Skip to contentSkip to conversation

HDMI 2.0: Scrambling in DRM layer

PATCH Superseded Shashank Sharma 4 participants 13 messages Feb 28, 2017 – Mar 3, 2017

Subsystems (4)

v5 of 10 Superseded Latest is v10 →

lore
Share & tools
lore
#0 lore raw

v5 cover HDMI 2.0: Scrambling in DRM layer

HDMI 2.0 spec defines a method to reduce the RF footprint while operating at higher pixel clocks, which is called Scrambling. Scrambling can be controlled over a new set of I2C registers which are accessible over existing DDC I2C lines, called SCDC register set.

This patch series contains 6 patches:
- First two patches add generic drm helper functions to read and write into SCDC registers. These patches are written by Thierry, in a patch series published here:
https://patchwork.kernel.org/patch/9459051/
Minor changes were done to map the patches into this series.

- Next two patches add functions for scrambling detection and scrambling control.

- Next two patches use this infrastructure in DRM layer from I915 driver, to enable scrambling on a GLK deivce which sports a native HDMI 2.0 controller.

V2:
- addressed review comments from Thierry, Ville and Dhinakaran
- added signed-off-by:self in first two patches(Jani N)

V3:
- addressed review comments from Jose and Jani

V4:
- addressed review comments from Maarten on patch 5, rebase all other patches

V5:
- addressed review comments from Ville/Ander on patch 1, 4, 5 rebase all other patches

Shashank Sharma (4):
drm/edid: detect SCDC support in HF-VSDB
drm/edid: detect SCDC support in HF-VSDB
drm/i915: enable scrambling
drm/i915: allow HDMI 2.0 clock rates

Thierry Reding (2):
drm: Add SCDC helpers
drm/edid: check for HF-VSDB block

 Documentation/gpu/drm-kms-helpers.rst |  12 ++
 drivers/gpu/drm/Makefile              |   3 +-
 drivers/gpu/drm/drm_edid.c            |  60 +++++++++
 drivers/gpu/drm/drm_scdc_helper.c     | 234 ++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/i915_reg.h       |   4 +
 drivers/gpu/drm/i915/intel_ddi.c      |  29 +++++
 drivers/gpu/drm/i915/intel_drv.h      |  14 ++
 drivers/gpu/drm/i915/intel_hdmi.c     | 100 +++++++++++++++
 include/drm/drm_connector.h           |  52 ++++++++
 include/drm/drm_edid.h                |   6 +-
 include/drm/drm_scdc_helper.h         | 159 +++++++++++++++++++++++
 include/linux/hdmi.h                  |   1 +
 12 files changed, 672 insertions(+), 2 deletions(-)
 create mode 100644 drivers/gpu/drm/drm_scdc_helper.c
 create mode 100644 include/drm/drm_scdc_helper.h
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#1 lore raw

PATCH v5 1/6 drm: Add SCDC helpers

From: Thierry Reding <[email protected]>

SCDC is a mechanism defined in the HDMI 2.0 specification that allows the source and sink devices to communicate.

This commit introduces helpers to access the SCDC and provides the symbolic names for the various registers defined in the specification.

V2: Rebase.
V3: Added R-B from Jose.
V4: Rebase
V5: Addressed review comments from Ville
- Handle the I2c return values in a better way (dp_dual_mode)
- Make the macros for SCDC Major/Minor more readable, by adding a 'GET' in the macro names

---
 Documentation/gpu/drm-kms-helpers.rst |  12 ++++
 drivers/gpu/drm/Makefile              |   3 +-
 drivers/gpu/drm/drm_scdc_helper.c     | 123 +++++++++++++++++++++++++++++++
 include/drm/drm_scdc_helper.h         | 132 ++++++++++++++++++++++++++++++++++
 4 files changed, 269 insertions(+), 1 deletion(-)
 create mode 100644 drivers/gpu/drm/drm_scdc_helper.c
 create mode 100644 include/drm/drm_scdc_helper.h
Documentation/gpu/drm-kms-helpers.rst +12 -0
index 03040aa..7592756 100644
@@ -217,6 +217,18 @@ EDID Helper Functions Reference
 .. kernel-doc:: drivers/gpu/drm/drm_edid.c
    :export:
 
+SCDC Helper Functions Reference
+===============================
+
+.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c
+   :doc: scdc helpers
+
+.. kernel-doc:: include/drm/drm_scdc_helper.h
+   :internal:
+
+.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c
+   :export:
+
 Rectangle Utilities Reference
 =============================
 
drivers/gpu/drm/Makefile +2 -1
index 3ee9579..da5b08c 100644
@@ -31,7 +31,8 @@ drm-$(CONFIG_DEBUG_FS) += drm_debugfs.o drm_debugfs_crc.o
 drm_kms_helper-y := drm_crtc_helper.o drm_dp_helper.o drm_probe_helper.o \
 		drm_plane_helper.o drm_dp_mst_topology.o drm_atomic_helper.o \
 		drm_kms_helper_common.o drm_dp_dual_mode_helper.o \
-		drm_simple_kms_helper.o drm_modeset_helper.o
+		drm_simple_kms_helper.o drm_modeset_helper.o \
+		drm_scdc_helper.o
 
 drm_kms_helper-$(CONFIG_DRM_LOAD_EDID_FIRMWARE) += drm_edid_load.o
 drm_kms_helper-$(CONFIG_DRM_FBDEV_EMULATION) += drm_fb_helper.o
drivers/gpu/drm/drm_scdc_helper.c new file +123 -0

123 lines not on this page · raw message

include/drm/drm_scdc_helper.h new file +132 -0

132 lines not on this page · raw message

Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#2 lore raw

PATCH v5 2/6 drm/edid: check for HF-VSDB block

In reply to Shashank Sharma

From: Thierry Reding <[email protected]>

This patch implements a small function that finds if a given CEA db is hdmi-forum vendor specific data block or not.

V2: Rebase.
V3: Added R-B from Jose.
V4: Rebase
V5: Rebase

---
 drivers/gpu/drm/drm_edid.c | 15 +++++++++++++++
 include/linux/hdmi.h       |  1 +
 2 files changed, 16 insertions(+)
drivers/gpu/drm/drm_edid.c +15 -0
index e1743ab..055b511 100644
@@ -3248,6 +3248,21 @@ static bool cea_db_is_hdmi_vsdb(const u8 *db)
 	return hdmi_id == HDMI_IEEE_OUI;
 }
 
+static bool cea_db_is_hdmi_forum_vsdb(const u8 *db)
+{
+	unsigned int oui;
+
+	if (cea_db_tag(db) != VENDOR_BLOCK)
+		return false;
+
+	if (cea_db_payload_len(db) < 7)
+		return false;
+
+	oui = db[3] << 16 | db[2] << 8 | db[1];
+
+	return oui == HDMI_FORUM_IEEE_OUI;
+}
+
 #define for_each_cea_db(cea, i, start, end) \
 	for ((i) = (start); (i) < (end) && (i) + cea_db_payload_len(&(cea)[(i)]) < (end); (i) += cea_db_payload_len(&(cea)[(i)]) + 1)
 
include/linux/hdmi.h +1 -0
index edbb4fc..d271ff2 100644
@@ -35,6 +35,7 @@ enum hdmi_infoframe_type {
 };
 
 #define HDMI_IEEE_OUI 0x000c03
+#define HDMI_FORUM_IEEE_OUI 0xc45dd8
 #define HDMI_INFOFRAME_HEADER_SIZE  4
 #define HDMI_AVI_INFOFRAME_SIZE    13
 #define HDMI_SPD_INFOFRAME_SIZE    25
Signature · 6 lines
1.9.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#3 lore raw

PATCH v5 3/6 drm/edid: detect SCDC support in HF-VSDB

In reply to Shashank Sharma

This patch does following:
- Adds a new structure (drm_hdmi_info) in drm_display_info. This structure will be used to save and indicate if sink supports advanced HDMI 2.0 features
- Adds another structure drm_scdc within drm_hdmi_info, to reflect scdc support and capabilities in connected HDMI 2.0 sink.
- Checks the HF-VSDB block for presence of SCDC, and marks it in scdc structure
- If SCDC is present, checks if sink is capable of generating SCDC read request, and marks it in scdc structure.

V2: Addressed review comments
Thierry:
- Fix typos in commit message and make abbreviation consistent across the commit message.
- Change structure object name from hdmi_info -> hdmi
- Fix typos and abbreviations in description of structure drm_hdmi_info end the description with a full stop.
- Create a structure drm_scdc, and keep all information related to SCDC register set (supported, read request supported) etc in it.

Ville:
- Change rr -> read_request
- Call drm_detect_scrambling function drm_parse_hf_vsdb so that all of HF-VSDB parsing can be kept in same function, in incremental patches.

V3: Rebase.
V4: Rebase.
V5: Rebase.

---
 drivers/gpu/drm/drm_edid.c  | 14 ++++++++++++++
 include/drm/drm_connector.h | 33 +++++++++++++++++++++++++++++++++
 2 files changed, 47 insertions(+)
drivers/gpu/drm/drm_edid.c +14 -0
index 055b511..0881108 100644
@@ -3814,6 +3814,18 @@ enum hdmi_quantization_range
 }
 EXPORT_SYMBOL(drm_default_rgb_quant_range);
 
+static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
+				 const u8 *hf_vsdb)
+{
+	struct drm_hdmi_info *hdmi = &connector->display_info.hdmi;
+
+	if (hf_vsdb[6] & 0x80) {
+		hdmi->scdc.supported = true;
+		if (hf_vsdb[6] & 0x40)
+			hdmi->scdc.read_request = true;
+	}
+}
+
 static void drm_parse_hdmi_deep_color_info(struct drm_connector *connector,
 					   const u8 *hdmi)
 {
@@ -3928,6 +3940,8 @@ static void drm_parse_cea_ext(struct drm_connector *connector,
 
 		if (cea_db_is_hdmi_vsdb(db))
 			drm_parse_hdmi_vsdb_video(connector, db);
+		if (cea_db_is_hdmi_forum_vsdb(db))
+			drm_parse_hdmi_forum_vsdb(connector, db);
 	}
 }
 
include/drm/drm_connector.h +33 -0
index e5e1edd..6d5304e 100644
@@ -87,6 +87,34 @@ enum subpixel_order {
 	SubPixelVerticalRGB,
 	SubPixelVerticalBGR,
 	SubPixelNone,
+
+};
+
+/*
+ * struct drm_scdc - Information about scdc capabilities of a HDMI 2.0 sink
+ *
+ * Provides SCDC register support and capabilities related information on a
+ * HDMI 2.0 sink. In case of a HDMI 1.4 sink, all parameter must be 0.
+ */
+struct drm_scdc {
+	/**
+	 * @supported: status control & data channel present.
+	 */
+	bool supported;
+	/**
+	 * @read_request: sink is capable of generating scdc read request.
+	 */
+	bool read_request;
+};
+
+/**
+ * struct drm_hdmi_info - runtime information about the connected HDMI sink
+ *
+ * Describes if a given display supports advanced HDMI 2.0 features.
+ * This information is available in CEA-861-F extension blocks (like HF-VSDB).
+ */
+struct drm_hdmi_info {
+	struct drm_scdc scdc;
 };
 
 /**
@@ -188,6 +216,11 @@ struct drm_display_info {
 	 * @cea_rev: CEA revision of the HDMI sink.
 	 */
 	u8 cea_rev;
+
+	/**
+	 * @hdmi: advance features of a HDMI sink.
+	 */
+	struct drm_hdmi_info hdmi;
 };
 
 int drm_display_info_set_bus_formats(struct drm_display_info *info,
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#4 lore raw

PATCH v5 4/6 drm/edid: detect SCDC support in HF-VSDB

In reply to Shashank Sharma

This patch does following:
- Adds a new structure (drm_hdmi_info) in drm_display_info. This structure will be used to save and indicate if sink supports advanced HDMI 2.0 features
- Adds another structure drm_scdc within drm_hdmi_info, to reflect scdc support and capabilities in connected HDMI 2.0 sink.
- Checks the HF-VSDB block for presence of SCDC, and marks it in scdc structure
- If SCDC is present, checks if sink is capable of generating SCDC read request, and marks it in scdc structure.

