Skip to contentSkip to conversation

Direct firmware load failed with error 2

DISCUSSION [email protected] 3 participants 12 messages Oct 24, 2016 – Oct 27, 2016 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore
#0 lore raw

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more. I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[ 7.172118] ath10k: pci irq MSI 
[ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper 
[ 8.626488] ath10k: could not fetch board data (-2) 
[ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper 
[ 8.712302] ath10k: could not fetch board data (-2) 
[ 8.722757] ath10k: could not fetch firmware files (-2) 
[ 8.781868] ath10k: could not probe fw (-2) 
[ 8.781874] ath10k: failed to register driver core: -2 
[ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#1 lore raw

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 30 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more. I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[ 7.172118] ath10k: pci irq MSI
[ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.626488] ath10k: could not fetch board data (-2)
[ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.712302] ath10k: could not fetch board data (-2)
[ 8.722757] ath10k: could not fetch firmware files (-2)
[ 8.781868] ath10k: could not probe fw (-2)
[ 8.781874] ath10k: failed to register driver core: -2
[ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#2 lore raw

Thanks Ben,

Got the location from the website:

root@apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls                         
firmware-2.bin         firmware-5.bin  

I'll figure out how to do some printk's (I'm a newbie).

Thanks,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 4:11pm
To: [email protected], [email protected]
Subject: Re: Direct firmware load failed with error 2

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 30 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more. I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[ 7.172118] ath10k: pci irq MSI
[ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.626488] ath10k: could not fetch board data (-2)
[ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.712302] ath10k: could not fetch board data (-2)
[ 8.722757] ath10k: could not fetch firmware files (-2)
[ 8.781868] ath10k: could not probe fw (-2)
[ 8.781874] ath10k: failed to register driver core: -2
[ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 15 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k



_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#3 lore raw

You need board.bin too. Something like this if you want to use my firmware, or firmware-5.bin for upstream 10.2 firmware:

[root@ben-ota-1 lanforge]# ls -l /lib/firmware/ath10k/QCA988X/hw2.0/ total 1084
-rw-r--r--. 1 root root 2116 Sep 27 14:43 board.bin
-rw-r--r--. 1 root root 201324 Oct 13 18:48 firmware-2.bin

Thanks,
Ben

Quoted 61 lines · On 10/24/2016 01:59 PM, [email protected] wrote:

Thanks Ben,

Got the location from the website:

root@apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls
firmware-2.bin         firmware-5.bin

I'll figure out how to do some printk's (I'm a newbie).

Thanks,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 4:11pm
To: [email protected], [email protected]
Subject: Re: Direct firmware load failed with error 2

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 30 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more. I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[ 7.172118] ath10k: pci irq MSI
[ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.626488] ath10k: could not fetch board data (-2)
[ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.712302] ath10k: could not fetch board data (-2)
[ 8.722757] ath10k: could not fetch firmware files (-2)
[ 8.781868] ath10k: could not probe fw (-2)
[ 8.781874] ath10k: failed to register driver core: -2
[ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#4 lore raw

Great, thanks Ben,

That cleared up the firmware load error but I now have:

[    6.997553] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[    7.075559] ath10k: pci irq MSI                                              
[    9.753487] ath10k: ctl_resp never came in (-110)                            
[    9.758281] ath10k: failed to connect to HTC: -110                           
[    9.803633] ath10k: could not init core (-110)                               
[    9.843495] ath10k: could not probe fw (-110)                                
[    9.843499] ath10k: failed to register driver core: -110                     
[    9.843681] ath10k_pci: probe of 0000:01:00.0 failed with error -110 

Any ideas? Let me know if I should post this new.

Thanks a bunch
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 5:05pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

You need board.bin too. Something like this if you want to use my firmware, or firmware-5.bin for upstream 10.2 firmware:

[root@ben-ota-1 lanforge]# ls -l /lib/firmware/ath10k/QCA988X/hw2.0/ total 1084
-rw-r--r--. 1 root root 2116 Sep 27 14:43 board.bin
-rw-r--r--. 1 root root 201324 Oct 13 18:48 firmware-2.bin

Thanks,
Ben

Quoted 61 lines · On 10/24/2016 01:59 PM, [email protected] wrote:

Thanks Ben,

Got the location from the website:

root@apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls
firmware-2.bin         firmware-5.bin

I'll figure out how to do some printk's (I'm a newbie).

Thanks,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 4:11pm
To: [email protected], [email protected]
Subject: Re: Direct firmware load failed with error 2

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 30 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more. I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[ 7.172118] ath10k: pci irq MSI
[ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.626488] ath10k: could not fetch board data (-2)
[ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.712302] ath10k: could not fetch board data (-2)
[ 8.722757] ath10k: could not fetch firmware files (-2)
[ 8.781868] ath10k: could not probe fw (-2)
[ 8.781874] ath10k: failed to register driver core: -2
[ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 15 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k



_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#5 lore raw

Please let us know 'lspci' or equiv, exactly what firmware you are loading, kernel driver version, etc.

Maybe try LEDE if you can, it's likely more up to date.

Thanks,
Ben

Quoted 102 lines · On 10/24/2016 04:22 PM, [email protected] wrote:

Great, thanks Ben,

That cleared up the firmware load error but I now have:

[    6.997553] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[    7.075559] ath10k: pci irq MSI
[    9.753487] ath10k: ctl_resp never came in (-110)
[    9.758281] ath10k: failed to connect to HTC: -110
[    9.803633] ath10k: could not init core (-110)
[    9.843495] ath10k: could not probe fw (-110)
[    9.843499] ath10k: failed to register driver core: -110
[    9.843681] ath10k_pci: probe of 0000:01:00.0 failed with error -110

Any ideas? Let me know if I should post this new.

Thanks a bunch
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 5:05pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

You need board.bin too. Something like this if you want to use my firmware, or firmware-5.bin for upstream 10.2 firmware:

[root@ben-ota-1 lanforge]# ls -l /lib/firmware/ath10k/QCA988X/hw2.0/ total 1084

(quoted diff) +0 -2
-rw-r--r--. 1 root root   2116 Sep 27 14:43 board.bin
-rw-r--r--. 1 root root 201324 Oct 13 18:48 firmware-2.bin

Thanks,
Ben

Quoted 61 lines · On 10/24/2016 01:59 PM, [email protected] wrote:

Thanks Ben,

Got the location from the website:

root@apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls
firmware-2.bin         firmware-5.bin

I'll figure out how to do some printk's (I'm a newbie).

