO_ENABLE_REG, gpio_en & 0x3f);
+	pci_write_config_byte(dev, F81504_GPIO_MODE_REG, ~gpio_en & 0x3f);
+
+	/* Get the UART IO address dispatch from the BIOS */
+	pci_read_config_dword(dev, 0x24, &bar_data[0]);
+	pci_read_config_dword(dev, 0x20, &bar_data[1]);
+	pci_read_config_dword(dev, 0x1c, &bar_data[2]);

Take these from the pci device itself. On some non PC platforms the values in the pci bar may be remapped by bridges and not give you the true answer.

pci_resource_start(dev, barnumber)

Alan

Reviewed-by on v2 3/4
#19 lore raw

Re: [PATCH V2 3/4] 8250: 8250_f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO UART support

In reply to Peter Hung
Quoted 31 lines · On Thu, 28 Jan 2016 17:20:37 +0800 Peter Hung <[email protected]> wrote:

This driver is 8250 driver for F81504/508/512, it'll handle the serial port operation of this device. This module will depend on MFD_FINTEK_F81504_CORE.

The serial ports support from 50bps to 1.5Mbps with Linux baudrate define excluding 1.0Mbps due to not support 16MHz clock source.

PCI Configuration Space Registers, set:0~11(Max):
40h + 8 * set:
bit7~6: Clock source selector
00: 1.8432MHz
01: 18.432MHz
10: 24MHz
11: 14.769MHz
bit0: UART enable
41h + 8 * set:
bit5~4: RX trigger multiple
00: 1x * trigger level
01: 2x * trigger level
10: 4x * trigger level
11: 8x * trigger level
bit1~0: FIFO Size
11: 128Bytes
44h + 8 * set: UART IO address (LSB)
45h + 8 * set: UART IO address (MSB)
47h + 8 * set:
bit5: RTS invert (bit4 must enable)
bit4: RTS auto direction enable
0: RTS control by MCR
1: RTS driven high when TX, otherwise low

Quoted 3 lines

Nice

It and the GPIO driver parts

Alan

#20 lore raw

[PATCH] 8250: 8250_f81504: fix platform_no_drv_owner.cocci warnings

In reply to Peter Hung
drivers/tty/serial/8250/8250_f81504.c:233:3-8: No need to set .owner here. The core will do it.

drivers/tty/serial/8250/8250_f81504.c:233:3-8: No need to set .owner here. The core will do it.

Remove .owner field if calls are used which set it automatically

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci

---

 8250_f81504.c |    1 -
 1 file changed, 1 deletion(-)
drivers/tty/serial/8250/8250_f81504.c +0 -1
@@ -230,7 +230,6 @@ static SIMPLE_DEV_PM_OPS(f81504_serial_p
 static struct platform_driver f81504_serial_driver = {
 	.driver = {
 		.name	= F81504_SERIAL_NAME,
-		.owner	= THIS_MODULE,
 		.pm     = &f81504_serial_pm_ops,
 	},
 	.probe		= f81504_serial_probe,
#21 lore raw

Re: [PATCH V2 3/4] 8250: 8250_f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO UART support

In reply to Peter Hung
coccinelle warnings: (new ones prefixed by >>)

Hi Peter,

[auto build test WARNING on gpio/for-next]
[also build test WARNING on v4.5-rc1 next-20160128]
[if your patch is applied to the wrong git tree, please drop us a note to help improving the system]

url:    https://github.com/0day-ci/linux/commits/Peter-Hung/Transform-Fintek-PCIE-driver-from-8250-to-MFD/20160128-172929
base:   https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio.git for-next

coccinelle warnings: (new ones prefixed by >>)

>> drivers/tty/serial/8250/8250_f81504.c:233:3-8: No need to set .owner here. The core will do it.

Please review and possibly fold the followup patch.

---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation

#4 lore raw

Re: [PATCH V2 1/4] mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

In reply to Peter Hung
Quoted 9 lines · Peter Hung

The Fintek F81504/508/512 had implemented the basic serial port function in
8250_pci.c. We try to implement high baudrate & GPIOLIB with a spilt file
8250_f81504.c, but it seems too complex to add GPIOLIB.

Alan & Andy recommend us to rewrite and spilt our driver with MFD architecture.
https://lkml.org/lkml/2016/1/19/288

My comments below.

Quoted 13 lines
drivers/mfd/Kconfig +0 -0
@@ -310,6 +310,17 @@ config HTC_I2CPLD

    This device provides input and output GPIOs through an I2C interface to one or more sub-chips.

+config MFD_FINTEK_F81504_CORE
+        tristate "Fintek F81504/508/512 PCIE-to-UART/GPIO MFD support"
+        depends on PCI
+        select MFD_CORE

Quoted 1 line

+        default y

I'm not sure we have to have this always y. Perhaps default SERIAL_8250_PCI

Quoted 8 lines
drivers/mfd/Makefile +0 -0
@@ -21,6 +21,8 @@ obj-$(CONFIG_HTC_EGPIO)		+= htc-

egpio.o
 obj-$(CONFIG_HTC_PASIC3) += htc-pasic3.o
 obj-$(CONFIG_HTC_I2CPLD) += htc-i2cpld.o

+obj-$(CONFIG_MFD_FINTEK_F81504_CORE) += f81504-core.o

I think '_' is better than '-'. What I saw and usually do is '_' for regular source modules and '-' for the resulting objects when they have more than one file.

Quoted 7 lines
drivers/mfd/f81504-core.c new file +2 -0
@@ -0,0 +1,331 @@
+/*
+ * Core operations for Fintek F81504/508/512 PCIE-to-UART/GPIO

device
+ */

drivers/mfd/f81504-core.c line 12

Quoted 9 lines
drivers/mfd/f81504-core.c new file +9 -0
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/f81504.h>
+
+#define F81504_DRIVER_NAME	"f81504_core"

Yeah, exactly.

Quoted 2 lines

+#define F81504_DEV_DESC "Fintek F81504/508/512 PCIE-
to-UART core"

Do you need this definition? Is it used more than once?

Quoted 5 lines
drivers/mfd/f81504-core.c new file +3 -0
+#define F81504_IO_REGION	8
+
+const u8 fintek_gpio_mapping[F81504_MAX_GPIO_CNT] = { 2, 3, 8, 9,

10, 11 };

drivers/mfd/f81504-core.c new file +1 -0
+EXPORT_SYMBOL(fintek_gpio_mapping);

drivers/mfd/f81504-core.c line 27

Quoted 10 lines
drivers/mfd/f81504-core.c new file +10 -0
+
+static int f81504_port_init(struct pci_dev *dev)
+{
+	size_t i, j;
+	u32 max_port, iobase, gpio_addr;
+	u32 bar_data[3];
+	u16 tmp;
+	u8 config_base, gpio_en, f0h_data, f3h_data;
+	bool is_gpio;
+	struct f81504_pci_private *priv = pci_get_drvdata(dev);

I would suggest to rearrange definition block here (and in the rest of the functions in entire series) to somehow follow the following pattern

1) assignments go first, especially container_of() based ones;
2) group variables by meaning and put longer lines upper;
3) return value variable, if exists, goes last.

Besides that choose types carefully. If there is known limit for counters, no need to define wider type than needed. Use proper types for corresponding values.

drivers/mfd/f81504-core.c line 34

Quoted 11 lines
drivers/mfd/f81504-core.c new file +5 -0
+
+	/* Init GPIO IO Address */
+	pci_read_config_dword(dev, 0x18, &gpio_addr);
+	gpio_addr &= 0xffffffe0;
 
 
+	pci_write_config_byte(dev, F81504_GPIO_IO_LSB_REG, gpio_addr

& 0xff);

drivers/mfd/f81504-core.c new file +1 -0
+	pci_write_config_byte(dev, F81504_GPIO_IO_MSB_REG,

(gpio_addr >> 8) &

drivers/mfd/f81504-core.c new file +1 -0
+			0xff);

Could it be written at once as a word?

drivers/mfd/f81504-core.c line 54

Quoted 6 lines
drivers/mfd/f81504-core.c new file +2 -0
+	if (priv) {
+		/* Reinit from resume(), read the previous value

from priv */

drivers/mfd/f81504-core.c new file +1 -0
+		gpio_en = priv->gpio_en;

I would suggest to move this line down to follow same pattern in else branch.

drivers/mfd/f81504-core.c

Quoted 2 lines
drivers/mfd/f81504-core.c new file +2 -0
+
+		/* re-save GPIO IO addr for called by resume() */

re-save -> Re-save
addr -> address

drivers/mfd/f81504-core.c

Quoted 9 lines
drivers/mfd/f81504-core.c new file +4 -0
+		priv->gpio_ioaddr = gpio_addr;
+	} else {
+		/* Driver first init */
+		pci_read_config_byte(dev, F81504_GPIO_ENABLE_REG,

&f0h_data);

drivers/mfd/f81504-core.c new file +1 -0
+		pci_read_config_byte(dev, F81504_GPIO_MODE_REG,

&f3h_data);

drivers/mfd/f81504-core.c new file +2 -0
+
+		/* find the max set of GPIOs */

Use one pattern for all comments, like "Capital letter first, and full words avoiding abbreviations".

Quoted 7 lines
drivers/mfd/f81504-core.c new file +6 -0
+		gpio_en = f0h_data | ~f3h_data;
+	}
+
+	switch (dev->device) {
+	case FINTEK_F81504: /* 4 ports */
+		/* F81504 max 2 sets of GPIO, others are max 6

sets*/

Space before * is needed.

Quoted 18 lines
drivers/mfd/f81504-core.c new file +13 -0
+		gpio_en &= 0x03;
+	case FINTEK_F81508: /* 8 ports */
+		max_port = dev->device & 0xff;
+		break;
+	case FINTEK_F81512: /* 12 ports */
+		max_port = 12;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* rewrite GPIO Mode setting */
+	pci_write_config_byte(dev, F81504_GPIO_ENABLE_REG, gpio_en &

0x3f);

drivers/mfd/f81504-core.c new file +1 -0
+	pci_write_config_byte(dev, F81504_GPIO_MODE_REG, ~gpio_en &

0x3f);

drivers/mfd/f81504-core.c new file +2 -0
+
+	/* Get the UART IO address dispatch from the BIOS */

drivers/mfd/f81504-core.c line 95

Quoted 10 lines
drivers/mfd/f81504-core.c new file +10 -0
+	pci_read_config_dword(dev, 0x24, &bar_data[0]);
+	pci_read_config_dword(dev, 0x20, &bar_data[1]);
+	pci_read_config_dword(dev, 0x1c, &bar_data[2]);
+
+	/* Compatible bit for newer step IC */
+	pci_read_config_word(dev, F81504_IRQSEL_REG, &tmp);
+	tmp |= BIT(8);
+	pci_write_config_word(dev, F81504_IRQSEL_REG, tmp);
+
+	for (i = 0; i < max_port; ++i) {

i++, since it's more usual pattern.