V2: Addressed review comments
Thierry:
- Fix typos in commit message and make abbreviation consistent across the commit message.
- Change structure object name from hdmi_info -> hdmi
- Fix typos and abbreviations in description of structure drm_hdmi_info end the description with a full stop.
- Create a structure drm_scdc, and keep all information related to SCDC register set (supported, read request supported) etc in it.

Ville:
- Change rr -> read_request
- Call drm_detect_scrambling function drm_parse_hf_vsdb so that all of HF-VSDB parsing can be kept in same function, in incremental patches.

V3: Rebase.
V4: Rebase.
V5: Rebase.

---
 drivers/gpu/drm/drm_edid.c        |  33 +++++++++++-
 drivers/gpu/drm/drm_scdc_helper.c | 111 ++++++++++++++++++++++++++++++++++++++
 include/drm/drm_connector.h       |  19 +++++++
 include/drm/drm_edid.h            |   6 ++-
 include/drm/drm_scdc_helper.h     |  27 ++++++++++
 5 files changed, 194 insertions(+), 2 deletions(-)
drivers/gpu/drm/drm_edid.c +32 -1
index 0881108..e84c5ab 100644
@@ -37,6 +37,7 @@
 #include <drm/drm_edid.h>
 #include <drm/drm_encoder.h>
 #include <drm/drm_displayid.h>
+#include <drm/drm_scdc_helper.h>
 
 #include "drm_crtc_internal.h"
 
@@ -3817,13 +3818,43 @@ enum hdmi_quantization_range
 static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
 				 const u8 *hf_vsdb)
 {
-	struct drm_hdmi_info *hdmi = &connector->display_info.hdmi;
+	struct drm_display_info *display = &connector->display_info;
+	struct drm_hdmi_info *hdmi = &display->hdmi;
 
 	if (hf_vsdb[6] & 0x80) {
 		hdmi->scdc.supported = true;
 		if (hf_vsdb[6] & 0x40)
 			hdmi->scdc.read_request = true;
 	}
+
+	/*
+	 * All HDMI 2.0 monitors must support scrambling at rates > 340 MHz.
+	 * And as per the spec, three factors confirm this:
+	 * * Availability of a HF-VSDB block in EDID (check)
+	 * * Non zero Max_TMDS_Char_Rate filed in HF-VSDB (let's check)
+	 * * SCDC support available (let's check)
+	 * Lets check it out.
+	 */
+
+	if (hf_vsdb[5]) {
+		/* max clock is 5000 KHz times block value */
+		u32 max_tmds_clock = hf_vsdb[5] * 5000;
+		struct drm_scdc *scdc = &hdmi->scdc;
+
+		if (max_tmds_clock > 340000) {
+			display->max_tmds_clock = max_tmds_clock;
+			DRM_DEBUG_KMS("HF-VSDB: max TMDS clock %d kHz\n",
+				display->max_tmds_clock);
+		}
+
+		if (scdc->supported) {
+			scdc->scrambling.supported = true;
+
+			/* Few sinks support scrambling for cloks < 340M */
+			if ((hf_vsdb[6] & 0x8))
+				scdc->scrambling.low_rates = true;
+		}
+	}
 }
 
 static void drm_parse_hdmi_deep_color_info(struct drm_connector *connector,
drivers/gpu/drm/drm_scdc_helper.c +111 -0

122 lines not on this page · raw message

include/drm/drm_connector.h +19 -0
index 6d5304e..78618308 100644
@@ -90,6 +90,20 @@ enum subpixel_order {
 
 };
 
+/**
+ * struct drm_scrambling: sink's scrambling support.
+ */
+struct drm_scrambling {
+	/**
+	 * @supported: scrambling supported for rates > 340 Mhz.
+	 */
+	bool supported;
+	/**
+	 * @low_rates: scrambling supported for rates <= 340 Mhz.
+	 */
+	bool low_rates;
+};
+
 /*
  * struct drm_scdc - Information about scdc capabilities of a HDMI 2.0 sink
  *
@@ -105,8 +119,13 @@ struct drm_scdc {
 	 * @read_request: sink is capable of generating scdc read request.
 	 */
 	bool read_request;
+	/**
+	 * @scrambling: sink's scrambling capabilities
+	 */
+	struct drm_scrambling scrambling;
 };
 
+
 /**
  * struct drm_hdmi_info - runtime information about the connected HDMI sink
  *
include/drm/drm_edid.h +5 -1
index 3ead84d..f4a91e0 100644
@@ -476,5 +476,9 @@ void drm_edid_get_monitor_name(struct edid *edid, char *name,
 struct drm_display_mode *drm_mode_find_dmt(struct drm_device *dev,
 					   int hsize, int vsize, int fresh,
 					   bool rb);
-
+bool drm_enable_scrambling(struct drm_connector *connector,
+				struct i2c_adapter *adapter, bool force);
+bool drm_disable_scrambling(struct drm_connector *connector,
+				struct i2c_adapter *adapter, bool force);
+bool drm_check_scrambling_status(struct i2c_adapter *adapter);
 #endif /* __DRM_EDID_H__ */
include/drm/drm_scdc_helper.h +27 -0
index 9c52deb..ab6bcfb 100644
@@ -129,4 +129,31 @@ static inline int drm_scdc_writeb(struct i2c_adapter *adapter, u8 offset,
 	return drm_scdc_write(adapter, offset, &value, sizeof(value));
 }
 
+/**
+ * drm_scdc_set_scrambling - enable scrambling
+ * @adapter: I2C adapter for DDC channel
+ * @enable: bool to indicate if scrambling is to be enabled/disabled
+ *
+ * Writes the TMDS config register over SCDC channel, and:
+ * enables scrambling when enable = 1
+ * disables scrambling when enable = 0
+ *
+ * Returns:
+ * True if scrambling is set/reset successfully, false otherwise.
+ */
+bool drm_scdc_set_scrambling(struct i2c_adapter *adapter, bool enable);
+
+/**
+ * drm_scdc_set_high_tmds_clock_ratio - set TMDS clock ratio
+ * @adapter: I2C adapter for DDC channel
+ * @set: ret or reset the high clock ratio
+ *
+ * Writes to the TMDS config register over SCDC channel, and:
+ * sets TMDS clock ratio to 1/40 when set = 1
+ * sets TMDS clock ratio to 1/10 when set = 0
+ *
+ * Returns:
+ * True if write is successful, false otherwise.
+ */
+bool drm_scdc_set_high_tmds_clock_ratio(struct i2c_adapter *adapter, bool set);
 #endif
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#5 lore raw

Re: [PATCH v5 4/6] drm/edid: detect SCDC support in HF-VSDB

Quoted 181 lines · Shashank Sharma

This patch does following:
- Adds a new structure (drm_hdmi_info) in drm_display_info. This structure will be used to save and indicate if sink supports advanced HDMI 2.0 features
- Adds another structure drm_scdc within drm_hdmi_info, to reflect scdc support and capabilities in connected HDMI 2.0 sink.
- Checks the HF-VSDB block for presence of SCDC, and marks it in scdc structure
- If SCDC is present, checks if sink is capable of generating SCDC read request, and marks it in scdc structure.

V2: Addressed review comments
Thierry:
- Fix typos in commit message and make abbreviation consistent across the commit message.
- Change structure object name from hdmi_info -> hdmi
- Fix typos and abbreviations in description of structure drm_hdmi_info end the description with a full stop.
- Create a structure drm_scdc, and keep all information related to SCDC register set (supported, read request supported) etc in it.

Ville:
- Change rr -> read_request
- Call drm_detect_scrambling function drm_parse_hf_vsdb so that all of HF-VSDB parsing can be kept in same function, in incremental patches.

V3: Rebase.
V4: Rebase.
V5: Rebase.

---
 drivers/gpu/drm/drm_edid.c        |  33 +++++++++++-
 drivers/gpu/drm/drm_scdc_helper.c | 111 ++++++++++++++++++++++++++++++++++++++
 include/drm/drm_connector.h       |  19 +++++++
 include/drm/drm_edid.h            |   6 ++-
 include/drm/drm_scdc_helper.h     |  27 ++++++++++
 5 files changed, 194 insertions(+), 2 deletions(-)
drivers/gpu/drm/drm_edid.c +32 -1
index 0881108..e84c5ab 100644
@@ -37,6 +37,7 @@
 #include <drm/drm_edid.h>
 #include <drm/drm_encoder.h>
 #include <drm/drm_displayid.h>
+#include <drm/drm_scdc_helper.h>
 
 #include "drm_crtc_internal.h"
 
@@ -3817,13 +3818,43 @@ enum hdmi_quantization_range
 static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
 				 const u8 *hf_vsdb)
 {
-	struct drm_hdmi_info *hdmi = &connector->display_info.hdmi;
+	struct drm_display_info *display = &connector->display_info;
+	struct drm_hdmi_info *hdmi = &display->hdmi;
 
 	if (hf_vsdb[6] & 0x80) {
 		hdmi->scdc.supported = true;
 		if (hf_vsdb[6] & 0x40)
 			hdmi->scdc.read_request = true;
 	}
+
+	/*
+	 * All HDMI 2.0 monitors must support scrambling at rates > 340 MHz.
+	 * And as per the spec, three factors confirm this:
+	 * * Availability of a HF-VSDB block in EDID (check)
+	 * * Non zero Max_TMDS_Char_Rate filed in HF-VSDB (let's check)
+	 * * SCDC support available (let's check)
+	 * Lets check it out.
+	 */
+
+	if (hf_vsdb[5]) {
+		/* max clock is 5000 KHz times block value */
+		u32 max_tmds_clock = hf_vsdb[5] * 5000;
+		struct drm_scdc *scdc = &hdmi->scdc;
+
+		if (max_tmds_clock > 340000) {
+			display->max_tmds_clock = max_tmds_clock;
+			DRM_DEBUG_KMS("HF-VSDB: max TMDS clock %d kHz\n",
+				display->max_tmds_clock);
+		}
+
+		if (scdc->supported) {
+			scdc->scrambling.supported = true;
+
+			/* Few sinks support scrambling for cloks < 340M */
+			if ((hf_vsdb[6] & 0x8))
+				scdc->scrambling.low_rates = true;
+		}
+	}
 }
 
 static void drm_parse_hdmi_deep_color_info(struct drm_connector *connector,
drivers/gpu/drm/drm_scdc_helper.c +66 -0
index c2dd33f..180a7cd 100644
@@ -22,8 +22,10 @@
  */
 
