Skip to contentSkip to conversation

mmc: fsl: reset to normal boot mode when eMMC fast boot

PATCH Superseded Peng Fan 4 participants 13 messages Apr 26, 2016 – Aug 8, 2016 MMC, SD and SDIO

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore

Peng Fan

author
#0 lore raw

PATCH 1/3 mmc: fsl: reset to normal boot mode when eMMC fast boot

When booting in eMMC fast boot, MMC host does not exit from boot mode after bootrom loading image. So the first command 'CMD0' sent in uboot will pull down the CMD line to low and cause errors.

This patch cleans the MMC boot register in "mmc_init" to put the MMC host back to normal mode.

Also clear DLL_CTRL delay line settings at USDHC initialization to eliminate the pre-settings from boot rom.

Cc Pantelis Antoniou <[email protected]>
Cc York Sun <[email protected]>
Cc Stefano Babic <[email protected]>
---
 drivers/mmc/fsl_esdhc.c | 38 +++++++++++++++++++++++++++++---------
 include/fsl_esdhc.h     |  6 ++++++
 2 files changed, 35 insertions(+), 9 deletions(-)
drivers/mmc/fsl_esdhc.c +29 -9
index 65ecff5..15cd419 100644
@@ -57,21 +57,27 @@ struct fsl_esdhc {
 	uint    fevt;		/* Force event register */
 	uint    admaes;		/* ADMA error status register */
 	uint    adsaddr;	/* ADMA system address register */
-	char    reserved2[100];	/* reserved */
-	uint    vendorspec;	/* Vendor Specific register */
-	char    reserved3[56];	/* reserved */
+	char    reserved2[4];
+	uint    dllctrl;
+	uint    dllstat;
+	uint    clktunectrlstatus;
+	char    reserved3[84];
+	uint    vendorspec;
+	uint    mmcboot;
+	uint    vendorspec2;
+	char	reserved4[48];
 	uint    hostver;	/* Host controller version register */
-	char    reserved4[4];	/* reserved */
-	uint    dmaerraddr;	/* DMA error address register */
 	char    reserved5[4];	/* reserved */
-	uint    dmaerrattr;	/* DMA error attribute register */
+	uint    dmaerraddr;	/* DMA error address register */
 	char    reserved6[4];	/* reserved */
+	uint    dmaerrattr;	/* DMA error attribute register */
+	char    reserved7[4];	/* reserved */
 	uint    hostcapblt2;	/* Host controller capabilities register 2 */
-	char    reserved7[8];	/* reserved */
+	char    reserved8[8];	/* reserved */
 	uint    tcr;		/* Tuning control register */
-	char    reserved8[28];	/* reserved */
+	char    reserved9[28];	/* reserved */
 	uint    sddirctl;	/* SD direction control register */
-	char    reserved9[712];	/* reserved */
+	char    reserved10[712];/* reserved */
 	uint    scr;		/* eSDHC control register */
 };
 
@@ -618,6 +624,20 @@ static int esdhc_init(struct mmc *mmc)
 	while ((esdhc_read32(&regs->sysctl) & SYSCTL_RSTA) && --timeout)
 		udelay(1000);
 
+#if defined(CONFIG_FSL_USDHC)
+	/* RSTA doesn't reset MMC_BOOT register, so manually reset it */
+	esdhc_write32(&regs->mmcboot, 0x0);
+	/* Reset MIX_CTRL and CLK_TUNE_CTRL_STATUS regs to 0 */
+	esdhc_write32(&regs->mixctrl, 0x0);
+	esdhc_write32(&regs->clktunectrlstatus, 0x0);
+
+	/* Put VEND_SPEC to default value */
+	esdhc_write32(&regs->vendorspec, VENDORSPEC_INIT);
+
+	/* Disable DLL_CTRL delay line */
+	esdhc_write32(&regs->dllctrl, 0x0);
+#endif
+
 #ifndef ARCH_MXC
 	/* Enable cache snooping */
 	esdhc_write32(&regs->scr, 0x00000040);
include/fsl_esdhc.h +6 -0
index fa760a5..78c67c8 100644
@@ -35,6 +35,12 @@
 #define SYSCTL_RSTC		0x02000000
 #define SYSCTL_RSTD		0x04000000
 