Thanks,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 4:11pm
To: [email protected], [email protected]
Subject: Re: Direct firmware load failed with error 2

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 30 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more. I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[ 7.172118] ath10k: pci irq MSI
[ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.626488] ath10k: could not fetch board data (-2)
[ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.712302] ath10k: could not fetch board data (-2)
[ 8.722757] ath10k: could not fetch firmware files (-2)
[ 8.781868] ath10k: could not probe fw (-2)
[ 8.781874] ath10k: failed to register driver core: -2
[ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 7 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#6 lore raw

Hi Ben

root@apalis-imx6:~# lspci -v                                                                                    
00:00.0 PCI bridge: Synopsys, Inc. Device abcd (rev 01) (prog-if 00 [Normal decode])                            
        Flags: bus master, fast devsel, latency 0, IRQ 388                                                      
        Memory at 01200000 (32-bit, non-prefetchable) [size=1M]                                                 
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0                                            
        Memory behind bridge: 01000000-011fffff                                                                 
        Prefetchable memory behind bridge: 01300000-013fffff                                                    
        [virtual] Expansion ROM at 01400000 [disabled] [size=64K]                                               
        Capabilities: [40] Power Management version 3                                                           
        Capabilities: [50] MSI: Enable+ Count=1/1 Maskable+ 64bit+                                              
        Capabilities: [70] Express Root Port (Slot-), MSI 00                                                    
        Capabilities: [100] Advanced Error Reporting                                                            
        Capabilities: [140] Virtual Channel                                                                     
        Kernel driver in use: pcieport                                                                          

01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
Flags: fast devsel, IRQ 155
Memory at 01000000 (64-bit, non-prefetchable) [size=2M]
[virtual] Expansion ROM at 01300000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=8/8 Maskable+ 64bit-
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00 Kernel modules: ath10k_pci
----------

Angstrom v2015.12 - Kernel 3.14.52-v2.6b2+g7c83cef

Apalis_iMX6_LinuxImageV2.6_20160929

This is Toradex's standard build for their Apalis iMX6 on a Ixora carrier. I think they are due for a new major release very soon. I can check if you think it's worth it.

The current firmware is yours (firmware-2-ct-full-community.bin), fresh off your site today. I downloaded board.bin today too.
---------------

root@apalis-imx6:~# lsmod                                                                                       
Module                  Size  Used by                                                                           
usb_f_rndis            11441  2                                                                                 
u_ether                 9135  1 usb_f_rndis                                                                     
usb_f_acm               4105  2                                                                                 
u_serial                8487  1 usb_f_acm                                                                       
ov5640_camera_mipi_int    21588  0                                                                              
mxc_v4l2_capture       24990  1 ov5640_camera_mipi_int                                                          
ipu_bg_overlay_sdc      4113  1 mxc_v4l2_capture                                                                
ipu_still               1631  1 mxc_v4l2_capture                                                                
ipu_prp_enc             4653  1 mxc_v4l2_capture                                                                
max9526_tvin            5800  0                                                                                 
ipu_csi_enc             2917  1 mxc_v4l2_capture                                                                
ipu_fg_overlay_sdc      4978  1 mxc_v4l2_capture                                                                
adv7280_tvin            6563  0                                                                                 
v4l2_int_device         1759  4 adv7280_tvin,ov5640_camera_mipi_int,mxc_v4l2_capture,max9526_tvin               
ath10k_pci             27397  0                                                                                 
ath10k_core           101131  1 ath10k_pci                                                                      
ath                    17381  1 ath10k_core                                                                     
mac80211              254675  1 ath10k_core                                                                     
cfg80211              166770  3 ath,mac80211,ath10k_core                                                        
libcomposite           28353  12 usb_f_acm,usb_f_rndis                                                          
configfs               20737  4 usb_f_acm,usb_f_rndis,libcomposite                                              
galcore               207484  2    

------------

root@apalis-imx6:~# ip link                                                                                     
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default                  
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00                                                       
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10                           
    link/can                                                                                                    
3: can1: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10                           
    link/can                                                                                                    
4: eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group defaul0
    link/ether 00:14:2d:4a:30:f9 brd ff:ff:ff:ff:ff:ff                                                          
5: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default                                 
    link/sit 0.0.0.0 brd 0.0.0.0                                                                                
6: usb0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default ql0
    link/ether 00:14:2d:ff:ff:ff brd ff:ff:ff:ff:ff:ff 

Thanks again,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 9:57pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Please let us know 'lspci' or equiv, exactly what firmware you are loading, kernel driver version, etc.

Maybe try LEDE if you can, it's likely more up to date.

Thanks,
Ben

Quoted 102 lines · On 10/24/2016 04:22 PM, [email protected] wrote:

Great, thanks Ben,

That cleared up the firmware load error but I now have:

[    6.997553] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[    7.075559] ath10k: pci irq MSI
[    9.753487] ath10k: ctl_resp never came in (-110)
[    9.758281] ath10k: failed to connect to HTC: -110
[    9.803633] ath10k: could not init core (-110)
[    9.843495] ath10k: could not probe fw (-110)
[    9.843499] ath10k: failed to register driver core: -110
[    9.843681] ath10k_pci: probe of 0000:01:00.0 failed with error -110

Any ideas? Let me know if I should post this new.

Thanks a bunch
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 5:05pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

You need board.bin too. Something like this if you want to use my firmware, or firmware-5.bin for upstream 10.2 firmware:

[root@ben-ota-1 lanforge]# ls -l /lib/firmware/ath10k/QCA988X/hw2.0/ total 1084

(quoted diff) +0 -2
-rw-r--r--. 1 root root   2116 Sep 27 14:43 board.bin
-rw-r--r--. 1 root root 201324 Oct 13 18:48 firmware-2.bin

Thanks,
Ben

Quoted 61 lines · On 10/24/2016 01:59 PM, [email protected] wrote:

Thanks Ben,

Got the location from the website:

root@apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls
firmware-2.bin         firmware-5.bin

I'll figure out how to do some printk's (I'm a newbie).