 #include <linux/slab.h>
+#include <linux/delay.h>
 
 #include <drm/drm_scdc_helper.h>
+#include <drm/drmP.h>
 
 /**
  * DOC: scdc helpers
@@ -121,3 +123,112 @@ ssize_t drm_scdc_write(struct i2c_adapter *adapter, u8 offset,
 	return 0;
 }
 EXPORT_SYMBOL(drm_scdc_write);
+
+/**
+ * drm_scdc_check_scrambling_status - what is status of scrambling?
+ * @adapter: I2C adapter for DDC channel
+ *
+ * Reads the scrambler status over SCDC, and checks the
+ * scrambling status.
+ *
+ * Returns:
+ * True if the scrambling is enabled, false otherwise.
+ */
+
+bool drm_scdc_get_scrambling_status(struct i2c_adapter *adapter)
+{
+	u8 status;
+	int ret;
+
+	ret = drm_scdc_readb(adapter, SCDC_SCRAMBLER_STATUS, &status);
+	if (ret < 0) {
+		DRM_ERROR("Failed to read scrambling status, error %d\n", ret);
+		return false;
+	}
+
+	return status & SCDC_SCRAMBLING_STATUS;
+}
+EXPORT_SYMBOL(drm_scdc_get_scrambling_status);
+
+/**
+ * drm_scdc_set_scrambling - enable scrambling
+ * @adapter: I2C adapter for DDC channel
+ * @enable: bool to indicate if scrambling is to be enabled/disabled
+ *
+ * Writes the TMDS config register over SCDC channel, and:
+ * enables scrambling when enable = 1
+ * disables scrambling when enable = 0
+ *
+ * Returns:
+ * True if scrambling is set/reset successfully, false otherwise.
+ */
+
+bool drm_scdc_set_scrambling(struct i2c_adapter *adapter, bool enable)
+{
+	u8 config;
+	int ret;
+
+	ret = drm_scdc_readb(adapter, SCDC_TMDS_CONFIG, &config);
+	if (ret < 0) {
+		DRM_ERROR("Failed to read tmds config, err=%d\n", ret);
+		return false;
+	}
+
+	if (enable)
+		config |= SCDC_SCRAMBLING_ENABLE;
+	else
+		config &= ~SCDC_SCRAMBLING_ENABLE;
+
+	ret = drm_scdc_writeb(adapter, SCDC_TMDS_CONFIG, config);
+	if (ret < 0) {
+		DRM_ERROR("Failed to enable scrambling, error %d\n", ret);
+		return false;
+	}
+
+	return true;
+}

drivers/gpu/drm/drm_scdc_helper.c ssize_t drm_scdc_write(struct i2c_adapter *adapter, u8 offset, · line 199

Quoted 10 lines
drivers/gpu/drm/drm_scdc_helper.c +10 -0
+EXPORT_SYMBOL(drm_scdc_set_scrambling);
+
+/**
+ * drm_scdc_set_high_tmds_clock_ratio - set TMDS clock ratio
+ * @adapter: I2C adapter for DDC channel
+ * @set: ret or reset the high clock ratio
+ *
+ * Writes to the TMDS config register over SCDC channel, and:
+ * sets TMDS clock ratio to 1/40 when set = 1
+ * sets TMDS clock ratio to 1/10 when set = 0

The 1/10 and 1/40 ratios confuse me a little since we never really deal with the bitrate in the driver. Instead we always deal with either pixel clock, character clock or TMDS clock (well prior to this TMDS clock == character clock). So the factor 10 never enters the picture elsewhere. So I would prefer to specify these in those terms as well.

An enum for the ratios might also help in making this a bit less cryptic.

Quoted 79 lines
drivers/gpu/drm/drm_scdc_helper.c +35 -0
+ *
+ * Returns:
+ * True if write is successful, false otherwise.
+ */
+bool drm_scdc_set_high_tmds_clock_ratio(struct i2c_adapter *adapter, bool set)
+{
+	u8 config;
+	int ret;
+
+	ret = drm_scdc_readb(adapter, SCDC_TMDS_CONFIG, &config);
+	if (ret < 0) {
+		DRM_ERROR("Failed to read tmds config, err=%d\n", ret);
+		return false;
+	}
+
+	if (set)
+		config |= SCDC_TMDS_BIT_CLOCK_RATIO_BY_40;
+	else
+		config &= ~SCDC_TMDS_BIT_CLOCK_RATIO_BY_40;
+
+	ret = drm_scdc_writeb(adapter, SCDC_TMDS_CONFIG, config);
+	if (ret < 0) {
+		DRM_ERROR("Failed to set TMDS clock ratio, error %d\n", ret);
+		return false;
+	}
+
+	/*
+	 * The spec says that a source should wait minimum 1ms and maximum
+	 * 100ms after writing the TMDS config for clock ratio. Lets allow a
+	 * wait of upto 2ms here.
+	 */
+	usleep_range(1000, 2000);
+	return true;
+}
+EXPORT_SYMBOL(drm_scdc_set_high_tmds_clock_ratio);
include/drm/drm_connector.h +19 -0
index 6d5304e..78618308 100644
@@ -90,6 +90,20 @@ enum subpixel_order {
 
 };
 
+/**
+ * struct drm_scrambling: sink's scrambling support.
+ */
+struct drm_scrambling {
+	/**
+	 * @supported: scrambling supported for rates > 340 Mhz.
+	 */
+	bool supported;
+	/**
+	 * @low_rates: scrambling supported for rates <= 340 Mhz.
+	 */
+	bool low_rates;
+};
+
 /*
  * struct drm_scdc - Information about scdc capabilities of a HDMI 2.0 sink
  *
@@ -105,8 +119,13 @@ struct drm_scdc {
 	 * @read_request: sink is capable of generating scdc read request.
 	 */
 	bool read_request;
+	/**
+	 * @scrambling: sink's scrambling capabilities
+	 */
+	struct drm_scrambling scrambling;
 };
 
+
 /**
  * struct drm_hdmi_info - runtime information about the connected HDMI sink
  *
include/drm/drm_edid.h +0 -0
index 3ead84d..f4a91e0 100644

include/drm/drm_edid.h void drm_edid_get_monitor_name(struct edid *edid, char *name, · line 483

Quoted 9 lines
include/drm/drm_edid.h +5 -1
@@ -476,5 +476,9 @@ void drm_edid_get_monitor_name(struct edid *edid, char *name,
 struct drm_display_mode *drm_mode_find_dmt(struct drm_device *dev,
 					   int hsize, int vsize, int fresh,
 					   bool rb);
-
+bool drm_enable_scrambling(struct drm_connector *connector,
+				struct i2c_adapter *adapter, bool force);
+bool drm_disable_scrambling(struct drm_connector *connector,
+				struct i2c_adapter *adapter, bool force);
+bool drm_check_scrambling_status(struct i2c_adapter *adapter);

Old leftovers?

Quoted 39 lines
include/drm/drm_edid.h +0 -0
 #endif /* __DRM_EDID_H__ */
include/drm/drm_scdc_helper.h +27 -0
index 9c52deb..ab6bcfb 100644
@@ -129,4 +129,31 @@ static inline int drm_scdc_writeb(struct i2c_adapter *adapter, u8 offset,
 	return drm_scdc_write(adapter, offset, &value, sizeof(value));
 }
 
+/**
+ * drm_scdc_set_scrambling - enable scrambling
+ * @adapter: I2C adapter for DDC channel
+ * @enable: bool to indicate if scrambling is to be enabled/disabled
+ *
+ * Writes the TMDS config register over SCDC channel, and:
+ * enables scrambling when enable = 1
+ * disables scrambling when enable = 0
+ *
+ * Returns:
+ * True if scrambling is set/reset successfully, false otherwise.
+ */
+bool drm_scdc_set_scrambling(struct i2c_adapter *adapter, bool enable);
+
+/**
+ * drm_scdc_set_high_tmds_clock_ratio - set TMDS clock ratio
+ * @adapter: I2C adapter for DDC channel
+ * @set: ret or reset the high clock ratio
+ *
+ * Writes to the TMDS config register over SCDC channel, and:
+ * sets TMDS clock ratio to 1/40 when set = 1
+ * sets TMDS clock ratio to 1/10 when set = 0
+ *
+ * Returns:
+ * True if write is successful, false otherwise.
+ */
+bool drm_scdc_set_high_tmds_clock_ratio(struct i2c_adapter *adapter, bool set);
 #endif
Signature · 1 line
1.9.1
Signature · 6 lines
Ville Syrjälä
Intel OTC
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#6 lore raw

Re: [PATCH v5 4/6] drm/edid: detect SCDC support in HF-VSDB

Regards

Shashank

Quoted 189 lines · Ville Syrjälä
Quoted 188 lines · Shashank Sharma

This patch does following:
- Adds a new structure (drm_hdmi_info) in drm_display_info. This structure will be used to save and indicate if sink supports advanced HDMI 2.0 features
- Adds another structure drm_scdc within drm_hdmi_info, to reflect scdc support and capabilities in connected HDMI 2.0 sink.
- Checks the HF-VSDB block for presence of SCDC, and marks it in scdc structure
- If SCDC is present, checks if sink is capable of generating SCDC read request, and marks it in scdc structure.

V2: Addressed review comments
Thierry:
- Fix typos in commit message and make abbreviation consistent across the commit message.
- Change structure object name from hdmi_info -> hdmi
- Fix typos and abbreviations in description of structure drm_hdmi_info end the description with a full stop.
- Create a structure drm_scdc, and keep all information related to SCDC register set (supported, read request supported) etc in it.

Ville:
- Change rr -> read_request
- Call drm_detect_scrambling function drm_parse_hf_vsdb so that all of HF-VSDB parsing can be kept in same function, in incremental patches.

V3: Rebase.
V4: Rebase.
V5: Rebase.

