kdb: Fix locking in vkdb_printf()
Subsystems (2)
Petr Mladek
maintainercover kdb: Fix locking in vkdb_printf()
I have been asked whether it is safe to call vkdb_printf() from vprintk_nmi() in NMI context. It seems that it is not safe. Well, is not a big deal.
But I have noticed suspicious patterns when looking at the vkdb_printf() locking code and prepared two patches that should avoid some possible races.
Please, note that I am not familiar with the kdb implementation. I hope that I have got the requested behavior right. I did some basic testing and did not found any problem. But I am sure that I did not test all usecases.
Petr Mladek (2):
kdb: Properly synchronize vkdb_printf() calls with other CPUs
kdb: Call vkdb_printf() from vprintk_default() only when wanted
include/linux/kdb.h | 1 + kernel/debug/kdb/kdb_io.c | 41 +++++++++++++++++------------------------ kernel/debug/kdb/kdb_private.h | 1 - kernel/printk/printk.c | 4 +++- 4 files changed, 21 insertions(+), 26 deletions(-)
Signature · 1 line
1.8.5.6
Petr Mladek
maintainerPATCH 1/2 kdb: Properly synchronize vkdb_printf() calls with other CPUs
kdb_printf_lock does not prevent other CPUs from entering the critical section because it is ignored when KDB_STATE_PRINTF_LOCK is set.
The problematic situation might look like:
CPU0 CPU1
vkdb_printf()
if (!KDB_STATE(PRINTF_LOCK))
KDB_STATE_SET(PRINTF_LOCK);
spin_lock_irqsave(&kdb_printf_lock, flags);
vkdb_printf()
if (!KDB_STATE(PRINTF_LOCK))BANG: The PRINTF_LOCK state is set and CPU1 is entering the critical section without spinning on the lock.
The problem is that the code tries to implement locking using two state variables that are not handled atomically. Well, we need a custom locking because we want to allow reentering the critical section on the very same CPU.
Let's use solution from Petr Zijlstra that was proposed for a similar scenario, see
https://lkml.kernel.org/r/[email protected]
This patch uses the same trick with cmpxchg(). The only difference is that we want to handle only recursion from the same context and therefore we disable interrupts.
In addition, we want to be on the safe side and update "kdb_event" outside of the critical section. Therefore we need an extra barrier before it gets decremented.
Note that "kdb_event" is always incremented/decremented now. But it should not cause any harm. The important information is whether it is zero or not.
Finally, KDB_STATE_PRINTF_LOCK is removed. In fact, we are not able to set it a non-racy way.
--- kernel/debug/kdb/kdb_io.c | 36 +++++++++++++++++------------------- kernel/debug/kdb/kdb_private.h | 1 - 2 files changed, 17 insertions(+), 20 deletions(-)
kernel/debug/kdb/kdb_io.c +17 -19
@@ -555,16 +555,16 @@ int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap)int colcount;int logging, saved_loglevel =0 ;int saved_trap_printk; -int got_printf_lock =0 ;int retlen =0 ;int fnd, len; +int this_cpu, old_cpu; +static int kdb_printf_cpu =-1 ;char *cp, *cp2, *cphold =NULL , replaced_byte =' ' ;char *moreprompt ="more> " ;struct console *c = console_drivers; -static DEFINE_SPINLOCK (kdb_printf_lock);unsigned long uninitialized_var (flags ); -preempt_disable (); +local_irq_save (flags); saved_trap_printk = kdb_trap_printk; kdb_trap_printk =0 ;
@@ -572,13 +572,14 @@ int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap)* But if any cpu goes recursive in kdb, just print the output, * even if it is interleaved with any other text. */ -if (!KDB_STATE (PRINTF_LOCK )) { -KDB_STATE_SET (PRINTF_LOCK ); -spin_lock_irqsave (&kdb_printf_lock, flags); - got_printf_lock =1 ; -atomic_inc (&kdb_event); - }else { -__acquire (kdb_printf_lock); + this_cpu =smp_processor_id (); +atomic_inc (&kdb_event); +for (;;) { + old_cpu =cmpxchg (&kdb_printf_cpu,-1 , this_cpu); +if (old_cpu ==-1 || old_cpu == this_cpu) +break ; + +cpu_relax (); } diag =kdbgetintenv ("LINES" , &linecount);
