Skip to contentSkip to conversation

mx35, flea3: updates for the imx35 based flea3 board

PATCH New Heiko Schocher 2 participants 6 messages Oct 17, 2016 – Nov 14, 2016

lore
Share & tools
lore
#0 lore raw

cover mx35, flea3: updates for the imx35 based flea3 board

post some small updates for the imx35 based flea3 board
- add DT support
- factorize SDRAM setup
- add GPIO setup
- adjust default environment

Heiko Schocher (2):
mx35: add DT support to flea3 board
mx35: adjust default environment for flea3 board

Stefano Babic (2):
mx35: factorize SDRAM setup in flea3
mx35: add GPIO setup on flea3 board

 board/CarMediaLab/flea3/flea3.c | 124 +++++++++++-----------------------------
 configs/flea3_defconfig         |   4 ++
 include/configs/flea3.h         |   9 ++-
 3 files changed, 42 insertions(+), 95 deletions(-)
Signature · 1 line
2.5.5
#1 lore raw

PATCH 1/4 mx35: add DT support to flea3 board

---

 board/CarMediaLab/flea3/flea3.c | 24 ++++++++++++++++++++++++
 configs/flea3_defconfig         |  4 ++++
 2 files changed, 28 insertions(+)
board/CarMediaLab/flea3/flea3.c +24 -0
index 2463077..be42863 100644
@@ -19,6 +19,9 @@
 #include <asm/gpio.h>
 #include <asm/arch/sys_proto.h>
 #include <netdev.h>
+#include <fdt_support.h>
+#include <mtd_node.h>
+#include <jffs2/load_kernel.h>
 
 #ifndef CONFIG_BOARD_EARLY_INIT_F
 #error "CONFIG_BOARD_EARLY_INIT_F must be set for this board"
@@ -276,3 +279,24 @@ u32 get_board_rev(void)
 
 	return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
 }
+
+/*
+ * called prior to booting kernel or by 'fdt boardsetup' command
+ *
+ */
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	struct node_info nodes[] = {
+		{ "physmap-flash.0", MTD_DEV_TYPE_NOR, },  /* NOR flash */
+		{ "mxc_nand", MTD_DEV_TYPE_NAND, }, /* NAND flash */
+	};
+
+	if (getenv("fdt_noauto")) {
+		puts("   Skiping ft_board_setup (fdt_noauto defined)\n");
+		return 0;
+	}
+
+	fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes));
+
+	return 0;
+}
configs/flea3_defconfig +4 -0
index 7aa1ba8..c5ccbd6 100644
@@ -1,6 +1,7 @@
 CONFIG_ARM=y
 CONFIG_TARGET_FLEA3=y
 CONFIG_FIT=y
+CONFIG_OF_BOARD_SETUP=y
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_HUSH_PARSER=y
@@ -12,3 +13,6 @@ CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
+CONFIG_OF_LIBFDT=y
+CONFIG_FDT_FIXUP_PARTITIONS=y
+# CONFIG_EFI_LOADER is not set
Signature · 1 line
2.5.5
#2 lore raw

PATCH 2/4 mx35: factorize SDRAM setup in flea3

In reply to Heiko Schocher

From: Stefano Babic <[email protected]>

Drop local function to setup SDRAM controller
and use the common one for i.MX35.

---

 board/CarMediaLab/flea3/flea3.c | 93 ++---------------------------------------
 1 file changed, 3 insertions(+), 90 deletions(-)
board/CarMediaLab/flea3/flea3.c +3 -90
index be42863..ca3e44b 100644
@@ -30,18 +30,6 @@
 #define CCM_CCMR_CONFIG		0x003F4208
 
