b: re-queue tx dma request on herror
Subsystems (2)
PATCH 1/1 b: re-queue tx dma request on herror
Some times dma transfer to usb endpoint fails:
[ 78.378283] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 78.410763] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 3400, dma [ 78.410896] musb-hdrc musb-hdrc.1.auto: complete dc01eb00 usb_api_blocking_completion+0x0/0x24 [usbcore] (0), dev4 ep1out, 10/10 [ 78.411181] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 periodic slot 10 [ 78.411205] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 urb dc01eb00 dev4 ep1out-intr, hw_ep 10, dd624d00/10 [ 78.411223] musb-hdrc musb-hdrc.1.auto: --> hw10 urb dc01eb00 spd2 dev4 ep1out h_addr83 h_port02 bytes 10 [ 78.411244] musb-hdrc musb-hdrc.1.auto: check whether there's still time for periodic Tx [ 78.411256] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 78.443762] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 3500, dma
success transmition:
[ 78.443889] musb-hdrc musb-hdrc.1.auto: complete dc01eb00 usb_api_blocking_completion+0x0/0x24 [usbcore] (0), dev4 ep1out, 10/10 [ 78.444170] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 periodic slot 10 [ 78.444195] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 urb dc01eb00 dev4 ep1out-intr, hw_ep 10, dd624d00/10 [ 78.444213] musb-hdrc musb-hdrc.1.auto: --> hw10 urb dc01eb00 spd2 dev4 ep1out h_addr83 h_port02 bytes 10 [ 78.444232] musb-hdrc musb-hdrc.1.auto: check whether there's still time for periodic Tx [ 78.444245] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 78.540761] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 3504, dma
failed transmission:
[ 78.540780] musb-hdrc musb-hdrc.1.auto: TX 3strikes on ep=10 set ETIMEDOUT [ 78.540897] musb-hdrc musb-hdrc.1.auto: complete dc01eb00 usb_api_blocking_completion+0x0/0x24 [usbcore] (-110), dev4 ep1out, 10/10 [ 78.540945] musb-hdrc musb-hdrc.1.auto: extra TX10 ready, csr 2500 [ 78.540989] usb 2-1.1.2: urb wait ok but retval -110
Use to reproduce is writes to /dev/hidraw0 device which end up with early unexpected timeout and -110 errno set.
Code sets timeout to 5 seconds vfs_write()->hidraw_write()->hidraw_send_report()->usbhid_output_report()
ret = usb_interrupt_msg(dev, usbhid->urbout->pipe,
buf, count, &actual_length, USB_CTRL_SET_TIMEOUT);
where is set to 5 second:
when it wents to usb_start_wait_urb() where waits for completition:
retval = usb_submit_urb(urb, GFP_NOIO);
expire = timeout ? msecs_to_jiffies(timeout) : MAX_SCHEDULE_TIMEOUT;
if (!wait_for_completion_timeout(&ctx.done, expire)) {So user space application expects that write will be done in 5 seconds or error will happen. But musb driver exists this logic on first dma error without trying to retransmit current urb. This patch adds current request to the end of list, destroys current dma transfer and renew transmission. In that case this urb transmitted in next cycle and not failing with error before timeout.
--- drivers/usb/musb/musb_host.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/usb/musb/musb_host.c +4 -4
@@ -1293,11 +1293,11 @@ void musb_host_tx(struct musb *musb, u8 epnum) status = -EPIPE ; }else if (tx_csr &MUSB_TXCSR_H_ERROR ) { -/* (NON-ISO) dma was disabled, fifo flushed */ musb_dbg (musb,"TX 3strikes on ep=%d" , epnum); - - status = -ETIMEDOUT ; - +if (dma) +musb_bulk_nak_timeout (musb, hw_ep,0 ); +else + status = -ETIMEDOUT ; }else if (tx_csr &MUSB_TXCSR_H_NAKTIMEOUT ) {if (USB_ENDPOINT_XFER_BULK == qh->type && qh->mux ==1 && !list_is_singular (&musb->out_bulk)) {
Signature · 1 line
1.9.1
Hi,
Quoted 11 lines · Max Uvarov
Some times dma transfer to usb endpoint fails:
[ 78.378283] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 78.410763] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 3400, dma [ 78.410896] musb-hdrc musb-hdrc.1.auto: complete dc01eb00 usb_api_blocking_completion+0x0/0x24 [usbcore] (0), dev4 ep1out, 10/10 [ 78.411181] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 periodic slot 10 [ 78.411205] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 urb dc01eb00 dev4 ep1out-intr, hw_ep 10, dd624d00/10 [ 78.411223] musb-hdrc musb-hdrc.1.auto: --> hw10 urb dc01eb00 spd2 dev4 ep1out h_addr83 h_port02 bytes 10 [ 78.411244] musb-hdrc musb-hdrc.1.auto: check whether there's still time for periodic Tx [ 78.411256] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 78.443762] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 3500, dma
What kernel version is this? Log format looks old.
