spi: omap3: Convert to driver model
PATCH v3 1/1 spi: omap3: Convert to driver model
After this conversion the driver will able to support both dm and non-dm and code is more extensible like we can remove the non-dm part simply without touching anycode if all the boards which are using this driver become dm driven.
Cc Tom Rini <[email protected]>
Reviewed-by Simon Glass <[email protected]>
Signed-off-by Jagan Teki <[email protected]>
---
Changes for v3:
- Add DECLARE_GLOBAL_DATA_PTR
Changes for v2:
- Added dm pindir-d0-out-d1-in logic
- Updated comment about 4-wire master mode as per Linux.
drivers/spi/omap3_spi.c | 686 +++++++++++++++++++++++++++++------------------- 1 file changed, 415 insertions(+), 271 deletions(-)
drivers/spi/omap3_spi.c +415 -271
@@ -1,4 +1,6 @@/* +* Copyright (C) 2016 Jagan Teki <[email protected]> +* * Copyright (C) 2010 Dirk Behme <[email protected]> * * Driver for McSPI controller on OMAP3. Based on davinci_spi.c
@@ -15,10 +17,13 @@*/ #include <common.h> +#include <dm.h> #include <spi.h> #include <malloc.h> #include <asm/io.h> +DECLARE_GLOBAL_DATA_PTR ; +#if defined(CONFIG_AM33XX ) || defined(CONFIG_AM43XX )#define OMAP3_MCSPI1_BASE 0x48030100#define OMAP3_MCSPI2_BASE 0x481A0100
@@ -65,6 +70,8 @@#define OMAP3_MCSPI_CHCTRL_DIS (0 << 0)#define OMAP3_MCSPI_WAKEUPENABLE_WKEN BIT(0) +#define MCSPI_PINDIR_D0_IN_D1_OUT 0 +#define MCSPI_PINDIR_D0_OUT_D1_IN 1#define OMAP3_MCSPI_MAX_FREQ 48000000#define SPI_WAIT_TIMEOUT 10
@@ -93,312 +100,123 @@ struct mcspi {/* channel3: 0x68 - 0x78, bus 0 */ }; -struct omap3_spi_slave { -struct spi_slave slave; +struct omap3_spi_priv {struct mcspi *regs; +unsigned int cs;unsigned int freq;unsigned int mode; +unsigned int wordlen; +unsigned int pin_dir:1 ; }; -static inline struct omap3_spi_slave *to_omap3_spi (struct spi_slave *slave) -{ - return container_of(slave, struct omap3_spi_slave, slave); -} - -static void spi_reset (struct omap3_spi_slave *ds) -{ -unsigned int tmp; - -writel (OMAP3_MCSPI_SYSCONFIG_SOFTRESET , &ds->regs->sysconfig); -do { - tmp =readl (&ds->regs->sysstatus); - }while (!(tmp &OMAP3_MCSPI_SYSSTATUS_RESETDONE )); - -writel (OMAP3_MCSPI_SYSCONFIG_AUTOIDLE | -OMAP3_MCSPI_SYSCONFIG_ENAWAKEUP | -OMAP3_MCSPI_SYSCONFIG_SMARTIDLE , - &ds->regs->sysconfig); - -writel (OMAP3_MCSPI_WAKEUPENABLE_WKEN , &ds->regs->wakeupenable); -} - -static void omap3_spi_write_chconf (struct omap3_spi_slave *ds,int val) +static void omap3_spi_write_chconf (struct omap3_spi_priv *priv,int val) { -writel (val, &ds->regs->channel[ds->slave.cs].chconf); +writel (val, &priv->regs->channel[priv->cs].chconf);/* Flash post writes to make immediate effect */ -readl (&ds->regs->channel[ds->slave.cs].chconf); +readl (&priv->regs->channel[priv->cs].chconf); } -static void omap3_spi_set_enable (struct omap3_spi_slave *ds,int enable) +static void omap3_spi_set_enable (struct omap3_spi_priv *priv,int enable) { -writel (enable, &ds->regs->channel[ds->slave.cs].chctrl); +writel (enable, &priv->regs->channel[priv->cs].chctrl);/* Flash post writes to