---
  drivers/gpu/drm/drm_edid.c        |  33 +++++++++++-
  drivers/gpu/drm/drm_scdc_helper.c | 111 ++++++++++++++++++++++++++++++++++++++
  include/drm/drm_connector.h       |  19 +++++++
  include/drm/drm_edid.h            |   6 ++-
  include/drm/drm_scdc_helper.h     |  27 ++++++++++
  5 files changed, 194 insertions(+), 2 deletions(-)
drivers/gpu/drm/drm_edid.c +32 -1
index 0881108..e84c5ab 100644
@@ -37,6 +37,7 @@
  #include <drm/drm_edid.h>
  #include <drm/drm_encoder.h>
  #include <drm/drm_displayid.h>
+#include <drm/drm_scdc_helper.h>
 
  #include "drm_crtc_internal.h"
 
@@ -3817,13 +3818,43 @@ enum hdmi_quantization_range
  static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
  				 const u8 *hf_vsdb)
  {
-	struct drm_hdmi_info *hdmi = &connector->display_info.hdmi;
+	struct drm_display_info *display = &connector->display_info;
+	struct drm_hdmi_info *hdmi = &display->hdmi;
 
  	if (hf_vsdb[6] & 0x80) {
  		hdmi->scdc.supported = true;
  		if (hf_vsdb[6] & 0x40)
  			hdmi->scdc.read_request = true;
  	}
+
+	/*
+	 * All HDMI 2.0 monitors must support scrambling at rates > 340 MHz.
+	 * And as per the spec, three factors confirm this:
+	 * * Availability of a HF-VSDB block in EDID (check)
+	 * * Non zero Max_TMDS_Char_Rate filed in HF-VSDB (let's check)
+	 * * SCDC support available (let's check)
+	 * Lets check it out.
+	 */
+
+	if (hf_vsdb[5]) {
+		/* max clock is 5000 KHz times block value */
+		u32 max_tmds_clock = hf_vsdb[5] * 5000;
+		struct drm_scdc *scdc = &hdmi->scdc;
+
+		if (max_tmds_clock > 340000) {
+			display->max_tmds_clock = max_tmds_clock;
+			DRM_DEBUG_KMS("HF-VSDB: max TMDS clock %d kHz\n",
+				display->max_tmds_clock);
+		}
+
+		if (scdc->supported) {
+			scdc->scrambling.supported = true;
+
+			/* Few sinks support scrambling for cloks < 340M */
+			if ((hf_vsdb[6] & 0x8))
+				scdc->scrambling.low_rates = true;
+		}
+	}
  }
 
  static void drm_parse_hdmi_deep_color_info(struct drm_connector *connector,
drivers/gpu/drm/drm_scdc_helper.c +73 -0
index c2dd33f..180a7cd 100644
@@ -22,8 +22,10 @@
   */
 
  #include <linux/slab.h>
+#include <linux/delay.h>
 
  #include <drm/drm_scdc_helper.h>
+#include <drm/drmP.h>
 
  /**
   * DOC: scdc helpers
@@ -121,3 +123,112 @@ ssize_t drm_scdc_write(struct i2c_adapter *adapter, u8 offset,
  	return 0;
  }
  EXPORT_SYMBOL(drm_scdc_write);
+
+/**
+ * drm_scdc_check_scrambling_status - what is status of scrambling?
+ * @adapter: I2C adapter for DDC channel
+ *
+ * Reads the scrambler status over SCDC, and checks the
+ * scrambling status.
+ *
+ * Returns:
+ * True if the scrambling is enabled, false otherwise.
+ */
+
+bool drm_scdc_get_scrambling_status(struct i2c_adapter *adapter)
+{
+	u8 status;
+	int ret;
+
+	ret = drm_scdc_readb(adapter, SCDC_SCRAMBLER_STATUS, &status);
+	if (ret < 0) {
+		DRM_ERROR("Failed to read scrambling status, error %d\n", ret);
+		return false;
+	}
+
+	return status & SCDC_SCRAMBLING_STATUS;
+}
+EXPORT_SYMBOL(drm_scdc_get_scrambling_status);
+
+/**
+ * drm_scdc_set_scrambling - enable scrambling
+ * @adapter: I2C adapter for DDC channel
+ * @enable: bool to indicate if scrambling is to be enabled/disabled
+ *
+ * Writes the TMDS config register over SCDC channel, and:
+ * enables scrambling when enable = 1
+ * disables scrambling when enable = 0
+ *
+ * Returns:
+ * True if scrambling is set/reset successfully, false otherwise.
+ */
+
+bool drm_scdc_set_scrambling(struct i2c_adapter *adapter, bool enable)
+{
+	u8 config;
+	int ret;
+
+	ret = drm_scdc_readb(adapter, SCDC_TMDS_CONFIG, &config);
+	if (ret < 0) {
+		DRM_ERROR("Failed to read tmds config, err=%d\n", ret);
+		return false;
+	}
+
+	if (enable)
+		config |= SCDC_SCRAMBLING_ENABLE;
+	else
+		config &= ~SCDC_SCRAMBLING_ENABLE;
+
+	ret = drm_scdc_writeb(adapter, SCDC_TMDS_CONFIG, config);
+	if (ret < 0) {
+		DRM_ERROR("Failed to enable scrambling, error %d\n", ret);
+		return false;
+	}
+
+	return true;
+}
+EXPORT_SYMBOL(drm_scdc_set_scrambling);
+
+/**
+ * drm_scdc_set_high_tmds_clock_ratio - set TMDS clock ratio
+ * @adapter: I2C adapter for DDC channel
+ * @set: ret or reset the high clock ratio
+ *
Quoted 8 lines

drivers/gpu/drm/drm_scdc_helper.c ssize_t drm_scdc_write(struct i2c_adapter *adapter, u8 offset, · line 199

Quoted 3 lines
drivers/gpu/drm/drm_scdc_helper.c +3 -0
+ * Writes to the TMDS config register over SCDC channel, and:
+ * sets TMDS clock ratio to 1/40 when set = 1
+ * sets TMDS clock ratio to 1/10 when set = 0

The 1/10 and 1/40 ratios confuse me a little since we never really deal with the bitrate in the driver. Instead we always deal with either pixel clock, character clock or TMDS clock (well prior to this TMDS clock == character clock). So the factor 10 never enters the picture elsewhere. So I would prefer to specify these in those terms as well.

Ok, I will add comments for pixel clock as well

Quoted 2 lines

An enum for the ratios might also help in making this a bit less cryptic.

Humm, not sure how helpful will be an enum, as thats only used in case of pixelclock>340 asso, only two entries 1/40 and 1/10, but let me see if I can do that.

Quoted 81 lines
Quoted 81 lines
drivers/gpu/drm/drm_scdc_helper.c +35 -0
+ *
+ * Returns:
+ * True if write is successful, false otherwise.
+ */
+bool drm_scdc_set_high_tmds_clock_ratio(struct i2c_adapter *adapter, bool set)
+{
+	u8 config;
+	int ret;
+
+	ret = drm_scdc_readb(adapter, SCDC_TMDS_CONFIG, &config);
+	if (ret < 0) {
+		DRM_ERROR("Failed to read tmds config, err=%d\n", ret);
+		return false;
+	}
+
+	if (set)
+		config |= SCDC_TMDS_BIT_CLOCK_RATIO_BY_40;
+	else
+		config &= ~SCDC_TMDS_BIT_CLOCK_RATIO_BY_40;
+
+	ret = drm_scdc_writeb(adapter, SCDC_TMDS_CONFIG, config);
+	if (ret < 0) {
+		DRM_ERROR("Failed to set TMDS clock ratio, error %d\n", ret);
+		return false;
+	}
+
+	/*
+	 * The spec says that a source should wait minimum 1ms and maximum
+	 * 100ms after writing the TMDS config for clock ratio. Lets allow a
+	 * wait of upto 2ms here.
+	 */
+	usleep_range(1000, 2000);
+	return true;
+}
+EXPORT_SYMBOL(drm_scdc_set_high_tmds_clock_ratio);
include/drm/drm_connector.h +19 -0
index 6d5304e..78618308 100644
@@ -90,6 +90,20 @@ enum subpixel_order {
 
  };
 
+/**
+ * struct drm_scrambling: sink's scrambling support.
+ */
+struct drm_scrambling {
+	/**
+	 * @supported: scrambling supported for rates > 340 Mhz.
+	 */
+	bool supported;
+	/**
+	 * @low_rates: scrambling supported for rates <= 340 Mhz.
+	 */
+	bool low_rates;
+};
+
  /*
   * struct drm_scdc - Information about scdc capabilities of a HDMI 2.0 sink
   *
@@ -105,8 +119,13 @@ struct drm_scdc {
  	 * @read_request: sink is capable of generating scdc read request.
  	 */
  	bool read_request;
+	/**
+	 * @scrambling: sink's scrambling capabilities
+	 */
+	struct drm_scrambling scrambling;
  };
 
+
  /**
   * struct drm_hdmi_info - runtime information about the connected HDMI sink
   *
include/drm/drm_edid.h +0 -0
index 3ead84d..f4a91e0 100644
@@ -476,5 +476,9 @@ void drm_edid_get_monitor_name(struct edid *edid, char *name,
  struct drm_display_mode *drm_mode_find_dmt(struct drm_device *dev,
  					   int hsize, int vsize, int fresh,
Quoted 8 lines

include/drm/drm_edid.h void drm_edid_get_monitor_name(struct edid *edid, char *name, · line 483

Quoted 7 lines
include/drm/drm_edid.h +5 -1
  					   bool rb);
-
+bool drm_enable_scrambling(struct drm_connector *connector,
+				struct i2c_adapter *adapter, bool force);
+bool drm_disable_scrambling(struct drm_connector *connector,
+				struct i2c_adapter *adapter, bool force);
+bool drm_check_scrambling_status(struct i2c_adapter *adapter);

Old leftovers?

Oops, my bad.

Quoted 31 lines
Quoted 31 lines
include/drm/drm_edid.h +0 -0
  #endif /* __DRM_EDID_H__ */
include/drm/drm_scdc_helper.h +22 -0
index 9c52deb..ab6bcfb 100644
@@ -129,4 +129,31 @@ static inline int drm_scdc_writeb(struct i2c_adapter *adapter, u8 offset,
  	return drm_scdc_write(adapter, offset, &value, sizeof(value));
  }
 
+/**
+ * drm_scdc_set_scrambling - enable scrambling
+ * @adapter: I2C adapter for DDC channel
+ * @enable: bool to indicate if scrambling is to be enabled/disabled
+ *
+ * Writes the TMDS config register over SCDC channel, and:
+ * enables scrambling when enable = 1
+ * disables scrambling when enable = 0
+ *
+ * Returns:
+ * True if scrambling is set/reset successfully, false otherwise.
+ */
+bool drm_scdc_set_scrambling(struct i2c_adapter *adapter, bool enable);
+
+/**
+ * drm_scdc_set_high_tmds_clock_ratio - set TMDS clock ratio
+ * @adapter: I2C adapter for DDC channel
+ * @set: ret or reset the high clock ratio
+ *
+ * Writes to the TMDS config register over SCDC channel, and:
+ * sets TMDS clock ratio to 1/40 when set = 1
+ * sets TMDS clock ratio to 1/10 when set = 0
Quoted 8 lines
Quoted 8 lines
include/drm/drm_scdc_helper.h +5 -0
+ *
+ * Returns:
+ * True if write is successful, false otherwise.
+ */
+bool drm_scdc_set_high_tmds_clock_ratio(struct i2c_adapter *adapter, bool set);
  #endif
Signature · 1 line
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#7 lore raw

PATCH v5 5/6 drm/i915: enable scrambling

In reply to Shashank Sharma

Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.

This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.

V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port.

V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec.

V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio

V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks.