+#define VENDORSPEC_CKEN		0x00004000
+#define VENDORSPEC_PEREN	0x00002000
+#define VENDORSPEC_HCKEN	0x00001000
+#define VENDORSPEC_IPGEN	0x00000800
+#define VENDORSPEC_INIT		0x20007809
+
 #define IRQSTAT			0x0002e030
 #define IRQSTAT_DMAE		(0x10000000)
 #define IRQSTAT_AC12E		(0x01000000)
Signature · 1 line
2.6.2
author
#1 lore raw

PATCH 2/3 fsl_esdhc: Update clock enable bits for USDHC

From: Ye Li <[email protected]>

The USDHC move the 4 clock bits CARD_CLK_SOFT_EN, IPG_PERCLK_SOFT_EN, HCLK_SOFT_EN, and IPG_CLK_SOFT_EN from sysctl register to vendorspec register. The driver uses RSTA to replace the clock gate off operation. But this is not a good solution. This is because:
1. when using RSTA, we should wait this bit to clear by itself. This is not implemeneted in the code.
2. After RSTA is set, it is recommended that the Host Driver reset the external card and reinitialize it.

So in this patch, we change to use the vendorspec registers for these bits operation.

Cc York Sun <[email protected]>
Cc Stefano Babic <[email protected]>
Cc Pantelis Antoniou <[email protected]>
---
 drivers/mmc/fsl_esdhc.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)
drivers/mmc/fsl_esdhc.c +7 -2
index 15cd419..b69c766 100644
@@ -540,7 +540,7 @@ static void set_sysctl(struct mmc *mmc, uint clock)
 	clk = (pre_div << 8) | (div << 4);
 
 #ifdef CONFIG_FSL_USDHC
-	esdhc_setbits32(&regs->sysctl, SYSCTL_RSTA);
+	esdhc_clrbits32(&regs->vendorspec, VENDORSPEC_CKEN);
 #else
 	esdhc_clrbits32(&regs->sysctl, SYSCTL_CKEN);
 #endif
@@ -550,7 +550,7 @@ static void set_sysctl(struct mmc *mmc, uint clock)
 	udelay(10000);
 
 #ifdef CONFIG_FSL_USDHC
-	esdhc_clrbits32(&regs->sysctl, SYSCTL_RSTA);
+	esdhc_setbits32(&regs->vendorspec, VENDORSPEC_PEREN | VENDORSPEC_CKEN);
 #else
 	esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_CKEN);
 #endif
@@ -645,6 +645,8 @@ static int esdhc_init(struct mmc *mmc)
 
 #ifndef CONFIG_FSL_USDHC
 	esdhc_setbits32(&regs->sysctl, SYSCTL_HCKEN | SYSCTL_IPGEN);
+#else
+	esdhc_setbits32(&regs->vendorspec, VENDORSPEC_HCKEN | VENDORSPEC_IPGEN);
 #endif
 
 	/* Set the initial clock speed */
@@ -766,6 +768,9 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv)
 #ifndef CONFIG_FSL_USDHC
 	esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
 				| SYSCTL_IPGEN | SYSCTL_CKEN);
+#else
+	esdhc_setbits32(&regs->vendorspec, VENDORSPEC_PEREN |
+			VENDORSPEC_HCKEN | VENDORSPEC_IPGEN | VENDORSPEC_CKEN);
 #endif
 
 	writel(SDHCI_IRQ_EN_BITS, &regs->irqstaten);
Signature · 1 line
2.6.2
author
#2 lore raw

PATCH 3/3 mmc: fsl: introduce wp_enable

In reply to Peng Fan

Introudce wp_enable. If want to check WPSPL, then in board code, need to set wp_enable to 1.