make immediate effect */ -readl (&ds->regs->channel[ds->slave.cs].chctrl); -} - -void spi_init () -{ -/* do nothing */ +readl (&priv->regs->channel[priv->cs].chctrl); } -struct spi_slave *spi_setup_slave (unsigned int bus,unsigned int cs, -unsigned int max_hz,unsigned int mode) -{ -struct omap3_spi_slave *ds; -struct mcspi *regs; - -/* -* OMAP3 McSPI (MultiChannel SPI) has 4 busses (modules) -* with different number of chip selects (CS, channels): -* McSPI1 has 4 CS (bus 0, cs 0 - 3) -* McSPI2 has 2 CS (bus 1, cs 0 - 1) -* McSPI3 has 2 CS (bus 2, cs 0 - 1) -* McSPI4 has 1 CS (bus 3, cs 0) -*/ - -switch (bus) { -case 0 : - regs = (struct mcspi *)OMAP3_MCSPI1_BASE ; -break ; -#ifdef OMAP3_MCSPI2_BASE -case 1 : - regs = (struct mcspi *)OMAP3_MCSPI2_BASE ; -break ; -#endif -#ifdef OMAP3_MCSPI3_BASE -case 2 : - regs = (struct mcspi *)OMAP3_MCSPI3_BASE ; -break ; -#endif -#ifdef OMAP3_MCSPI4_BASE -case 3 : - regs = (struct mcspi *)OMAP3_MCSPI4_BASE ; -break ; -#endif -default : -printf ("SPI error: unsupported bus %i. \ -Supported busses 0 - 3\n" , bus); -return NULL ; - } - -if (((bus ==0 ) && (cs >3 )) || - ((bus ==1 ) && (cs >1 )) || - ((bus ==2 ) && (cs >1 )) || - ((bus ==3 ) && (cs >0 ))) { -printf ("SPI error: unsupported chip select %i \ -on bus %i\n" , cs, bus); -return NULL ; - } - -if (max_hz >OMAP3_MCSPI_MAX_FREQ ) { -printf ("SPI error: unsupported frequency %i Hz. \ -Max frequency is 48 Mhz\n" , max_hz); -return NULL ; - } - -if (mode >SPI_MODE_3 ) { -printf ("SPI error: unsupported SPI mode %i\n" , mode); -return NULL ; - } - - ds = spi_alloc_slave(struct omap3_spi_slave, bus, cs); -if (!ds) { -printf ("SPI error: malloc of SPI structure failed\n" ); -return NULL ; - } - - ds->regs = regs; - ds->freq = max_hz; - ds->mode = mode; - -return &ds->slave; -} - -void spi_free_slave (struct spi_slave *slave) -{ -struct omap3_spi_slave *ds =to_omap3_spi (slave); - -free (ds); -} - -int spi_claim_bus (struct spi_slave *slave) -{ -struct omap3_spi_slave *ds =to_omap3_spi (slave); -unsigned int conf, div =0 ; - -/* McSPI global module configuration */ - -/* -* setup when switching from (reset default) slave mode -* to single-channel master mode -*/ -spi_reset (ds); - conf =readl (&ds->regs->modulctrl); - conf &= ~(OMAP3_MCSPI_MODULCTRL_STEST |OMAP3_MCSPI_MODULCTRL_MS ); - conf |=OMAP3_MCSPI_MODULCTRL_SINGLE ; -writel (conf, &ds->regs->modulctrl); - -/* McSPI individual channel configuration */ - -/* Calculate clock divisor. Valid range: 0x0 - 0xC ( /1 - /4096 ) */ -if (ds->freq) { -while (div <=0xC && (OMAP3_MCSPI_MAX_FREQ / (1 << div)) - > ds->freq) - div++; - }else - div =0xC ; - - conf =readl (&ds->regs->channel[ds->slave.cs].chconf); - -/* standard 4-wire master mode: SCK, MOSI/out, MISO/in, nCS -* REVISIT: this controller could support SPI_3WIRE mode. -*/ -#ifdef CONFIG_OMAP3_SPI_D0_D1_SWAPPED -/* -* Some boards have D0 wired as MOSI / D1 as MISO instead of -* The normal D0 as MISO / D1 as MOSI. -*/ - conf &= ~OMAP3_MCSPI_CHCONF_DPE0 ; - conf |=OMAP3_MCSPI_CHCONF_IS |OMAP3_MCSPI_CHCONF_DPE1 ; -#else - conf &= ~(OMAP3_MCSPI_CHCONF_IS |OMAP3_MCSPI_CHCONF_DPE1 ); - conf |=OMAP3_MCSPI_CHCONF_DPE0 ; -#endif - -/* wordlength */ - conf &= ~OMAP3_MCSPI_CHCONF_WL_MASK ; - conf |= (ds->slave.wordlen -1 ) <<7 ; - -/* set chipselect polarity; manage with FORCE */ -if (!