Quoted 21 lines
drivers/mfd/f81504-core.c new file +2 -0
+		/* UART0 configuration offset start from 0x40 */
+		config_base = F81504_UART_START_ADDR +

F81504_UART_OFFSET * i;

drivers/mfd/f81504-core.c new file +3 -0
+		is_gpio = false;
+
 
 
 
+		/* find every port to check is multi-function port?

*/

drivers/mfd/f81504-core.c new file +3 -0
+		for (j = 0; j < ARRAY_SIZE(fintek_gpio_mapping);
++j) {
+			if (fintek_gpio_mapping[j] != i || !(gpio_en

& BIT(j)))

drivers/mfd/f81504-core.c new file +4 -0
+				continue;
+
+			/*
+			 * This port is multi-function and enabled

as gpio

drivers/mfd/f81504-core.c new file +1 -0
+			 * mode. So we'll not configure it as serial

port.

drivers/mfd/f81504-core.c line 111

Quoted 4 lines
drivers/mfd/f81504-core.c new file +4 -0
+			 */
+			is_gpio = true;
+			break;
+		}

Looks like a separate function.

func()
{
 for () {
   if ()
    return X;
 }
 return Y;
}

Quoted 28 lines
drivers/mfd/f81504-core.c new file +3 -0
+
+		/*
+		 * If the serial port is setting to gpio mode, don't

init it.

drivers/mfd/f81504-core.c new file +1 -0
+		 * Disable the serial port for user-space

application to

drivers/mfd/f81504-core.c new file +5 -0
+		 * control.
+		 */
+		if (is_gpio) {
+			/* Disable current serial port */
+			pci_write_config_byte(dev, config_base +

0x00, 0x00);

drivers/mfd/f81504-core.c new file +5 -0
+			continue;
+		}
+
+		/* Calculate Real IO Port */
+		iobase = (bar_data[i / 4] & 0xffffffe0) + (i % 4) *

8;

drivers/mfd/f81504-core.c new file +3 -0
+
+		/* Enable UART I/O port */
+		pci_write_config_byte(dev, config_base + 0x00,

0x01);

drivers/mfd/f81504-core.c new file +3 -0
+
+		/* Select 128-byte FIFO and 8x FIFO threshold */
+		pci_write_config_byte(dev, config_base + 0x01,

0x33);

drivers/mfd/f81504-core.c line 135

Quoted 4 lines
drivers/mfd/f81504-core.c new file +4 -0
+
+		/* LSB UART */
+		pci_write_config_byte(dev, config_base + 0x04,
+				(u8)(iobase & 0xff));

Redundant explicit casting.

drivers/mfd/f81504-core.c line 139

Quoted 4 lines
drivers/mfd/f81504-core.c new file +4 -0
+
+		/* MSB UART */
+		pci_write_config_byte(dev, config_base + 0x05,
+				(u8)((iobase & 0xff00) >> 8));

Ditto.

And similar question, can it be written as a word?

drivers/mfd/f81504-core.c line 145

Quoted 8 lines
drivers/mfd/f81504-core.c new file +2 -0
+
+		pci_write_config_byte(dev, config_base + 0x06, dev-
Quoted 1 line

irq);

drivers/mfd/f81504-core.c new file +3 -0
+
+		/*
+		 * Force init to RS232 / Share Mode, recovery

previous mode

drivers/mfd/f81504-core.c new file +1 -0
+		 * will done in F81504 8250 platform driver resume()

Period at the end of sentences in multi-line comments.

Quoted 30 lines
drivers/mfd/f81504-core.c new file +2 -0
+		 */
+		pci_write_config_byte(dev, config_base + 0x07,

0x01);

drivers/mfd/f81504-core.c new file +6 -0
+	}
+
+	return 0;
+}
+
+static int f81504_prepage_serial_port(struct pci_dev *dev, int

max_port)

drivers/mfd/f81504-core.c new file +14 -0
+{
+	size_t i;
+	int status;
+	u8 tmp;
+	u16 iobase;
+	struct resource	resources = DEFINE_RES_IO(0, 0);
 
 
+	struct mfd_cell f81504_serial_cell = {
+		.name = F81504_SERIAL_NAME,
+		.num_resources	= 1,
+	};
 
+
+	for (i = 0; i < max_port; ++i) {
+		/* Check UART is enabled */
 
 
+		pci_read_config_byte(dev, F81504_UART_START_ADDR + i

*

drivers/mfd/f81504-core.c line 170

Quoted 3 lines
drivers/mfd/f81504-core.c new file +3 -0
+				F81504_UART_OFFSET, &tmp);
+		if (!tmp)
+			continue;

So, this is the same as below, right?

drivers/mfd/f81504-core.c line 174

Quoted 5 lines
drivers/mfd/f81504-core.c new file +3 -0
+
+		/* Get UART IO Address */
+		pci_read_config_word(dev, F81504_UART_START_ADDR + i

*

drivers/mfd/f81504-core.c new file +1 -0
+				F81504_UART_OFFSET + 4, &iobase);

…why not to check here?

drivers/mfd/f81504-core.c line 180

Quoted 7 lines
drivers/mfd/f81504-core.c new file +6 -0
+
+		resources.start = iobase;
+		resources.end = iobase + F81504_IO_REGION - 1;
+
+		f81504_serial_cell.resources = &resources;
 
+		f81504_serial_cell.pdata_size = sizeof(i);

This is static, can be part of definition.

drivers/mfd/f81504-core.c

Quoted 11 lines
drivers/mfd/f81504-core.c new file +3 -0
+		f81504_serial_cell.platform_data = &i;
+
+		status = mfd_add_devices(&dev->dev,

PLATFORM_DEVID_AUTO,

drivers/mfd/f81504-core.c new file +1 -0
+					&f81504_serial_cell, 1,

NULL, dev->irq,

drivers/mfd/f81504-core.c new file +3 -0
+					NULL);
+		if (status) {
+			dev_warn(&dev->dev, "%s: add device failed:

%d\n",

drivers/mfd/f81504-core.c new file +1 -0
+					__func__, status);

Indent _ under &.

Quoted 13 lines
drivers/mfd/f81504-core.c new file +13 -0
+			return status;
+		}
+	}
+
+	return 0;
+}
+
+static int f81504_prepage_gpiolib(struct pci_dev *dev)
+{
+	size_t i;
+	int status;
+	struct f81504_pci_private *priv = pci_get_drvdata(dev);
+	struct mfd_cell f81504_gpio_cell = {

drivers/mfd/f81504-core.c line 209

Quoted 10 lines
drivers/mfd/f81504-core.c new file +8 -0
+		.name = F81504_GPIO_NAME,
+	};
+
+	for (i = 0; i < ARRAY_SIZE(fintek_gpio_mapping); ++i) {
+		if (!(priv->gpio_en & BIT(i)))
+			continue;
+
 
 
+		f81504_gpio_cell.pdata_size = sizeof(i);

Static. The problem here is badly chosen type of i. Like I mentioned at the top of review…

Quoted 20 lines
drivers/mfd/f81504-core.c new file +3 -0
+		f81504_gpio_cell.platform_data = &i;
+
+		status = mfd_add_devices(&dev->dev,

PLATFORM_DEVID_AUTO,

drivers/mfd/f81504-core.c new file +1 -0
+					&f81504_gpio_cell, 1, NULL,

dev->irq,

drivers/mfd/f81504-core.c new file +3 -0
+					NULL);
+		if (status) {
+			dev_warn(&dev->dev, "%s: add device failed:

%d\n",

drivers/mfd/f81504-core.c new file +9 -0
+					__func__, status);
+			return status;
+		}
+	}
+
+	return 0;
+}
+
+static int f81504_probe(struct pci_dev *dev, const struct

pci_device_id

drivers/mfd/f81504-core.c line 226

Quoted 1 line
drivers/mfd/f81504-core.c new file +1 -0
+			*dev_id)

Usually drivers are using pdev, id pair in parameters. Shorter; known pattern.

drivers/mfd/f81504-core.c line 232

Quoted 6 lines
drivers/mfd/f81504-core.c new file +6 -0
+{
+	int status;
+	u8 tmp;
+	struct f81504_pci_private *priv;
+
+	status = pci_enable_device(dev);

Please, pcim_, see comment below.

drivers/mfd/f81504-core.c line 238

Quoted 6 lines
drivers/mfd/f81504-core.c new file +6 -0
+	if (status)
+		return status;
+
+	/* Init PCI Configuration Space */
+	status = f81504_port_init(dev);
+	if (status)

Device left enabled if not managed.

drivers/mfd/f81504-core.c line 243

Quoted 6 lines
drivers/mfd/f81504-core.c new file +3 -0
+		return status;
+
+	priv = devm_kzalloc(&dev->dev, sizeof(struct

f81504_pci_private),

drivers/mfd/f81504-core.c new file +2 -0
+				GFP_KERNEL);
+	if (!priv)

Ditto.

Quoted 6 lines
drivers/mfd/f81504-core.c new file +3 -0
+		return -ENOMEM;
+
+	/* Save the GPIO_ENABLE_REG after f81504_port_init() for

future use */

drivers/mfd/f81504-core.c new file +1 -0
+	pci_read_config_byte(dev, F81504_GPIO_ENABLE_REG, &priv-
Quoted 1 line

gpio_en);

drivers/mfd/f81504-core.c line 253

Quoted 8 lines
drivers/mfd/f81504-core.c new file +6 -0
+
+	/* Save GPIO IO Addr to private data */
 
 
+	pci_read_config_byte(dev, F81504_GPIO_IO_MSB_REG, &tmp);
+	priv->gpio_ioaddr = tmp << 8;
+	pci_read_config_byte(dev, F81504_GPIO_IO_LSB_REG, &tmp);
+	priv->gpio_ioaddr |= tmp;

One read as word?