Take i.MX6UL for example, to some boards, they do not use WP singal, so they does not configure USDHC1_WP_SELECT_INPUT, and its default value is 0(GPIO1_IO02). However GPIO1_IO02 is muxed for i2c usage and SION bit set. So USDHC controller can always get wp signal and WPSPL shows write protect and blocks driver continuing. This is not what we want to see, so add wp_enable, and if set to 0, just omit the WPSPL checking and this does not effect normal working of usdhc controller.

To DT case, add wp_gpio, if there is wp-gpios provided in dts, wp_enable is set to 1; if no, set to 0.

Cc Pantelis Antoniou <[email protected]>
Cc York Sun <[email protected]>
Cc Stefano Babic <[email protected]>
---
 drivers/mmc/fsl_esdhc.c | 21 ++++++++++++++++++---
 include/fsl_esdhc.h     |  1 +
 2 files changed, 19 insertions(+), 3 deletions(-)
drivers/mmc/fsl_esdhc.c +18 -3
index b69c766..4dd1765 100644
@@ -92,7 +92,9 @@ struct fsl_esdhc {
  * Following is used when Driver Model is enabled for MMC
  * @dev: pointer for the device
  * @non_removable: 0: removable; 1: non-removable
+ * @wp_enable: 1: enable checking wp; 0: no check
  * @cd_gpio: gpio for card detection
+ * @wp_gpio: gpio for write protection
  */
 struct fsl_esdhc_priv {
 	struct fsl_esdhc *esdhc_regs;
@@ -102,7 +104,9 @@ struct fsl_esdhc_priv {
 	struct mmc *mmc;
 	struct udevice *dev;
 	int non_removable;
+	int wp_enable;
 	struct gpio_desc cd_gpio;
+	struct gpio_desc wp_gpio;
 };
 
 /* Return the XFERTYP flags for a given command and data packet */
@@ -246,9 +250,12 @@ static int esdhc_setup_data(struct mmc *mmc, struct mmc_data *data)
 #endif
 		if (wml_value > WML_WR_WML_MAX)
 			wml_value = WML_WR_WML_MAX_VAL;
-		if ((esdhc_read32(&regs->prsstat) & PRSSTAT_WPSPL) == 0) {
-			printf("\nThe SD card is locked. Can not write to a locked card.\n\n");
-			return TIMEOUT;
+		if (priv->wp_enable) {
+			if ((esdhc_read32(&regs->prsstat) &
+			    PRSSTAT_WPSPL) == 0) {
+				printf("\nThe SD card is locked. Can not write to a locked card.\n\n");
+				return TIMEOUT;
+			}
 		}
 
 		esdhc_clrsetbits32(&regs->wml, WML_WR_WML_MASK,
@@ -747,6 +754,7 @@ static int fsl_esdhc_cfg_to_priv(struct fsl_esdhc_cfg *cfg,
 	priv->esdhc_regs = (struct fsl_esdhc *)(unsigned long)(cfg->esdhc_base);
 	priv->bus_width = cfg->max_bus_width;
 	priv->sdhc_clk = cfg->sdhc_clk;
+	priv->wp_enable  = cfg->wp_enable;
 
 	return 0;
 };
@@ -989,6 +997,13 @@ static int fsl_esdhc_probe(struct udevice *dev)
 					   &priv->cd_gpio, GPIOD_IS_IN);
 	}
 
+	priv->wp_enable = 1;
+
+	ret = gpio_request_by_name_nodev(fdt, node, "wp-gpios", 0,
+					 &priv->wp_gpio, GPIOD_IS_IN);
+	if (ret)
+		priv->wp_enable = 0;
+
 	/*
 	 * TODO:
 	 * Because lack of clk driver, if SDHC clk is not enabled,
include/fsl_esdhc.h +1 -0
index 78c67c8..c6f4666 100644
@@ -177,6 +177,7 @@ struct fsl_esdhc_cfg {
 	phys_addr_t esdhc_base;
 	u32	sdhc_clk;
 	u8	max_bus_width;
+	u8	wp_enable;
 	struct mmc_config cfg;
 };
 
Signature · 1 line
2.6.2
#3 lore raw

PATCH 3/3 mmc: fsl: introduce wp_enable

Hi Peng,

Quoted 12 lines · Peng Fan

Introudce wp_enable. If want to check WPSPL, then in board code, need to set wp_enable to 1.