(ds->mode &SPI_CS_HIGH )) - conf |=OMAP3_MCSPI_CHCONF_EPOL ;/* active-low; normal */ -else - conf &= ~OMAP3_MCSPI_CHCONF_EPOL ; - -/* set clock divisor */ - conf &= ~OMAP3_MCSPI_CHCONF_CLKD_MASK ; - conf |= div <<2 ; - -/* set SPI mode 0..3 */ -if (ds->mode &SPI_CPOL ) - conf |=OMAP3_MCSPI_CHCONF_POL ; -else - conf &= ~OMAP3_MCSPI_CHCONF_POL ; -if (ds->mode &SPI_CPHA ) - conf |=OMAP3_MCSPI_CHCONF_PHA ; -else - conf &= ~OMAP3_MCSPI_CHCONF_PHA ; - -/* Transmit & receive mode */ - conf &= ~OMAP3_MCSPI_CHCONF_TRM_MASK ; - -omap3_spi_write_chconf (ds,conf); - -return 0 ; -} - -void spi_release_bus (struct spi_slave *slave) -{ -struct omap3_spi_slave *ds =to_omap3_spi (slave); - -/* Reset the SPI hardware */ -spi_reset (ds); -} - -static int omap3_spi_write (struct spi_slave *slave,unsigned int len, +static int omap3_spi_write (struct omap3_spi_priv *priv,unsigned int len,const void *txp,unsigned long flags) { -struct omap3_spi_slave *ds =to_omap3_spi (slave); -int i;ulong start; -int chconf =readl (&ds->regs->channel[ds->slave.cs].chconf); +int chconf, i; + + chconf =readl (&priv->regs->channel[priv->cs].chconf);/* Enable the channel */ -omap3_spi_set_enable (ds,OMAP3_MCSPI_CHCTRL_EN ); +omap3_spi_set_enable (priv,OMAP3_MCSPI_CHCTRL_EN ); chconf &= ~(OMAP3_MCSPI_CHCONF_TRM_MASK |OMAP3_MCSPI_CHCONF_WL_MASK ); - chconf |= (ds->slave.wordlen -1 ) <<7 ; + chconf |= (priv->wordlen -1 ) <<7 ; chconf |=OMAP3_MCSPI_CHCONF_TRM_TX_ONLY ; chconf |=OMAP3_MCSPI_CHCONF_FORCE ; -omap3_spi_write_chconf (ds,chconf); +omap3_spi_write_chconf (priv, chconf);for (i =0 ; i < len; i++) {/* wait till TX register is empty (TXS == 1) */ start =get_timer (0 ); -while (!(readl (&ds->regs->channel[ds->slave.cs].chstat) & +while (!(readl (&priv->regs->channel[priv->cs].chstat) &OMAP3_MCSPI_CHSTAT_TXS )) {if (get_timer (start) >SPI_WAIT_TIMEOUT ) {printf ("SPI TXS timed out, status=0x%08x\n" , -readl (&ds->regs->channel[ds->slave.cs].chstat)); +readl (&priv->regs->channel[priv->cs].chstat));return -1 ; } }/* Write the data */ -unsigned int *tx = &ds->regs->channel[ds->slave.cs].tx; -if (ds->slave.wordlen >16 ) +unsigned int *tx = &priv->regs->channel[priv->cs].tx; +if (priv->wordlen >16 )writel (((u32 *)txp)[i], tx); -else if (ds->slave.wordlen >8 ) +else if (priv->wordlen >8 )writel (((u16 *)txp)[i], tx);else writel (((u8 *)txp)[i], tx); }/* wait to finish of transfer */ -while ((readl (&ds->regs->channel[ds->slave.cs].chstat) & +while ((readl (&priv->regs->channel[priv->cs].chstat) & (OMAP3_MCSPI_CHSTAT_EOT |OMAP3_MCSPI_CHSTAT_TXS )) != (OMAP3_MCSPI_CHSTAT_EOT |OMAP3_MCSPI_CHSTAT_TXS ));/* Disable the channel otherwise the next immediate RX will get affected */ -omap3_spi_set_enable (ds,OMAP3_MCSPI_CHCTRL_DIS ); +omap3_spi_set_enable (priv,OMAP3_MCSPI_CHCTRL_DIS );if (flags &SPI_XFER_END ) { - chconf &= ~OMAP3_MCSPI_CHCONF_FORCE ; -omap3_spi_write_chconf (ds,chconf); +omap3_spi_write_chconf (priv, chconf); } +return 0 ; } -static int omap3_spi_read (struct spi_slave *slave,unsigned int len, +static int omap3_spi_read (struct omap3_spi_priv *priv,unsigned int len,void *rxp,unsigned long flags) { -struct omap3_spi_slave *ds =to_omap3_spi (slave); -int i;ulong start; -int chconf =readl (&ds->regs->channel[ds->slave.cs].chconf); +int chconf, i; + + chconf =readl (&priv->regs->channel[priv->cs].chconf);/* Enable the channel */ -omap3_spi_set_enable (ds,OMAP3_MCSPI_CHCTRL_EN ); +omap3_spi_set_enable (priv,OMAP3_MCSPI_CHCTRL_EN ); chconf &= ~(OMAP3_MCSPI_CHCONF_TRM_MASK |OMAP3_MCSPI_CHCONF_WL_MASK ); - chconf |= (ds->slave.wordlen -1 ) <<7 ; + chconf |= (priv->wordlen -1 ) <<7 ; chconf |=OMAP3_MCSPI_CHCONF_TRM_RX_ONLY ; chconf |=OMAP3_MCSPI_CHCONF_FORCE ; -omap3_spi_write_chconf (ds,chconf); +omap3_spi_write_chconf (priv, chconf); -writel (0 , &ds->regs->channel[ds->slave.cs].tx); +writel (0 , &priv->regs->channel[priv->cs].tx);for (i =0 ; i < len; i++) { start =get_timer (0 );/* Wait till RX register contains data (RXS == 1) */ -while (!(readl (&ds->regs->channel[ds->slave.cs].chstat) & +while (!(readl (&priv->regs->channel[priv->cs].chstat) &OMAP3_MCSPI_CHSTAT_RXS )) {if (get_timer (start) >SPI_WAIT_TIMEOUT ) {printf ("SPI RXS timed out, status=0x%08x\n" , -readl (&ds->regs->channel[ds->slave.cs].chstat)); +readl (&priv->regs->channel[priv->cs].chstat));return -1 ; } }/* Disable the channel to prevent furher receiving */ -if (i == (len -1 )) -omap3_spi_set_enable (ds,OMAP3_MCSPI_CHCTRL_DIS ); +if (i == (len -1 )) +omap3_spi_set_enable (priv,OMAP3_MCSPI_CHCTRL_DIS );/* Read the data */ -unsigned int *rx = &ds->regs->channel[ds->slave.cs].rx; -if (ds->slave.wordlen >16 ) +unsigned int *rx = &priv->regs->channel[priv->cs].rx; +if (priv->wordlen >16 ) ((u32 *)rxp)[i] =readl (rx); -else if (ds->slave.wordlen >8 ) +else if (priv->wordlen >8 ) ((u16 *)rxp)[i] = (u16 )readl (rx);else ((u8 *)rxp)[i] = (u8 )readl (rx);
@@ -406,133 +224,459 @@ static int omap3_spi_read(struct spi_slave *slave, unsigned int len,if (flags &SPI_XFER_END ) { chconf &= ~OMAP3_MCSPI_CHCONF_FORCE ; -omap3_spi_write_chconf (ds,chconf); +omap3_spi_write_chconf (priv, chconf); }return 0 ; }/*McSPI Transmit Receive Mode*/ -static int omap3_spi_txrx (struct spi_slave *slave,unsigned int len, +static int omap3_spi_txrx (struct omap3_spi_priv *priv,unsigned int len,const void *txp,void *rxp,unsigned long flags) { -struct omap3_spi_slave *ds =to_omap3_spi (slave);ulong start; -int chconf =readl (&ds->regs->channel[ds->slave.cs].chconf); -int i=0 ; +int chconf, i =0 ; + + chconf =readl (&priv->regs->channel[priv->cs].chconf);/*Enable SPI channel*/ -omap3_spi_set_enable (ds,OMAP3_MCSPI_CHCTRL_EN ); +omap3_spi_set_enable (priv,OMAP3_MCSPI_CHCTRL_EN );/*set TRANSMIT-RECEIVE Mode*/ chconf &= ~(OMAP3_MCSPI_CHCONF_TRM_MASK |OMAP3_MCSPI_CHCONF_WL_MASK ); - chconf |= (ds->slave.wordlen -1 ) <<7 ; + chconf |= (priv->wordlen -1 ) <<7 ; chconf |=OMAP3_MCSPI_CHCONF_FORCE ; -omap3_spi_write_chconf (ds,chconf); +omap3_spi_write_chconf (priv, chconf);/*Shift in and out 1 byte@time*/ -for (i=0 ; i < len; i++){ +for (i =0 ; i < len; i++) {/* Write: wait for TX empty (TXS == 1)*/ start =get_timer (0 ); -while (!