Quoted 10 lines
drivers/mfd/f81504-core.c new file +5 -0
+
+	pci_set_drvdata(dev, priv);
+
+	/* Generate UART Ports */
+	status = f81504_prepage_serial_port(dev, dev_id-
Quoted 1 line

driver_data);

drivers/mfd/f81504-core.c new file +4 -0
+	if (status)
+		goto failed;
+
+	/* Generate GPIO Sets */

drivers/mfd/f81504-core.c line 270

Quoted 10 lines
drivers/mfd/f81504-core.c new file +8 -0
+	status = f81504_prepage_gpiolib(dev);
+	if (status)
+		goto failed;
+
+	return 0;
+
+failed:
 
 
+	mfd_remove_devices(&dev->dev);

mfd_add_devices takes care.

drivers/mfd/f81504-core.c

Quoted 1 line
drivers/mfd/f81504-core.c new file +1 -0
+	pci_disable_device(dev);

pcim_ takes case.

drivers/mfd/f81504-core.c line 278

Quoted 8 lines
drivers/mfd/f81504-core.c new file +7 -0
+	return status;
+}
+
+static void f81504_remove(struct pci_dev *dev)
+{
 
+	mfd_remove_devices(&dev->dev);
+	pci_disable_device(dev);

Ditto.

Quoted 8 lines
drivers/mfd/f81504-core.c new file +8 -0
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int f81504_suspend(struct device *dev)
+{
+	return 0;
+}
+

drivers/mfd/f81504-core.c line 294

Quoted 10 lines
drivers/mfd/f81504-core.c new file +8 -0
+static int f81504_resume(struct device *dev)
+{
+	int status;
+	struct pci_dev *pdev = to_pci_dev(dev);
+
 
 
+	status = pci_enable_device(pdev);
+	if (status)
+		return status;

It's done by PCI core I believe.

Quoted 6 lines
drivers/mfd/f81504-core.c new file +6 -0
+
+	/* Re-init PCI Configuration Space */
+	status = f81504_port_init(pdev);
+	if (status)
+		return status;
+

drivers/mfd/f81504-core.c line 310

Quoted 10 lines
drivers/mfd/f81504-core.c new file +10 -0
+	return 0;
+}
+#endif
+
+static const struct pci_device_id f81504_dev_table[] = {
+	/* Fintek PCI serial cards */
+	{PCI_DEVICE(FINTEK_VID, FINTEK_F81504), .driver_data = 4},
+	{PCI_DEVICE(FINTEK_VID, FINTEK_F81508), .driver_data = 8},
+	{PCI_DEVICE(FINTEK_VID, FINTEK_F81512), .driver_data = 12},
+	{}

So, if you have default y for this and 8250_pci, which one will be loaded?

Quoted 4 lines
drivers/mfd/f81504-core.c new file +3 -0
+};
+
+static SIMPLE_DEV_PM_OPS(f81504_pm_ops, f81504_suspend,

f81504_resume);

drivers/mfd/f81504-core.c line 321

Quoted 10 lines
drivers/mfd/f81504-core.c new file +8 -0
+
+static struct pci_driver f81504_driver = {
+	.name = F81504_DRIVER_NAME,
+	.probe = f81504_probe,
+	.remove = f81504_remove,
+	.driver		= {
+		.pm	= &f81504_pm_ops,
 
 
+		.owner	= THIS_MODULE,

kbuild  already complained about.

Quoted 16 lines
drivers/mfd/f81504-core.c new file +10 -0
+	},
+	.id_table = f81504_dev_table,
+};
+
+module_pci_driver(f81504_driver);
+
+MODULE_DEVICE_TABLE(pci, f81504_dev_table);
+MODULE_DESCRIPTION(F81504_DEV_DESC);
+MODULE_AUTHOR("Peter Hong <[email protected]>");
+MODULE_LICENSE("GPL");
include/linux/mfd/f81504.h new file +0 -0
new file mode 100644
index 0000000..13bd0ae

include/linux/mfd/f81504.h line 1

Quoted 1 line
include/linux/mfd/f81504.h new file +1 -0
@@ -0,0 +1,52 @@
+#ifndef __F81504_H__

__MFD_F…

Quoted 51 lines
include/linux/mfd/f81504.h new file +51 -0
+#define __F81504_H__
+
+#define FINTEK_VID			0x1c29
+#define FINTEK_F81504			0x1104
+#define FINTEK_F81508			0x1108
+#define FINTEK_F81512			0x1112
+
+#define FINTEK_MAX_PORT			12
+#define FINTEK_GPIO_NAME_LEN		32
+#define FINTEK_GPIO_DISPLAY		"GPIO"
+
+#define F81504_UART_START_ADDR		0x40
+#define F81504_UART_MODE_OFFSET		0x07
+#define F81504_UART_OFFSET		0x08
+
+/* RTS will control by MCR if this bit is 0 */
+#define F81504_RTS_CONTROL_BY_HW	BIT(4)
+/* only worked with FINTEK_RTS_CONTROL_BY_HW on */
+#define F81504_RTS_INVERT		BIT(5)
+
+#define F81504_CLOCK_RATE_MASK		0xc0
+#define F81504_CLKSEL_1DOT846_MHZ	0x00
+#define F81504_CLKSEL_18DOT46_MHZ	0x40
+#define F81504_CLKSEL_24_MHZ		0x80
+#define F81504_CLKSEL_14DOT77_MHZ	0xc0
+
+#define F81504_IRQSEL_REG		0xb8
+
+#define F81504_GPIO_ENABLE_REG		0xf0
+#define F81504_GPIO_IO_LSB_REG		0xf1
+#define F81504_GPIO_IO_MSB_REG		0xf2
+#define F81504_GPIO_MODE_REG		0xf3
+
+#define F81504_GPIO_START_ADDR		0xf8
+#define F81504_GPIO_OUT_EN_OFFSET	0x00
+#define F81504_GPIO_DRIVE_EN_OFFSET	0x01
+#define F81504_GPIO_SET_OFFSET		0x08
+
+#define F81504_GPIO_NAME		"f81504_gpio"
+#define F81504_SERIAL_NAME		"f81504_serial"
+#define F81504_MAX_GPIO_CNT		6
+
+extern const u8 fintek_gpio_mapping[F81504_MAX_GPIO_CNT];
+
+struct f81504_pci_private {
+	int line[FINTEK_MAX_PORT];
+	u8 gpio_en;
+	u16 gpio_ioaddr;
+	u32 uart_count, gpio_count;
+};
+#endif
Signature · 2 lines
Andy Shevchenko <[email protected]>
Intel Finland Oy
#14 lore raw

Re: [PATCH V2 2/4] gpio: gpio-f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO GPIOLIB support

In reply to Peter Hung
Quoted 21 lines · Peter Hung

This driver is GPIOLIB driver for F81504/508/512, it'll handle the GPIOLIB operation of this device. This module will depend on MFD_FINTEK_F81504_CORE.

(quoted diff) +2 -0
+	/*
+	 * The GPIO default driven mode for this device is open-

drain. The

(quoted diff) +1 -0
+	 * GPIOLIB had no change GPIO mode API currently. So we

leave the

drivers/gpio/gpio-f81504.c new file +3 -0
+	 * Push-Pull code below.
+	 *
+	 * pci_read_config_byte(dev, GPIO_START_ADDR + idx *

GPIO_SET_OFFSET +

(quoted diff) +2 -0
+	 *			GPIO_DRIVE_EN_OFFSET, &tmp);
+	 * pci_write_config_byte(dev, GPIO_START_ADDR + idx *

GPIO_SET_OFFSET +

(quoted diff) +1 -0
+	 *			GPIO_DRIVE_EN_OFFSET, tmp |

BIT(gpio_num));

drivers/gpio/gpio-f81504.c line 89

Quoted 4 lines
drivers/gpio/gpio-f81504.c new file +4 -0
+	 */
+
+	/* set output data */
+	tmp = inb(priv->gpio_ioaddr + gc->idx);

ioread8 is a bit better since it automatically works with IO space and MMIO. But if you are certain you will always have the address in IO space, you can disregard this comment.

Quoted 12 lines
drivers/gpio/gpio-f81504.c new file +10 -0
+static int f81504_gpio_probe(struct platform_device *pdev)
+{
+	int status;
+	struct f81504_gpio_chip *gc;
+	void *data = dev_get_platdata(&pdev->dev);
+	u8 gpio_idx = *(u8 *)data;
+	char *name;
+
+	if (gpio_idx >= ARRAY_SIZE(fintek_gpio_mapping)) {
+		dev_err(&pdev->dev, "%s: gpio_idx:%d out of

range.\n",

drivers/gpio/gpio-f81504.c new file +1 -0
+				__func__, gpio_idx);

drivers/gpio/gpio-f81504.c line 198

Quoted 10 lines
drivers/gpio/gpio-f81504.c new file +8 -0
+		return -ENODEV;
+	}
+
+	gc = devm_kzalloc(&pdev->dev, sizeof(*gc), GFP_KERNEL);
+	if (!gc)
+		return -ENOMEM;
+
 
 
+	kfree(data);

What the heck?

Quoted 30 lines
drivers/gpio/gpio-f81504.c new file +4 -0
+	mutex_init(&gc->locker);
+	platform_set_drvdata(pdev, gc);
+
+	name = devm_kzalloc(&pdev->dev, FINTEK_GPIO_NAME_LEN,

GFP_KERNEL);

drivers/gpio/gpio-f81504.c new file +22 -0
+	if (!name)
+		return -ENOMEM;
+
+	/* This will display like as GPIO-1x */
+	sprintf(name, "%s-%dx", FINTEK_GPIO_DISPLAY, gpio_idx);
+
+	gc->chip.owner = THIS_MODULE;
+	gc->chip.label = name;
+	gc->chip.ngpio = 8;
+	gc->chip.dev = &pdev->dev;
+	gc->chip.get = f81504_gpio_get;
+	gc->chip.set = f81504_gpio_set;
+	gc->chip.direction_input = f81504_gpio_direction_in;
+	gc->chip.direction_output = f81504_gpio_direction_out;
+	gc->chip.get_direction = f81504_gpio_get_direction;
+	gc->chip.can_sleep = 1;
+	gc->chip.base = -1;
+	gc->idx = gpio_idx;
+
 
 
+	status = gpiochip_add(&gc->chip);
+	if (status) {
+		dev_err(&pdev->dev, "%s: gpiochip_add failed: %d\n",

__func__,

drivers/gpio/gpio-f81504.c line 226

Quoted 2 lines
drivers/gpio/gpio-f81504.c new file +2 -0
+				status);
+		return -ENOMEM;

You ignored the status.

drivers/gpio/gpio-f81504.c line 55

Quoted 3 lines
drivers/gpio/gpio-f81504.c new file +3 -0
+	}
+
+	return 0;

Perhaps just
return gpiochip_add(); ?