Quoted 20 lines
success transmition:
[ 78.443889] musb-hdrc musb-hdrc.1.auto: complete dc01eb00 usb_api_blocking_completion+0x0/0x24 [usbcore] (0), dev4 ep1out, 10/10 [ 78.444170] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 periodic slot 10 [ 78.444195] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 urb dc01eb00 dev4 ep1out-intr, hw_ep 10, dd624d00/10 [ 78.444213] musb-hdrc musb-hdrc.1.auto: --> hw10 urb dc01eb00 spd2 dev4 ep1out h_addr83 h_port02 bytes 10 [ 78.444232] musb-hdrc musb-hdrc.1.auto: check whether there's still time for periodic Tx [ 78.444245] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 78.540761] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 3504, dmafailed transmission:
[ 78.540780] musb-hdrc musb-hdrc.1.auto: TX 3strikes on ep=10 set ETIMEDOUT [ 78.540897] musb-hdrc musb-hdrc.1.auto: complete dc01eb00 usb_api_blocking_completion+0x0/0x24 [usbcore] (-110), dev4 ep1out, 10/10 [ 78.540945] musb-hdrc musb-hdrc.1.auto: extra TX10 ready, csr 2500 [ 78.540989] usb 2-1.1.2: urb wait ok but retval -110Use to reproduce is writes to
/dev/hidraw0device which end up with early unexpected timeout and -110 errno set.
Quoted 6 lines
Code sets timeout to 5 seconds vfs_write()->hidraw_write()->hidraw_send_report()->usbhid_output_report()
ret = usb_interrupt_msg(dev,usbhid->urbout->pipe,
buf, count,&actual_length,USB_CTRL_SET_TIMEOUT);
where is set to 5 second:
The two timeout here are completely different - ETIMEOUT on 3strikes vs. USB_CTRL_SET_TIMEOUT.
USB_CTRL_SET_TIMEOUT only takes effects when the usb device NAK the interrupt transaction for 5 seconds.
But when MUSB reports 3strikes ETIMEOUT, it means the usb device doesn't respond, no handshake packet at all. The host tried TX 3 times, all received no response handshake, so ETIMEOUT.
Quoted 8 lines
when it wents to
usb_start_wait_urb()where waits for completition:retval = usb_submit_urb(urb, GFP_NOIO); expire = timeout ? msecs_to_jiffies(timeout) : MAX_SCHEDULE_TIMEOUT; if (!wait_for_completion_timeout(&ctx.done, expire)) {So user space application expects that write will be done in 5 seconds or error will happen. But musb driver exists this logic on first dma error
This ETIMEOUT is not a dma error, but something wrong on the wire which causes the usb device is unable to respond, typically not received the TX packet at all.
Quoted 1 line
without trying to retransmit current urb. This patch adds current request
The host does trying to retransmit the TX packet 3 times, before reports ETIMEOUT.
Quoted 3 lines
to the end of list, destroys current dma transfer and renew transmission. In that case this urb transmitted in next cycle and not failing with error before timeout.
NAK.
It is up to the application to retry the transaction,
Regards,
-Bin.
Quoted 29 lines
Signed-off-by Max Uvarov <[email protected]>--- drivers/usb/musb/musb_host.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)drivers/usb/musb/musb_host.c +4
-4@@ -1293,11 +1293,11 @@ void musb_host_tx(struct musb *musb, u8 epnum) status = -EPIPE ; }else if (tx_csr &MUSB_TXCSR_H_ERROR ) { -/* (NON-ISO) dma was disabled, fifo flushed */ musb_dbg (musb,"TX 3strikes on ep=%d" , epnum); - - status = -ETIMEDOUT ; - +if (dma) +musb_bulk_nak_timeout (musb, hw_ep,0 ); +else + status = -ETIMEDOUT ; }else if (tx_csr &MUSB_TXCSR_H_NAKTIMEOUT ) {if (USB_ENDPOINT_XFER_BULK == qh->type && qh->mux ==1 && !list_is_singular (&musb->out_bulk)) {Signature · 1 line
1.9.1
Hello Bin,
thanks for decoding errors. I was able to reproduce it with the latest master while logs are for 4.1 kernel. The main reason was 25 mhz generator instead of 24 on remote hid device. With replacing everything looks better, i.e. hidraw can operate 3-4 days and then the same continuous musb 3-strikes. It might be some buggy device or some other issue with continues writes to /dev/hidraw.
please do not apply this patch.
Thanks,
Maxim.