Take i.MX6UL for example, to some boards, they do not use WP singal, so they does not configure USDHC1_WP_SELECT_INPUT, and its default value is 0(GPIO1_IO02). However GPIO1_IO02 is muxed for i2c usage and SION bit set. So USDHC controller can always get wp signal and WPSPL shows write protect and blocks driver continuing. This is not what we want to see, so add wp_enable, and if set to 0, just omit the WPSPL checking and this does not effect normal working of usdhc controller.

Quoted 7 lines

To DT case, add wp_gpio, if there is wp-gpios provided in dts, wp_enable is set to 1; if no, set to 0.

Cc Pantelis Antoniou <[email protected]>
Cc York Sun <[email protected]>
Cc Stefano Babic <[email protected]>

Just saw this issue on a mx6ul pico board: after adding I2C support then the eMMC could not longer be written:

=> saveenv
Saving Environment to MMC...
Writing to MMC(0)...
The SD card is locked. Can not write to a locked card.

mmc write failed
failed

Your patch allows me to write to the eMMC succesfully:

#4 lore raw

PATCH 3/3 mmc: fsl: introduce wp_enable

Hi Peng,

Quoted 8 lines · Fabio Estevam

Just saw this issue on a mx6ul pico board: after adding I2C support then the eMMC could not longer be written:

=> saveenv
Saving Environment to MMC...
Writing to MMC(0)...
The SD card is locked. Can not write to a locked card.

Quoted 6 lines

mmc write failed
failed

Your patch allows me to write to the eMMC succesfully:

Looks like this is an issue with the MX6UL IOMUXC, not the esdhc driver itself, so maybe we should not do this change for all other SoCs.

If I manually do:
=> mw.l 20E066C 2
Then 'saveenv' works fine.

Shouldn't we fix this in the MX6UL IOMUXC code instead?

author
#5 lore raw

PATCH 3/3 mmc: fsl: introduce wp_enable

Hi Fabio,

Quoted 18 lines · Fabio Estevam

Hi Peng,

Quoted 14 lines · Fabio Estevam

Just saw this issue on a mx6ul pico board: after adding I2C support then the eMMC could not longer be written:

=> saveenv
Saving Environment to MMC...
Writing to MMC(0)...
The SD card is locked. Can not write to a locked card.

mmc write failed
failed

Your patch allows me to write to the eMMC succesfully:

Thanks. This patch set was posted some time ago.

Quoted 10 lines

Looks like this is an issue with the MX6UL IOMUXC, not the esdhc driver itself, so maybe we should not do this change for all other SoCs.

If I manually do:
=> mw.l 20E066C 2
Then 'saveenv' works fine.

Shouldn't we fix this in the MX6UL IOMUXC code instead?

No. We can not avoid such issue for now. You changed register 20e066c'value to 2 2 means "CSI_DATA04_ALT8 ? Selecting Pad: CSI_DATA04 for Mode: ALT8"

Look at "Figure 31-3. Daisy chain illustration" of i.MX6UL RM, if changed to 2, that means you let CSI_DATA04 pad goes into usdhc1_wp.

select input can not be closed or disabled, which will cause issues like what you met. Even worse, some one may need to redesign their board to avoid pin conflict.

Regards,
Peng.

#6 lore raw

PATCH 3/3 mmc: fsl: introduce wp_enable

Hi Peng,

Quoted 5 lines · Peng Fan

No. We can not avoid such issue for now. You changed register 20e066c'value to 2 2 means "CSI_DATA04_ALT8 ? Selecting Pad: CSI_DATA04 for Mode: ALT8"

Look at "Figure 31-3. Daisy chain illustration" of i.MX6UL RM, if changed to 2, that means you let CSI_DATA04 pad goes into usdhc1_wp.

Yes, this was just a quick hack. I am not proposing this workaround :-)

Quoted 3 lines

select input can not be closed or disabled, which will cause issues like what you met. Even worse, some one may need to redesign their board to avoid pin conflict.