Thanks,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 4:11pm
To: [email protected], [email protected]
Subject: Re: Direct firmware load failed with error 2

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 30 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more. I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[ 7.172118] ath10k: pci irq MSI
[ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.626488] ath10k: could not fetch board data (-2)
[ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.712302] ath10k: could not fetch board data (-2)
[ 8.722757] ath10k: could not fetch firmware files (-2)
[ 8.781868] ath10k: could not probe fw (-2)
[ 8.781874] ath10k: failed to register driver core: -2
[ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 14 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k



_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#7 lore raw

Hi Ben,

Forgot to mention. Our hardware is not supported by OpenWRT, so going to LEDE at this point may be too tough. I'm an RF guy, so this is a steep hill.

Colin

-----Original Message-----
From: [email protected]
Sent: Monday, October 24, 2016 10:59pm
To: "Ben Greear" <[email protected]>
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Hi Ben

root@apalis-imx6:~# lspci -v                                                                                    
00:00.0 PCI bridge: Synopsys, Inc. Device abcd (rev 01) (prog-if 00 [Normal decode])                            
        Flags: bus master, fast devsel, latency 0, IRQ 388                                                      
        Memory at 01200000 (32-bit, non-prefetchable) [size=1M]                                                 
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0                                            
        Memory behind bridge: 01000000-011fffff                                                                 
        Prefetchable memory behind bridge: 01300000-013fffff                                                    
        [virtual] Expansion ROM at 01400000 [disabled] [size=64K]                                               
        Capabilities: [40] Power Management version 3                                                           
        Capabilities: [50] MSI: Enable+ Count=1/1 Maskable+ 64bit+                                              
        Capabilities: [70] Express Root Port (Slot-), MSI 00                                                    
        Capabilities: [100] Advanced Error Reporting                                                            
        Capabilities: [140] Virtual Channel                                                                     
        Kernel driver in use: pcieport                                                                          

01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
Flags: fast devsel, IRQ 155
Memory at 01000000 (64-bit, non-prefetchable) [size=2M]
[virtual] Expansion ROM at 01300000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=8/8 Maskable+ 64bit-
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00 Kernel modules: ath10k_pci
----------

Angstrom v2015.12 - Kernel 3.14.52-v2.6b2+g7c83cef

Apalis_iMX6_LinuxImageV2.6_20160929

This is Toradex's standard build for their Apalis iMX6 on a Ixora carrier. I think they are due for a new major release very soon. I can check if you think it's worth it.

The current firmware is yours (firmware-2-ct-full-community.bin), fresh off your site today. I downloaded board.bin today too.
---------------

root@apalis-imx6:~# lsmod                                                                                       
Module                  Size  Used by                                                                           
usb_f_rndis            11441  2                                                                                 
u_ether                 9135  1 usb_f_rndis                                                                     
usb_f_acm               4105  2                                                                                 
u_serial                8487  1 usb_f_acm                                                                       
ov5640_camera_mipi_int    21588  0                                                                              
mxc_v4l2_capture       24990  1 ov5640_camera_mipi_int                                                          
ipu_bg_overlay_sdc      4113  1 mxc_v4l2_capture                                                                
ipu_still               1631  1 mxc_v4l2_capture                                                                
ipu_prp_enc             4653  1 mxc_v4l2_capture                                                                
max9526_tvin            5800  0                                                                                 
ipu_csi_enc             2917  1 mxc_v4l2_capture                                                                
ipu_fg_overlay_sdc      4978  1 mxc_v4l2_capture                                                                
adv7280_tvin            6563  0                                                                                 
v4l2_int_device         1759  4 adv7280_tvin,ov5640_camera_mipi_int,mxc_v4l2_capture,max9526_tvin               
ath10k_pci             27397  0                                                                                 
ath10k_core           101131  1 ath10k_pci                                                                      
ath                    17381  1 ath10k_core                                                                     
mac80211              254675  1 ath10k_core                                                                     
cfg80211              166770  3 ath,mac80211,ath10k_core                                                        
libcomposite           28353  12 usb_f_acm,usb_f_rndis                                                          
configfs               20737  4 usb_f_acm,usb_f_rndis,libcomposite                                              
galcore               207484  2    

------------

root@apalis-imx6:~# ip link                                                                                     
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default                  
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00                                                       
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10                           
    link/can                                                                                                    
3: can1: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10                           
    link/can                                                                                                    
4: eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group defaul0
    link/ether 00:14:2d:4a:30:f9 brd ff:ff:ff:ff:ff:ff                                                          
5: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default                                 
    link/sit 0.0.0.0 brd 0.0.0.0                                                                                
6: usb0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default ql0
    link/ether 00:14:2d:ff:ff:ff brd ff:ff:ff:ff:ff:ff 

Thanks again,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 9:57pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Please let us know 'lspci' or equiv, exactly what firmware you are loading, kernel driver version, etc.

Maybe try LEDE if you can, it's likely more up to date.

Thanks,
Ben

Quoted 102 lines · On 10/24/2016 04:22 PM, [email protected] wrote:

Great, thanks Ben,

That cleared up the firmware load error but I now have:

[    6.997553] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[    7.075559] ath10k: pci irq MSI
[    9.753487] ath10k: ctl_resp never came in (-110)
[    9.758281] ath10k: failed to connect to HTC: -110
[    9.803633] ath10k: could not init core (-110)
[    9.843495] ath10k: could not probe fw (-110)
[    9.843499] ath10k: failed to register driver core: -110
[    9.843681] ath10k_pci: probe of 0000:01:00.0 failed with error -110

Any ideas? Let me know if I should post this new.

Thanks a bunch
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 5:05pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

You need board.bin too. Something like this if you want to use my firmware, or firmware-5.bin for upstream 10.2 firmware:

[root@ben-ota-1 lanforge]# ls -l /lib/firmware/ath10k/QCA988X/hw2.0/ total 1084

(quoted diff) +0 -2
-rw-r--r--. 1 root root   2116 Sep 27 14:43 board.bin
-rw-r--r--. 1 root root 201324 Oct 13 18:48 firmware-2.bin

Thanks,
Ben

Quoted 61 lines · On 10/24/2016 01:59 PM, [email protected] wrote:

Thanks Ben,

Got the location from the website:

root@apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls
firmware-2.bin         firmware-5.bin

I'll figure out how to do some printk's (I'm a newbie).