---
 drivers/gpu/drm/i915/i915_reg.h   |  4 ++
 drivers/gpu/drm/i915/intel_ddi.c  | 29 ++++++++++++
 drivers/gpu/drm/i915/intel_drv.h  | 14 ++++++
 drivers/gpu/drm/i915/intel_hdmi.c | 98 +++++++++++++++++++++++++++++++++++++++
 4 files changed, 145 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +4 -0
index ce6f096..1759b64 100644
@@ -7824,7 +7824,11 @@ enum {
 #define  TRANS_DDI_EDP_INPUT_B_ONOFF	(5<<12)
 #define  TRANS_DDI_EDP_INPUT_C_ONOFF	(6<<12)
 #define  TRANS_DDI_DP_VC_PAYLOAD_ALLOC	(1<<8)
+#define  TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7)
+#define  TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6)
 #define  TRANS_DDI_BFI_ENABLE		(1<<4)
+#define  TRANS_DDI_HIGH_TMDS_CHAR_RATE	(1<<4)
+#define  TRANS_DDI_HDMI_SCRAMBLING	(1<<0)
 
 /* DisplayPort Transport Control */
 #define _DP_TP_CTL_A			0x64040
drivers/gpu/drm/i915/intel_ddi.c +29 -0
index a7c08d7..24bc3a8 100644
@@ -1311,6 +1311,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc)
 			temp |= TRANS_DDI_MODE_SELECT_HDMI;
 		else
 			temp |= TRANS_DDI_MODE_SELECT_DVI;
+
+		if (IS_GEMINILAKE(dev_priv))
+			temp = intel_hdmi_handle_source_scrambling(
+				intel_encoder,
+				intel_crtc->config, temp);
 	} else if (type == INTEL_OUTPUT_ANALOG) {
 		temp |= TRANS_DDI_MODE_SELECT_FDI;
 		temp |= (intel_crtc->config->fdi_lanes - 1) << 1;
@@ -1885,6 +1890,21 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder,
 		struct intel_digital_port *intel_dig_port =
 			enc_to_dig_port(encoder);
 
+		if (IS_GEMINILAKE(dev_priv)) {
+			struct intel_crtc *crtc = to_intel_crtc(encoder->crtc);
+			/*
+			 * GLK sports a native HDMI 2.0 controller. If required
+			 * clock rate is > 340 Mhz && scrambling is supported
+			 * by sink, enable scrambling before enabling the
+			 * HDMI 2.0 port. The sink can choose to disable the
+			 * scrambling if it doesn't detect a scrambled within
+			 * 100 ms.
+			 */
+			intel_hdmi_handle_sink_scrambling(intel_encoder,
+						conn_state->connector,
+						crtc->config, true);
+		}
+
 		/* In HDMI/DVI mode, the port width, and swing/emphasis values
 		 * are ignored so nothing special needs to be done besides
 		 * enabling the port.
@@ -1912,11 +1932,20 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder,
 			      struct drm_connector_state *old_conn_state)
 {
 	struct drm_encoder *encoder = &intel_encoder->base;
+	struct drm_i915_private *dev_priv = encoder->dev->dev_private;
 	int type = intel_encoder->type;
 
 	if (old_crtc_state->has_audio)
 		intel_audio_codec_disable(intel_encoder);
 
+	if ((type == INTEL_OUTPUT_HDMI) && IS_GEMINILAKE(dev_priv)) {
+		struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
+
+		intel_hdmi_handle_sink_scrambling(intel_encoder,
+					old_conn_state->connector,
+					intel_crtc->config, false);
+	}
+
 	if (type == INTEL_OUTPUT_EDP) {
 		struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 
drivers/gpu/drm/i915/intel_drv.h +14 -0
index 907fb00..0e53fcd 100644
@@ -695,6 +695,12 @@ struct intel_crtc_state {
 
 	/* Gamma mode programmed on the pipe */
 	uint32_t gamma_mode;
+
+	/* HDMI scrambling status (sink) */
+	bool hdmi_scrambling;
+
+	/* HDMI High TMDS char rate ratio (sink) */
+	bool hdmi_high_tmds_clock_ratio;
 };
 
 struct vlv_wm_state {
@@ -1626,6 +1632,14 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,
 bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 			       struct intel_crtc_state *pipe_config,
 			       struct drm_connector_state *conn_state);
+uint32_t
+intel_hdmi_handle_source_scrambling(struct intel_encoder *intel_encoder,
+					struct intel_crtc_state *config,
+					uint32_t hdmi_config);
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+					struct drm_connector *connector,
+					struct intel_crtc_state *config,
+					bool enable);
 void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable);
 
 
drivers/gpu/drm/i915/intel_hdmi.c +98 -0

122 lines not on this page · raw message

Signature · 6 lines
1.9.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#8 lore raw

Re: [PATCH v5 5/6] drm/i915: enable scrambling

Quoted 92 lines · Shashank Sharma

Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.

This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.

V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port.

V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec.

V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio

V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks.

---
 drivers/gpu/drm/i915/i915_reg.h   |  4 ++
 drivers/gpu/drm/i915/intel_ddi.c  | 29 ++++++++++++
 drivers/gpu/drm/i915/intel_drv.h  | 14 ++++++
 drivers/gpu/drm/i915/intel_hdmi.c | 98 +++++++++++++++++++++++++++++++++++++++
 4 files changed, 145 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +4 -0
index ce6f096..1759b64 100644
@@ -7824,7 +7824,11 @@ enum {
 #define  TRANS_DDI_EDP_INPUT_B_ONOFF	(5<<12)
 #define  TRANS_DDI_EDP_INPUT_C_ONOFF	(6<<12)
 #define  TRANS_DDI_DP_VC_PAYLOAD_ALLOC	(1<<8)
+#define  TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7)
+#define  TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6)
 #define  TRANS_DDI_BFI_ENABLE		(1<<4)
+#define  TRANS_DDI_HIGH_TMDS_CHAR_RATE	(1<<4)
+#define  TRANS_DDI_HDMI_SCRAMBLING	(1<<0)
 
 /* DisplayPort Transport Control */
 #define _DP_TP_CTL_A			0x64040
drivers/gpu/drm/i915/intel_ddi.c +20 -0
index a7c08d7..24bc3a8 100644
@@ -1311,6 +1311,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc)
 			temp |= TRANS_DDI_MODE_SELECT_HDMI;
 		else
 			temp |= TRANS_DDI_MODE_SELECT_DVI;
+
+		if (IS_GEMINILAKE(dev_priv))
+			temp = intel_hdmi_handle_source_scrambling(
+				intel_encoder,
+				intel_crtc->config, temp);
 	} else if (type == INTEL_OUTPUT_ANALOG) {
 		temp |= TRANS_DDI_MODE_SELECT_FDI;
 		temp |= (intel_crtc->config->fdi_lanes - 1) << 1;
@@ -1885,6 +1890,21 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder,
 		struct intel_digital_port *intel_dig_port =
 			enc_to_dig_port(encoder);
 
+		if (IS_GEMINILAKE(dev_priv)) {
+			struct intel_crtc *crtc = to_intel_crtc(encoder->crtc);
+			/*
+			 * GLK sports a native HDMI 2.0 controller. If required
+			 * clock rate is > 340 Mhz && scrambling is supported
+			 * by sink, enable scrambling before enabling the
+			 * HDMI 2.0 port. The sink can choose to disable the
+			 * scrambling if it doesn't detect a scrambled within
+			 * 100 ms.
+			 */
+			intel_hdmi_handle_sink_scrambling(intel_encoder,
+						conn_state->connector,
+						crtc->config, true);
+		}
+
 		/* In HDMI/DVI mode, the port width, and swing/emphasis values
 		 * are ignored so nothing special needs to be done besides
 		 * enabling the port.

drivers/gpu/drm/i915/intel_ddi.c static void intel_disable_ddi(struct intel_encoder *intel_encoder, · line 1941

Quoted 10 lines
drivers/gpu/drm/i915/intel_ddi.c +2 -0
@@ -1912,11 +1932,20 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder,
 			      struct drm_connector_state *old_conn_state)
 {
 	struct drm_encoder *encoder = &intel_encoder->base;
+	struct drm_i915_private *dev_priv = encoder->dev->dev_private;
 	int type = intel_encoder->type;
 
 	if (old_crtc_state->has_audio)
 		intel_audio_codec_disable(intel_encoder);
 
+	if ((type == INTEL_OUTPUT_HDMI) && IS_GEMINILAKE(dev_priv)) {

^ ^

Pointless parens. Also I'm nor sure we want the platform check here. Seems to me that we should be able to just explicitly configure the sink on every platform, iff the sink supports SCDC of course.

Quoted 63 lines
drivers/gpu/drm/i915/intel_ddi.c +7 -0
+		struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
+
+		intel_hdmi_handle_sink_scrambling(intel_encoder,
+					old_conn_state->connector,
+					intel_crtc->config, false);
+	}
+
 	if (type == INTEL_OUTPUT_EDP) {
 		struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 
drivers/gpu/drm/i915/intel_drv.h +14 -0
index 907fb00..0e53fcd 100644
@@ -695,6 +695,12 @@ struct intel_crtc_state {
 
 	/* Gamma mode programmed on the pipe */
 	uint32_t gamma_mode;
+
+	/* HDMI scrambling status (sink) */
+	bool hdmi_scrambling;
+
+	/* HDMI High TMDS char rate ratio (sink) */
+	bool hdmi_high_tmds_clock_ratio;
 };
 
 struct vlv_wm_state {
@@ -1626,6 +1632,14 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,
 bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 			       struct intel_crtc_state *pipe_config,
 			       struct drm_connector_state *conn_state);
+uint32_t
+intel_hdmi_handle_source_scrambling(struct intel_encoder *intel_encoder,
+					struct intel_crtc_state *config,
+					uint32_t hdmi_config);
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+					struct drm_connector *connector,
+					struct intel_crtc_state *config,
+					bool enable);
 void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable);
 
 
drivers/gpu/drm/i915/intel_hdmi.c +2 -0
index c2184f7..fdbeefd 100644
@@ -34,6 +34,7 @@
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_crtc.h>
 #include <drm/drm_edid.h>
+#include <drm/drm_scdc_helper.h>
 #include "intel_drv.h"
 #include <drm/i915_drm.h>
 #include <drm/intel_lpe_audio.h>
@@ -1316,6 +1317,7 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&encoder->base);
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
 	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
+	struct drm_scdc *scdc = &conn_state->connector->display_info.hdmi.scdc;
 	int clock_8bpc = pipe_config->base.adjusted_mode.crtc_clock;
 	int clock_12bpc = clock_8bpc * 3 / 2;
 	int desired_bpp;

drivers/gpu/drm/i915/intel_hdmi.c bool intel_hdmi_compute_config(struct intel_encoder *encoder, · line 1390

Quoted 4 lines
drivers/gpu/drm/i915/intel_hdmi.c +1 -0
@@ -1385,6 +1387,16 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 
 	pipe_config->lane_count = 4;
 
+	if (scdc->scrambling.supported) {

Here we should have a check whether the source support scrambling or not.