 #define ESDCTL_DDR2_CONFIG	0x007FFC3F
-#define ESDCTL_0x92220000	0x92220000
-#define ESDCTL_0xA2220000	0xA2220000
-#define ESDCTL_0xB2220000	0xB2220000
-#define ESDCTL_0x82228080	0x82228080
-#define ESDCTL_DDR2_EMR2	0x04000000
-#define ESDCTL_DDR2_EMR3	0x06000000
-#define ESDCTL_PRECHARGE	0x00000400
-#define ESDCTL_DDR2_EN_DLL	0x02000400
-#define ESDCTL_DDR2_RESET_DLL	0x00000333
-#define ESDCTL_DDR2_MR		0x00000233
-#define ESDCTL_DDR2_OCD_DEFAULT 0x02000780
-#define ESDCTL_DELAY_LINE5	0x00F49F00
 
 static inline void dram_wait(unsigned int count)
 {
@@ -61,83 +49,6 @@ int dram_init(void)
 	return 0;
 }
 
-static void board_setup_sdram_bank(u32 start_address)
-
-{
-	struct esdc_regs *esdc = (struct esdc_regs *)ESDCTL_BASE_ADDR;
-	u32 *cfg_reg, *ctl_reg;
-	u32 val;
-
-	switch (start_address) {
-	case CSD0_BASE_ADDR:
-		cfg_reg = &esdc->esdcfg0;
-		ctl_reg = &esdc->esdctl0;
-		break;
-	case CSD1_BASE_ADDR:
-		cfg_reg = &esdc->esdcfg1;
-		ctl_reg = &esdc->esdctl1;
-		break;
-	default:
-		return;
-	}
-
-	/* Initialize MISC register for DDR2 */
-	val = ESDC_MISC_RST | ESDC_MISC_MDDR_EN | ESDC_MISC_MDDR_DL_RST |
-		ESDC_MISC_DDR_EN | ESDC_MISC_DDR2_EN;
-	writel(val, &esdc->esdmisc);
-	val &= ~(ESDC_MISC_RST | ESDC_MISC_MDDR_DL_RST);
-	writel(val, &esdc->esdmisc);
-
-	/*
-	 * according to DDR2 specs, wait a while before
-	 * the PRECHARGE_ALL command
-	 */
-	dram_wait(0x20000);
-
-	/* Load DDR2 config and timing */
-	writel(ESDCTL_DDR2_CONFIG, cfg_reg);
-
-	/* Precharge ALL */
-	writel(ESDCTL_0x92220000,
-		ctl_reg);
-	writel(0xda, start_address + ESDCTL_PRECHARGE);
-
-	/* Load mode */
-	writel(ESDCTL_0xB2220000,
-		ctl_reg);
-	writeb(0xda, start_address + ESDCTL_DDR2_EMR2); /* EMRS2 */
-	writeb(0xda, start_address + ESDCTL_DDR2_EMR3); /* EMRS3 */
-	writeb(0xda, start_address + ESDCTL_DDR2_EN_DLL); /* Enable DLL */
-	writeb(0xda, start_address + ESDCTL_DDR2_RESET_DLL); /* Reset DLL */
-
-	/* Precharge ALL */
-	writel(ESDCTL_0x92220000,
-		ctl_reg);
-	writel(0xda, start_address + ESDCTL_PRECHARGE);
-
-	/* Set mode auto refresh : at least two refresh are required */
-	writel(ESDCTL_0xA2220000,
-		ctl_reg);
-	writel(0xda, start_address);
-	writel(0xda, start_address);
-
-	writel(ESDCTL_0xB2220000,
-		ctl_reg);
-	writeb(0xda, start_address + ESDCTL_DDR2_MR);
-	writeb(0xda, start_address + ESDCTL_DDR2_OCD_DEFAULT);
-
-	/* OCD mode exit */
-	writeb(0xda, start_address + ESDCTL_DDR2_EN_DLL); /* Enable DLL */
-
-	/* Set normal mode */
-	writel(ESDCTL_0x82228080,
-		ctl_reg);
-
-	dram_wait(0x20000);
-
-	/* Do not set delay lines, only for MDDR */
-}
-
 static void board_setup_sdram(void)
 {
 	struct esdc_regs *esdc = (struct esdc_regs *)ESDCTL_BASE_ADDR;
@@ -146,7 +57,9 @@ static void board_setup_sdram(void)
 	writel(0x2000, &esdc->esdctl0);
 	writel(0x2000, &esdc->esdctl1);
 