Quoted 28 lines
drivers/gpio/gpio-f81504.c new file +28 -0
+}
+
+static int f81504_gpio_remove(struct platform_device *pdev)
+{
+	struct f81504_gpio_chip *gc = platform_get_drvdata(pdev);
+
+	gpiochip_remove(&gc->chip);
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(f81504_gpio_pm_ops, f81504_gpio_suspend,
+		f81504_gpio_resume);
+
+static struct platform_driver f81504_gpio_driver = {
+	.driver = {
+		.name	= F81504_GPIO_NAME,
+		.owner	= THIS_MODULE,
+		.pm     = &f81504_gpio_pm_ops,
+	},
+	.probe		= f81504_gpio_probe,
+	.remove		= f81504_gpio_remove,
+};
+
+module_platform_driver(f81504_gpio_driver);
+
+MODULE_AUTHOR("Peter Hong <[email protected]>");
+MODULE_DESCRIPTION("Fintek F81504/508/512 PCIE GPIOLIB driver");
+MODULE_LICENSE("GPL");
Signature · 2 lines
Andy Shevchenko <[email protected]>
Intel Finland Oy
#23 lore raw

Re: [PATCH V2 4/4] serial: 8250_pci: Remove Fintek F81504/508/512 UART driver

In reply to Peter Hung
Quoted 15 lines · Peter Hung

Remove Fintek F81504/508/512 PCIE-to-UART device driver from 8250_pci.c

Paul recommed us do less code deletion to avoid confusing problem when
bisect.
https://lkml.org/lkml/2016/1/18/646

drivers/tty/serial/8250/8250_pci.c +0 -4
-	/* Fintek PCI serial cards */
-	{ PCI_DEVICE(0x1c29, 0x1104), .driver_data = pbn_fintek_4 },
-	{ PCI_DEVICE(0x1c29, 0x1108), .driver_data = pbn_fintek_8 },
-	{ PCI_DEVICE(0x1c29, 0x1112), .driver_data = pbn_fintek_12
Quoted 1 line

},

Shouldn't you blacklist them in 8250_pci?

Signature · 2 lines
Andy Shevchenko <[email protected]>
Intel Finland Oy
author
#3 lore raw

Re: [PATCH V2 1/4] mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

In reply to One Thousand Gnomes

Hi Alan,

One Thousand Gnomes 於 2016/1/28 下午 06:04 寫道:

Quoted 4 lines
Quoted 1 line

+ Please bulit-in kernel if you need early console support.

This driver needs to be built into the kernel to use early console support.

ok

Quoted 10 lines

drivers/mfd/f81504-core.c line 72

Quoted 6 lines
drivers/mfd/f81504-core.c new file +6 -0
+	switch (dev->device) {
+	case FINTEK_F81504: /* 4 ports */
+		/* F81504 max 2 sets of GPIO, others are max 6 sets*/
+		gpio_en &= 0x03;
+	case FINTEK_F81508: /* 8 ports */
+		max_port = dev->device & 0xff;

If that is meant to fall through from F81504 into F81508 it's worth commenting, otherwise someone reviewing the code can't always be sure it was intentional.

ok, I'll add comments to describe this.

Quoted 11 lines

drivers/mfd/f81504-core.c line 88

Quoted 4 lines
drivers/mfd/f81504-core.c new file +4 -0
+	/* Get the UART IO address dispatch from the BIOS */
+	pci_read_config_dword(dev, 0x24, &bar_data[0]);
+	pci_read_config_dword(dev, 0x20, &bar_data[1]);
+	pci_read_config_dword(dev, 0x1c, &bar_data[2]);

Take these from the pci device itself. On some non PC platforms the values in the pci bar may be remapped by bridges and not give you the true answer.

pci_resource_start(dev, barnumber)

Thanks for point this out, I'll rewrite here with pci_resource_start().

Signature · 2 lines
With Best Regards,
Peter Hung
author
#5 lore raw

Re: [PATCH V2 1/4] mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

In reply to Andy Shevchenko

Hi Andy,

Andy Shevchenko 於 2016/1/28 下午 07:55 寫道:

Quoted 4 lines
Quoted 1 line

+ default y

I'm not sure we have to have this always y. Perhaps default SERIAL_8250_PCI

Your comment is right, this device major function is serial port. GPIO maybe not enabled by H/W manufacturer.

I'll set it default with SERIAL_8250_PCI.

Quoted 5 lines
Quoted 1 line

+obj-$(CONFIG_MFD_FINTEK_F81504_CORE) += f81504-core.o

I think '_' is better than '-'. What I saw and usually do is '_' for regular source modules and '-' for the resulting objects when they have more than one file.

I used f81504_core.c originally, but I found most of files are named xxx-ooo.c when I try to modify makefile. Should I change it to f81504_core.c ??

Quoted 4 lines
Quoted 2 lines

+#define F81504_DEV_DESC "Fintek F81504/508/512 PCIE-
to-UART core"

Do you need this definition? Is it used more than once?

ok, I'll direct use the string without define.

Quoted 13 lines

drivers/mfd/f81504-core.c line 27

Quoted 9 lines
drivers/mfd/f81504-core.c new file +9 -0
+static int f81504_port_init(struct pci_dev *dev)
+{
+	size_t i, j;
+	u32 max_port, iobase, gpio_addr;
+	u32 bar_data[3];
+	u16 tmp;
+	u8 config_base, gpio_en, f0h_data, f3h_data;
+	bool is_gpio;
+	struct f81504_pci_private *priv = pci_get_drvdata(dev);

I would suggest to rearrange definition block here (and in the rest of the functions in entire series) to somehow follow the following pattern

Quoted 7 lines

1) assignments go first, especially container_of() based ones;
2) group variables by meaning and put longer lines upper;
3) return value variable, if exists, goes last.

Besides that choose types carefully. If there is known limit for counters, no need to define wider type than needed. Use proper types for corresponding values.

I'll try to rearrange the definition blocks.
For the counter issue, some senior recommend me to change count from int to size_t for performance. In this case, should I use u8 to replace i & j ? It should be less than 12 & 6.

Quoted 6 lines
Quoted 4 lines
drivers/mfd/f81504-core.c new file +4 -0
+
+	/* Init GPIO IO Address */
+	pci_read_config_dword(dev, 0x18, &gpio_addr);
+	gpio_addr &= 0xffffffe0;
Quoted 7 lines

drivers/mfd/f81504-core.c line 34

Quoted 5 lines
(quoted diff) +1 -0
+	pci_write_config_byte(dev, F81504_GPIO_IO_LSB_REG, gpio_addr

& 0xff);

(quoted diff) +1 -0
+	pci_write_config_byte(dev, F81504_GPIO_IO_MSB_REG,

(gpio_addr >> 8) &

drivers/mfd/f81504-core.c new file +1 -0
+			0xff);

Could it be written at once as a word?

I tested with writing a word to "F81504_GPIO_IO_LSB_REG", but it'll failed, so I'll remain it.

Quoted 9 lines

drivers/mfd/f81504-core.c line 54

Quoted 6 lines
(quoted diff) +2 -0
+	if (priv) {
+		/* Reinit from resume(), read the previous value

from priv */

drivers/mfd/f81504-core.c new file +1 -0
+		gpio_en = priv->gpio_en;

I would suggest to move this line down to follow same pattern in else branch.

The f81504_port_init() will be called probe()/resume().

We'll initialize gpio_en = (f0h | ~f3h) and save it in private data when probe(), reload gpio_en from private data when resume().

The F81504/508/512 can be used EEPROM to override F0h/F3h on power on. Some motherboard designer will put the IC on board and want to cost down EEPROM. They will setting F0/F3h with ASL code, but without EEPROM , the IC back from resume() will get F0/F3h with 0x00, so we should save gpio_en when probe(), and restore it when resume().

Quoted 5 lines

Review

Quoted 2 lines
(quoted diff) +2 -0
+
+		/* re-save GPIO IO addr for called by resume() */

re-save -> Re-save
addr -> address

ok

Quoted 4 lines
Quoted 4 lines
drivers/mfd/f81504-core.c new file +4 -0
+		priv->gpio_ioaddr = gpio_addr;
+	} else {
+		/* Driver first init */
+		pci_read_config_byte(dev, F81504_GPIO_ENABLE_REG,
Quoted 8 lines

Review

Quoted 5 lines

&f0h_data);

(quoted diff) +1 -0
+		pci_read_config_byte(dev, F81504_GPIO_MODE_REG,

&f3h_data);

(quoted diff) +2 -0
+
+		/* find the max set of GPIOs */

Use one pattern for all comments, like "Capital letter first, and full words avoiding abbreviations".

ok

Quoted 5 lines
Quoted 3 lines
(quoted diff) +2 -0
+	case FINTEK_F81504: /* 4 ports */
+		/* F81504 max 2 sets of GPIO, others are max 6

sets*/

Space before * is needed.

ok

Quoted 3 lines

Review

Quoted 1 line
(quoted diff) +1 -0
+	for (i = 0; i < max_port; ++i) {

i++, since it's more usual pattern.

ok

Quoted 20 lines
Quoted 13 lines
(quoted diff) +1 -0
+		/* find every port to check is multi-function port?

*/

(quoted diff) +3 -0
+		for (j = 0; j < ARRAY_SIZE(fintek_gpio_mapping);
++j) {
+			if (fintek_gpio_mapping[j] != i || !(gpio_en

& BIT(j)))

drivers/mfd/f81504-core.c new file +4 -0
+				continue;
+
+			/*
+			 * This port is multi-function and enabled

as gpio

(quoted diff) +1 -0
+			 * mode. So we'll not configure it as serial

port.

drivers/mfd/f81504-core.c line 111

Quoted 4 lines
drivers/mfd/f81504-core.c new file +4 -0
+			 */
+			is_gpio = true;
+			break;
+		}

Looks like a separate function.