Yes, I understood the problem and don't have any alternative suggestion at the moment.

Pantelis/Stefano/Tom/York,

Any feedback on this series, please?

author
#9 lore raw

PATCH 3/3 mmc: fsl: introduce wp_enable

Hi Fabio,

Quoted 9 lines · Fabio Estevam
Quoted 5 lines · Peng Fan
Quoted 3 lines
Quoted 3 lines

Your patch allows me to write to the eMMC succesfully:

Thanks. This patch set was posted some time ago.

Care to resend this series, please?

Ok. I will resend this series with your tested-by tag.

Thanks,
Peng.

Quoted 2 lines

Thanks

#7 lore raw

PATCH 3/3 mmc: fsl: introduce wp_enable

In reply to Fabio Estevam
Quoted 16 lines · Fabio Estevam

Hi Peng,

Quoted 5 lines · Peng Fan

No. We can not avoid such issue for now. You changed register 20e066c'value to 2 2 means "CSI_DATA04_ALT8 ? Selecting Pad: CSI_DATA04 for Mode: ALT8"

Look at "Figure 31-3. Daisy chain illustration" of i.MX6UL RM, if changed to 2, that means you let CSI_DATA04 pad goes into usdhc1_wp.

Yes, this was just a quick hack. I am not proposing this workaround :-)

Quoted 3 lines

select input can not be closed or disabled, which will cause issues like what you met. Even worse, some one may need to redesign their board to avoid pin conflict.

Quoted 7 lines

Yes, I understood the problem and don't have any alternative suggestion at the moment.

Pantelis/Stefano/Tom/York,

Any feedback on this series, please?

It looks good to me, but I didn't test it.

York

#10 lore raw

PATCH 1/3 mmc: fsl: reset to normal boot mode when eMMC fast boot

In reply to Peng Fan

Hi Peng,

Quoted 7 lines · Peng Fan

When booting in eMMC fast boot, MMC host does not exit from boot mode after bootrom loading image. So the first command 'CMD0' sent in uboot will pull down the CMD line to low and cause errors.

This patch cleans the MMC boot register in "mmc_init" to put the MMC host back to normal mode.

Could you resend the patch-set [1/3 - 3/3] on latest u-boot? After that, I will check..

Best Regards,
Jaehoon Chung

Quoted 93 lines

Also clear DLL_CTRL delay line settings at USDHC initialization to eliminate the pre-settings from boot rom.

Cc Pantelis Antoniou <[email protected]>
Cc York Sun <[email protected]>
Cc Stefano Babic <[email protected]>
---
 drivers/mmc/fsl_esdhc.c | 38 +++++++++++++++++++++++++++++---------
 include/fsl_esdhc.h     |  6 ++++++
 2 files changed, 35 insertions(+), 9 deletions(-)
drivers/mmc/fsl_esdhc.c +29 -9
index 65ecff5..15cd419 100644
@@ -57,21 +57,27 @@ struct fsl_esdhc {
 	uint    fevt;		/* Force event register */
 	uint    admaes;		/* ADMA error status register */
 	uint    adsaddr;	/* ADMA system address register */
-	char    reserved2[100];	/* reserved */
-	uint    vendorspec;	/* Vendor Specific register */
-	char    reserved3[56];	/* reserved */
+	char    reserved2[4];
+	uint    dllctrl;
+	uint    dllstat;
+	uint    clktunectrlstatus;
+	char    reserved3[84];
+	uint    vendorspec;
+	uint    mmcboot;
+	uint    vendorspec2;
+	char	reserved4[48];
 	uint    hostver;	/* Host controller version register */
-	char    reserved4[4];	/* reserved */
-	uint    dmaerraddr;	/* DMA error address register */
 	char    reserved5[4];	/* reserved */
-	uint    dmaerrattr;	/* DMA error attribute register */
+	uint    dmaerraddr;	/* DMA error address register */
 	char    reserved6[4];	/* reserved */
+	uint    dmaerrattr;	/* DMA error attribute register */
+	char    reserved7[4];	/* reserved */
 	uint    hostcapblt2;	/* Host controller capabilities register 2 */
-	char    reserved7[8];	/* reserved */
+	char    reserved8[8];	/* reserved */
 	uint    tcr;		/* Tuning control register */
-	char    reserved8[28];	/* reserved */
+	char    reserved9[28];	/* reserved */
 	uint    sddirctl;	/* SD direction control register */
-	char    reserved9[712];	/* reserved */
+	char    reserved10[712];/* reserved */
 	uint    scr;		/* eSDHC control register */
 };
 