@@ -847,16 +848,13 @@ int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap) suspend_grep =0 ;/* end of what may have been a recursive call */ if (logging) console_loglevel = saved_loglevel; -if (KDB_STATE (PRINTF_LOCK ) && got_printf_lock) { - got_printf_lock =0 ; -spin_unlock_irqrestore (&kdb_printf_lock, flags); -KDB_STATE_CLEAR (PRINTF_LOCK ); -atomic_dec (&kdb_event); - }else { -__release (kdb_printf_lock); - } +/* kdb_printf_cpu locked the code above. */ +smp_store_release (&kdb_printf_cpu, old_cpu); +/* Update kdb_event around the locked section. */ +smp_mb__before_atomic (); +atomic_dec (&kdb_event); kdb_trap_printk = saved_trap_printk; -preempt_enable (); +local_irq_restore (flags);return retlen; }
kernel/debug/kdb/kdb_private.h +0 -1
@@ -132,7 +132,6 @@ extern int kdbgetaddrarg(int, const char **, int*, unsigned long *,#define KDB_STATE_PAGER 0x00000400/* pager is available */ #define KDB_STATE_GO_SWITCH 0x00000800/* go is switching * back to initial cpu */ -#define KDB_STATE_PRINTF_LOCK 0x00001000/* Holds kdb_printf lock */ #define KDB_STATE_WAIT_IPI 0x00002000/* Waiting for kdb_ipi() NMI */ #define KDB_STATE_RECURSE 0x00004000/* Recursive entry to kdb */ #define KDB_STATE_IP_ADJUSTED 0x00008000/* Restart IP has been
Signature · 1 line
1.8.5.6
Re: [PATCH 1/2] kdb: Properly synchronize vkdb_printf() calls with other CPUs
Quoted 40 lines · Petr Mladek
kdb_printf_lockdoes not prevent other CPUs from entering the critical section because it is ignored whenKDB_STATE_PRINTF_LOCKis set.The problematic situation might look like:
...
Signed-off-by Petr Mladek <[email protected]>--- kernel/debug/kdb/kdb_io.c | 36 +++++++++++++++++------------------- kernel/debug/kdb/kdb_private.h | 1 - 2 files changed, 17 insertions(+), 20 deletions(-)kernel/debug/kdb/kdb_io.c +3
-3@@ -555,16 +555,16 @@ int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap)int colcount;int logging, saved_loglevel =0 ;int saved_trap_printk; -int got_printf_lock =0 ;int retlen =0 ;int fnd, len; +int this_cpu, old_cpu; +static int kdb_printf_cpu =-1 ;char *cp, *cp2, *cphold =NULL , replaced_byte =' ' ;char *moreprompt ="more> " ;struct console *c = console_drivers; -static DEFINE_SPINLOCK (kdb_printf_lock);unsigned long uninitialized_var (flags ); -preempt_disable (); +local_irq_save (flags); saved_trap_printk = kdb_trap_printk; kdb_trap_printk =0 ;@@ -572,13 +572,14 @@ int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap)* But if any cpu goes recursive in kdb, just print the output, * even if it is interleaved with any other text.
kernel/debug/kdb/kdb_io.c int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap) · line 576
Quoted 10 lines
kernel/debug/kdb/kdb_io.c +2
-7*/ -if (!KDB_STATE (PRINTF_LOCK )) { -KDB_STATE_SET (PRINTF_LOCK ); -spin_lock_irqsave (&kdb_printf_lock, flags); - got_printf_lock =1 ; -atomic_inc (&kdb_event); - }else { -__acquire (kdb_printf_lock); + this_cpu =smp_processor_id (); +atomic_inc (&kdb_event);
When reviewing I noticed that, when we recursively enter, kdb_event is handled differently after this patch so I wanted to figure out if this alternative handling of kdb_event was safe.
In the end I concluded it is safe but that's mostly because the *only* thing we ever seem to do with kdb_event is increment and decrement it. So perhaps adding another patch at the front of this series to nuke this variable would be worthwhile (whilst making this patch easier to read).
However, your choice and, either way:
Daniel.