Quoted 8 lines

func()
{

  for () {
    if ()
     return X;

}
return Y;
}

ok.

Quoted 9 lines

drivers/mfd/f81504-core.c line 135

Quoted 7 lines
(quoted diff) +2 -0
+		/* Select 128-byte FIFO and 8x FIFO threshold */
+		pci_write_config_byte(dev, config_base + 0x01,

0x33);

drivers/mfd/f81504-core.c new file +4 -0
+
+		/* LSB UART */
+		pci_write_config_byte(dev, config_base + 0x04,
+				(u8)(iobase & 0xff));

Redundant explicit casting.

ok

Quoted 8 lines

drivers/mfd/f81504-core.c line 139

Quoted 4 lines
drivers/mfd/f81504-core.c new file +4 -0
+
+		/* MSB UART */
+		pci_write_config_byte(dev, config_base + 0x05,
+				(u8)((iobase & 0xff00) >> 8));

Ditto.

And similar question, can it be written as a word?

Here can be written with a word, I'll rewrite it.

Quoted 10 lines

drivers/mfd/f81504-core.c line 145

Quoted 8 lines
(quoted diff) +2 -0
+
+		pci_write_config_byte(dev, config_base + 0x06, dev-
Quoted 1 line

irq);

drivers/mfd/f81504-core.c new file +3 -0
+
+		/*
+		 * Force init to RS232 / Share Mode, recovery

previous mode

drivers/mfd/f81504-core.c new file +1 -0
+		 * will done in F81504 8250 platform driver resume()

Period at the end of sentences in multi-line comments.

Sorry, what this mean for ?
I cant use multi-line comments in the end ??

Quoted 12 lines

drivers/mfd/f81504-core.c line 170

Quoted 9 lines
(quoted diff) +3 -0
+	for (i = 0; i < max_port; ++i) {
+		/* Check UART is enabled */
 
 
+		pci_read_config_byte(dev, F81504_UART_START_ADDR + i

*

drivers/mfd/f81504-core.c new file +3 -0
+				F81504_UART_OFFSET, &tmp);
+		if (!tmp)
+			continue;

So, this is the same as below, right?

Quoted 7 lines

drivers/mfd/f81504-core.c line 174

Quoted 5 lines
drivers/mfd/f81504-core.c new file +3 -0
+
+		/* Get UART IO Address */
+		pci_read_config_word(dev, F81504_UART_START_ADDR + i

*

drivers/mfd/f81504-core.c new file +1 -0
+				F81504_UART_OFFSET + 4, &iobase);

…why not to check here?

It's a bit difference, this section will check if UART enabled (tmp). It'll generate platform device and get IO address when tmp != 0. If tmp = 0, skip this idx, dont need to get current IO address and try with next.

Quoted 3 lines

drivers/mfd/f81504-core.c line 180

Quoted 1 line
drivers/mfd/f81504-core.c new file +1 -0
+		f81504_serial_cell.pdata_size = sizeof(i);

This is static, can be part of definition.

ok

Quoted 5 lines
Quoted 5 lines
drivers/mfd/f81504-core.c new file +3 -0
+		f81504_serial_cell.platform_data = &i;
+
+		status = mfd_add_devices(&dev->dev,

PLATFORM_DEVID_AUTO,

(quoted diff) +1 -0
+					&f81504_serial_cell, 1,
Quoted 8 lines

Review

Quoted 6 lines

NULL, dev->irq,

drivers/mfd/f81504-core.c new file +3 -0
+					NULL);
+		if (status) {
+			dev_warn(&dev->dev, "%s: add device failed:

%d\n",

(quoted diff) +1 -0
+					__func__, status);

Indent _ under &.

Some senior recommend me to do at least 2-tabs to do indent when code cross multi-line. So I'll use to 2-tabs from "dev" to do indent. How should I do with indent ?? It seems no consensus, but Lindent will do indent like your comments.

Quoted 5 lines

drivers/mfd/f81504-core.c line 209

Quoted 2 lines
drivers/mfd/f81504-core.c new file +1 -0
+		f81504_gpio_cell.pdata_size = sizeof(i);

Static. The problem here is badly chosen type of i. Like I mentioned at the top of review…

I'll try to rewrite it with pass a structure. It seems more make sense.

Quoted 6 lines

drivers/mfd/f81504-core.c line 226

Quoted 3 lines

+static int f81504_probe(struct pci_dev *dev, const struct pci_device_id

drivers/mfd/f81504-core.c new file +1 -0
+			*dev_id)

Usually drivers are using pdev, id pair in parameters. Shorter; known pattern.

ok.

Quoted 16 lines

drivers/mfd/f81504-core.c line 232

Quoted 6 lines
drivers/mfd/f81504-core.c new file +6 -0
+{
+	int status;
+	u8 tmp;
+	struct f81504_pci_private *priv;
+
+	status = pci_enable_device(dev);

Please, pcim_, see comment below.

drivers/mfd/f81504-core.c line 238

Quoted 6 lines
drivers/mfd/f81504-core.c new file +6 -0
+	if (status)
+		return status;
+
+	/* Init PCI Configuration Space */
+	status = f81504_port_init(dev);
+	if (status)

Device left enabled if not managed.

Quoted 8 lines

drivers/mfd/f81504-core.c line 243

Quoted 6 lines
drivers/mfd/f81504-core.c new file +3 -0
+		return status;
+
+	priv = devm_kzalloc(&dev->dev, sizeof(struct

f81504_pci_private),

drivers/mfd/f81504-core.c new file +2 -0
+				GFP_KERNEL);
+	if (!priv)

Ditto.

ok, I'll rewrite it with managed type.

Quoted 10 lines
Quoted 9 lines
drivers/mfd/f81504-core.c new file +3 -0
+		return -ENOMEM;
+
+	/* Save the GPIO_ENABLE_REG after f81504_port_init() for

future use */

(quoted diff) +1 -0
+	pci_read_config_byte(dev, F81504_GPIO_ENABLE_REG, &priv-
Quoted 1 line

gpio_en);

(quoted diff) +2 -0
+
+	/* Save GPIO IO Addr to private data */
Quoted 6 lines

drivers/mfd/f81504-core.c line 253

Quoted 4 lines
drivers/mfd/f81504-core.c new file +4 -0
+	pci_read_config_byte(dev, F81504_GPIO_IO_MSB_REG, &tmp);
+	priv->gpio_ioaddr = tmp << 8;
+	pci_read_config_byte(dev, F81504_GPIO_IO_LSB_REG, &tmp);
+	priv->gpio_ioaddr |= tmp;

One read as word?

It can't read as word. The "F81504_GPIO_IO_LSB_REG" is 0xf1, It seems can't be read word/dword from a odd address.

I'll remain it.

Quoted 7 lines

Review

Quoted 1 line
(quoted diff) +1 -0
+	mfd_remove_devices(&dev->dev);

mfd_add_devices takes care.

Review

Quoted 1 line
(quoted diff) +1 -0
+	pci_disable_device(dev);

pcim_ takes case.

ok

Quoted 10 lines

drivers/mfd/f81504-core.c line 278

Quoted 8 lines
drivers/mfd/f81504-core.c new file +7 -0
+	return status;
+}
+
+static void f81504_remove(struct pci_dev *dev)
+{
 
+	mfd_remove_devices(&dev->dev);
+	pci_disable_device(dev);

Ditto.

ok

Quoted 10 lines

drivers/mfd/f81504-core.c line 294

Quoted 8 lines
drivers/mfd/f81504-core.c new file +8 -0
+static int f81504_resume(struct device *dev)
+{
+	int status;
+	struct pci_dev *pdev = to_pci_dev(dev);
+
+	status = pci_enable_device(pdev);
+	if (status)
+		return status;

It's done by PCI core I believe.

ok

Quoted 9 lines

drivers/mfd/f81504-core.c line 310

Quoted 6 lines
drivers/mfd/f81504-core.c new file +6 -0
+static const struct pci_device_id f81504_dev_table[] = {
+	/* Fintek PCI serial cards */
+	{PCI_DEVICE(FINTEK_VID, FINTEK_F81504), .driver_data = 4},
+	{PCI_DEVICE(FINTEK_VID, FINTEK_F81508), .driver_data = 8},
+	{PCI_DEVICE(FINTEK_VID, FINTEK_F81512), .driver_data = 12},
+	{}

So, if you have default y for this and 8250_pci, which one will be loaded?

I had tested on x86, It'll handle by 8250_pci.c when this & 8250_pci.c all built-in mode.

BTW, due to the series patches across 3 subsystems MFD/GPIO/8250. I make the series patches under MFD subsystem, but the buildbot report git repository conflict with GPIO & 8250 (patch 2 & 3).

Should I split the series patches into 3 independent patch and based on their maintainer git repository?

Quoted 11 lines

drivers/mfd/f81504-core.c line 321

Quoted 9 lines
drivers/mfd/f81504-core.c new file +7 -0
+static struct pci_driver f81504_driver = {
+	.name = F81504_DRIVER_NAME,
+	.probe = f81504_probe,
+	.remove = f81504_remove,
+	.driver		= {
+		.pm	= &f81504_pm_ops,
 
 
+		.owner	= THIS_MODULE,

kbuild already complained about.

ok

Quoted 9 lines

include/linux/mfd/f81504.h line 1

Quoted 7 lines
include/linux/mfd/f81504.h new file +1 -0
new file mode 100644
index 0000000..13bd0ae
@@ -0,0 +1,52 @@
+#ifndef __F81504_H__

__MFD_F…

ok

Thanks for your advices

Signature · 2 lines
With Best Regards,
Peter Hung
author
#15 lore raw

Re: [PATCH V2 2/4] gpio: gpio-f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO GPIOLIB support

In reply to Andy Shevchenko

Hi Andy,

Andy Shevchenko 於 2016/1/28 下午 08:03 寫道:

Quoted 7 lines · Peter Hung

Review

Quoted 2 lines
(quoted diff) +2 -0
+	/* set output data */
+	tmp = inb(priv->gpio_ioaddr + gc->idx);

ioread8 is a bit better since it automatically works with IO space and MMIO. But if you are certain you will always have the address in IO space, you can disregard this comment.