-	board_setup_sdram_bank(CSD0_BASE_ADDR);
+
+	mx3_setup_sdram_bank(CSD0_BASE_ADDR, ESDCTL_DDR2_CONFIG,
+			     13, 10, 2, 0x8080);
 }
 
 static void setup_iomux_uart3(void)
Signature · 1 line
2.5.5
#3 lore raw

PATCH 3/4 mx35: add GPIO setup on flea3 board

In reply to Heiko Schocher

From: Stefano Babic <[email protected]>

Hardware revision "e" of the board introduces a GPIO to reduce power consumption in stand-by mode. This must be enable (active low) at the startup for normal behaviour.

---

 board/CarMediaLab/flea3/flea3.c | 7 +++++++
 1 file changed, 7 insertions(+)
board/CarMediaLab/flea3/flea3.c +7 -0
index ca3e44b..3cd4dc9 100644
@@ -122,6 +122,8 @@ static void setup_iomux_fec(void)
 		MX35_PAD_FEC_TDATA2__FEC_TDATA_2,
 		MX35_PAD_FEC_RDATA3__FEC_RDATA_3,
 		MX35_PAD_FEC_TDATA3__FEC_TDATA_3,
+		/* GPIO used to power off ethernet */
+		MX35_PAD_STXFS4__GPIO2_31,
 	};
 
 	/* setup pins for FEC */
@@ -183,6 +185,11 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 
+	/* Enable power for ethernet */
+	gpio_direction_output(63, 0);
+
+	udelay(2000);
+
 	return 0;
 }
 
Signature · 1 line
2.5.5
#4 lore raw

PATCH 4/4 mx35: adjust default environment for flea3 board

In reply to Heiko Schocher

---

 include/configs/flea3.h | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)
include/configs/flea3.h +4 -5
index 11d9391..0f7b3c8 100644
@@ -101,10 +101,9 @@
 #define CONFIG_CMDLINE_EDITING
 
 #define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE	512	/* Console I/O Buffer Size */
 /* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_MAXARGS	32	/* max number of command args */
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
 
 #define CONFIG_SYS_MEMTEST_START	0	/* memtest works on */
@@ -227,8 +226,8 @@
 	"u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"		\
 	"load=tftp ${loadaddr} ${u-boot}\0"				\
 	"uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0"		\
-	"update=protect off ${uboot_addr} +40000;"			\
-		"erase ${uboot_addr} +40000;"				\
+	"update=protect off ${uboot_addr} +80000;"			\
+		"erase ${uboot_addr} +80000;"				\
 		"cp.b ${loadaddr} ${uboot_addr} ${filesize}\0"		\
 	"upd=if run load;then echo Updating u-boot;if run update;"	\
 		"then echo U-Boot updated;"				\
Signature · 1 line
2.5.5
#5 lore raw

cover mx35, flea3: updates for the imx35 based flea3 board

In reply to Heiko Schocher
Quoted 11 lines · Heiko Schocher

post some small updates for the imx35 based flea3 board
- add DT support
- factorize SDRAM setup
- add GPIO setup
- adjust default environment

Heiko Schocher (2):
mx35: add DT support to flea3 board
mx35: adjust default environment for flea3 board

Quoted 9 lines

Stefano Babic (2):
mx35: factorize SDRAM setup in flea3
mx35: add GPIO setup on flea3 board

 board/CarMediaLab/flea3/flea3.c | 124 +++++++++++-----------------------------
 configs/flea3_defconfig         |   4 ++
 include/configs/flea3.h         |   9 ++-
 3 files changed, 42 insertions(+), 95 deletions(-)

Applied to u-boot-imx, -next branch, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================