Petr Mladek
maintainerRe: [PATCH 1/2] kdb: Properly synchronize vkdb_printf() calls with other CPUs
Quoted 56 lines · Daniel Thompson
Quoted 40 lines · Petr Mladek
kdb_printf_lockdoes not prevent other CPUs from entering the critical section because it is ignored whenKDB_STATE_PRINTF_LOCKis set.The problematic situation might look like:
...
Signed-off-by Petr Mladek <[email protected]>---
kernel/debug/kdb/kdb_io.c| 36 +++++++++++++++++-------------------kernel/debug/kdb/kdb_private.h| 1 -2 files changed, 17 insertions(+), 20 deletions(-)kernel/debug/kdb/kdb_io.c +3
-3@@ -555,16 +555,16 @@ int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap)int colcount;int logging, saved_loglevel =0 ;int saved_trap_printk; -int got_printf_lock =0 ;int retlen =0 ;int fnd, len; +int this_cpu, old_cpu; +static int kdb_printf_cpu =-1 ;char *cp, *cp2, *cphold =NULL , replaced_byte =' ' ;char *moreprompt ="more> " ;struct console *c = console_drivers; -static DEFINE_SPINLOCK (kdb_printf_lock);unsigned long uninitialized_var (flags ); -preempt_disable (); +local_irq_save (flags); saved_trap_printk = kdb_trap_printk; kdb_trap_printk =0 ;@@ -572,13 +572,14 @@ int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap)* But if any cpu goes recursive in kdb, just print the output, * even if it is interleaved with any other text. kernel/debug/kdb/kdb_io.c int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap) · line 576
Quoted 10 lines
kernel/debug/kdb/kdb_io.c +2
-7*/ -if (!KDB_STATE (PRINTF_LOCK )) { -KDB_STATE_SET (PRINTF_LOCK ); -spin_lock_irqsave (&kdb_printf_lock, flags); - got_printf_lock =1 ; -atomic_inc (&kdb_event); - }else { -__acquire (kdb_printf_lock); + this_cpu =smp_processor_id (); +atomic_inc (&kdb_event);When reviewing I noticed that, when we recursively enter,
kdb_eventis handled differently after this patch so I wanted to figure out if this alternative handling ofkdb_eventwas safe.
Quoted 5 lines
In the end I concluded it is safe but that's mostly because the *only* thing we ever seem to do with
kdb_eventis increment and decrement it. So perhaps adding another patch at the front of this series to nuke this variable would be worthwhile (whilst making this patch easier to read).
Yeah, I was curious about kdb_event as well. I wondered if it might be used by some 3rd party stuff.
I can find only one usage. It was supposed to affect WARN_CONSOLE_UNLOCKED(), see
http://www.spinics.net/lists/kdb/msg01733.html
But this was never upstreamed, so kdb_event really looks like an historical artifact that might get removed. I am going to so in v2.
Quoted 2 lines
However, your choice and, either way:
Reviewed-by Daniel Thompson <[email protected]>
Thanks a lot for review.
Best Regards,
Petr
Petr Mladek
maintainerPATCH 2/2 kdb: Call vkdb_printf() from vprintk_default() only when wanted
In reply to Petr Mladekkdb_trap_printk allows to pass normal printk() messages to kdb via vkdb_printk(). For example, it is used to get backtrace using the classic show_stack(), see kdb_show_stack().
vkdb_printf() tries to avoid a potential infinite loop by disabling the trap. But this approach is racy, for example:
CPU1 CPU2
vkdb_printf()
// assume that kdb_trap_printk == 0
saved_trap_printk = kdb_trap_printk;
kdb_trap_printk = 0;
kdb_show_stack() kdb_trap_printk++;
Problem1: Now, a nested printk() on CPU0 calls vkdb_printf()
even when it should have been disabled. It will not cause a deadlock but...
// using the outdated saved value: 0
kdb_trap_printk = saved_trap_printk;
kdb_trap_printk--;
Problem2: Now, kdb_trap_printk == -1 and will stay like this.
It means that all messages will get passed to kdb from now on.
This patch removes the racy saved_trap_printk handling. Instead, the recursion is prevented by a check for the locked CPU.