Quoted 62 lines
drivers/gpu/drm/i915/intel_hdmi.c +55 -0
+		if (scdc->scrambling.low_rates)
+			pipe_config->hdmi_scrambling = true;
+
+		if (pipe_config->port_clock > 340000) {
+			pipe_config->hdmi_scrambling = true;
+			pipe_config->hdmi_high_tmds_clock_ratio = true;
+		}
+	}
+
 	return true;
 }
 
@@ -1794,6 +1806,92 @@ static void intel_hdmi_destroy(struct drm_connector *connector)
 	intel_hdmi->aspect_ratio = HDMI_PICTURE_ASPECT_NONE;
 }
 
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+				       struct drm_connector *connector,
+				       struct intel_crtc_state *config,
+				       bool enable)
+{
+	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&intel_encoder->base);
+	struct drm_i915_private *dev_priv = connector->dev->dev_private;
+	struct drm_scrambling *scrambling =
+				&connector->display_info.hdmi.scdc.scrambling;
+	struct i2c_adapter *adptr = intel_gmbus_get_adapter(dev_priv,
+							  intel_hdmi->ddc_bus);
+	bool ret;
+
+	if (!scrambling->supported)
+		return;
+
+	DRM_DEBUG_KMS("Setting sink scrambling for enc:%s connector:%s\n",
+			intel_encoder->base.name, connector->name);
+
+	if (enable) {
+
+		if (config->hdmi_high_tmds_clock_ratio) {
+			/* Set TMDS bit clock ratio to 1/40 */
+			ret = drm_scdc_set_high_tmds_clock_ratio(adptr, true);
+			if (!ret) {
+				DRM_ERROR("Set high TMDS ratio failed\n");
+				return;
+			}
+		}
+
+		if (config->hdmi_scrambling) {
+			/* Enable sink scrambling */
+			ret = drm_scdc_set_scrambling(adptr, true);
+			if (!ret) {
+				DRM_ERROR("Can't enable sink scrambling\n");
+				return;
+			}
+		}
+
+		DRM_DEBUG_KMS("sink scrambling enabled\n");
+		return;
+	}
+
+	if (config->hdmi_high_tmds_clock_ratio) {
+		/* Set TMDS bit clock ratio back to 1/10 */
+		ret = !(drm_scdc_set_high_tmds_clock_ratio(adptr, false));

drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1864

Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +10 -0
+		if (ret)
+			DRM_ERROR("Reset high TMDS ratio failed\n");
+	}
+
+	if (config->hdmi_scrambling) {
+		/* Disable sink scrambling */
+		ret = !(drm_scdc_set_scrambling(adptr, false));
+		if (ret)
+			DRM_ERROR("Disable sink scrambling failed\n");
+	}

Seems a little complicated for what it's doing.

I'd go for something simple like:

foo(bool scrambling, bool clock_ratio)

{
	set_scrambling(scrambling);
	set_clock_ratio(clock_ratio);
}

enable()

{
	foo(crtc_state->hdmi_scrambling, crtc_state->clock_ratio);
}

disable()

{
	foo(false, false);
}
Quoted 16 lines
drivers/gpu/drm/i915/intel_hdmi.c +16 -0
+
+	DRM_DEBUG_KMS("sink scrambling disabled\n");
+}
+
+uint32_t
+intel_hdmi_handle_source_scrambling(struct intel_encoder *intel_encoder,
+			struct intel_crtc_state *config, uint32_t hdmi_config)
+{
+	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&intel_encoder->base);
+	struct drm_connector *connector = &intel_hdmi->attached_connector->base;
+
+	DRM_DEBUG_KMS("Setting scrambling for enc:%s connector:%s\n",
+			intel_encoder->base.name, connector->name);
+
+	hdmi_config &= ~(TRANS_DDI_HDMI_SCRAMBLING |
+		TRANS_DDI_HIGH_TMDS_CHAR_RATE |

drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1890

Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +10 -0
+		TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ |
+		TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE);
+
+	if (config->hdmi_scrambling)
+		hdmi_config |= (TRANS_DDI_HDMI_SCRAMBLING |
+			TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ |
+			TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE);
+
+	if (config->hdmi_high_tmds_clock_ratio)
+		hdmi_config |= TRANS_DDI_HIGH_TMDS_CHAR_RATE;

IMO just inline these two things into the function that configures this register. Having to jump around between functions is just extra pain we don't need IMO.

There should also be corresponding readout code for this in intel_ddi_get_config(), and matching PIPE_CONF_CHECK stuff in intel_pipe_config_compare().

Quoted 9 lines
drivers/gpu/drm/i915/intel_hdmi.c +4 -0
+
+	return hdmi_config;
+}
+
 static u8 intel_hdmi_ddc_pin(struct drm_i915_private *dev_priv,
 			     enum port port)
 {
Signature · 1 line
1.9.1
Signature · 6 lines
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#9 lore raw

Re: [PATCH v5 5/6] drm/i915: enable scrambling

Regards

Shashank

Quoted 102 lines · Ville Syrjälä
Quoted 101 lines · Shashank Sharma

Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.

This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.

V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port.

V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec.

V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling

    high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio

V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks.

---
  drivers/gpu/drm/i915/i915_reg.h   |  4 ++
  drivers/gpu/drm/i915/intel_ddi.c  | 29 ++++++++++++
  drivers/gpu/drm/i915/intel_drv.h  | 14 ++++++
  drivers/gpu/drm/i915/intel_hdmi.c | 98 +++++++++++++++++++++++++++++++++++++++
  4 files changed, 145 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +4 -0
index ce6f096..1759b64 100644
@@ -7824,7 +7824,11 @@ enum {
  #define  TRANS_DDI_EDP_INPUT_B_ONOFF	(5<<12)
  #define  TRANS_DDI_EDP_INPUT_C_ONOFF	(6<<12)
  #define  TRANS_DDI_DP_VC_PAYLOAD_ALLOC	(1<<8)
+#define  TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7)
+#define  TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6)
  #define  TRANS_DDI_BFI_ENABLE		(1<<4)
+#define  TRANS_DDI_HIGH_TMDS_CHAR_RATE	(1<<4)
+#define  TRANS_DDI_HDMI_SCRAMBLING	(1<<0)
 
  /* DisplayPort Transport Control */
  #define _DP_TP_CTL_A			0x64040
drivers/gpu/drm/i915/intel_ddi.c +21 -0
index a7c08d7..24bc3a8 100644
@@ -1311,6 +1311,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc)
  			temp |= TRANS_DDI_MODE_SELECT_HDMI;
  		else
  			temp |= TRANS_DDI_MODE_SELECT_DVI;
+
+		if (IS_GEMINILAKE(dev_priv))
+			temp = intel_hdmi_handle_source_scrambling(
+				intel_encoder,
+				intel_crtc->config, temp);
  	} else if (type == INTEL_OUTPUT_ANALOG) {
  		temp |= TRANS_DDI_MODE_SELECT_FDI;
  		temp |= (intel_crtc->config->fdi_lanes - 1) << 1;
@@ -1885,6 +1890,21 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder,
  		struct intel_digital_port *intel_dig_port =
  			enc_to_dig_port(encoder);
 
+		if (IS_GEMINILAKE(dev_priv)) {
+			struct intel_crtc *crtc = to_intel_crtc(encoder->crtc);
+			/*
+			 * GLK sports a native HDMI 2.0 controller. If required
+			 * clock rate is > 340 Mhz && scrambling is supported
+			 * by sink, enable scrambling before enabling the
+			 * HDMI 2.0 port. The sink can choose to disable the
+			 * scrambling if it doesn't detect a scrambled within
+			 * 100 ms.
+			 */
+			intel_hdmi_handle_sink_scrambling(intel_encoder,
+						conn_state->connector,
+						crtc->config, true);
+		}
+
  		/* In HDMI/DVI mode, the port width, and swing/emphasis values
  		 * are ignored so nothing special needs to be done besides
  		 * enabling the port.
@@ -1912,11 +1932,20 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder,
  			      struct drm_connector_state *old_conn_state)
  {
  	struct drm_encoder *encoder = &intel_encoder->base;
+	struct drm_i915_private *dev_priv = encoder->dev->dev_private;
  	int type = intel_encoder->type;
 
  	if (old_crtc_state->has_audio)
  		intel_audio_codec_disable(intel_encoder);
 
Quoted 6 lines

drivers/gpu/drm/i915/intel_ddi.c static void intel_disable_ddi(struct intel_encoder *intel_encoder, · line 1941

Quoted 1 line
drivers/gpu/drm/i915/intel_ddi.c +1 -0
+	if ((type == INTEL_OUTPUT_HDMI) && IS_GEMINILAKE(dev_priv)) {

^ ^

Pointless parens. Also I'm nor sure we want the platform check here. Seems to me that we should be able to just explicitly configure the sink on every platform, iff the sink supports SCDC of course.

This is interesting, what if I connect a HDMI 2.0 sink, which supports scrambling to a GEN8 or non-lspcon GEN 9 device ? Shouldn't we check if the source also allows it ?

Quoted 64 lines
Quoted 64 lines
drivers/gpu/drm/i915/intel_ddi.c +7 -0
+		struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
+
+		intel_hdmi_handle_sink_scrambling(intel_encoder,
+					old_conn_state->connector,
+					intel_crtc->config, false);
+	}
+
  	if (type == INTEL_OUTPUT_EDP) {
  		struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 
drivers/gpu/drm/i915/intel_drv.h +14 -0
index 907fb00..0e53fcd 100644
@@ -695,6 +695,12 @@ struct intel_crtc_state {
 
  	/* Gamma mode programmed on the pipe */
  	uint32_t gamma_mode;
+
+	/* HDMI scrambling status (sink) */
+	bool hdmi_scrambling;
+
+	/* HDMI High TMDS char rate ratio (sink) */
+	bool hdmi_high_tmds_clock_ratio;
  };
 
  struct vlv_wm_state {
@@ -1626,6 +1632,14 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,
  bool intel_hdmi_compute_config(struct intel_encoder *encoder,
  			       struct intel_crtc_state *pipe_config,
  			       struct drm_connector_state *conn_state);
+uint32_t
+intel_hdmi_handle_source_scrambling(struct intel_encoder *intel_encoder,
+					struct intel_crtc_state *config,
+					uint32_t hdmi_config);
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+					struct drm_connector *connector,
+					struct intel_crtc_state *config,
+					bool enable);
  void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable);
 
 
drivers/gpu/drm/i915/intel_hdmi.c +2 -0
index c2184f7..fdbeefd 100644
@@ -34,6 +34,7 @@
  #include <drm/drm_atomic_helper.h>
  #include <drm/drm_crtc.h>
  #include <drm/drm_edid.h>
+#include <drm/drm_scdc_helper.h>
  #include "intel_drv.h"
  #include <drm/i915_drm.h>
  #include <drm/intel_lpe_audio.h>
@@ -1316,6 +1317,7 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
  	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&encoder->base);
  	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
  	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
+	struct drm_scdc *scdc = &conn_state->connector->display_info.hdmi.scdc;
  	int clock_8bpc = pipe_config->base.adjusted_mode.crtc_clock;
  	int clock_12bpc = clock_8bpc * 3 / 2;
  	int desired_bpp;
@@ -1385,6 +1387,16 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 
Quoted 4 lines

drivers/gpu/drm/i915/intel_hdmi.c bool intel_hdmi_compute_config(struct intel_encoder *encoder, · line 1390

Quoted 3 lines
drivers/gpu/drm/i915/intel_hdmi.c +1 -0
  	pipe_config->lane_count = 4;
 
+	if (scdc->scrambling.supported) {

Here we should have a check whether the source support scrambling or not.