@@ -618,6 +624,20 @@ static int esdhc_init(struct mmc *mmc)
 	while ((esdhc_read32(&regs->sysctl) & SYSCTL_RSTA) && --timeout)
 		udelay(1000);
 
+#if defined(CONFIG_FSL_USDHC)
+	/* RSTA doesn't reset MMC_BOOT register, so manually reset it */
+	esdhc_write32(&regs->mmcboot, 0x0);
+	/* Reset MIX_CTRL and CLK_TUNE_CTRL_STATUS regs to 0 */
+	esdhc_write32(&regs->mixctrl, 0x0);
+	esdhc_write32(&regs->clktunectrlstatus, 0x0);
+
+	/* Put VEND_SPEC to default value */
+	esdhc_write32(&regs->vendorspec, VENDORSPEC_INIT);
+
+	/* Disable DLL_CTRL delay line */
+	esdhc_write32(&regs->dllctrl, 0x0);
+#endif
+
 #ifndef ARCH_MXC
 	/* Enable cache snooping */
 	esdhc_write32(&regs->scr, 0x00000040);
include/fsl_esdhc.h +6 -0
index fa760a5..78c67c8 100644
@@ -35,6 +35,12 @@
 #define SYSCTL_RSTC		0x02000000
 #define SYSCTL_RSTD		0x04000000
 
+#define VENDORSPEC_CKEN		0x00004000
+#define VENDORSPEC_PEREN	0x00002000
+#define VENDORSPEC_HCKEN	0x00001000
+#define VENDORSPEC_IPGEN	0x00000800
+#define VENDORSPEC_INIT		0x20007809
+
 #define IRQSTAT			0x0002e030
 #define IRQSTAT_DMAE		(0x10000000)
 #define IRQSTAT_AC12E		(0x01000000)
author
#11 lore raw

PATCH 1/3 mmc: fsl: reset to normal boot mode when eMMC fast boot

Hi Jaehoon,

Quoted 8 lines · Jaehoon Chung

Hi Peng,

Quoted 5 lines · Peng Fan

When booting in eMMC fast boot, MMC host does not exit from boot mode after bootrom loading image. So the first command 'CMD0' sent in uboot will pull down the CMD line to low and cause errors.

Quoted 5 lines
Quoted 2 lines

This patch cleans the MMC boot register in "mmc_init" to put the MMC host back to normal mode.

Could you resend the patch-set [1/3 - 3/3] on latest u-boot? After that, I will check..

This patch set already merged through York's tree.

Thanks,
Peng.

Quoted 98 lines

Best Regards,
Jaehoon Chung

Quoted 93 lines

Also clear DLL_CTRL delay line settings at USDHC initialization to eliminate the pre-settings from boot rom.