2016-11-29 6:39 GMT+03:00 Bin Liu <[email protected]>:
Quoted 112 lines
Hi,
Quoted 11 lines · Max Uvarov
Some times dma transfer to usb endpoint fails:
[ 78.378283] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 78.410763] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 3400, dma [ 78.410896] musb-hdrc musb-hdrc.1.auto: complete dc01eb00 usb_api_blocking_completion+0x0/0x24 [usbcore] (0), dev4 ep1out, 10/10 [ 78.411181] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 periodic slot 10 [ 78.411205] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 urb dc01eb00 dev4 ep1out-intr, hw_ep 10, dd624d00/10 [ 78.411223] musb-hdrc musb-hdrc.1.auto: --> hw10 urb dc01eb00 spd2 dev4 ep1out h_addr83 h_port02 bytes 10 [ 78.411244] musb-hdrc musb-hdrc.1.auto: check whether there's still time for periodic Tx [ 78.411256] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 78.443762] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 3500, dmaWhat kernel version is this? Log format looks old.
Quoted 20 lines
success transmition:
[ 78.443889] musb-hdrc musb-hdrc.1.auto: complete dc01eb00 usb_api_blocking_completion+0x0/0x24 [usbcore] (0), dev4 ep1out, 10/10 [ 78.444170] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 periodic slot 10 [ 78.444195] musb-hdrc musb-hdrc.1.auto: qh dc01ed00 urb dc01eb00 dev4 ep1out-intr, hw_ep 10, dd624d00/10 [ 78.444213] musb-hdrc musb-hdrc.1.auto: --> hw10 urb dc01eb00 spd2 dev4 ep1out h_addr83 h_port02 bytes 10 [ 78.444232] musb-hdrc musb-hdrc.1.auto: check whether there's still time for periodic Tx [ 78.444245] musb-hdrc musb-hdrc.1.auto: Start TX10 dma [ 78.540761] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 3504, dmafailed transmission:
[ 78.540780] musb-hdrc musb-hdrc.1.auto: TX 3strikes on ep=10 set ETIMEDOUT [ 78.540897] musb-hdrc musb-hdrc.1.auto: complete dc01eb00 usb_api_blocking_completion+0x0/0x24 [usbcore] (-110), dev4 ep1out, 10/10 [ 78.540945] musb-hdrc musb-hdrc.1.auto: extra TX10 ready, csr 2500 [ 78.540989] usb 2-1.1.2: urb wait ok but retval -110Use to reproduce is writes to
/dev/hidraw0device which end up with early unexpected timeout and -110 errno set.Quoted 6 lines
Code sets timeout to 5 seconds vfs_write()->hidraw_write()->hidraw_send_report()->usbhid_output_report()
ret = usb_interrupt_msg(dev,usbhid->urbout->pipe,
buf, count,&actual_length,USB_CTRL_SET_TIMEOUT);
where is set to 5 second:The two timeout here are completely different - ETIMEOUT on 3strikes vs.
USB_CTRL_SET_TIMEOUT.
USB_CTRL_SET_TIMEOUTonly takes effects when the usb device NAK the interrupt transaction for 5 seconds.But when MUSB reports 3strikes ETIMEOUT, it means the usb device doesn't respond, no handshake packet at all. The host tried TX 3 times, all received no response handshake, so ETIMEOUT.
Quoted 8 lines
when it wents to
usb_start_wait_urb()where waits for completition:retval = usb_submit_urb(urb, GFP_NOIO); expire = timeout ? msecs_to_jiffies(timeout) : MAX_SCHEDULE_TIMEOUT; if (!wait_for_completion_timeout(&ctx.done, expire)) {So user space application expects that write will be done in 5 seconds or error will happen. But musb driver exists this logic on first dma error
This ETIMEOUT is not a dma error, but something wrong on the wire which causes the usb device is unable to respond, typically not received the TX packet at all.
Quoted 1 line
without trying to retransmit current urb. This patch adds current request
The host does trying to retransmit the TX packet 3 times, before reports ETIMEOUT.
Quoted 3 lines
to the end of list, destroys current dma transfer and renew transmission. In that case this urb transmitted in next cycle and not failing with error before timeout.
NAK.
It is up to the application to retry the transaction,
Regards,
-Bin.Quoted 29 lines
Signed-off-by Max Uvarov <[email protected]>--- drivers/usb/musb/musb_host.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)drivers/usb/musb/musb_host.c +4
-5@@ -1293,11 +1293,11 @@ void musb_host_tx(struct musb *musb, u8 epnum) status = -EPIPE ; }else if (tx_csr &MUSB_TXCSR_H_ERROR ) { -/* (NON-ISO) dma was disabled, fifo flushed */ musb_dbg (musb,"TX 3strikes on ep=%d" , epnum); - - status = -ETIMEDOUT ; - +if (dma) +musb_bulk_nak_timeout (musb, hw_ep,0 ); +else + status = -ETIMEDOUT ; }else if (tx_csr &MUSB_TXCSR_H_NAKTIMEOUT ) {if (USB_ENDPOINT_XFER_BULK == qh->type && qh->mux ==1 && !list_is_singular (&musb->out_bulk)) { --1.9.1
Signature · 2 lines
Best regards, Maxim Uvarov