Ok, makes sense.

Quoted 84 lines
Quoted 63 lines
drivers/gpu/drm/i915/intel_hdmi.c +55 -0
+		if (scdc->scrambling.low_rates)
+			pipe_config->hdmi_scrambling = true;
+
+		if (pipe_config->port_clock > 340000) {
+			pipe_config->hdmi_scrambling = true;
+			pipe_config->hdmi_high_tmds_clock_ratio = true;
+		}
+	}
+
  	return true;
  }
 
@@ -1794,6 +1806,92 @@ static void intel_hdmi_destroy(struct drm_connector *connector)
  	intel_hdmi->aspect_ratio = HDMI_PICTURE_ASPECT_NONE;
  }
 
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+				       struct drm_connector *connector,
+				       struct intel_crtc_state *config,
+				       bool enable)
+{
+	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&intel_encoder->base);
+	struct drm_i915_private *dev_priv = connector->dev->dev_private;
+	struct drm_scrambling *scrambling =
+				&connector->display_info.hdmi.scdc.scrambling;
+	struct i2c_adapter *adptr = intel_gmbus_get_adapter(dev_priv,
+							  intel_hdmi->ddc_bus);
+	bool ret;
+
+	if (!scrambling->supported)
+		return;
+
+	DRM_DEBUG_KMS("Setting sink scrambling for enc:%s connector:%s\n",
+			intel_encoder->base.name, connector->name);
+
+	if (enable) {
+
+		if (config->hdmi_high_tmds_clock_ratio) {
+			/* Set TMDS bit clock ratio to 1/40 */
+			ret = drm_scdc_set_high_tmds_clock_ratio(adptr, true);
+			if (!ret) {
+				DRM_ERROR("Set high TMDS ratio failed\n");
+				return;
+			}
+		}
+
+		if (config->hdmi_scrambling) {
+			/* Enable sink scrambling */
+			ret = drm_scdc_set_scrambling(adptr, true);
+			if (!ret) {
+				DRM_ERROR("Can't enable sink scrambling\n");
+				return;
+			}
+		}
+
+		DRM_DEBUG_KMS("sink scrambling enabled\n");
+		return;
+	}
+
+	if (config->hdmi_high_tmds_clock_ratio) {
+		/* Set TMDS bit clock ratio back to 1/10 */
+		ret = !(drm_scdc_set_high_tmds_clock_ratio(adptr, false));

drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1864

Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +10 -0
+		if (ret)
+			DRM_ERROR("Reset high TMDS ratio failed\n");
+	}
+
+	if (config->hdmi_scrambling) {
+		/* Disable sink scrambling */
+		ret = !(drm_scdc_set_scrambling(adptr, false));
+		if (ret)
+			DRM_ERROR("Disable sink scrambling failed\n");
+	}

Seems a little complicated for what it's doing.

I'd go for something simple like:

foo(bool scrambling, bool clock_ratio)

{
	set_scrambling(scrambling);
	set_clock_ratio(clock_ratio);
}

enable()

Quoted 8 lines
{
	foo(crtc_state->hdmi_scrambling, crtc_state->clock_ratio);
}

disable()

{
	foo(false, false);
}

In the first look, I thought intel_hdmi_handle_sink_scrambling is your foo, but later I realized, you dont want an if (enable) cond.... will take care of it.

Quoted 22 lines
Quoted 22 lines
drivers/gpu/drm/i915/intel_hdmi.c +21 -0
+
+	DRM_DEBUG_KMS("sink scrambling disabled\n");
+}
+
+uint32_t
+intel_hdmi_handle_source_scrambling(struct intel_encoder *intel_encoder,
+			struct intel_crtc_state *config, uint32_t hdmi_config)
+{
+	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&intel_encoder->base);
+	struct drm_connector *connector = &intel_hdmi->attached_connector->base;
+
+	DRM_DEBUG_KMS("Setting scrambling for enc:%s connector:%s\n",
+			intel_encoder->base.name, connector->name);
+
+	hdmi_config &= ~(TRANS_DDI_HDMI_SCRAMBLING |
+		TRANS_DDI_HIGH_TMDS_CHAR_RATE |
+		TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ |
+		TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE);
+
+	if (config->hdmi_scrambling)
+		hdmi_config |= (TRANS_DDI_HDMI_SCRAMBLING |
Quoted 8 lines

drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1890

Quoted 5 lines
drivers/gpu/drm/i915/intel_hdmi.c +5 -0
+			TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ |
+			TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE);
+
+	if (config->hdmi_high_tmds_clock_ratio)
+		hdmi_config |= TRANS_DDI_HIGH_TMDS_CHAR_RATE;

IMO just inline these two things into the function that configures this register. Having to jump around between functions is just extra pain we don't need IMO.

Not really, this function is also making sure, that the scrambling bits are cleared, and only enabled which is required. Also, this is making code more readable, segregating scrambling functionalities, and better for debugging too. Lets keep this one if you please allow.

Quoted 3 lines

There should also be corresponding readout code for this in intel_ddi_get_config(), and matching PIPE_CONF_CHECK stuff in intel_pipe_config_compare().

Agree, will add that too.

- Shashank

Quoted 9 lines
Quoted 9 lines
drivers/gpu/drm/i915/intel_hdmi.c +4 -0
+
+	return hdmi_config;
+}
+
  static u8 intel_hdmi_ddc_pin(struct drm_i915_private *dev_priv,
  			     enum port port)
  {
Signature · 1 line
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#10 lore raw

Re: [PATCH v5 5/6] drm/i915: enable scrambling

Quoted 319 lines · Shashank

Regards

Shashank

Quoted 102 lines · Ville Syrjälä
Quoted 101 lines · Shashank Sharma

Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.

This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.

V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port.

V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec.

V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling

    high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio

V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks.

---
  drivers/gpu/drm/i915/i915_reg.h   |  4 ++
  drivers/gpu/drm/i915/intel_ddi.c  | 29 ++++++++++++
  drivers/gpu/drm/i915/intel_drv.h  | 14 ++++++
  drivers/gpu/drm/i915/intel_hdmi.c | 98 +++++++++++++++++++++++++++++++++++++++
  4 files changed, 145 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +4 -0
index ce6f096..1759b64 100644
@@ -7824,7 +7824,11 @@ enum {
  #define  TRANS_DDI_EDP_INPUT_B_ONOFF	(5<<12)
  #define  TRANS_DDI_EDP_INPUT_C_ONOFF	(6<<12)
  #define  TRANS_DDI_DP_VC_PAYLOAD_ALLOC	(1<<8)
+#define  TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7)
+#define  TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6)
  #define  TRANS_DDI_BFI_ENABLE		(1<<4)
+#define  TRANS_DDI_HIGH_TMDS_CHAR_RATE	(1<<4)
+#define  TRANS_DDI_HDMI_SCRAMBLING	(1<<0)
 
  /* DisplayPort Transport Control */
  #define _DP_TP_CTL_A			0x64040
drivers/gpu/drm/i915/intel_ddi.c +21 -0
index a7c08d7..24bc3a8 100644
@@ -1311,6 +1311,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc)
  			temp |= TRANS_DDI_MODE_SELECT_HDMI;
  		else
  			temp |= TRANS_DDI_MODE_SELECT_DVI;
+
+		if (IS_GEMINILAKE(dev_priv))
+			temp = intel_hdmi_handle_source_scrambling(
+				intel_encoder,
+				intel_crtc->config, temp);
  	} else if (type == INTEL_OUTPUT_ANALOG) {
  		temp |= TRANS_DDI_MODE_SELECT_FDI;
  		temp |= (intel_crtc->config->fdi_lanes - 1) << 1;
@@ -1885,6 +1890,21 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder,
  		struct intel_digital_port *intel_dig_port =
  			enc_to_dig_port(encoder);
 
+		if (IS_GEMINILAKE(dev_priv)) {
+			struct intel_crtc *crtc = to_intel_crtc(encoder->crtc);
+			/*
+			 * GLK sports a native HDMI 2.0 controller. If required
+			 * clock rate is > 340 Mhz && scrambling is supported
+			 * by sink, enable scrambling before enabling the
+			 * HDMI 2.0 port. The sink can choose to disable the
+			 * scrambling if it doesn't detect a scrambled within
+			 * 100 ms.
+			 */
+			intel_hdmi_handle_sink_scrambling(intel_encoder,
+						conn_state->connector,
+						crtc->config, true);
+		}
+
  		/* In HDMI/DVI mode, the port width, and swing/emphasis values
  		 * are ignored so nothing special needs to be done besides
  		 * enabling the port.
@@ -1912,11 +1932,20 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder,
  			      struct drm_connector_state *old_conn_state)
  {
  	struct drm_encoder *encoder = &intel_encoder->base;
+	struct drm_i915_private *dev_priv = encoder->dev->dev_private;
  	int type = intel_encoder->type;
 
  	if (old_crtc_state->has_audio)
  		intel_audio_codec_disable(intel_encoder);
 
Quoted 7 lines

drivers/gpu/drm/i915/intel_ddi.c static void intel_disable_ddi(struct intel_encoder *intel_encoder, · line 1941

Quoted 1 line
drivers/gpu/drm/i915/intel_ddi.c +1 -0
+	if ((type == INTEL_OUTPUT_HDMI) && IS_GEMINILAKE(dev_priv)) {

^ ^

Pointless parens. Also I'm nor sure we want the platform check here. Seems to me that we should be able to just explicitly configure the sink on every platform, iff the sink supports SCDC of course.

This is interesting, what if I connect a HDMI 2.0 sink, which supports scrambling to a GEN8 or non-lspcon
GEN 9 device ? Shouldn't we check if the source also allows it ?

Quoted 64 lines
Quoted 64 lines
drivers/gpu/drm/i915/intel_ddi.c +7 -0
+		struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
+
+		intel_hdmi_handle_sink_scrambling(intel_encoder,
+					old_conn_state->connector,
+					intel_crtc->config, false);
+	}
+
  	if (type == INTEL_OUTPUT_EDP) {
  		struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 
drivers/gpu/drm/i915/intel_drv.h +14 -0
index 907fb00..0e53fcd 100644
@@ -695,6 +695,12 @@ struct intel_crtc_state {
 
  	/* Gamma mode programmed on the pipe */
  	uint32_t gamma_mode;
+
+	/* HDMI scrambling status (sink) */
+	bool hdmi_scrambling;
+
+	/* HDMI High TMDS char rate ratio (sink) */
+	bool hdmi_high_tmds_clock_ratio;
  };
 
  struct vlv_wm_state {
@@ -1626,6 +1632,14 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,
  bool intel_hdmi_compute_config(struct intel_encoder *encoder,
  			       struct intel_crtc_state *pipe_config,
  			       struct drm_connector_state *conn_state);
+uint32_t
+intel_hdmi_handle_source_scrambling(struct intel_encoder *intel_encoder,
+					struct intel_crtc_state *config,
+					uint32_t hdmi_config);
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+					struct drm_connector *connector,
+					struct intel_crtc_state *config,
+					bool enable);
  void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable);
 
 
drivers/gpu/drm/i915/intel_hdmi.c +2 -0
index c2184f7..fdbeefd 100644
@@ -34,6 +34,7 @@
  #include <drm/drm_atomic_helper.h>
  #include <drm/drm_crtc.h>
  #include <drm/drm_edid.h>
+#include <drm/drm_scdc_helper.h>
  #include "intel_drv.h"
  #include <drm/i915_drm.h>
  #include <drm/intel_lpe_audio.h>
@@ -1316,6 +1317,7 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
  	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&encoder->base);
  	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
  	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
+	struct drm_scdc *scdc = &conn_state->connector->display_info.hdmi.scdc;
  	int clock_8bpc = pipe_config->base.adjusted_mode.crtc_clock;
  	int clock_12bpc = clock_8bpc * 3 / 2;
  	int desired_bpp;
@@ -1385,6 +1387,16 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 
Quoted 5 lines

drivers/gpu/drm/i915/intel_hdmi.c bool intel_hdmi_compute_config(struct intel_encoder *encoder, · line 1390

Quoted 3 lines
drivers/gpu/drm/i915/intel_hdmi.c +1 -0
  	pipe_config->lane_count = 4;
 
+	if (scdc->scrambling.supported) {

Here we should have a check whether the source support scrambling or not.