--- include/linux/kdb.h | 1 + kernel/debug/kdb/kdb_io.c | 9 ++------- kernel/printk/printk.c | 4 +++- 3 files changed, 6 insertions(+), 8 deletions(-)
include/linux/kdb.h +1 -0
@@ -162,6 +162,7 @@ enum kdb_msgsrc { };extern int kdb_trap_printk; +extern int kdb_printf_cpu; extern __printf(2, 0) int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list args); extern __printf(1, 2) int kdb_printf(const char *, ...);
kernel/debug/kdb/kdb_io.c +2 -7
@@ -30,6 +30,7 @@char kdb_prompt_str[CMD_BUFLEN ];int kdb_trap_printk; +int kdb_printf_cpu =-1 ;static int kgdb_transition_check (char *buffer) {
@@ -554,24 +555,19 @@ int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap)int linecount;int colcount;int logging, saved_loglevel =0 ; -int saved_trap_printk;int retlen =0 ;int fnd, len;int this_cpu, old_cpu; -static int kdb_printf_cpu =-1 ;char *cp, *cp2, *cphold =NULL , replaced_byte =' ' ;char *moreprompt ="more> " ;struct console *c = console_drivers;unsigned long uninitialized_var (flags ); -local_irq_save (flags); - saved_trap_printk = kdb_trap_printk; - kdb_trap_printk =0 ; -/* Serialize kdb_printf if multiple cpus try to write at once. * But if any cpu goes recursive in kdb, just print the output, * even if it is interleaved with any other text. */ +local_irq_save (flags); this_cpu =smp_processor_id ();atomic_inc (&kdb_event);for (;;) {
@@ -853,7 +849,6 @@ int vkdb_printf(enum kdb_msgsrc src, const char *fmt, va_list ap)/* Update kdb_event around the locked section. */ smp_mb__before_atomic ();atomic_dec (&kdb_event); - kdb_trap_printk = saved_trap_printk;local_irq_restore (flags);return retlen; }
kernel/printk/printk.c +3 -1
@@ -1941,7 +1941,9 @@ int vprintk_default(const char *fmt, va_list args)int r;#ifdef CONFIG_KGDB_KDB -if (unlikely (kdb_trap_printk)) { +/* Allow to pass printk() to kdb but avoid a recursion. */ +if (unlikely (kdb_trap_printk && + kdb_printf_cpu !=smp_processor_id ())) { r =vkdb_printf (KDB_MSGSRC_PRINTK , fmt, args);return r; }
Signature · 1 line
1.8.5.6
Re: [PATCH 2/2] kdb: Call vkdb_printf() from vprintk_default() only when wanted
On (10/21/16 14:50), Petr Mladek wrote:
[..]
kernel/printk/printk.c int vprintk_default(const char *fmt, va_list args) · line 1946
Quoted 12 lines
kernel/printk/printk.c +3
-1@@ -1941,7 +1941,9 @@ int vprintk_default(const char *fmt, va_list args)int r;#ifdef CONFIG_KGDB_KDB -if (unlikely (kdb_trap_printk)) { +/* Allow to pass printk() to kdb but avoid a recursion. */ +if (unlikely (kdb_trap_printk && + kdb_printf_cpu !=smp_processor_id ())) {
^^^^^ aren't we are in preemptible here? -ss
Quoted 2 lines
kernel/printk/printk.c +0
-0r =vkdb_printf (KDB_MSGSRC_PRINTK , fmt, args);return r;
Petr Mladek
maintainerRe: [PATCH 2/2] kdb: Call vkdb_printf() from vprintk_default() only when wanted
Quoted 9 lines · Sergey Senozhatsky
On (10/21/16 14:50), Petr Mladek wrote:
[..]Quoted 7 lines
kernel/printk/printk.c +0
-0@@ -1941,7 +1941,9 @@ int vprintk_default(const char *fmt, va_list args)int r;
Quoted 7 lines
kernel/printk/printk.c int vprintk_default(const char *fmt, va_list args) · line 1946
Quoted 5 lines
kernel/printk/printk.c +3
-1#ifdef CONFIG_KGDB_KDB -if (unlikely (kdb_trap_printk)) { +/* Allow to pass printk() to kdb but avoid a recursion. */ +if (unlikely (kdb_trap_printk && + kdb_printf_cpu !=smp_processor_id ())) {^^^^^ aren't we are in preemptible here?