Thanks,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 4:11pm
To: [email protected], [email protected]
Subject: Re: Direct firmware load failed with error 2

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 30 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more. I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[ 7.172118] ath10k: pci irq MSI
[ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.626488] ath10k: could not fetch board data (-2)
[ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.712302] ath10k: could not fetch board data (-2)
[ 8.722757] ath10k: could not fetch firmware files (-2)
[ 8.781868] ath10k: could not probe fw (-2)
[ 8.781874] ath10k: failed to register driver core: -2
[ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 21 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k



_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k



_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#8 lore raw

Your kernel is so old that it will likely be a pain to get things working.

You can do backports, and I have manually done some backporting for users with similarly old kernels (using my 3.17 tree is a upstream kernel), but it is not something I do for fun.

If for some reason stock firmware-2.bin works and mine does not, then let me know and maybe I can help.

Thanks,
Ben

Quoted 214 lines · On 10/24/2016 08:11 PM, [email protected] wrote:

Hi Ben,

Forgot to mention. Our hardware is not supported by OpenWRT, so going to LEDE at this point may be too tough. I'm an RF guy, so this is a steep hill.

Colin

-----Original Message-----
From: [email protected]
Sent: Monday, October 24, 2016 10:59pm
To: "Ben Greear" <[email protected]>
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Hi Ben

root@apalis-imx6:~# lspci -v
00:00.0 PCI bridge: Synopsys, Inc. Device abcd (rev 01) (prog-if 00 [Normal decode])
         Flags: bus master, fast devsel, latency 0, IRQ 388
         Memory at 01200000 (32-bit, non-prefetchable) [size=1M]
         Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
         Memory behind bridge: 01000000-011fffff
         Prefetchable memory behind bridge: 01300000-013fffff
         [virtual] Expansion ROM at 01400000 [disabled] [size=64K]
         Capabilities: [40] Power Management version 3
         Capabilities: [50] MSI: Enable+ Count=1/1 Maskable+ 64bit+
         Capabilities: [70] Express Root Port (Slot-), MSI 00
         Capabilities: [100] Advanced Error Reporting
         Capabilities: [140] Virtual Channel
         Kernel driver in use: pcieport

01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
Flags: fast devsel, IRQ 155
Memory at 01000000 (64-bit, non-prefetchable) [size=2M]
[virtual] Expansion ROM at 01300000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=8/8 Maskable+ 64bit-
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00 Kernel modules: ath10k_pci
----------

Angstrom v2015.12 - Kernel 3.14.52-v2.6b2+g7c83cef

Apalis_iMX6_LinuxImageV2.6_20160929

This is Toradex's standard build for their Apalis iMX6 on a Ixora carrier. I think they are due for a new major release very soon. I can check if you think it's worth it.

The current firmware is yours (firmware-2-ct-full-community.bin), fresh off your site today. I downloaded board.bin today too.
---------------

root@apalis-imx6:~# lsmod
Module                  Size  Used by
usb_f_rndis            11441  2
u_ether                 9135  1 usb_f_rndis
usb_f_acm               4105  2
u_serial                8487  1 usb_f_acm
ov5640_camera_mipi_int    21588  0
mxc_v4l2_capture       24990  1 ov5640_camera_mipi_int
ipu_bg_overlay_sdc      4113  1 mxc_v4l2_capture
ipu_still               1631  1 mxc_v4l2_capture
ipu_prp_enc             4653  1 mxc_v4l2_capture
max9526_tvin            5800  0
ipu_csi_enc             2917  1 mxc_v4l2_capture
ipu_fg_overlay_sdc      4978  1 mxc_v4l2_capture
adv7280_tvin            6563  0
v4l2_int_device         1759  4 adv7280_tvin,ov5640_camera_mipi_int,mxc_v4l2_capture,max9526_tvin
ath10k_pci             27397  0
ath10k_core           101131  1 ath10k_pci
ath                    17381  1 ath10k_core
mac80211              254675  1 ath10k_core
cfg80211              166770  3 ath,mac80211,ath10k_core
libcomposite           28353  12 usb_f_acm,usb_f_rndis
configfs               20737  4 usb_f_acm,usb_f_rndis,libcomposite
galcore               207484  2

------------

root@apalis-imx6:~# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
     link/can
3: can1: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
     link/can
4: eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group defaul0
     link/ether 00:14:2d:4a:30:f9 brd ff:ff:ff:ff:ff:ff
5: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
     link/sit 0.0.0.0 brd 0.0.0.0
6: usb0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default ql0
     link/ether 00:14:2d:ff:ff:ff brd ff:ff:ff:ff:ff:ff

Thanks again,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 9:57pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Please let us know 'lspci' or equiv, exactly what firmware you are loading, kernel driver version, etc.

Maybe try LEDE if you can, it's likely more up to date.

Thanks,
Ben

Quoted 102 lines · On 10/24/2016 04:22 PM, [email protected] wrote:

Great, thanks Ben,

That cleared up the firmware load error but I now have:

[    6.997553] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[    7.075559] ath10k: pci irq MSI
[    9.753487] ath10k: ctl_resp never came in (-110)
[    9.758281] ath10k: failed to connect to HTC: -110
[    9.803633] ath10k: could not init core (-110)
[    9.843495] ath10k: could not probe fw (-110)
[    9.843499] ath10k: failed to register driver core: -110
[    9.843681] ath10k_pci: probe of 0000:01:00.0 failed with error -110

Any ideas? Let me know if I should post this new.

Thanks a bunch
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 5:05pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

You need board.bin too. Something like this if you want to use my firmware, or firmware-5.bin for upstream 10.2 firmware:

[root@ben-ota-1 lanforge]# ls -l /lib/firmware/ath10k/QCA988X/hw2.0/ total 1084

(quoted diff) +0 -2
-rw-r--r--. 1 root root   2116 Sep 27 14:43 board.bin
-rw-r--r--. 1 root root 201324 Oct 13 18:48 firmware-2.bin

Thanks,
Ben

Quoted 61 lines · On 10/24/2016 01:59 PM, [email protected] wrote:

Thanks Ben,

Got the location from the website:

root@apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls
firmware-2.bin         firmware-5.bin

I'll figure out how to do some printk's (I'm a newbie).