I had only tested on x86 environment currently. We'll try to get an ARM platform with PCIE to test it. We'll remain it until getting new board.

Quoted 21 lines
Quoted 20 lines
drivers/gpio/gpio-f81504.c new file +10 -0
+static int f81504_gpio_probe(struct platform_device *pdev)
+{
+	int status;
+	struct f81504_gpio_chip *gc;
+	void *data = dev_get_platdata(&pdev->dev);
+	u8 gpio_idx = *(u8 *)data;
+	char *name;
+
+	if (gpio_idx >= ARRAY_SIZE(fintek_gpio_mapping)) {
+		dev_err(&pdev->dev, "%s: gpio_idx:%d out of

range.\n",

drivers/gpio/gpio-f81504.c new file +8 -0
+				__func__, gpio_idx);
+		return -ENODEV;
+	}
+
+	gc = devm_kzalloc(&pdev->dev, sizeof(*gc), GFP_KERNEL);
+	if (!gc)
+		return -ENOMEM;
+
Quoted 3 lines

drivers/gpio/gpio-f81504.c line 198

Quoted 1 line
drivers/gpio/gpio-f81504.c new file +1 -0
+	kfree(data);

What the heck?

Sorry for the big mistake, I'd confused for dev_get_platdata() & platform_set_drvdata(). I'll rewrite this and check 8250_f81504.c too.

Quoted 9 lines

drivers/gpio/gpio-f81504.c line 226

Quoted 6 lines
drivers/gpio/gpio-f81504.c new file +3 -0
+	status = gpiochip_add(&gc->chip);
+	if (status) {
+		dev_err(&pdev->dev, "%s: gpiochip_add failed: %d\n",

__func__,

drivers/gpio/gpio-f81504.c new file +2 -0
+				status);
+		return -ENOMEM;

You ignored the status.

Quoted 6 lines

drivers/gpio/gpio-f81504.c line 55

Quoted 3 lines
drivers/gpio/gpio-f81504.c new file +3 -0
+	}
+
+	return 0;

Perhaps just
return gpiochip_add(); ?

Just return gpiochip_add() seems good.

Thanks your advices

Signature · 6 lines
With Best Regards,
Peter Hung
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#24 lore raw

Re: [PATCH V2 4/4] serial: 8250_pci: Remove Fintek F81504/508/512 UART driver

In reply to Andy Shevchenko

Hi Andy,

Andy Shevchenko 於 2016/1/28 下午 08:04 寫道:

Quoted 9 lines · Peter Hung
Quoted 5 lines
drivers/tty/serial/8250/8250_pci.c +0 -4
-	/* Fintek PCI serial cards */
-	{ PCI_DEVICE(0x1c29, 0x1104), .driver_data = pbn_fintek_4 },
-	{ PCI_DEVICE(0x1c29, 0x1108), .driver_data = pbn_fintek_8 },
-	{ PCI_DEVICE(0x1c29, 0x1112), .driver_data = pbn_fintek_12

},

Shouldn't you blacklist them in 8250_pci?

You are referring to add blacklist instead of remove F81504/508/512 code? or add blacklist and remove code?

Signature · 6 lines
With Best Regards,
Peter Hung
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#6 lore raw

Re: [PATCH V2 1/4] mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

In reply to Peter Hung
Quoted 9 lines · Peter Hung
Quoted 5 lines
Quoted 1 line

+obj-$(CONFIG_MFD_FINTEK_F81504_CORE) += f81504-core.o

I think '_' is better than '-'. What I saw and usually do is '_' for regular source modules and '-' for the resulting objects when they have more than one file.

I used f81504_core.c originally, but I found most of files are named xxx-ooo.c when I try to modify makefile. Should I change it to f81504_core.c ??

I prefer '-' in MFD.

Quoted 6 lines
Quoted 4 lines
Quoted 2 lines

+#define F81504_DEV_DESC "Fintek F81504/508/512 PCIE-
to-UART core"

Do you need this definition? Is it used more than once?

ok, I'll direct use the string without define.

Please rid all of the {DEV_NAME,DEV_DEC} defines, they only serve to obfuscate code.

Signature · 8 lines
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#25 lore raw

Re: [PATCH V2 4/4] serial: 8250_pci: Remove Fintek F81504/508/512 UART driver

In reply to Peter Hung
Quoted 16 lines · Peter Hung

Hi Andy,

Andy Shevchenko 於 2016/1/28 下午 08:04 寫道:

Quoted 12 lines · Peter Hung
Quoted 8 lines
(quoted diff) +0 -2
-	/* Fintek PCI serial cards */
-	{ PCI_DEVICE(0x1c29, 0x1104), .driver_data =

pbn_fintek_4 },

(quoted diff) +0 -1
-	{ PCI_DEVICE(0x1c29, 0x1108), .driver_data =

pbn_fintek_8 },

(quoted diff) +0 -1
-	{ PCI_DEVICE(0x1c29, 0x1112), .driver_data =

pbn_fintek_12
},

Shouldn't you blacklist them in 8250_pci?

Quoted 2 lines

You are referring to add blacklist instead of remove F81504/508/512 code?

No.

Quoted 1 line

or add blacklist and remove code?

This one.

Check what lspci tells you about your device. I'm pretty sure that it has Serial Class, which would trigger enumeration in 8250_pci.c if it comes first.

Signature · 7 lines
Andy Shevchenko <[email protected]>
Intel Finland Oy

--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#7 lore raw

Re: [PATCH V2 1/4] mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

In reply to Lee Jones

Thin out Cc list since mostly off topic message here.

Quoted 1 line · Lee Jones

I prefer '-' in MFD.

Have to memorize that.

/* A bit of off topic */
I will cook and send one patch regarding to Intel Quark SoC, i.e. UART driver, but I'm not sure it's a good idea now to use there - since there are already too many intel_ files with _ including existing drivers for Quark.

What do you think?

Signature · 2 lines
Andy Shevchenko <[email protected]>
Intel Finland Oy
#9 lore raw

Re: [PATCH V2 1/4] mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

In reply to Peter Hung
Quoted 27 lines · Peter Hung

Andy Shevchenko 於 2016/1/28 下午 07:55 寫道:

Quoted 1 line
Quoted 1 line

+obj-$(CONFIG_MFD_FINTEK_F81504_CORE) += f81504-core.o

+static int f81504_port_init(struct pci_dev *dev)

Quoted 14 lines

drivers/mfd/f81504-core.c line 27

Quoted 8 lines
drivers/mfd/f81504-core.c new file +8 -0
+{
+	size_t i, j;
+	u32 max_port, iobase, gpio_addr;
+	u32 bar_data[3];
+	u16 tmp;
+	u8 config_base, gpio_en, f0h_data, f3h_data;
+	bool is_gpio;
+	struct f81504_pci_private *priv = pci_get_drvdata(dev);

I would suggest to rearrange definition block here (and in the rest of
the functions in entire series) to somehow follow the following pattern

Quoted 8 lines

1) assignments go first, especially container_of() based ones;
2) group variables by meaning and put longer lines upper;
3) return value variable, if exists, goes last.

Besides that choose types carefully. If there is known limit for counters, no need to define wider type than needed. Use proper types
for corresponding values.

Quoted 6 lines

I'll try to rearrange the definition blocks.

For the counter issue, some senior recommend me to change count from int
to size_t for performance.

Wow, how come? On which arch?

Also mark this as (1) to refer below.

Quoted 2 lines

In this case, should I use u8 to replace
i & j ? It should be less than 12 & 6.

At least you tell compiler that it may use any suitable type. In any case the last decision is by compiler if you don't do any tricks.

So, I suggest to use non-fixed width type like (unsigned) int and leave everything else on compiler.

Quoted 15 lines
Quoted 6 lines
Quoted 4 lines
drivers/mfd/f81504-core.c new file +4 -0
+
+	/* Init GPIO IO Address */
+	pci_read_config_dword(dev, 0x18, &gpio_addr);
+	gpio_addr &= 0xffffffe0;
Quoted 8 lines

drivers/mfd/f81504-core.c line 34

Quoted 6 lines
(quoted diff) +1 -0
+	pci_write_config_byte(dev, F81504_GPIO_IO_LSB_REG,

gpio_addr
& 0xff);

(quoted diff) +1 -0
+	pci_write_config_byte(dev, F81504_GPIO_IO_MSB_REG,

(gpio_addr >> 8) &

drivers/mfd/f81504-core.c new file +1 -0
+			0xff);

Could it be written at once as a word?

Quoted 2 lines

I tested with writing a word to "F81504_GPIO_IO_LSB_REG", but it'll failed, so I'll remain it.

Please, add a comment line above.

Quoted 11 lines
Quoted 11 lines

drivers/mfd/f81504-core.c line 54

Quoted 7 lines
(quoted diff) +2 -0
+	if (priv) {
+		/* Reinit from resume(), read the previous value

from priv */

drivers/mfd/f81504-core.c new file +1 -0
+		gpio_en = priv->gpio_en;

I would suggest to move this line down to follow same pattern in else
branch.

I'm talking here to make simple rearrangement like

if () {
 …
 gpio_en = …
} else {
…
 gpio_en = …
}

Thus the gpio_en assignment goes last in both branches.

Quoted 13 lines
Quoted 4 lines
Quoted 4 lines
(quoted diff) +2 -0
+
+		pci_write_config_byte(dev, config_base + 0x06,

dev-

Quoted 1 line

irq);

Quoted 8 lines
Quoted 6 lines
drivers/mfd/f81504-core.c new file +3 -0
+
+		/*
+		 * Force init to RS232 / Share Mode, recovery

previous mode

(quoted diff) +1 -0
+		 * will done in F81504 8250 platform driver

resume()

Period at the end of sentences in multi-line comments.

Quoted 2 lines

Sorry, what this mean for ?
I cant use multi-line comments in the end ??

Sentences are started with capital letters and end with period '.' character, like this one.

Quoted 23 lines
Quoted 13 lines

drivers/mfd/f81504-core.c line 170

Quoted 10 lines
(quoted diff) +4 -0
+	for (i = 0; i < max_port; ++i) {
+		/* Check UART is enabled */
 
 
+		pci_read_config_byte(dev, F81504_UART_START_ADDR
+ i

*

drivers/mfd/f81504-core.c new file +3 -0
+				F81504_UART_OFFSET, &tmp);
+		if (!tmp)
+			continue;

So, this is the same as below, right?