Yeah, I looked on this from one side only. "kdb_printf_cpu" is set with disabled IRQs. Therefore the preemption is disabled if we are in the recursion scenario. But you are right that we might get a false positive if we are preempted in the middle of this check and later scheduled on the CPU that called kdb_vprintf before.
Best Regards,
Petr
Re: [PATCH 2/2] kdb: Call vkdb_printf() from vprintk_default() only when wanted
In reply to Petr MladekQuoted 9 lines · Petr Mladek
kdb_trap_printkallows to pass normalprintk()messages to kdb viavkdb_printk(). For example, it is used to get backtrace using the classicshow_stack(), seekdb_show_stack().
vkdb_printf()tries to avoid a potential infinite loop by disabling the trap. But this approach is racy, for example:CPU1 CPU2
Quoted 7 lines
vkdb_printf()
// assume thatkdb_trap_printk== 0
saved_trap_printk=kdb_trap_printk;
kdb_trap_printk= 0;kdb_show_stack() kdb_trap_printk++;
When kdb is running any of the commands that use kdb_trap_printk there is a single active CPU and the other CPUs should be in a holding pen inside kgdb_cpu_enter().
The only time this is violated is when there is a timeout waiting for the other CPUs to report to the holding pen.
kernel/printk/printk.c int vprintk_default(const char *fmt, va_list args) · line 1946
Quoted 12 lines
kernel/printk/printk.c +3
-1@@ -1941,7 +1941,9 @@ int vprintk_default(const char *fmt, va_list args)int r;#ifdef CONFIG_KGDB_KDB -if (unlikely (kdb_trap_printk)) { +/* Allow to pass printk() to kdb but avoid a recursion. */ +if (unlikely (kdb_trap_printk && + kdb_printf_cpu !=smp_processor_id ())) {
Firstly, why !=?
Secondly, if kdb_trap_printk is set and the "wrong" CPU calls printk then we have an opportunity to trap a rouge processor in the holding pen meaning the test should probably be part of vkdb_printk() anyway.
Daniel.
Petr Mladek
maintainerRe: [PATCH 2/2] kdb: Call vkdb_printf() from vprintk_default() only when wanted
Quoted 18 lines · Daniel Thompson
Quoted 9 lines · Petr Mladek
kdb_trap_printkallows to pass normalprintk()messages to kdb viavkdb_printk(). For example, it is used to get backtrace using the classicshow_stack(), seekdb_show_stack().
vkdb_printf()tries to avoid a potential infinite loop by disabling the trap. But this approach is racy, for example:CPU1 CPU2
Quoted 7 lines
vkdb_printf()
// assume thatkdb_trap_printk== 0
saved_trap_printk=kdb_trap_printk;
kdb_trap_printk= 0;kdb_show_stack() kdb_trap_printk++;
Quoted 6 lines
When kdb is running any of the commands that use
kdb_trap_printkthere is a single active CPU and the other CPUs should be in a holding pen insidekgdb_cpu_enter().The only time this is violated is when there is a timeout waiting for the other CPUs to report to the holding pen.
It means that the race window is small but it is there. Do I get it correctly, please?
Thanks a lot for explanation. I was not sure how exactly this worked. I only saw the games with kdb_printf_cpu in vkdb_printf(). Therefore I expected that some parallelism was possible.
Quoted 16 lines
kernel/printk/printk.c int vprintk_default(const char *fmt, va_list args) · line 1946
Quoted 13 lines
kernel/printk/printk.c +3
-1@@ -1941,7 +1941,9 @@ int vprintk_default(const char *fmt, va_list args)int r;#ifdef CONFIG_KGDB_KDB -if (unlikely (kdb_trap_printk)) { +/* Allow to pass printk() to kdb but avoid a recursion. */ +if (unlikely (kdb_trap_printk && + kdb_printf_cpu !=smp_processor_id ())) {Firstly, why !=?
Quoted 4 lines
Secondly, if
kdb_trap_printkis set and the "wrong" CPU calls printk then we have an opportunity to trap a rouge processor in the holding pen meaning the test should probably be part ofvkdb_printk()anyway.