Thanks,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 4:11pm
To: [email protected], [email protected]
Subject: Re: Direct firmware load failed with error 2

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 30 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more. I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
[ 7.172118] ath10k: pci irq MSI
[ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.626488] ath10k: could not fetch board data (-2)
[ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.712302] ath10k: could not fetch board data (-2)
[ 8.722757] ath10k: could not fetch firmware files (-2)
[ 8.781868] ath10k: could not probe fw (-2)
[ 8.781874] ath10k: failed to register driver core: -2
[ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 7 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#9 lore raw

Hi Colin,

As Ben wrote: you need backports.
You can look at gateworks github for examples how it can be done in yocto. They have recipes for ath10k firmware and backports (compat-wireless):

Ath10k firmware :
https://github.com/Gateworks/meta-gateworks/tree/fido/recipes-connectivity/ath10k-firmware

and backports
https://github.com/Gateworks/meta-gateworks/tree/fido/recipes-kernel/compat-wireless

Of course it is not as simple as just adding those recipes, but it is good point to start.

If you need newer ath10k firmware then is is quite easy to update ath10k-firmware recipe.
With compat-wireless it is not so easy but it is possible.

Marek

Quoted 258 lines · Ben Greear

Your kernel is so old that it will likely be a pain to get things working.

You can do backports, and I have manually done some backporting for users with similarly old kernels (using my 3.17 tree is a upstream kernel), but it is not something I do for fun.

If for some reason stock firmware-2.bin works and mine does not, then let me know and maybe I can help.

Thanks,
Ben

Quoted 120 lines · On 10/24/2016 08:11 PM, [email protected] wrote:

Hi Ben,

Forgot to mention. Our hardware is not supported by OpenWRT, so going to LEDE at this point may be too tough. I'm an RF guy, so this is a steep hill.

Colin

-----Original Message-----
From: [email protected]
Sent: Monday, October 24, 2016 10:59pm
To: "Ben Greear" <[email protected]>
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Hi Ben

root@apalis-imx6:~# lspci -v
00:00.0 PCI bridge: Synopsys, Inc. Device abcd (rev 01) (prog-if 00
[Normal decode])
         Flags: bus master, fast devsel, latency 0, IRQ 388
         Memory at 01200000 (32-bit, non-prefetchable) [size=1M]
         Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
         Memory behind bridge: 01000000-011fffff
         Prefetchable memory behind bridge: 01300000-013fffff
         [virtual] Expansion ROM at 01400000 [disabled] [size=64K]
         Capabilities: [40] Power Management version 3
         Capabilities: [50] MSI: Enable+ Count=1/1 Maskable+ 64bit+
         Capabilities: [70] Express Root Port (Slot-), MSI 00
         Capabilities: [100] Advanced Error Reporting
         Capabilities: [140] Virtual Channel
         Kernel driver in use: pcieport

01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
Flags: fast devsel, IRQ 155
Memory at 01000000 (64-bit, non-prefetchable) [size=2M] [virtual] Expansion ROM at 01300000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=8/8 Maskable+ 64bit-
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00 Kernel modules: ath10k_pci
----------

Angstrom v2015.12 - Kernel 3.14.52-v2.6b2+g7c83cef

Apalis_iMX6_LinuxImageV2.6_20160929

This is Toradex's standard build for their Apalis iMX6 on a Ixora carrier. I think they are due for a new major release very soon. I can check if you think it's worth it.

The current firmware is yours (firmware-2-ct-full-community.bin), fresh off your site today. I downloaded board.bin today too.
---------------

root@apalis-imx6:~# lsmod
Module                  Size  Used by
usb_f_rndis            11441  2
u_ether                 9135  1 usb_f_rndis
usb_f_acm               4105  2
u_serial                8487  1 usb_f_acm
ov5640_camera_mipi_int    21588  0
mxc_v4l2_capture       24990  1 ov5640_camera_mipi_int
ipu_bg_overlay_sdc      4113  1 mxc_v4l2_capture
ipu_still               1631  1 mxc_v4l2_capture
ipu_prp_enc             4653  1 mxc_v4l2_capture
max9526_tvin            5800  0
ipu_csi_enc             2917  1 mxc_v4l2_capture
ipu_fg_overlay_sdc      4978  1 mxc_v4l2_capture
adv7280_tvin            6563  0
v4l2_int_device         1759  4
adv7280_tvin,ov5640_camera_mipi_int,mxc_v4l2_capture,max9526_tvin
ath10k_pci             27397  0
ath10k_core           101131  1 ath10k_pci
ath                    17381  1 ath10k_core
mac80211              254675  1 ath10k_core
cfg80211              166770  3 ath,mac80211,ath10k_core
libcomposite           28353  12 usb_f_acm,usb_f_rndis
configfs               20737  4 usb_f_acm,usb_f_rndis,libcomposite
galcore               207484  2

------------

root@apalis-imx6:~# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode
DEFAULT group default
     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group
default qlen 10
     link/can
3: can1: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group
default qlen 10
     link/can
4: eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc
pfifo_fast state UP mode DEFAULT group defaul0
     link/ether 00:14:2d:4a:30:f9 brd ff:ff:ff:ff:ff:ff
5: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group
default
     link/sit 0.0.0.0 brd 0.0.0.0
6: usb0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast
state DOWN mode DEFAULT group default ql0
     link/ether 00:14:2d:ff:ff:ff brd ff:ff:ff:ff:ff:ff

Thanks again,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 9:57pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Please let us know 'lspci' or equiv, exactly what firmware you are loading,
kernel driver version, etc.

Quoted 123 lines

Maybe try LEDE if you can, it's likely more up to date.

Thanks,
Ben

Quoted 116 lines · On 10/24/2016 04:22 PM, [email protected] wrote:

Great, thanks Ben,

That cleared up the firmware load error but I now have:

[    6.997553] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem
0x01000000-0x011ff]
[    7.075559] ath10k: pci irq MSI
[    9.753487] ath10k: ctl_resp never came in (-110)
[    9.758281] ath10k: failed to connect to HTC: -110
[    9.803633] ath10k: could not init core (-110)
[    9.843495] ath10k: could not probe fw (-110)
[    9.843499] ath10k: failed to register driver core: -110
[    9.843681] ath10k_pci: probe of 0000:01:00.0 failed with error -110

Any ideas? Let me know if I should post this new.