Cc Pantelis Antoniou <[email protected]>
Cc York Sun <[email protected]>
Cc Stefano Babic <[email protected]>
---
 drivers/mmc/fsl_esdhc.c | 38 +++++++++++++++++++++++++++++---------
 include/fsl_esdhc.h     |  6 ++++++
 2 files changed, 35 insertions(+), 9 deletions(-)
drivers/mmc/fsl_esdhc.c +29 -9
index 65ecff5..15cd419 100644
@@ -57,21 +57,27 @@ struct fsl_esdhc {
 	uint    fevt;		/* Force event register */
 	uint    admaes;		/* ADMA error status register */
 	uint    adsaddr;	/* ADMA system address register */
-	char    reserved2[100];	/* reserved */
-	uint    vendorspec;	/* Vendor Specific register */
-	char    reserved3[56];	/* reserved */
+	char    reserved2[4];
+	uint    dllctrl;
+	uint    dllstat;
+	uint    clktunectrlstatus;
+	char    reserved3[84];
+	uint    vendorspec;
+	uint    mmcboot;
+	uint    vendorspec2;
+	char	reserved4[48];
 	uint    hostver;	/* Host controller version register */
-	char    reserved4[4];	/* reserved */
-	uint    dmaerraddr;	/* DMA error address register */
 	char    reserved5[4];	/* reserved */
-	uint    dmaerrattr;	/* DMA error attribute register */
+	uint    dmaerraddr;	/* DMA error address register */
 	char    reserved6[4];	/* reserved */
+	uint    dmaerrattr;	/* DMA error attribute register */
+	char    reserved7[4];	/* reserved */
 	uint    hostcapblt2;	/* Host controller capabilities register 2 */
-	char    reserved7[8];	/* reserved */
+	char    reserved8[8];	/* reserved */
 	uint    tcr;		/* Tuning control register */
-	char    reserved8[28];	/* reserved */
+	char    reserved9[28];	/* reserved */
 	uint    sddirctl;	/* SD direction control register */
-	char    reserved9[712];	/* reserved */
+	char    reserved10[712];/* reserved */
 	uint    scr;		/* eSDHC control register */
 };
 
@@ -618,6 +624,20 @@ static int esdhc_init(struct mmc *mmc)
 	while ((esdhc_read32(&regs->sysctl) & SYSCTL_RSTA) && --timeout)
 		udelay(1000);
 
+#if defined(CONFIG_FSL_USDHC)
+	/* RSTA doesn't reset MMC_BOOT register, so manually reset it */
+	esdhc_write32(&regs->mmcboot, 0x0);
+	/* Reset MIX_CTRL and CLK_TUNE_CTRL_STATUS regs to 0 */
+	esdhc_write32(&regs->mixctrl, 0x0);
+	esdhc_write32(&regs->clktunectrlstatus, 0x0);
+
+	/* Put VEND_SPEC to default value */
+	esdhc_write32(&regs->vendorspec, VENDORSPEC_INIT);
+
+	/* Disable DLL_CTRL delay line */
+	esdhc_write32(&regs->dllctrl, 0x0);
+#endif
+
 #ifndef ARCH_MXC
 	/* Enable cache snooping */
 	esdhc_write32(&regs->scr, 0x00000040);
include/fsl_esdhc.h +6 -0
index fa760a5..78c67c8 100644
@@ -35,6 +35,12 @@
 #define SYSCTL_RSTC		0x02000000
 #define SYSCTL_RSTD		0x04000000
 
+#define VENDORSPEC_CKEN		0x00004000
+#define VENDORSPEC_PEREN	0x00002000
+#define VENDORSPEC_HCKEN	0x00001000
+#define VENDORSPEC_IPGEN	0x00000800
+#define VENDORSPEC_INIT		0x20007809
+
 #define IRQSTAT			0x0002e030
 #define IRQSTAT_DMAE		(0x10000000)
 #define IRQSTAT_AC12E		(0x01000000)
#12 lore raw

PATCH 1/3 mmc: fsl: reset to normal boot mode when eMMC fast boot

Quoted 10 lines · Peng Fan

Hi Jaehoon,

Quoted 8 lines · Jaehoon Chung

Hi Peng,

Quoted 5 lines · Peng Fan

When booting in eMMC fast boot, MMC host does not exit from boot mode after bootrom loading image. So the first command 'CMD0' sent in uboot will pull down the CMD line to low and cause errors.

Quoted 7 lines
Quoted 5 lines
Quoted 2 lines

This patch cleans the MMC boot register in "mmc_init" to put the MMC host back to normal mode.

Could you resend the patch-set [1/3 - 3/3] on latest u-boot? After that, I will check..

This patch set already merged through York's tree.

Thanks for noticing!

Best Regards,
Jaehoon Chung

Quoted 105 lines

Thanks,
Peng.