Quoted 9 lines
Quoted 7 lines
drivers/mfd/f81504-core.c new file +4 -0
+
+		/* Get UART IO Address */
+		pci_read_config_word(dev, F81504_UART_START_ADDR
+ i

*

(quoted diff) +1 -0
+				F81504_UART_OFFSET + 4,

&iobase);

…why not to check here?

Quoted 4 lines

It's a bit difference, this section will check if UART enabled (tmp). It'll generate platform device and get IO address when tmp != 0. If tmp = 0, skip this idx, dont need to get current IO address and try with next.

Yeah, I missed that the offset is different.

Quoted 8 lines
(quoted diff) +1 -0
+		if (status) {
Quoted 6 lines

Review

Quoted 4 lines
(quoted diff) +1 -0
+			dev_warn(&dev->dev, "%s: add device

failed:
%d\n",

(quoted diff) +1 -0
+					__func__, status);

Indent _ under &.

Quoted 5 lines

Some senior recommend me to do at least 2-tabs to do indent when code cross multi-line. So I'll use to 2-tabs from "dev" to do indent.

How should I do with indent ?? It seems no consensus, but Lindent will do indent like your comments.

I would suggest to use what is used in most recent drivers and modules. I don't remember that 2 tabs fact is somehow reflected in CodingStyle.

Maybe your seniour was talkin about multi-line function definition?

Quoted 8 lines
drivers/mfd/f81504-core.c new file +1 -0
+		f81504_gpio_cell.pdata_size = sizeof(i);
Quoted 4 lines

Static. The problem here is badly chosen type of i. Like I mentioned at
the top of review…

I'll try to rewrite it with pass a structure. It seems more make sense.

That's correct on one side, on the other I'm not sure you got my comment. size_t is arch-dependent type, sizeof() is not the same everywhere.

Quoted 11 lines
drivers/mfd/f81504-core.c new file +1 -0
+	pci_read_config_byte(dev, F81504_GPIO_IO_MSB_REG, &tmp);
Quoted 5 lines

drivers/mfd/f81504-core.c line 253

Quoted 3 lines
drivers/mfd/f81504-core.c new file +3 -0
+	priv->gpio_ioaddr = tmp << 8;
+	pci_read_config_byte(dev, F81504_GPIO_IO_LSB_REG, &tmp);
+	priv->gpio_ioaddr |= tmp;

One read as word?

It can't read as word. The "F81504_GPIO_IO_LSB_REG" is 0xf1, It seems can't be read word/dword from a odd address.

I'll remain it.

Put comment about that.

Quoted 14 lines

Quoted 4 lines
Quoted 4 lines
drivers/mfd/f81504-core.c new file +3 -0
+static const struct pci_device_id f81504_dev_table[] = {
+	/* Fintek PCI serial cards */
+	{PCI_DEVICE(FINTEK_VID, FINTEK_F81504), .driver_data =

4},

Quoted 8 lines

drivers/mfd/f81504-core.c line 310

Quoted 5 lines
(quoted diff) +1 -0
+	{PCI_DEVICE(FINTEK_VID, FINTEK_F81508), .driver_data =

8},

(quoted diff) +1 -0
+	{PCI_DEVICE(FINTEK_VID, FINTEK_F81512), .driver_data =

12},

drivers/mfd/f81504-core.c new file +1 -0
+	{}

So, if you have default y for this and 8250_pci, which one will be loaded?

Quoted 3 lines

I had tested on x86, It'll handle by 8250_pci.c when this & 8250_pci.c
all built-in mode.

Yeah. here is the problem. When you introduce that you have to be sure that no-one will try to build kernel with both included right now.

To avoid potential problem you may split the driver to main part and Kconfig enabling part. Lee, what is your advice here?

Quoted 7 lines

BTW, due to the series patches across 3 subsystems MFD/GPIO/8250. I make the series patches under MFD subsystem, but the buildbot report git repository conflict with GPIO & 8250 (patch 2 & 3).

Should I split the series patches into 3 independent patch and based on their maintainer git repository?

It should go via one subsystem, otherwise user may end up with non- working interim kernel version, i.e. when bisecting.

In case if it based on some stuff which is not in upstream yet, you have to describe this carefully to maintainers that they may create immutable branches and cross-apply the stuff. But I suppose it's not your case and your series is quite straightforward.

Signature · 2 lines
Andy Shevchenko <[email protected]>
Intel Finland Oy
author
#10 lore raw

Re: [PATCH V2 1/4] mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

Hi Andy,

Andy Shevchenko 於 2016/1/29 下午 09:41 寫道:

Quoted 27 lines · Peter Hung
Quoted 15 lines

Andy Shevchenko 於 2016/1/28 下午 07:55 寫道:

Quoted 5 lines

I would suggest to rearrange definition block here (and in the rest of
the functions in entire series) to somehow follow the following pattern

Quoted 8 lines

1) assignments go first, especially container_of() based ones;
2) group variables by meaning and put longer lines upper;
3) return value variable, if exists, goes last.

Besides that choose types carefully. If there is known limit for counters, no need to define wider type than needed. Use proper types
for corresponding values.

Quoted 6 lines

I'll try to rearrange the definition blocks.

For the counter issue, some senior recommend me to change count from int
to size_t for performance.

Wow, how come? On which arch?

Also mark this as (1) to refer below.

Quoted 8 lines
Quoted 2 lines

In this case, should I use u8 to replace
i & j ? It should be less than 12 & 6.

At least you tell compiler that it may use any suitable type. In any case the last decision is by compiler if you don't do any tricks.

So, I suggest to use non-fixed width type like (unsigned) int and leave everything else on compiler.

Sorry for my misunderstanding, not for performance. The senior just recommend me to replace all size/count variables to size_t.

https://lkml.org/lkml/2016/1/3/193

size_t in x86 is unsigned int, x86_64 is unsigned long, It maybe good for prefetch or match register size I guess.

I'll make the size_t of series patches to unsigned int.

Quoted 9 lines
Quoted 9 lines
Quoted 8 lines

drivers/mfd/f81504-core.c line 34

Quoted 6 lines
(quoted diff) +1 -0
+	pci_write_config_byte(dev, F81504_GPIO_IO_LSB_REG,

gpio_addr
& 0xff);

(quoted diff) +1 -0
+	pci_write_config_byte(dev, F81504_GPIO_IO_MSB_REG,

(gpio_addr >> 8) &

drivers/mfd/f81504-core.c new file +1 -0
+			0xff);

Could it be written at once as a word?

Quoted 4 lines
Quoted 2 lines

I tested with writing a word to "F81504_GPIO_IO_LSB_REG", but it'll failed, so I'll remain it.

Please, add a comment line above.

ok

Quoted 22 lines
Quoted 11 lines
Quoted 11 lines

drivers/mfd/f81504-core.c line 54

Quoted 7 lines
(quoted diff) +2 -0
+	if (priv) {
+		/* Reinit from resume(), read the previous value

from priv */

drivers/mfd/f81504-core.c new file +1 -0
+		gpio_en = priv->gpio_en;

I would suggest to move this line down to follow same pattern in else
branch.

I'm talking here to make simple rearrangement like

if () {
…
gpio_en = …
} else {
…
gpio_en = …
}

Quoted 1 line

Thus the gpio_en assignment goes last in both branches.

ok

Quoted 13 lines
Quoted 13 lines
Quoted 12 lines
Quoted 10 lines
(quoted diff) +2 -0
+
+		pci_write_config_byte(dev, config_base + 0x06,

dev-

Quoted 1 line

irq);

drivers/mfd/f81504-core.c new file +3 -0
+
+		/*
+		 * Force init to RS232 / Share Mode, recovery

previous mode

(quoted diff) +1 -0
+		 * will done in F81504 8250 platform driver

resume()

Period at the end of sentences in multi-line comments.

Quoted 5 lines
Quoted 2 lines

Sorry, what this mean for ?
I cant use multi-line comments in the end ??

Sentences are started with capital letters and end with period '.' character, like this one.

ok.

Quoted 11 lines
Quoted 10 lines
(quoted diff) +1 -0
+		if (status) {
Quoted 6 lines

Review

Quoted 4 lines
(quoted diff) +1 -0
+			dev_warn(&dev->dev, "%s: add device

failed:
%d\n",

(quoted diff) +1 -0
+					__func__, status);

Indent _ under &.

Some senior recommend me to do at least 2-tabs to do indent when code cross multi-line. So I'll use to 2-tabs from "dev" to do indent.

Quoted 7 lines
Quoted 2 lines

How should I do with indent ?? It seems no consensus, but Lindent will do indent like your comments.

I would suggest to use what is used in most recent drivers and modules. I don't remember that 2 tabs fact is somehow reflected in CodingStyle.

Maybe your seniour was talkin about multi-line function definition?

ok, I'll indent multi-line statement as your comment and multi-line function with 2 tabs.

Quoted 6 lines
Quoted 6 lines
drivers/mfd/f81504-core.c new file +1 -0
+		f81504_gpio_cell.pdata_size = sizeof(i);
Quoted 4 lines

Static. The problem here is badly chosen type of i. Like I mentioned at
the top of review…

Quoted 6 lines
Quoted 2 lines

I'll try to rewrite it with pass a structure. It seems more make sense.

That's correct on one side, on the other I'm not sure you got my comment. size_t is arch-dependent type, sizeof() is not the same everywhere.

I'll change it to pass unsigned int.

Quoted 7 lines
Quoted 7 lines
drivers/mfd/f81504-core.c new file +1 -0
+	pci_read_config_byte(dev, F81504_GPIO_IO_MSB_REG, &tmp);
Quoted 5 lines

drivers/mfd/f81504-core.c line 253

Quoted 3 lines
drivers/mfd/f81504-core.c new file +3 -0
+	priv->gpio_ioaddr = tmp << 8;
+	pci_read_config_byte(dev, F81504_GPIO_IO_LSB_REG, &tmp);
+	priv->gpio_ioaddr |= tmp;

One read as word?

Quoted 6 lines
Quoted 4 lines

It can't read as word. The "F81504_GPIO_IO_LSB_REG" is 0xf1, It seems can't be read word/dword from a odd address.

I'll remain it.

Put comment about that.

ok

Quoted 9 lines
Quoted 6 lines
Quoted 2 lines

So, if you have default y for this and 8250_pci, which one will be loaded?