Thanks a bunch
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 5:05pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

You need board.bin too. Something like this if you want to use my firmware, or firmware-5.bin for upstream 10.2 firmware:

[root@ben-ota-1 lanforge]# ls -l /lib/firmware/ath10k/QCA988X/hw2.0/ total 1084

(quoted diff) +0 -2
-rw-r--r--. 1 root root   2116 Sep 27 14:43 board.bin
-rw-r--r--. 1 root root 201324 Oct 13 18:48 firmware-2.bin

Thanks,
Ben

Quoted 73 lines · On 10/24/2016 01:59 PM, [email protected] wrote:

Thanks Ben,

Got the location from the website:

root@apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls
firmware-2.bin         firmware-5.bin

I'll figure out how to do some printk's (I'm a newbie).

Thanks,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 4:11pm
To: [email protected], [email protected]
Subject: Re: Direct firmware load failed with error 2

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 39 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more.
I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem
0x01000000-0x011ff]
[ 7.172118] ath10k: pci irq MSI
[ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with
error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.626488] ath10k: could not fetch board data (-2)
[ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with
error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.712302] ath10k: could not fetch board data (-2)
[ 8.722757] ath10k: could not fetch firmware files (-2)
[ 8.781868] ath10k: could not probe fw (-2)
[ 8.781874] ath10k: failed to register driver core: -2
[ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution.
Any help would be greatly appreciated.

Colin McKay

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Quoted 8 lines

--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#10 lore raw

Thankyou both, Ben and Marek,

Based on your advice, we're moving to the Gateworks hardware, which I believe is a much better fit for us.

Thanks again,
Colin

-----Original Message-----
From: ath10k [mailto:[email protected]] On Behalf Of Marek Puzyniak
Sent: Tuesday, October 25, 2016 8:50 AM
To: [email protected]; [email protected]
Subject: Re: Direct firmware load failed with error 2

Hi Colin,

As Ben wrote: you need backports.
You can look at gateworks github for examples how it can be done in yocto. They have recipes for ath10k firmware and backports (compat-wireless):

Ath10k firmware :
https://github.com/Gateworks/meta-gateworks/tree/fido/recipes-connectivity/a
th10k-firmware

and backports
https://github.com/Gateworks/meta-gateworks/tree/fido/recipes-kernel/compat-
wireless

Of course it is not as simple as just adding those recipes, but it is good point to start.

If you need newer ath10k firmware then is is quite easy to update ath10k-firmware recipe.
With compat-wireless it is not so easy but it is possible.

Marek

Quoted 6 lines · Ben Greear

Your kernel is so old that it will likely be a pain to get things working.

You can do backports, and I have manually done some backporting for users with similarly old kernels (using my 3.17 tree is a upstream kernel), but it is not something I do for fun.

Quoted 13 lines

If for some reason stock firmware-2.bin works and mine does not, then let me know and maybe I can help.

Thanks,
Ben

Quoted 5 lines · On 10/24/2016 08:11 PM, [email protected] wrote:

Hi Ben,

Forgot to mention. Our hardware is not supported by OpenWRT, so going to LEDE at this point may be too tough. I'm an RF guy, so this is a steep

hill.

Quoted 42 lines
Quoted 42 lines

Colin

-----Original Message-----
From: [email protected]
Sent: Monday, October 24, 2016 10:59pm
To: "Ben Greear" <[email protected]>
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Hi Ben

root@apalis-imx6:~# lspci -v
00:00.0 PCI bridge: Synopsys, Inc. Device abcd (rev 01) (prog-if 00 
[Normal decode])
         Flags: bus master, fast devsel, latency 0, IRQ 388
         Memory at 01200000 (32-bit, non-prefetchable) [size=1M]
         Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
         Memory behind bridge: 01000000-011fffff
         Prefetchable memory behind bridge: 01300000-013fffff
         [virtual] Expansion ROM at 01400000 [disabled] [size=64K]
         Capabilities: [40] Power Management version 3
         Capabilities: [50] MSI: Enable+ Count=1/1 Maskable+ 64bit+
         Capabilities: [70] Express Root Port (Slot-), MSI 00
         Capabilities: [100] Advanced Error Reporting
         Capabilities: [140] Virtual Channel
         Kernel driver in use: pcieport

01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
Flags: fast devsel, IRQ 155
Memory at 01000000 (64-bit, non-prefetchable) [size=2M] [virtual] Expansion ROM at 01300000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=8/8 Maskable+ 64bit-
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00 Kernel modules: ath10k_pci
----------

Quoted 5 lines
Quoted 5 lines

Angstrom v2015.12 - Kernel 3.14.52-v2.6b2+g7c83cef

Apalis_iMX6_LinuxImageV2.6_20160929

This is Toradex's standard build for their Apalis iMX6 on a Ixora

carrier.

Quoted 168 lines
Quoted 168 lines

I think they are due for a new major release very soon. I can check if you think it's worth it.

The current firmware is yours (firmware-2-ct-full-community.bin), fresh off your site today. I downloaded board.bin today too.
---------------

root@apalis-imx6:~# lsmod
Module                  Size  Used by
usb_f_rndis            11441  2
u_ether                 9135  1 usb_f_rndis
usb_f_acm               4105  2
u_serial                8487  1 usb_f_acm
ov5640_camera_mipi_int    21588  0
mxc_v4l2_capture       24990  1 ov5640_camera_mipi_int
ipu_bg_overlay_sdc      4113  1 mxc_v4l2_capture
ipu_still               1631  1 mxc_v4l2_capture
ipu_prp_enc             4653  1 mxc_v4l2_capture
max9526_tvin            5800  0
ipu_csi_enc             2917  1 mxc_v4l2_capture
ipu_fg_overlay_sdc      4978  1 mxc_v4l2_capture
adv7280_tvin            6563  0
v4l2_int_device         1759  4
adv7280_tvin,ov5640_camera_mipi_int,mxc_v4l2_capture,max9526_tvin
ath10k_pci             27397  0
ath10k_core           101131  1 ath10k_pci
ath                    17381  1 ath10k_core
mac80211              254675  1 ath10k_core
cfg80211              166770  3 ath,mac80211,ath10k_core
libcomposite           28353  12 usb_f_acm,usb_f_rndis
configfs               20737  4 usb_f_acm,usb_f_rndis,libcomposite
galcore               207484  2