Ok, makes sense.

Quoted 85 lines
Quoted 63 lines
drivers/gpu/drm/i915/intel_hdmi.c +55 -0
+		if (scdc->scrambling.low_rates)
+			pipe_config->hdmi_scrambling = true;
+
+		if (pipe_config->port_clock > 340000) {
+			pipe_config->hdmi_scrambling = true;
+			pipe_config->hdmi_high_tmds_clock_ratio = true;
+		}
+	}
+
  	return true;
  }
 
@@ -1794,6 +1806,92 @@ static void intel_hdmi_destroy(struct drm_connector *connector)
  	intel_hdmi->aspect_ratio = HDMI_PICTURE_ASPECT_NONE;
  }
 
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+				       struct drm_connector *connector,
+				       struct intel_crtc_state *config,
+				       bool enable)
+{
+	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&intel_encoder->base);
+	struct drm_i915_private *dev_priv = connector->dev->dev_private;
+	struct drm_scrambling *scrambling =
+				&connector->display_info.hdmi.scdc.scrambling;
+	struct i2c_adapter *adptr = intel_gmbus_get_adapter(dev_priv,
+							  intel_hdmi->ddc_bus);
+	bool ret;
+
+	if (!scrambling->supported)
+		return;
+
+	DRM_DEBUG_KMS("Setting sink scrambling for enc:%s connector:%s\n",
+			intel_encoder->base.name, connector->name);
+
+	if (enable) {
+
+		if (config->hdmi_high_tmds_clock_ratio) {
+			/* Set TMDS bit clock ratio to 1/40 */
+			ret = drm_scdc_set_high_tmds_clock_ratio(adptr, true);
+			if (!ret) {
+				DRM_ERROR("Set high TMDS ratio failed\n");
+				return;
+			}
+		}
+
+		if (config->hdmi_scrambling) {
+			/* Enable sink scrambling */
+			ret = drm_scdc_set_scrambling(adptr, true);
+			if (!ret) {
+				DRM_ERROR("Can't enable sink scrambling\n");
+				return;
+			}
+		}
+
+		DRM_DEBUG_KMS("sink scrambling enabled\n");
+		return;
+	}
+
+	if (config->hdmi_high_tmds_clock_ratio) {
+		/* Set TMDS bit clock ratio back to 1/10 */
+		ret = !(drm_scdc_set_high_tmds_clock_ratio(adptr, false));

drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1864

Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +10 -0
+		if (ret)
+			DRM_ERROR("Reset high TMDS ratio failed\n");
+	}
+
+	if (config->hdmi_scrambling) {
+		/* Disable sink scrambling */
+		ret = !(drm_scdc_set_scrambling(adptr, false));
+		if (ret)
+			DRM_ERROR("Disable sink scrambling failed\n");
+	}

Seems a little complicated for what it's doing.

I'd go for something simple like:

foo(bool scrambling, bool clock_ratio)

{
	set_scrambling(scrambling);
	set_clock_ratio(clock_ratio);
}

enable()

Quoted 8 lines
{
	foo(crtc_state->hdmi_scrambling, crtc_state->clock_ratio);
}

disable()

{
	foo(false, false);
}

In the first look, I thought intel_hdmi_handle_sink_scrambling is your foo, but later I realized,
you dont want an if (enable) cond.... will take care of it.

Quoted 23 lines
Quoted 23 lines
drivers/gpu/drm/i915/intel_hdmi.c +22 -0
+
+	DRM_DEBUG_KMS("sink scrambling disabled\n");
+}
+
+uint32_t
+intel_hdmi_handle_source_scrambling(struct intel_encoder *intel_encoder,
+			struct intel_crtc_state *config, uint32_t hdmi_config)
+{
+	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&intel_encoder->base);
+	struct drm_connector *connector = &intel_hdmi->attached_connector->base;
+
+	DRM_DEBUG_KMS("Setting scrambling for enc:%s connector:%s\n",
+			intel_encoder->base.name, connector->name);
+
+	hdmi_config &= ~(TRANS_DDI_HDMI_SCRAMBLING |
+		TRANS_DDI_HIGH_TMDS_CHAR_RATE |
+		TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ |
+		TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE);
+
+	if (config->hdmi_scrambling)
+		hdmi_config |= (TRANS_DDI_HDMI_SCRAMBLING |
+			TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ |
Quoted 8 lines

drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1890

Quoted 4 lines
drivers/gpu/drm/i915/intel_hdmi.c +4 -0
+			TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE);
+
+	if (config->hdmi_high_tmds_clock_ratio)
+		hdmi_config |= TRANS_DDI_HIGH_TMDS_CHAR_RATE;

IMO just inline these two things into the function that configures this register. Having to jump around between functions is just extra pain we don't need IMO.

Quoted 2 lines

Not really, this function is also making sure, that the scrambling bits are cleared,

There is no read-modify-write in intel_ddi_enable_transcoder_func(). Every bit that is not explicitly set is cleared.

Quoted 5 lines

and only
enabled which is required. Also, this is making code more readable, segregating scrambling
functionalities, and better for debugging too. Lets keep this one if you please allow.

I think the extra function makes it harder to read. The function intel_ddi_enable_transcoder_func() only translates the current configuration to the right bits that need to be programmed to TRANS_DDI_FUNC_CTL. That belongs in intel_ddi.c.

To help with debugging, add HDMI scrambling prints to intel_dump_pipe_config(). That's actually more useful than the print in this function since it can also tell us if scrambling was enabled for a configuration read out from hw state.

Ander

Quoted 7 lines
Quoted 3 lines

There should also be corresponding readout code for this in intel_ddi_get_config(), and matching PIPE_CONF_CHECK stuff in intel_pipe_config_compare().

Agree, will add that too.

- Shashank

Quoted 14 lines
Quoted 9 lines
Quoted 9 lines
drivers/gpu/drm/i915/intel_hdmi.c +4 -0
+
+	return hdmi_config;
+}
+
  static u8 intel_hdmi_ddc_pin(struct drm_i915_private *dev_priv,
  			     enum port port)
  {
Signature · 1 line
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#11 lore raw

PATCH v5 6/6 drm/i915: allow HDMI 2.0 clock rates

In reply to Shashank Sharma

Geminilake has a native HDMI 2.0 controller, which is capable of driving clocks upto 594Mhz. This patch updates the max tmds clock limit for the same.

V2: rebase
V3: rebase
V4: added r-b from Ander
V5: rebase

---
 drivers/gpu/drm/i915/intel_hdmi.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/gpu/drm/i915/intel_hdmi.c +2 -0
index fdbeefd..d44b9fb 100644
@@ -1209,6 +1209,8 @@ static int intel_hdmi_source_max_tmds_clock(struct drm_i915_private *dev_priv)
 {
 	if (IS_G4X(dev_priv))
 		return 165000;
+	else if (IS_GEMINILAKE(dev_priv))
+		return 594000;
 	else if (IS_HASWELL(dev_priv) || INTEL_INFO(dev_priv)->gen >= 8)
 		return 300000;
 	else
Signature · 6 lines
1.9.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#12 lore raw

✓ Fi.CI.BAT: success for HDMI 2.0: Scrambling in DRM layer (rev5)

In reply to Shashank Sharma
== Series Details ==

== Series Details ==

Series: HDMI 2.0: Scrambling in DRM layer (rev5)
URL : https://patchwork.freedesktop.org/series/19161/
State : success

== Summary ==

Series 19161v5 HDMI 2.0: Scrambling in DRM layer
https://patchwork.freedesktop.org/api/1.0/series/19161/revisions/5/mbox/

fi-bdw-5557u     total:278  pass:267  dwarn:0   dfail:0   fail:0   skip:11 
fi-bsw-n3050     total:278  pass:239  dwarn:0   dfail:0   fail:0   skip:39 
fi-bxt-j4205     total:278  pass:259  dwarn:0   dfail:0   fail:0   skip:19 
fi-bxt-t5700     total:108  pass:95   dwarn:0   dfail:0   fail:0   skip:12 
fi-byt-j1900     total:278  pass:251  dwarn:0   dfail:0   fail:0   skip:27 
fi-byt-n2820     total:278  pass:247  dwarn:0   dfail:0   fail:0   skip:31 
fi-hsw-4770      total:278  pass:262  dwarn:0   dfail:0   fail:0   skip:16 
fi-hsw-4770r     total:278  pass:262  dwarn:0   dfail:0   fail:0   skip:16 
fi-ilk-650       total:278  pass:228  dwarn:0   dfail:0   fail:0   skip:50 
fi-ivb-3520m     total:278  pass:260  dwarn:0   dfail:0   fail:0   skip:18 
fi-ivb-3770      total:278  pass:260  dwarn:0   dfail:0   fail:0   skip:18 
fi-kbl-7500u     total:278  pass:260  dwarn:0   dfail:0   fail:0   skip:18 
fi-skl-6260u     total:278  pass:268  dwarn:0   dfail:0   fail:0   skip:10 
fi-skl-6700hq    total:278  pass:261  dwarn:0   dfail:0   fail:0   skip:17 
fi-skl-6700k     total:278  pass:256  dwarn:4   dfail:0   fail:0   skip:18 
fi-skl-6770hq    total:278  pass:268  dwarn:0   dfail:0   fail:0   skip:10 
fi-snb-2520m     total:278  pass:250  dwarn:0   dfail:0   fail:0   skip:28 
fi-snb-2600      total:278  pass:249  dwarn:0   dfail:0   fail:0   skip:29 

1a8bd0fb40e5d02f827f925b7702ed6f64fadce2 drm-tip: 2017y-02m-27d-22h-04m-19s UTC integration manifest 095263d drm/i915: allow HDMI 2.0 clock rates
b07b47f drm/i915: enable scrambling
0496632 drm/edid: detect SCDC support in HF-VSDB
1c62a02 drm/edid: detect SCDC support in HF-VSDB
8834945 drm/edid: check for HF-VSDB block
3de25b7 drm: Add SCDC helpers

== Logs ==

For more details see: https://intel-gfx-ci.01.org/CI/Patchwork_3993/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx