net: qcom/emac:
Subsystems (3)
cover net: qcom/emac:
Although not related, these patches affect the same files, so they should be applied in order.
The first patch cleans up logging of when the the phy driver is attached.
The second patch always configures the SGMII to use autonegotiation mode.
The third patch removes a redundant call to emac_mac_start().
The fourth patch removes some extraneous non-functioning WOL code.
The fifth patch adds an error handler for the SGMII block.
Timur Tabi (5):
[net-next] net: qcom/emac: display the phy driver info after we
connect
[net-next] net: qcom/emac: always use autonegotiation to configure the
SGMII link
[net-next] net: qcom/emac: do not call emac_mac_start twice [net-next] net: qcom/emac: remove extraneous wake-on-lan code [net-next] net: qcom/emac: add an error interrupt handler for the
sgmii
drivers/net/ethernet/qualcomm/emac/emac-mac.c | 24 ++-- drivers/net/ethernet/qualcomm/emac/emac-mac.h | 1 - drivers/net/ethernet/qualcomm/emac/emac-phy.c | 3 - drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 175 ++++++++++++++++++------ drivers/net/ethernet/qualcomm/emac/emac-sgmii.h | 16 ++- drivers/net/ethernet/qualcomm/emac/emac.c | 10 +- drivers/net/ethernet/qualcomm/emac/emac.h | 4 - 7 files changed, 166 insertions(+), 67 deletions(-)
Signature · 3 lines
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
PATCH 4/4 net: qcom/emac: add an error interrupt handler for the sgmii
The SGMII (internal PHY) can report decode errors via an interrupt. It can also report autonegotiation status changes, but we don't need to track those. The SGMII can recover automatically from most decode errors, so we only reset the interface if we get multiple consecutive errors.
It's possible for bogus decode errors to be reported while the link is being brought up. The interrupt is registered when the interface is opened, and it's enabled after the link is up.
--- drivers/net/ethernet/qualcomm/emac/emac-mac.c | 8 +- drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 126 +++++++++++++++++++++++- drivers/net/ethernet/qualcomm/emac/emac-sgmii.h | 16 ++- drivers/net/ethernet/qualcomm/emac/emac.c | 10 ++ 4 files changed, 153 insertions(+), 7 deletions(-)
drivers/net/ethernet/qualcomm/emac/emac-mac.c +6 -2
@@ -961,12 +961,16 @@ static void emac_mac_rx_descs_refill(struct emac_adapter *adpt,static void emac_adjust_link (struct net_device *netdev) {struct emac_adapter *adpt =netdev_priv (netdev); +struct emac_sgmii *sgmii = &adpt->phy;struct phy_device *phydev = netdev->phydev; -if (phydev->link) +if (phydev->link) {emac_mac_start (adpt); -else + sgmii->link_up (adpt); + }else { + sgmii->link_down (adpt);emac_mac_stop (adpt); + }phy_print_status (phydev); }
drivers/net/ethernet/qualcomm/emac/emac-sgmii.c +123 -3
179 lines not on this page · raw message
drivers/net/ethernet/qualcomm/emac/emac-sgmii.h +14 -2
@@ -16,17 +16,29 @@struct emac_adapter ;struct platform_device ; -typedef int (*emac_sgmii_initialize )(struct emac_adapter *adpt); +typedef int (*emac_sgmii_function )(struct emac_adapter *adpt);/** emac_sgmii - internal emac phy * @base base address * @digital per-lane digital block +* @irq the interrupt number +* @decode_error_count reference count of consecutive decode errors * @initialize initialization function +* @open called when the driver is opened +* @close called when the driver is closed +* @link_up called when the link comes up +* @link_down called when the link comes down */ struct emac_sgmii {void __iomem *base;void __iomem *digital; -emac_sgmii_initialize initialize; +unsigned int irq; +atomic_t decode_error_count; +emac_sgmii_function initialize; +emac_sgmii_function open; +emac_sgmii_function close; +emac_sgmii_function link_up; +emac_sgmii_function link_down; };int emac_sgmii_config (struct platform_device *pdev,struct emac_adapter *adpt);
drivers/net/ethernet/qualcomm/emac/emac.c +10 -0
@@ -280,6 +280,14 @@ static int emac_open(struct net_device *netdev)return ret; } + ret = adpt->phy.open (adpt); +if (ret) { +emac_mac_down (adpt); +emac_mac_rx_tx_rings_free_all (adpt); +free_irq (irq->irq, irq); +return ret; + } +return 0 ; }
@@ -290,6 +298,7 @@ static int emac_close(struct net_device *netdev)mutex_lock (&adpt->reset_lock); + adpt->phy.close (adpt);emac_mac_down (adpt);emac_mac_rx_tx_rings_free_all (adpt);
@@ -645,6 +654,7 @@ static int emac_probe(struct platform_device *pdev) adpt->msg_enable =EMAC_MSG_DEFAULT ; phy = &adpt->phy; +atomic_set (&phy->decode_error_count,0 );mutex_init (&adpt->reset_lock);spin_lock_init (&adpt->stats.lock);
Signature · 3 lines
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
PATCH 2/5 net: qcom/emac: always use autonegotiation to configure the SGMII link
In reply to Timur TabiRegardless of how the external PHY is configured, the internal PHY (the "SGMII" block) is capable of configuring the SGMII link automatically. When the external PHY link comes up, regardless of how it is configured, the SGMII link is configured automatically.
--- drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 49 +++++-------------------- 1 file changed, 10 insertions(+), 39 deletions(-)
drivers/net/ethernet/qualcomm/emac/emac-sgmii.c +10 -39
@@ -47,44 +47,19 @@#define SERDES_START_WAIT_TIMES 100 -static int emac_sgmii_link_init (struct emac_adapter *adpt) +/* Initialize the SGMII link between the internal and external PHYs. */ +static void emac_sgmii_link_init (struct emac_adapter *adpt) { -struct phy_device *phydev = adpt->phydev;struct emac_sgmii *phy = &adpt->phy;u32 val; +/* Always use autonegotiation. It works no matter how the external +* PHY is configured. +*/ val =readl (phy->base +EMAC_SGMII_PHY_AUTONEG_CFG2 ); - -if (phydev->autoneg ==AUTONEG_ENABLE ) { - val &= ~(FORCE_AN_RX_CFG |FORCE_AN_TX_CFG ); - val |=AN_ENABLE ; -writel (val, phy->base +EMAC_SGMII_PHY_AUTONEG_CFG2 ); - }else { -u32 speed_cfg; - -switch (phydev->speed) { -case SPEED_10 : - speed_cfg =SPDMODE_10 ; -break ; -case SPEED_100 : - speed_cfg =SPDMODE_100 ; -break ; -case SPEED_1000 : - speed_cfg =SPDMODE_1000 ; -break ; -default : -return -EINVAL ; - } - -if (phydev->duplex ==DUPLEX_FULL ) - speed_cfg |=DUPLEX_MODE ; - - val &= ~AN_ENABLE ; -writel (speed_cfg, phy->base +EMAC_SGMII_PHY_SPEED_CFG1 ); -writel (val, phy->base +EMAC_SGMII_PHY_AUTONEG_CFG2 ); - } - -return 0 ; + val &= ~(FORCE_AN_RX_CFG |FORCE_AN_TX_CFG ); + val |=AN_ENABLE ; +writel (val, phy->base +EMAC_SGMII_PHY_AUTONEG_CFG2 ); }static int emac_sgmii_irq_clear (struct emac_adapter *adpt,u32 irq_bits)
@@ -145,12 +120,7 @@ void emac_sgmii_reset(struct emac_adapter *adpt)int ret;emac_sgmii_reset_prepare (adpt); - - ret =emac_sgmii_link_init (adpt); -if (ret) { -netdev_err (adpt->netdev,"unsupported link speed\n" ); -return ; - } +emac_sgmii_link_init (adpt); ret = adpt->phy.initialize (adpt);if (ret)
@@ -287,6 +257,7 @@ int emac_sgmii_config(struct platform_device *pdev, struct emac_adapter *adpt) goto error;emac_sgmii_irq_clear (adpt,SGMII_PHY_INTERRUPT_ERR ); +emac_sgmii_link_init (adpt);/* We've remapped the addresses, so we don't need the device any * more. of_find_device_by_node() says we should release it.
Signature · 3 lines
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
PATCH 4/5 net: qcom/emac: remove extraneous wake-on-lan code
In reply to Timur TabiThe EMAC driver does not support wake-on-lan, but there is still code left-over that partially enables it. Remove that code and a few macros that support it.
--- drivers/net/ethernet/qualcomm/emac/emac-mac.c | 10 ---------- drivers/net/ethernet/qualcomm/emac/emac.h | 4 ---- 2 files changed, 14 deletions(-)
drivers/net/ethernet/qualcomm/emac/emac-mac.c +0 -10
@@ -103,14 +103,6 @@#define RXEN 0x00000002#define TXEN 0x00000001 - -/* EMAC_WOL_CTRL0 */ -#define LK_CHG_PME 0x20 -#define LK_CHG_EN 0x10 -#define MG_FRAME_PME 0x8 -#define MG_FRAME_EN 0x4 -#define WK_FRAME_EN 0x1 -/* EMAC_DESC_CTRL_3 */ #define RFD_RING_SIZE_BMSK 0xfff
@@ -619,8 +611,6 @@ static void emac_mac_start(struct emac_adapter *adpt)emac_reg_update32 (adpt->base +EMAC_ATHR_HEADER_CTRL , (HEADER_ENABLE |HEADER_CNT_EN ),0 ); - -emac_reg_update32 (adpt->csr +EMAC_EMAC_WRAPPER_CSR2 ,0 ,WOL_EN ); }void emac_mac_stop (struct emac_adapter *adpt)
drivers/net/ethernet/qualcomm/emac/emac.h +0 -4
@@ -167,10 +167,6 @@ enum emac_clk_id {#define EMAC_MAX_SETUP_LNK_CYCLE 100 -/* Wake On Lan */ -#define EMAC_WOL_PHY 0x00000001/* PHY Status Change */ -#define EMAC_WOL_MAGIC 0x00000002/* Magic Packet */ -struct emac_stats {/* rx */ u64 rx_ok;/* good packets */
Signature · 3 lines
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
PATCH 5/5 net: qcom/emac: add an error interrupt handler for the sgmii
In reply to Timur TabiThe SGMII (internal PHY) can report decode errors via an interrupt. It can also report autonegotiation status changes, but we don't need to track those. The SGMII can recover automatically from most decode errors, so we only reset the interface if we get multiple consecutive errors.
It's possible for bogus decode errors to be reported while the link is being brought up. The interrupt is registered when the interface is opened, and it's enabled after the link is up.
--- drivers/net/ethernet/qualcomm/emac/emac-mac.c | 8 +- drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 126 +++++++++++++++++++++++- drivers/net/ethernet/qualcomm/emac/emac-sgmii.h | 16 ++- drivers/net/ethernet/qualcomm/emac/emac.c | 10 ++ 4 files changed, 153 insertions(+), 7 deletions(-)
drivers/net/ethernet/qualcomm/emac/emac-mac.c +6 -2
@@ -951,12 +951,16 @@ static void emac_mac_rx_descs_refill(struct emac_adapter *adpt,static void emac_adjust_link (struct net_device *netdev) {struct emac_adapter *adpt =netdev_priv (netdev); +struct emac_sgmii *sgmii = &adpt->phy;struct phy_device *phydev = netdev->phydev; -if (phydev->link) +if (phydev->link) {emac_mac_start (adpt); -else + sgmii->link_up (adpt); + }else { + sgmii->link_down (adpt);emac_mac_stop (adpt); + }phy_print_status (phydev); }
drivers/net/ethernet/qualcomm/emac/emac-sgmii.c +123 -3
179 lines not on this page · raw message
drivers/net/ethernet/qualcomm/emac/emac-sgmii.h +14 -2
@@ -16,17 +16,29 @@struct emac_adapter ;struct platform_device ; -typedef int (*emac_sgmii_initialize )(struct emac_adapter *adpt); +typedef int (*emac_sgmii_function )(struct emac_adapter *adpt);/** emac_sgmii - internal emac phy * @base base address * @digital per-lane digital block +* @irq the interrupt number +* @decode_error_count reference count of consecutive decode errors * @initialize initialization function +* @open called when the driver is opened +* @close called when the driver is closed +* @link_up called when the link comes up +* @link_down called when the link comes down */ struct emac_sgmii {void __iomem *base;void __iomem *digital; -emac_sgmii_initialize initialize; +unsigned int irq; +atomic_t decode_error_count; +emac_sgmii_function initialize; +emac_sgmii_function open; +emac_sgmii_function close; +emac_sgmii_function link_up; +emac_sgmii_function link_down; };int emac_sgmii_config (struct platform_device *pdev,struct emac_adapter *adpt);
drivers/net/ethernet/qualcomm/emac/emac.c +10 -0
@@ -280,6 +280,14 @@ static int emac_open(struct net_device *netdev)return ret; } + ret = adpt->phy.open (adpt); +if (ret) { +emac_mac_down (adpt); +emac_mac_rx_tx_rings_free_all (adpt); +free_irq (irq->irq, irq); +return ret; + } +return 0 ; }
@@ -290,6 +298,7 @@ static int emac_close(struct net_device *netdev)mutex_lock (&adpt->reset_lock); + adpt->phy.close (adpt);emac_mac_down (adpt);emac_mac_rx_tx_rings_free_all (adpt);
@@ -645,6 +654,7 @@ static int emac_probe(struct platform_device *pdev) adpt->msg_enable =EMAC_MSG_DEFAULT ; phy = &adpt->phy; +atomic_set (&phy->decode_error_count,0 );mutex_init (&adpt->reset_lock);spin_lock_init (&adpt->stats.lock);
Signature · 3 lines
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
PATCH 1/5 net: qcom/emac: display the phy driver info after we connect
In reply to Timur TabiThe PHY driver is attached only when the driver calls phy_connect_direct(). Calling phy_attached_print() to display information about the PHY driver prior to that point is meaningless. The interface can be brought down, a new PHY driver can be loaded, and the interface then brought back up. This is the correct time to display information about the attached driver.
Since phy_attached_print() also prints information about the interrupt, that needs to be set as well.
--- drivers/net/ethernet/qualcomm/emac/emac-mac.c | 4 +++- drivers/net/ethernet/qualcomm/emac/emac-phy.c | 3 --- 2 files changed, 3 insertions(+), 4 deletions(-)
drivers/net/ethernet/qualcomm/emac/emac-mac.c +3 -1
@@ -981,6 +981,7 @@ int emac_mac_up(struct emac_adapter *adpt)emac_mac_config (adpt);emac_mac_rx_descs_refill (adpt, &adpt->rx_q); + adpt->phydev->irq =PHY_IGNORE_INTERRUPT ; ret =phy_connect_direct (netdev, adpt->phydev, emac_adjust_link,PHY_INTERFACE_MODE_SGMII );if (ret) {
@@ -988,11 +989,12 @@ int emac_mac_up(struct emac_adapter *adpt)return ret; } +phy_attached_print (adpt->phydev,NULL ); +/* enable mac irq */ writel ((u32 )~DIS_INT , adpt->base +EMAC_INT_STATUS );writel (adpt->irq.mask, adpt->base +EMAC_INT_MASK ); - adpt->phydev->irq =PHY_IGNORE_INTERRUPT ;phy_start (adpt->phydev);napi_enable (&adpt->rx_q.napi);
drivers/net/ethernet/qualcomm/emac/emac-phy.c +0 -3
@@ -226,8 +226,5 @@ int emac_phy_config(struct platform_device *pdev, struct emac_adapter *adpt)return -ENODEV ; } -if (adpt->phydev->drv) -phy_attached_print (adpt->phydev,NULL ); -return 0 ; }
Signature · 3 lines
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
PATCH 3/5 net: qcom/emac: do not call emac_mac_start twice
In reply to Timur Tabiemac_mac_start() uses information from the external PHY to program the MAC, so it makes no sense to call it before the link is up.
--- drivers/net/ethernet/qualcomm/emac/emac-mac.c | 2 +- drivers/net/ethernet/qualcomm/emac/emac-mac.h | 1 - drivers/net/ethernet/qualcomm/emac/emac.c | 2 -- 3 files changed, 1 insertion(+), 4 deletions(-)
drivers/net/ethernet/qualcomm/emac/emac-mac.c +1 -1
@@ -556,7 +556,7 @@ void emac_mac_reset(struct emac_adapter *adpt)emac_reg_update32 (adpt->base +EMAC_DMA_MAS_CTRL ,0 ,INT_RD_CLR_EN ); } -void emac_mac_start (struct emac_adapter *adpt) +static void emac_mac_start (struct emac_adapter *adpt) {struct phy_device *phydev = adpt->phydev;u32 mac, csr1;
drivers/net/ethernet/qualcomm/emac/emac-mac.h +0 -1
@@ -230,7 +230,6 @@ struct emac_tx_queue {int emac_mac_up (struct emac_adapter *adpt);void emac_mac_down (struct emac_adapter *adpt);void emac_mac_reset (struct emac_adapter *adpt); -void emac_mac_start (struct emac_adapter *adpt);void emac_mac_stop (struct emac_adapter *adpt);void emac_mac_mode_config (struct emac_adapter *adpt); void emac_mac_rx_process(struct emac_adapter *adpt, struct emac_rx_queue *rx_q,
drivers/net/ethernet/qualcomm/emac/emac.c +0 -2
@@ -280,8 +280,6 @@ static int emac_open(struct net_device *netdev)return ret; } -emac_mac_start (adpt); -return 0 ; }
Signature · 3 lines
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
Re: [PATCH 4/4] [net-next] net: qcom/emac: add an error interrupt handler for the sgmii
In reply to Timur TabiQuoted 10 lines · Timur Tabi
The SGMII (internal PHY) can report decode errors via an interrupt. It can also report autonegotiation status changes, but we don't need to track those. The SGMII can recover automatically from most decode errors, so we only reset the interface if we get multiple consecutive errors.
It's possible for bogus decode errors to be reported while the link is being brought up. The interrupt is registered when the interface is opened, and it's enabled after the link is up.
Signed-off-by Timur Tabi <[email protected]>
Sorry, this particular patch wasn't meant to be in the patchset. Please ignore it.
Signature · 3 lines
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc. Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
David Miller
maintainerFrom: Timur Tabi <[email protected]>
Date: Fri, 27 Jan 2017 16:43:42 -0600
Quoted 5 lines
Although not related, these patches affect the same files, so they should be applied in order.
The first patch cleans up logging of when the the phy driver is attached.
Quoted 7 lines
The second patch always configures the SGMII to use autonegotiation mode.
The third patch removes a redundant call to
emac_mac_start().The fourth patch removes some extraneous non-functioning WOL code.
The fifth patch adds an error handler for the SGMII block.
Series applied, thanks.