Quoted 98 lines

Best Regards,
Jaehoon Chung

Quoted 93 lines

Also clear DLL_CTRL delay line settings at USDHC initialization to eliminate the pre-settings from boot rom.

Cc Pantelis Antoniou <[email protected]>
Cc York Sun <[email protected]>
Cc Stefano Babic <[email protected]>
---
 drivers/mmc/fsl_esdhc.c | 38 +++++++++++++++++++++++++++++---------
 include/fsl_esdhc.h     |  6 ++++++
 2 files changed, 35 insertions(+), 9 deletions(-)
drivers/mmc/fsl_esdhc.c +29 -9
index 65ecff5..15cd419 100644
@@ -57,21 +57,27 @@ struct fsl_esdhc {
 	uint    fevt;		/* Force event register */
 	uint    admaes;		/* ADMA error status register */
 	uint    adsaddr;	/* ADMA system address register */
-	char    reserved2[100];	/* reserved */
-	uint    vendorspec;	/* Vendor Specific register */
-	char    reserved3[56];	/* reserved */
+	char    reserved2[4];
+	uint    dllctrl;
+	uint    dllstat;
+	uint    clktunectrlstatus;
+	char    reserved3[84];
+	uint    vendorspec;
+	uint    mmcboot;
+	uint    vendorspec2;
+	char	reserved4[48];
 	uint    hostver;	/* Host controller version register */
-	char    reserved4[4];	/* reserved */
-	uint    dmaerraddr;	/* DMA error address register */
 	char    reserved5[4];	/* reserved */
-	uint    dmaerrattr;	/* DMA error attribute register */
+	uint    dmaerraddr;	/* DMA error address register */
 	char    reserved6[4];	/* reserved */
+	uint    dmaerrattr;	/* DMA error attribute register */
+	char    reserved7[4];	/* reserved */
 	uint    hostcapblt2;	/* Host controller capabilities register 2 */
-	char    reserved7[8];	/* reserved */
+	char    reserved8[8];	/* reserved */
 	uint    tcr;		/* Tuning control register */
-	char    reserved8[28];	/* reserved */
+	char    reserved9[28];	/* reserved */
 	uint    sddirctl;	/* SD direction control register */
-	char    reserved9[712];	/* reserved */
+	char    reserved10[712];/* reserved */
 	uint    scr;		/* eSDHC control register */
 };
 
@@ -618,6 +624,20 @@ static int esdhc_init(struct mmc *mmc)
 	while ((esdhc_read32(&regs->sysctl) & SYSCTL_RSTA) && --timeout)
 		udelay(1000);
 
+#if defined(CONFIG_FSL_USDHC)
+	/* RSTA doesn't reset MMC_BOOT register, so manually reset it */
+	esdhc_write32(&regs->mmcboot, 0x0);
+	/* Reset MIX_CTRL and CLK_TUNE_CTRL_STATUS regs to 0 */
+	esdhc_write32(&regs->mixctrl, 0x0);
+	esdhc_write32(&regs->clktunectrlstatus, 0x0);
+
+	/* Put VEND_SPEC to default value */
+	esdhc_write32(&regs->vendorspec, VENDORSPEC_INIT);
+
+	/* Disable DLL_CTRL delay line */
+	esdhc_write32(&regs->dllctrl, 0x0);
+#endif
+
 #ifndef ARCH_MXC
 	/* Enable cache snooping */
 	esdhc_write32(&regs->scr, 0x00000040);
include/fsl_esdhc.h +6 -0
index fa760a5..78c67c8 100644
@@ -35,6 +35,12 @@
 #define SYSCTL_RSTC		0x02000000
 #define SYSCTL_RSTD		0x04000000
 
+#define VENDORSPEC_CKEN		0x00004000
+#define VENDORSPEC_PEREN	0x00002000
+#define VENDORSPEC_HCKEN	0x00001000
+#define VENDORSPEC_IPGEN	0x00000800
+#define VENDORSPEC_INIT		0x20007809
+
 #define IRQSTAT			0x0002e030
 #define IRQSTAT_DMAE		(0x10000000)
 #define IRQSTAT_AC12E		(0x01000000)