Patch "ARM: dts: fix the SD card on the Snowball" has been added to the 4.8-stable tree
Subsystems (2)
This is a note to let you know that I've just added the patch titled
ARM: dts: fix the SD card on the Snowball
to the 4.8-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
arm-dts-fix-the-sd-card-on-the-snowball.patch
and it can be found in the queue-4.8 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree, please let <[email protected]> know about it.
Quoted 1 line
From
1b283eea6228880b765bc40fe4e555416437ce58Mon Sep 17 00:00:00 2001
From: Linus Walleij <[email protected]>
Date: Fri, 7 Oct 2016 10:52:17 +0200
Subject: ARM: dts: fix the SD card on the Snowball
From: Linus Walleij <[email protected]>
commit 1b283eea6228880b765bc40fe4e555416437ce58 upstream.
This fixes a very annoying regression on the Snowball SD card that has been around for a while. It turns out that the device tree does not configure the direction pins properly, nor sets up the pins for the voltage converter properly at boot. Unless all things are correctly set up, the feedback clock will not work, and makes the driver spew messages in the console (but it works, very slowly):
root@Ux500:/ mount /dev/mmcblk0p2 /mnt/
[ 9.953460] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer! [ 9.960296] mmcblk0: error -110 sending status command, retrying [ 9.966461] mmcblk0: error -110 sending status command, retrying [ 9.972534] mmcblk0: error -110 sending status command, aborting
Fix this by rectifying the device tree to correspond to that of the Ux500 HREF boards plus the DAT31DIR setting that is unique for the Snowball, and things start working smoothly. Add in the SDR12 and SDR25 modes which this host can do without any problems.
I don't know if this has ever been correct, sadly. It works after this patch.
--- arch/arm/boot/dts/ste-snowball.dts | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-)
arch/arm/boot/dts/ste-snowball.dts +13 -2
@@ -239,14 +239,25 @@ arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <4>; + cap-sd-highspeed; cap-mmc-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + /* All direction control is used */ + st,sig-dir-cmd; + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-dat31; + st,sig-pin-fbclk; + full-pwr-cycle; vmmc-supply = <&ab8500_ldo_aux3_reg>; vqmmc-supply = <&vmmci>; pinctrl-names = "default", "sleep"; pinctrl-0 = <&sdi0_default_mode>; pinctrl-1 = <&sdi0_sleep_mode>; - cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>; // 218 + /* GPIO218 MMC_CD */ + cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>; status = "okay"; };
@@ -549,7 +560,7 @@ /* VMMCI level-shifter enable */ snowball_cfg3 { pins = "GPIO217_AH12"; - ste,config = <&gpio_out_lo>; + ste,config = <&gpio_out_hi>; }; /* VMMCI level-shifter voltage select */ snowball_cfg4 {
Patches currently in stable-queue which might be from [email protected] are
queue-4.8/gpio-gpio_get_chipinfo_ioctl-fix-line-offset-validation.patch queue-4.8/gpio-gpio_get_line-handle-event-_ioctl-fix-file-descriptor-leak.patch queue-4.8/gpio-gpio_get_chipinfo_ioctl-fix-information-leak.patch queue-4.8/gpio-gpio_get_lineevent_ioctl-reject-invalid-line-and-event-flags.patch queue-4.8/gpio-gpiohandle_get_line_values_ioctl-fix-another-information-leak.patch queue-4.8/gpio-acpi-fix-returned-error-from-acpi_dev_gpio_irq_get.patch queue-4.8/gpio-gpio_get_linehandle_ioctl-reject-invalid-line-flags.patch queue-4.8/gpio-gpio_get_lineevent_ioctl-validate-line-offset.patch queue-4.8/arm-dts-fix-the-sd-card-on-the-snowball.patch queue-4.8/gpio-gpiohandle_get_line_values_ioctl-fix-information-leak.patch queue-4.8/gpio-gpio_get_linehandle_ioctl-validate-line-offset.patch