------------

root@apalis-imx6:~# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN 
mode DEFAULT group default
     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group 
default qlen 10
     link/can
3: can1: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group 
default qlen 10
     link/can
4: eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc 
pfifo_fast state UP mode DEFAULT group defaul0
     link/ether 00:14:2d:4a:30:f9 brd ff:ff:ff:ff:ff:ff
5: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT 
group default
     link/sit 0.0.0.0 brd 0.0.0.0
6: usb0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc 
pfifo_fast state DOWN mode DEFAULT group default ql0
     link/ether 00:14:2d:ff:ff:ff brd ff:ff:ff:ff:ff:ff

Thanks again,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 9:57pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Please let us know 'lspci' or equiv, exactly what firmware you are loading, kernel driver version, etc.

Maybe try LEDE if you can, it's likely more up to date.

Thanks,
Ben

Quoted 95 lines · On 10/24/2016 04:22 PM, [email protected] wrote:

Great, thanks Ben,

That cleared up the firmware load error but I now have:

[    6.997553] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem
0x01000000-0x011ff]
[    7.075559] ath10k: pci irq MSI
[    9.753487] ath10k: ctl_resp never came in (-110)
[    9.758281] ath10k: failed to connect to HTC: -110
[    9.803633] ath10k: could not init core (-110)
[    9.843495] ath10k: could not probe fw (-110)
[    9.843499] ath10k: failed to register driver core: -110
[    9.843681] ath10k_pci: probe of 0000:01:00.0 failed with error -110

Any ideas? Let me know if I should post this new.

Thanks a bunch
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 5:05pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

You need board.bin too. Something like this if you want to use my firmware, or firmware-5.bin for upstream 10.2 firmware:

[root@ben-ota-1 lanforge]# ls -l /lib/firmware/ath10k/QCA988X/hw2.0/ total 1084

(quoted diff) +0 -2
-rw-r--r--. 1 root root   2116 Sep 27 14:43 board.bin
-rw-r--r--. 1 root root 201324 Oct 13 18:48 firmware-2.bin

Thanks,
Ben

Quoted 54 lines · On 10/24/2016 01:59 PM, [email protected] wrote:

Thanks Ben,

Got the location from the website:

root@apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls
firmware-2.bin         firmware-5.bin

I'll figure out how to do some printk's (I'm a newbie).

Thanks,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 4:11pm
To: [email protected], [email protected]
Subject: Re: Direct firmware load failed with error 2

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 22 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more.
I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 
0x01000000-0x011ff] [ 7.172118] ath10k: pci irq MSI [ 7.198024] 
ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2 
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper [ 
8.626488] ath10k: could not fetch board data (-2) [ 8.648471] 
ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2 
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper [ 

8.712302] ath10k: could not fetch board data (-2) [ 8.722757]
ath10k: could not fetch firmware files (-2) [ 8.781868] ath10k:
could not probe fw (-2) [ 8.781874] ath10k: failed to register driver core: -2 [ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug

this issue.

Quoted 18 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines

And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

Quoted 10 lines
Quoted 9 lines
Quoted 7 lines
Quoted 5 lines

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Quoted 8 lines

--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#11 lore raw

Those two recipes are hardware independent, I mean CPU module and motherboard. For example I am using imx6 cpu but completelly different module provider. You have to take care to have proper kernel and uboot patches for your provider but compat-wireless and ath10k-firmware could be the same for all of them.

Marek

Quoted 307 lines · Colin McKay

Thankyou both, Ben and Marek,

Based on your advice, we're moving to the Gateworks hardware, which I believe is a much better fit for us.

Thanks again,
Colin

-----Original Message-----
From: ath10k [mailto:[email protected]] On Behalf Of Marek Puzyniak
Sent: Tuesday, October 25, 2016 8:50 AM
To: [email protected]; [email protected]
Subject: Re: Direct firmware load failed with error 2

Hi Colin,

As Ben wrote: you need backports.
You can look at gateworks github for examples how it can be done in yocto. They have recipes for ath10k firmware and backports (compat-wireless):

Ath10k firmware :
https://github.com/Gateworks/meta-gateworks/tree/fido/recipes-connectivity/a
th10k-firmware

and backports
https://github.com/Gateworks/meta-gateworks/tree/fido/recipes-kernel/compat-
wireless

Of course it is not as simple as just adding those recipes, but it is good point to start.

If you need newer ath10k firmware then is is quite easy to update ath10k-firmware recipe.
With compat-wireless it is not so easy but it is possible.

Marek

Quoted 6 lines · Ben Greear

Your kernel is so old that it will likely be a pain to get things working.

You can do backports, and I have manually done some backporting for users with similarly old kernels (using my 3.17 tree is a upstream kernel), but it is not something I do for fun.

Quoted 13 lines

If for some reason stock firmware-2.bin works and mine does not, then let me know and maybe I can help.

Thanks,
Ben

Quoted 5 lines · On 10/24/2016 08:11 PM, [email protected] wrote:

Hi Ben,

Forgot to mention. Our hardware is not supported by OpenWRT, so going to LEDE at this point may be too tough. I'm an RF guy, so this is a steep

hill.