I had tested on x86, It'll handle by 8250_pci.c when this & 8250_pci.c
all built-in mode.

Yeah. here is the problem. When you introduce that you have to be sure that no-one will try to build kernel with both included right now.

Paul had recommend me to reduce the impact of code change. I'll remove all F81504/508/512 code in 8250_pci.c until the series patches had applied.

The device will handle with 8250_pci.c before applide patch no4, and handle with f81504_code.c when applied patch no4. This maybe reduce the bisect misleading.

Quoted 8 lines
Quoted 7 lines

BTW, due to the series patches across 3 subsystems MFD/GPIO/8250. I make the series patches under MFD subsystem, but the buildbot report git repository conflict with GPIO & 8250 (patch 2 & 3).

Should I split the series patches into 3 independent patch and based on their maintainer git repository?

Quoted 8 lines

It should go via one subsystem, otherwise user may end up with non- working interim kernel version, i.e. when bisecting.

In case if it based on some stuff which is not in upstream yet, you have to describe this carefully to maintainers that they may create immutable branches and cross-apply the stuff. But I suppose it's not your case and your series is quite straightforward.

I'll still try the series patch based on MFD subsystem. Thanks for your advices.

Signature · 6 lines
With Best Regards,
Peter Hung
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#26 lore raw

Re: [PATCH V2 4/4] serial: 8250_pci: Remove Fintek F81504/508/512 UART driver

In reply to Andy Shevchenko

Hi Andy,

Andy Shevchenko 於 2016/1/29 下午 08:40 寫道:

Quoted 17 lines · Peter Hung
Quoted 16 lines

Hi Andy,

Andy Shevchenko 於 2016/1/28 下午 08:04 寫道:

Quoted 12 lines · Peter Hung
Quoted 8 lines
(quoted diff) +0 -2
-	/* Fintek PCI serial cards */
-	{ PCI_DEVICE(0x1c29, 0x1104), .driver_data =

pbn_fintek_4 },

(quoted diff) +0 -1
-	{ PCI_DEVICE(0x1c29, 0x1108), .driver_data =

pbn_fintek_8 },

(quoted diff) +0 -1
-	{ PCI_DEVICE(0x1c29, 0x1112), .driver_data =

pbn_fintek_12
},

Shouldn't you blacklist them in 8250_pci?

Quoted 8 lines
Quoted 2 lines

You are referring to add blacklist instead of remove F81504/508/512 code?

No.

Quoted 1 line

or add blacklist and remove code?

This one.

ok

Quoted 4 lines

Check what lspci tells you about your device. I'm pretty sure that it has Serial Class, which would trigger enumeration in 8250_pci.c if it comes first.

I had add log with 8250_pci.c. It really trigger once by 8250_pci.c, but will failed with serial_pci_guess_board(). So It can be handled by f81504-core.c. I should add pid/vid to blacklist and comments it'll be handled by f81504-core.c

Thanks

Signature · 6 lines
With Best Regards,
Peter Hung
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#8 lore raw

Re: [PATCH V2 1/4] mfd: f81504-core: Add Fintek F81504/508/512 PCIE-to-UART/GPIO core support

In reply to Andy Shevchenko
Quoted 8 lines · Andy Shevchenko

Thin out Cc list since mostly off topic message here.

Quoted 1 line · Lee Jones

I prefer '-' in MFD.

Have to memorize that.

Quoted 7 lines

/* A bit of off topic */
I will cook and send one patch regarding to Intel Quark SoC, i.e. UART driver, but I'm not sure it's a good idea now to use there - since there are already too many intel_ files with _ including existing drivers for Quark.

What do you think?

Where is the UART driver? If it's in with the serial devices, you'd have to speak to the maintainer there. Probably best to just submit and let the maintainer let you know if something is incorrect.

Signature · 4 lines
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
#16 lore raw

Re: [PATCH V2 2/4] gpio: gpio-f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO GPIOLIB support

In reply to Peter Hung
Quoted 34 lines · Peter Hung

This driver is GPIOLIB driver for F81504/508/512, it'll handle the GPIOLIB operation of this device. This module will depend on MFD_FINTEK_F81504_CORE.

IC function list:
F81504: Max 2x8 GPIOs and max 4 serial ports
port2/3 are multi-function
F81508: Max 6x8 GPIOs and max 8 serial ports
port2/3 are multi-function, port8/9/10/11 are gpio only
F81512: Max 6x8 GPIOs and max 12 serial ports
port2/3/8/9/10/11 are multi-function

GPIO register:
PCI Configuration space:
F0h: bit0~5: Enable GPIO0~5
bit6~7: Reserve
F3h: bit0~5: Multi-Functional Flag (0:GPIO/1:UART)
bit0: UART2 pin out for UART2 / GPIO0
bit1: UART3 pin out for UART3 / GPIO1
bit2: UART8 pin out for UART8 / GPIO2
bit3: UART9 pin out for UART9 / GPIO3
bit4: UART10 pin out for UART10 / GPIO4
bit5: UART11 pin out for UART11 / GPIO5 bit6~7: Reserve
F1h: IO address (LSB)
F2h: IO address (MSB)
F8h + 8 * set: Direction control (bitwise)
bitx: 0 - Input mode
bitx: 1 - Output mode
F9h + 8 * set: Drive ability control (bitwise)
bitx: 0 - Open drain (default)
bitx: 1 - Push Pull
In this driver, we only implements open drain mode.

Quoted 6 lines

IO space:

    (IO base + 0~5): GPIO-0x~5x in/out value (bitwise)

Overall a very nice and interesting patch set.

Quoted 1 line

+++ b/drivers/gpio/gpio-f81504.c

(...)

drivers/gpio/gpio-f81504.c line 19

Quoted 2 lines
drivers/gpio/gpio-f81504.c new file +2 -0
+#include <linux/platform_device.h>
+#include <linux/gpio.h>

Drivers should just
#include <linux/gpio/driver.h>

drivers/gpio/gpio-f81504.c line 35

Quoted 4 lines
drivers/gpio/gpio-f81504.c new file +4 -0
+static struct f81504_gpio_chip *gpio_to_f81504_chip(struct gpio_chip *chip)
+{
+       return container_of(chip, struct f81504_gpio_chip, chip);
+}

Avoid this construction in new code.

Use gpiochip_get_data(chip) everywhere that gpio_to_f81504_chip() is used and register the gpiochip with gpiochip_add_data() and the code will be simpler.

See any other driver in drivers/gpio for examples, I converted them all.

Quoted 7 lines
drivers/gpio/gpio-f81504.c new file +7 -0
+static int f81504_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
+{
+       u8 tmp;
+       struct f81504_gpio_chip *gc = gpio_to_f81504_chip(chip);
+       struct platform_device *pdev = to_platform_device(chip->dev);
+       struct pci_dev *pci_dev = to_pci_dev(pdev->dev.parent);
+

drivers/gpio/gpio-f81504.c line 116

Quoted 10 lines
drivers/gpio/gpio-f81504.c new file +10 -0
+       mutex_lock(&gc->locker);
+       pci_read_config_byte(pci_dev, F81504_GPIO_START_ADDR + gc->idx *
+                       F81504_GPIO_SET_OFFSET, &tmp);
+       mutex_unlock(&gc->locker);
+
+       if (tmp & BIT(offset))
+               return GPIOF_DIR_OUT;
+
+       return GPIOF_DIR_IN;
+}

Do not use GPIOF* flags in driver code, these are for the consumer API. Just return 0/1.

Quoted 1 line

+ status = gpiochip_add(&gc->chip);

As mentioned, use gpiochip_add_data(&gc->chip, gc);

drivers/gpio/gpio-f81504.c line 246

Quoted 4 lines
drivers/gpio/gpio-f81504.c new file +4 -0
+static struct platform_driver f81504_gpio_driver = {
+       .driver = {
+               .name   = F81504_GPIO_NAME,
+               .owner  = THIS_MODULE,

I saw coccinelle was already complaining about this.

Looking forward to v3!

Yours,
Linus Walleij

author
#17 lore raw

Re: [PATCH V2 2/4] gpio: gpio-f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO GPIOLIB support

Hi Linus,

Linus Walleij 於 2016/2/10 下午 05:08 寫道:

Quoted 6 lines · Peter Hung

drivers/gpio/gpio-f81504.c line 19

Quoted 2 lines
drivers/gpio/gpio-f81504.c new file +2 -0
+#include <linux/platform_device.h>
+#include <linux/gpio.h>

Drivers should just
#include <linux/gpio/driver.h>

ok.

Quoted 7 lines

drivers/gpio/gpio-f81504.c line 35

Quoted 4 lines
drivers/gpio/gpio-f81504.c new file +4 -0
+static struct f81504_gpio_chip *gpio_to_f81504_chip(struct gpio_chip *chip)
+{
+       return container_of(chip, struct f81504_gpio_chip, chip);
+}

Avoid this construction in new code.

Quoted 6 lines

Use gpiochip_get_data(chip) everywhere that gpio_to_f81504_chip() is used and register the gpiochip with gpiochip_add_data() and the code will be simpler.

See any other driver in drivers/gpio for examples, I converted them all.

ok. I'll re-write this section.

Quoted 9 lines

drivers/gpio/gpio-f81504.c line 116

Quoted 6 lines
drivers/gpio/gpio-f81504.c new file +6 -0
+
+       if (tmp & BIT(offset))
+               return GPIOF_DIR_OUT;
+
+       return GPIOF_DIR_IN;
+}

Do not use GPIOF* flags in driver code, these are for the consumer API. Just return 0/1.

ok

Quoted 4 lines
Quoted 1 line

+ status = gpiochip_add(&gc->chip);

As mentioned, use gpiochip_add_data(&gc->chip, gc);

ok.

Quoted 8 lines

drivers/gpio/gpio-f81504.c line 246

Quoted 4 lines
drivers/gpio/gpio-f81504.c new file +4 -0
+static struct platform_driver f81504_gpio_driver = {
+       .driver = {
+               .name   = F81504_GPIO_NAME,
+               .owner  = THIS_MODULE,

I saw coccinelle was already complaining about this.

Looking forward to v3!

I had sent V3 today to resolve the issue above.

Thanks for your advices.

Signature · 6 lines
With Best Regards,
Peter Hung
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html