I agree that it is confusing:
On one hand, vkdb_printf() explicitly allows recursion on the same CPU. See the handling of kdb_printf_lock before the 1st patch from this series. Also it mentioned by the comment:
/* Serialize kdb_printf if multiple cpus try to write at once. * But if any cpu goes recursive in kdb, just print the output, * even if it is interleaved with any other text. */
On the other hand. The lines
saved_trap_printk = kdb_trap_printk;
kdb_trap_printk = 0;means that someone wanted to explicitly disable recursion via the generic printk(). This is the reason why I used "!=" and why I added this check into vprintk_default().
By other words, we allow recursion caused by kdb internal messages that are printed directly by kdb_printf()). But we disable recursion caused by all other messages that are printed using the generic printk(). This patch keeps the logic. It might make some sense. But it is hard for me to judge.
Best Regards,
Petr
Re: [PATCH 2/2] kdb: Call vkdb_printf() from vprintk_default() only when wanted
Quoted 23 lines · Petr Mladek
Quoted 22 lines · Daniel Thompson
Quoted 9 lines · Petr Mladek
kdb_trap_printkallows to pass normalprintk()messages to kdb viavkdb_printk(). For example, it is used to get backtrace using the classicshow_stack(), seekdb_show_stack().
vkdb_printf()tries to avoid a potential infinite loop by disabling the trap. But this approach is racy, for example:CPU1 CPU2
Quoted 7 lines
vkdb_printf()
// assume thatkdb_trap_printk== 0
saved_trap_printk=kdb_trap_printk;
kdb_trap_printk= 0;kdb_show_stack() kdb_trap_printk++;When kdb is running any of the commands that use
kdb_trap_printkthere is a single active CPU and the other CPUs should be in a holding pen insidekgdb_cpu_enter().
Quoted 5 lines
Quoted 2 lines
The only time this is violated is when there is a timeout waiting for the other CPUs to report to the holding pen.
It means that the race window is small but it is there. Do I get it correctly, please?
I don't think the size of the race window is particularly interesting; it does exist.
It is more important to be clear that the circumstances when the race exists are when an attempt to stop-the-world has failed. So rather than close the race it might be more useful to make the race unreachable by bringing the CPU that has failed to report under control.
Quoted 3 lines
Thanks a lot for explanation. I was not sure how exactly this worked. I only saw the games with
kdb_printf_cpuinvkdb_printf(). Therefore I expected that some parallelism was possible.
Yes. I'm coming round to the point-of-view that if the code looks like it expected to run in parallel if should be correct for it to run in parallel! Otherwise its leads to broken thinking when changing things.
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
kernel/printk/printk.c +0
-0@@ -1941,7 +1941,9 @@ int vprintk_default(const char *fmt, va_list args)int r;
Quoted 7 lines
Quoted 7 lines
kernel/printk/printk.c int vprintk_default(const char *fmt, va_list args) · line 1946
Quoted 5 lines
kernel/printk/printk.c +3
-1#ifdef CONFIG_KGDB_KDB -if (unlikely (kdb_trap_printk)) { +/* Allow to pass printk() to kdb but avoid a recursion. */ +if (unlikely (kdb_trap_printk && + kdb_printf_cpu !=smp_processor_id ())) {Firstly, why !=?
Having re-read things, this comment was spurious.
Quoted 16 lines
Quoted 4 lines
Secondly, if
kdb_trap_printkis set and the "wrong" CPU calls printk then we have an opportunity to trap a rouge processor in the holding pen meaning the test should probably be part ofvkdb_printk()anyway.I agree that it is confusing:
On one hand,
vkdb_printf()explicitly allows recursion on the same CPU. See the handling ofkdb_printf_lockbefore the 1st patch from this series. Also it mentioned by the comment:/* Serialize kdb_printf if multiple cpus try to write at once. * But if any cpu goes recursive in kdb, just print the output, * even if it is interleaved with any other text. */
Quoted 8 lines
On the other hand. The lines
saved_trap_printk = kdb_trap_printk; kdb_trap_printk = 0;means that someone wanted to explicitly disable recursion via the generic
printk(). This is the reason why I used "!=" and why I added this check intovprintk_default().
vkdb_printf()'s rough job is to:
1. Issue the string to the kdb console (not the same as kernel console)
2. Store the string in the kernel logs.
Of the above, #2 is achieved by temporarily setting the console log level to 0, calling printk() and restoring the log level. This is why vkdb_printf() needs the silly dance to avoid the recursion.