(readl (&ds->regs->channel[ds->slave.cs].chstat) & +while (!(readl (&priv->regs->channel[priv->cs].chstat) &OMAP3_MCSPI_CHSTAT_TXS )) {if (get_timer (start) >SPI_WAIT_TIMEOUT ) {printf ("SPI TXS timed out, status=0x%08x\n" , -readl (&ds->regs->channel[ds->slave.cs].chstat)); +readl (&priv->regs->channel[priv->cs].chstat));return -1 ; } }/* Write the data */ -unsigned int *tx = &ds->regs->channel[ds->slave.cs].tx; -if (ds->slave.wordlen >16 ) +unsigned int *tx = &priv->regs->channel[priv->cs].tx; +if (priv->wordlen >16 )writel (((u32 *)txp)[i], tx); -else if (ds->slave.wordlen >8 ) +else if (priv->wordlen >8 )writel (((u16 *)txp)[i], tx);else writel (((u8 *)txp)[i], tx);/*Read: wait for RX containing data (RXS == 1)*/ start =get_timer (0 ); -while (!(readl (&ds->regs->channel[ds->slave.cs].chstat) & +while (!(readl (&priv->regs->channel[priv->cs].chstat) &OMAP3_MCSPI_CHSTAT_RXS )) {if (get_timer (start) >SPI_WAIT_TIMEOUT ) {printf ("SPI RXS timed out, status=0x%08x\n" , -readl (&ds->regs->channel[ds->slave.cs].chstat)); +readl (&priv->regs->channel[priv->cs].chstat));return -1 ; } }/* Read the data */ -unsigned int *rx = &ds->regs->channel[ds->slave.cs].rx; -if (ds->slave.wordlen >16 ) +unsigned int *rx = &priv->regs->channel[priv->cs].rx; +if (priv->wordlen >16 ) ((u32 *)rxp)[i] =readl (rx); -else if (ds->slave.wordlen >8 ) +else if (priv->wordlen >8 ) ((u16 *)rxp)[i] = (u16 )readl (rx);else ((u8 *)rxp)[i] = (u8 )readl (rx); }/* Disable the channel */ -omap3_spi_set_enable (ds,OMAP3_MCSPI_CHCTRL_DIS ); +omap3_spi_set_enable (priv,OMAP3_MCSPI_CHCTRL_DIS );/*if transfer must be terminated disable the channel*/ if (flags &SPI_XFER_END ) { chconf &= ~OMAP3_MCSPI_CHCONF_FORCE ; -omap3_spi_write_chconf (ds,chconf); +omap3_spi_write_chconf (priv, chconf); }return 0 ; } -int spi_xfer (struct spi_slave *slave,unsigned int bitlen, -const void *dout,void *din,unsigned long flags) +static int _spi_xfer (struct omap3_spi_priv *priv,unsigned int bitlen, +const void *dout,void *din,unsigned long flags) { -struct omap3_spi_slave *ds =to_omap3_spi (slave); -unsigned int len; +unsigned int len;int ret =-1 ; -if (ds->slave.wordlen <4 || ds->slave.wordlen >32 ) { -printf ("omap3_spi: invalid wordlen %d\n" , ds->slave.wordlen); +if (priv->wordlen <4 || priv->wordlen >32 ) { +printf ("omap3_spi: invalid wordlen %d\n" , priv->wordlen);return -1 ; } -if (bitlen % ds->slave.wordlen) +if (bitlen % priv->wordlen)return -1 ; - len = bitlen / ds->slave.wordlen; + len = bitlen / priv->wordlen;if (bitlen ==0 ) {/* only change CS */ -int chconf =readl (&ds->regs->channel[ds->slave.cs].chconf); +int chconf =readl (&priv->regs->channel[priv->cs].chconf);if (flags &SPI_XFER_BEGIN ) { -omap3_spi_set_enable (ds,OMAP3_MCSPI_CHCTRL_EN ); +omap3_spi_set_enable (priv,OMAP3_MCSPI_CHCTRL_EN ); chconf |=OMAP3_MCSPI_CHCONF_FORCE ; -omap3_spi_write_chconf (ds,chconf); +omap3_spi_write_chconf (priv, chconf); }if (flags &SPI_XFER_END ) { chconf &= ~OMAP3_MCSPI_CHCONF_FORCE ; -omap3_spi_write_chconf (ds,chconf); -omap3_spi_set_enable (ds,OMAP3_MCSPI_CHCTRL_DIS ); +omap3_spi_write_chconf (priv, chconf); +omap3_spi_set_enable (priv,OMAP3_MCSPI_CHCTRL_DIS ); } ret =0 ; }else {if (dout !=NULL && din !=NULL ) - ret =omap3_spi_txrx (slave, len, dout, din, flags); + ret =omap3_spi_txrx (priv, len, dout, din, flags);else if (dout !=NULL ) - ret =omap3_spi_write (slave, len, dout, flags); + ret =omap3_spi_write (priv, len, dout, flags);else if (din !=NULL ) - ret =omap3_spi_read (slave, len, din, flags); + ret =omap3_spi_read (priv, len, din, flags); }return ret; } -int spi_cs_is_valid (unsigned int bus,unsigned int cs) +static void _omap3_spi_set_speed (struct omap3_spi_priv *priv) +{ +uint32_t confr, div =0 ; + + confr =readl (&priv->regs->channel[priv->cs].chconf); + +/* Calculate clock divisor. Valid range: 0x0 - 0xC ( /1 - /4096 ) */ +if (priv->freq) { +while (div <=0xC && (OMAP3_MCSPI_MAX_FREQ / (1 << div)) + > priv->freq) + div++; + }else { + div =0xC ; + } + +/* set clock divisor */ + confr &= ~OMAP3_MCSPI_CHCONF_CLKD_MASK ; + confr |= div <<2 ; + +omap3_spi_write_chconf (priv, confr); +} + +static void _omap3_spi_set_mode (struct omap3_spi_priv *priv) +{ +uint32_t confr; + + confr =readl (&priv->regs->channel[priv->cs].chconf); + +/* standard 4-wire master mode: SCK, MOSI/out, MISO/in, nCS +* REVISIT: this controller could support SPI_3WIRE mode. +*/ +if (priv->pin_dir ==MCSPI_PINDIR_D0_IN_D1_OUT ) { + confr &= ~(OMAP3_MCSPI_CHCONF_IS |OMAP3_MCSPI_CHCONF_DPE1 ); + confr |=OMAP3_MCSPI_CHCONF_DPE0 ; + }else { + confr &= ~OMAP3_MCSPI_CHCONF_DPE0 ; + confr |=OMAP3_MCSPI_CHCONF_IS |OMAP3_MCSPI_CHCONF_DPE1 ; + } + +/* set SPI mode 0..3 */ + confr &= ~(OMAP3_MCSPI_CHCONF_POL |OMAP3_MCSPI_CHCONF_PHA ); +if (priv->mode &SPI_CPHA ) + confr |=OMAP3_MCSPI_CHCONF_PHA ; +if (priv->mode &SPI_CPOL ) + confr |=OMAP3_MCSPI_CHCONF_POL ; + +/* set chipselect polarity; manage with FORCE */ +if (!(priv->mode &SPI_CS_HIGH )) + confr |=OMAP3_MCSPI_CHCONF_EPOL ;/* active-low; normal */ +else + confr &= ~OMAP3_MCSPI_CHCONF_EPOL ; + +/* Transmit & receive mode */ + confr &= ~OMAP3_MCSPI_CHCONF_TRM_MASK ; + +omap3_spi_write_chconf (priv, confr); +} + +static void _omap3_spi_set_wordlen (struct omap3_spi_priv *priv) { -return 1 ; +unsigned int confr; + +/* McSPI individual channel configuration */ + confr =readl (&priv->regs->channel[priv->wordlen].chconf); + +/* wordlength */ + confr &= ~OMAP3_MCSPI_CHCONF_WL_MASK ; + confr |= (priv->wordlen -1 ) <<7 ; + +omap3_spi_write_chconf (priv, confr); } -void spi_cs_activate (struct spi_slave *slave) +static void spi_reset (struct mcspi *regs) { +unsigned int tmp; + +writel (OMAP3_MCSPI_SYSCONFIG_SOFTRESET , ®s->sysconfig); +do { + tmp =readl (®s->sysstatus); + }while (!