Quoted 42 lines
Quoted 42 lines

Colin

-----Original Message-----
From: [email protected]
Sent: Monday, October 24, 2016 10:59pm
To: "Ben Greear" <[email protected]>
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Hi Ben

root@apalis-imx6:~# lspci -v
00:00.0 PCI bridge: Synopsys, Inc. Device abcd (rev 01) (prog-if 00
[Normal decode])
         Flags: bus master, fast devsel, latency 0, IRQ 388
         Memory at 01200000 (32-bit, non-prefetchable) [size=1M]
         Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
         Memory behind bridge: 01000000-011fffff
         Prefetchable memory behind bridge: 01300000-013fffff
         [virtual] Expansion ROM at 01400000 [disabled] [size=64K]
         Capabilities: [40] Power Management version 3
         Capabilities: [50] MSI: Enable+ Count=1/1 Maskable+ 64bit+
         Capabilities: [70] Express Root Port (Slot-), MSI 00
         Capabilities: [100] Advanced Error Reporting
         Capabilities: [140] Virtual Channel
         Kernel driver in use: pcieport

01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
Flags: fast devsel, IRQ 155
Memory at 01000000 (64-bit, non-prefetchable) [size=2M] [virtual] Expansion ROM at 01300000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=8/8 Maskable+ 64bit-
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00 Kernel modules: ath10k_pci
----------

Quoted 5 lines
Quoted 5 lines

Angstrom v2015.12 - Kernel 3.14.52-v2.6b2+g7c83cef

Apalis_iMX6_LinuxImageV2.6_20160929

This is Toradex's standard build for their Apalis iMX6 on a Ixora

carrier.

Quoted 168 lines
Quoted 168 lines

I think they are due for a new major release very soon. I can check if you think it's worth it.

The current firmware is yours (firmware-2-ct-full-community.bin), fresh off your site today. I downloaded board.bin today too.
---------------

root@apalis-imx6:~# lsmod
Module                  Size  Used by
usb_f_rndis            11441  2
u_ether                 9135  1 usb_f_rndis
usb_f_acm               4105  2
u_serial                8487  1 usb_f_acm
ov5640_camera_mipi_int    21588  0
mxc_v4l2_capture       24990  1 ov5640_camera_mipi_int
ipu_bg_overlay_sdc      4113  1 mxc_v4l2_capture
ipu_still               1631  1 mxc_v4l2_capture
ipu_prp_enc             4653  1 mxc_v4l2_capture
max9526_tvin            5800  0
ipu_csi_enc             2917  1 mxc_v4l2_capture
ipu_fg_overlay_sdc      4978  1 mxc_v4l2_capture
adv7280_tvin            6563  0
v4l2_int_device         1759  4
adv7280_tvin,ov5640_camera_mipi_int,mxc_v4l2_capture,max9526_tvin
ath10k_pci             27397  0
ath10k_core           101131  1 ath10k_pci
ath                    17381  1 ath10k_core
mac80211              254675  1 ath10k_core
cfg80211              166770  3 ath,mac80211,ath10k_core
libcomposite           28353  12 usb_f_acm,usb_f_rndis
configfs               20737  4 usb_f_acm,usb_f_rndis,libcomposite
galcore               207484  2

------------

root@apalis-imx6:~# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
mode DEFAULT group default
     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group
default qlen 10
     link/can
3: can1: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group
default qlen 10
     link/can
4: eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc
pfifo_fast state UP mode DEFAULT group defaul0
     link/ether 00:14:2d:4a:30:f9 brd ff:ff:ff:ff:ff:ff
5: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT
group default
     link/sit 0.0.0.0 brd 0.0.0.0
6: usb0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc
pfifo_fast state DOWN mode DEFAULT group default ql0
     link/ether 00:14:2d:ff:ff:ff brd ff:ff:ff:ff:ff:ff

Thanks again,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 9:57pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

Please let us know 'lspci' or equiv, exactly what firmware you are loading, kernel driver version, etc.

Maybe try LEDE if you can, it's likely more up to date.

Thanks,
Ben

Quoted 95 lines · On 10/24/2016 04:22 PM, [email protected] wrote:

Great, thanks Ben,

That cleared up the firmware load error but I now have:

[    6.997553] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem
0x01000000-0x011ff]
[    7.075559] ath10k: pci irq MSI
[    9.753487] ath10k: ctl_resp never came in (-110)
[    9.758281] ath10k: failed to connect to HTC: -110
[    9.803633] ath10k: could not init core (-110)
[    9.843495] ath10k: could not probe fw (-110)
[    9.843499] ath10k: failed to register driver core: -110
[    9.843681] ath10k_pci: probe of 0000:01:00.0 failed with error -110

Any ideas? Let me know if I should post this new.

Thanks a bunch
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 5:05pm
To: [email protected]
Cc: [email protected]
Subject: Re: Direct firmware load failed with error 2

You need board.bin too. Something like this if you want to use my firmware, or firmware-5.bin for upstream 10.2 firmware:

[root@ben-ota-1 lanforge]# ls -l /lib/firmware/ath10k/QCA988X/hw2.0/ total 1084

(quoted diff) +0 -2
-rw-r--r--. 1 root root   2116 Sep 27 14:43 board.bin
-rw-r--r--. 1 root root 201324 Oct 13 18:48 firmware-2.bin

Thanks,
Ben

Quoted 54 lines · On 10/24/2016 01:59 PM, [email protected] wrote:

Thanks Ben,

Got the location from the website:

root@apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls
firmware-2.bin         firmware-5.bin

I'll figure out how to do some printk's (I'm a newbie).

Thanks,
Colin

-----Original Message-----
From: "Ben Greear" <[email protected]>
Sent: Monday, October 24, 2016 4:11pm
To: [email protected], [email protected]
Subject: Re: Direct firmware load failed with error 2

Maybe add some printks in your driver to see exactly what it is trying to load?

Maybe firmware is in wrong location?

errno 2 == ENOENT, which probably means something like 'could not find file'.

Thanks,
Ben

Quoted 22 lines · On 10/24/2016 12:55 PM, [email protected] wrote:

Hi,

I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more.
I keep running into the following error:

[ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem
0x01000000-0x011ff] [ 7.172118] ath10k: pci irq MSI [ 7.198024]
ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper [
8.626488] ath10k: could not fetch board data (-2) [ 8.648471]
ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
[ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper [

8.712302] ath10k: could not fetch board data (-2) [ 8.722757]
ath10k: could not fetch firmware files (-2) [ 8.781868] ath10k:
could not probe fw (-2) [ 8.781874] ath10k: failed to register driver core: -2 [ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug

this issue.

Quoted 18 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines

And the vendors are struggling to get me a solution. Any help would be greatly appreciated.

Colin McKay

Quoted 10 lines
Quoted 9 lines
Quoted 7 lines
Quoted 5 lines

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Quoted 8 lines

--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Quoted 5 lines

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k