Quoted 5 lines
By other words, we allow recursion caused by kdb internal messages that are printed directly by
kdb_printf(). But we disable recursion caused by all other messages that are printed using the genericprintk(). This patch keeps the logic. It might make some sense. But it is hard for me to judge.
Yes, I think it makes sense.
Right now I'm toying with the idea of using the printk_func code for printk() interception.
Firstly printk_func is per-cpu which removes a huge chain of complex reasoning (for a case that doesn't really exist).
Secondly we could call the saved_printk_func directly making recursion impossible.
Sadly, if we accept that a rouge CPU might still be calling printk() then the approach above just opens up a race on the console log level...
Sigh...
Daniel.
Quoted 3 lines
Best Regards,
Petr
Petr Mladek
maintainerRe: [PATCH 2/2] kdb: Call vkdb_printf() from vprintk_default() only when wanted
Quoted 30 lines · Daniel Thompson
Quoted 23 lines · Petr Mladek
Quoted 22 lines · Daniel Thompson
Quoted 9 lines · Petr Mladek
kdb_trap_printkallows to pass normalprintk()messages to kdb viavkdb_printk(). For example, it is used to get backtrace using the classicshow_stack(), seekdb_show_stack().
vkdb_printf()tries to avoid a potential infinite loop by disabling the trap. But this approach is racy, for example:CPU1 CPU2
Quoted 7 lines
vkdb_printf()
// assume thatkdb_trap_printk== 0saved_trap_printk=kdb_trap_printk;kdb_trap_printk= 0;kdb_show_stack() kdb_trap_printk++;When kdb is running any of the commands that use
kdb_trap_printkthere is a single active CPU and the other CPUs should be in a holding pen insidekgdb_cpu_enter().Quoted 5 lines
Quoted 2 lines
The only time this is violated is when there is a timeout waiting for the other CPUs to report to the holding pen.
It means that the race window is small but it is there. Do I get it correctly, please?
Quoted 8 lines
I don't think the size of the race window is particularly interesting; it does exist.
It is more important to be clear that the circumstances when the race exists are when an attempt to stop-the-world has failed. So rather than close the race it might be more useful to make the race unreachable by bringing the CPU that has failed to report under control.
Yup. The question is how the stop-the-world could fail and if we could prevent all failures now and in the future.
Quoted 10 lines
vkdb_printf()'s rough job is to:
1. Issue the string to the kdb console (not the same as kernel console)
2. Store the string in the kernel logs.Of the above, #2 is achieved by temporarily setting the console log level to 0, calling
printk()and restoring the log level. This is whyvkdb_printf()needs the silly dance to avoid the recursion.
Quoted 8 lines
Right now I'm toying with the idea of using the
printk_funccode forprintk()interception.Firstly
printk_funcis per-cpu which removes a huge chain of complex reasoning (for a case that doesn't really exist).Secondly we could call the
saved_printk_funcdirectly making recursion impossible.
Note that there are plans to define per-CPU printk_context variable, see https://lkml.kernel.org/r/[email protected]
It will be used to choose the right printk_func. It will allow
to have more contexts and enter some of them recursively.
Then it should be easier to add support for KDB context.
Quoted 3 lines
Sadly, if we accept that a rouge CPU might still be calling
printk()then the approach above just opens up a race on the console log level...
We are also very close to add async printk. It will allow to delegate the console handling into separate kthread. Then printk() should not longer call console directly. The only exception would be a system panic, when we really want to get messages out ASAP.
This last patchset can be seen at
https://lkml.kernel.org/r/[email protected]
But Sergey plans to get in the printk_context/printk_safe stuff first.
Anyway, then it should be easier to disable the console in kdb context.
Best Regards,
Petr
PS: I am going to prepare v2 of this patchset. It might take some time as I am repeatedly interrupted by some other urgent work.