(tmp &OMAP3_MCSPI_SYSSTATUS_RESETDONE )); + +writel (OMAP3_MCSPI_SYSCONFIG_AUTOIDLE | +OMAP3_MCSPI_SYSCONFIG_ENAWAKEUP | +OMAP3_MCSPI_SYSCONFIG_SMARTIDLE , + ®s->sysconfig); + +writel (OMAP3_MCSPI_WAKEUPENABLE_WKEN , ®s->wakeupenable); } -void spi_cs_deactivate (struct spi_slave *slave) +static void _omap3_spi_claim_bus (struct omap3_spi_priv *priv) { +unsigned int conf; + +spi_reset (priv->regs); + +/* +* setup when switching from (reset default) slave mode +* to single-channel master mode +*/ + conf =readl (&priv->regs->modulctrl); + conf &= ~(OMAP3_MCSPI_MODULCTRL_STEST |OMAP3_MCSPI_MODULCTRL_MS ); + conf |=OMAP3_MCSPI_MODULCTRL_SINGLE ; + +writel (conf, &priv->regs->modulctrl); + +_omap3_spi_set_mode (priv); +_omap3_spi_set_speed (priv); } + +#ifndef CONFIG_DM_SPI + +struct omap3_spi_slave { +struct spi_slave slave; +struct omap3_spi_priv spi_priv; +}; + +struct omap3_spi_priv *priv; + +static inline struct omap3_spi_slave *to_omap3_spi (struct spi_slave *slave) +{ + return container_of(slave, struct omap3_spi_slave, slave); +} + +void spi_init (void ) +{ +/* do nothing */ +} + +void spi_free_slave (struct spi_slave *slave) +{ +struct omap3_spi_slave *ds =to_omap3_spi (slave); + +free (ds); +} + +int spi_claim_bus (struct spi_slave *slave) +{ +_omap3_spi_claim_bus (priv); +_omap3_spi_set_wordlen (priv); +_omap3_spi_set_mode (priv); +_omap3_spi_set_speed (priv); + +return 0 ; +} + +void spi_release_bus (struct spi_slave *slave) +{ +/* Reset the SPI hardware */ +spi_reset (priv->regs); +} + +struct spi_slave *spi_setup_slave (unsigned int bus,unsigned int cs, +unsigned int max_hz,unsigned int mode) +{ +struct omap3_spi_slave *ds; +struct mcspi *regs; + +/* +* OMAP3 McSPI (MultiChannel SPI) has 4 busses (modules) +* with different number of chip selects (CS, channels): +* McSPI1 has 4 CS (bus 0, cs 0 - 3) +* McSPI2 has 2 CS (bus 1, cs 0 - 1) +* McSPI3 has 2 CS (bus 2, cs 0 - 1) +* McSPI4 has 1 CS (bus 3, cs 0) +*/ + +switch (bus) { +case 0 : + regs = (struct mcspi *)OMAP3_MCSPI1_BASE ; +break ; +#ifdef OMAP3_MCSPI2_BASE +case 1 : + regs = (struct mcspi *)OMAP3_MCSPI2_BASE ; +break ; +#endif +#ifdef OMAP3_MCSPI3_BASE +case 2 : + regs = (struct mcspi *)OMAP3_MCSPI3_BASE ; +break ; +#endif +#ifdef OMAP3_MCSPI4_BASE +case 3 : + regs = (struct mcspi *)OMAP3_MCSPI4_BASE ; +break ; +#endif +default : +printf ("SPI error: unsupported bus %i. \ +Supported busses 0 - 3\n" , bus); +return NULL ; + } + +if (((bus ==0 ) && (cs >3 )) || + ((bus ==1 ) && (cs >1 )) || + ((bus ==2 ) && (cs >1 )) || + ((bus ==3 ) && (cs >0 ))) { +printf ("SPI error: unsupported chip select %i \ +on bus %i\n" , cs, bus); +return NULL ; + } + +if (max_hz >OMAP3_MCSPI_MAX_FREQ ) { +printf ("SPI error: unsupported frequency %i Hz. \ +Max frequency is 48 Mhz\n" , max_hz); +return NULL ; + } + +if (mode >SPI_MODE_3 ) { +printf ("SPI error: unsupported SPI mode %i\n" , mode); +return NULL ; + } + + ds = spi_alloc_slave(struct omap3_spi_slave, bus, cs); +if (!ds) { +printf ("SPI error: malloc of SPI structure failed\n" ); +return NULL ; + } + + priv = &ds->spi_priv; + + priv->regs = regs; + priv->cs = cs; + priv->freq = max_hz; + priv->mode = mode; + priv->wordlen = ds->slave.wordlen; +#ifdef CONFIG_OMAP3_SPI_D0_D1_SWAPPED + priv->pin_dir =MCSPI_PINDIR_D0_OUT_D1_IN ; +#endif + +return &ds->slave; +} + +int spi_xfer (struct spi_slave *slave,unsigned int bitlen, +const void *dout,void *din,unsigned long flags) +{ +return _spi_xfer (priv, bitlen, dout, din, flags); +} + +#else + +static int omap3_spi_claim_bus (struct udevice *dev) +{ +struct udevice *bus = dev->parent; +struct omap3_spi_priv *priv =dev_get_priv (bus); +struct dm_spi_slave_platdata *slave_plat =dev_get_parent_platdata (dev); + + priv->cs = slave_plat->cs; + priv->mode = slave_plat->mode; + priv->freq = slave_plat->max_hz; +_omap3_spi_claim_bus (priv); + +return 0 ; +} + +static int omap3_spi_release_bus (struct udevice *dev) +{ +struct udevice *bus = dev->parent; +struct omap3_spi_priv *priv =dev_get_priv (bus); + +/* Reset the SPI hardware */ +spi_reset (priv->regs); + +return 0 ; +} + +static int omap3_spi_set_wordlen (struct udevice *dev,unsigned int wordlen) +{ +struct udevice *bus = dev->parent; +struct omap3_spi_priv *priv =dev_get_priv (bus); +struct dm_spi_slave_platdata *slave_plat =dev_get_parent_platdata (dev); + + priv->cs = slave_plat->cs; + priv->wordlen = wordlen; +_omap3_spi_set_wordlen (priv); + +return 0 ; +} + +static int omap3_spi_probe (struct udevice *dev) +{ +struct udevice *bus = dev->parent; +struct omap3_spi_priv *priv =dev_get_priv (bus); +const void *blob = gd->fdt_blob; +int node = bus->of_offset; + + priv->regs = (struct mcspi *)dev_get_addr (bus); + priv->pin_dir =fdtdec_get_uint (blob, node,"ti,pindir-d0-out-d1-in" , +MCSPI_PINDIR_D0_IN_D1_OUT ); + +return 0 ; +} + +static int omap3_spi_xfer (struct udevice *dev,unsigned int bitlen, +const void *dout,void *din,unsigned long flags) +{ +struct udevice *bus = dev->parent; +struct omap3_spi_priv *priv =dev_get_priv (bus); + +return _spi_xfer (priv, bitlen, dout, din, flags); +} + +static int omap3_spi_set_speed (struct udevice *bus,unsigned int speed) +{ +return 0 ; +} + +static int omap3_spi_set_mode (struct udevice *bus,uint mode) +{ +return 0 ; +} + +static const struct dm_spi_ops omap3_spi_ops = { + .claim_bus = omap3_spi_claim_bus, + .release_bus = omap3_spi_release_bus, + .set_wordlen = omap3_spi_set_wordlen, + .xfer = omap3_spi_xfer, + .set_speed = omap3_spi_set_speed, + .set_mode = omap3_spi_set_mode, +/* +* cs_info is not needed, since we require all chip selects to be +* in the device tree explicitly +*/ +}; + +static const struct udevice_id omap3_spi_ids[] = { + { .compatible ="ti,omap2-mcspi" }, + { .compatible ="ti,omap4-mcspi" }, + { } +}; + +U_BOOT_DRIVER (omap3_spi) = { + .name ="omap3_spi" , + .id =UCLASS_SPI , + .of_match = omap3_spi_ids, + .probe = omap3_spi_probe, + .ops = &omap3_spi_ops, + .priv_auto_alloc_size =sizeof (struct omap3_spi_priv ), + .probe = omap3_spi_probe, +}; +#endif
Signature · 1 line
1.9.1