Skip to contentSkip to conversation

ath10k: Increase BMI timeout.

PATCH In review [email protected] 2 participants 9 messages May 15, 2017 – Jun 1, 2017 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore
#0 lore raw

PATCH 1/3 ath10k: Increase BMI timeout.

From: Ben Greear <[email protected]>

When testing a 9888 chipset NIC, I notice it often takes almost 2 seconds, and then many times OTP fails, probably due to the two-second timeout.

[ 2269.841842] ath10k_pci 0000:05:00.0: bmi cmd took: 1984 jiffies (HZ: 1000), rv: 0
[ 2273.608185] ath10k_pci 0000:05:00.0: bmi cmd took: 1986 jiffies (HZ: 1000), rv: 0
[ 2277.294732] ath10k_pci 0000:05:00.0: bmi cmd took: 1989 jiffies (HZ: 1000), rv: 0

So, increase the BMI timeout to 3 seconds.

---
 drivers/net/wireless/ath/ath10k/bmi.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/wireless/ath/ath10k/bmi.h +2 -2
index 7d3231a..1054c0c 100644
@@ -187,8 +187,8 @@ struct bmi_target_info {
 	u32 type;
 };
 
-/* in msec */
-#define BMI_COMMUNICATION_TIMEOUT_HZ (2 * HZ)
+/* in jiffies */
+#define BMI_COMMUNICATION_TIMEOUT_HZ (3 * HZ)
 
 #define BMI_CE_NUM_TO_TARG 0
 #define BMI_CE_NUM_TO_HOST 1
Signature · 7 lines
2.4.11


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#5 lore raw

PATCH 3/3 ath10k: Log when longer bmi cmds happen.

From: Ben Greear <[email protected]>

This lets one have a clue that maybe timeouts are happening when we just aren't waiting long enough.

---
 drivers/net/wireless/ath/ath10k/pci.c | 25 +++++++++++++++++++------
 1 file changed, 19 insertions(+), 6 deletions(-)
drivers/net/wireless/ath/ath10k/pci.c +19 -6
index 52b9ebb..0311b07 100644
@@ -101,7 +101,8 @@ static int ath10k_pci_init_irq(struct ath10k *ar);
 static int ath10k_pci_deinit_irq(struct ath10k *ar);
 static int ath10k_pci_request_irq(struct ath10k *ar);
 static void ath10k_pci_free_irq(struct ath10k *ar);
-static int ath10k_pci_bmi_wait(struct ath10k_ce_pipe *tx_pipe,
+static int ath10k_pci_bmi_wait(struct ath10k *ar,
+			       struct ath10k_ce_pipe *tx_pipe,
 			       struct ath10k_ce_pipe *rx_pipe,
 			       struct bmi_xfer *xfer);
 static int ath10k_pci_qca99x0_chip_reset(struct ath10k *ar);
@@ -2156,7 +2157,7 @@ int ath10k_pci_hif_exchange_bmi_msg(struct ath10k *ar,
 	if (ret)
 		goto err_resp;
 
-	ret = ath10k_pci_bmi_wait(ce_tx, ce_rx, &xfer);
+	ret = ath10k_pci_bmi_wait(ar, ce_tx, ce_rx, &xfer);
 	if (ret) {
 		u32 unused_buffer;
 		unsigned int unused_nbytes;
@@ -2225,23 +2226,35 @@ static void ath10k_pci_bmi_recv_data(struct ath10k_ce_pipe *ce_state)
 	xfer->rx_done = true;
 }
 
-static int ath10k_pci_bmi_wait(struct ath10k_ce_pipe *tx_pipe,
+static int ath10k_pci_bmi_wait(struct ath10k *ar,
+			       struct ath10k_ce_pipe *tx_pipe,
 			       struct ath10k_ce_pipe *rx_pipe,
 			       struct bmi_xfer *xfer)
 {
 	unsigned long timeout = jiffies + BMI_COMMUNICATION_TIMEOUT_HZ;
+	unsigned long started = jiffies;
+	unsigned long dur;
+	int rv = -ETIMEDOUT;
 
 	while (time_before_eq(jiffies, timeout)) {
 		ath10k_pci_bmi_send_done(tx_pipe);
 		ath10k_pci_bmi_recv_data(rx_pipe);
 
-		if (xfer->tx_done && (xfer->rx_done == xfer->wait_for_resp))
-			return 0;
+		if (xfer->tx_done && (xfer->rx_done == xfer->wait_for_resp)) {
+			rv = 0;
+			goto out;
+		}
 
 		schedule();
 	}
 
-	return -ETIMEDOUT;
+out:
+	dur = jiffies - started;
+	if (dur > HZ)
+		ath10k_dbg(ar, ATH10K_DBG_BMI,
+			   "bmi cmd took: %lu jiffies (HZ: %d), rv: %d\n",
+			   dur, HZ, rv);
+	return rv;
 }
 
 /*
Signature · 7 lines
2.4.11


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#1 lore raw

PATCH 2/3 ath10k: Fix napi related crash when otp fails.

In reply to [email protected]

From: Ben Greear <[email protected]>

The failure case is something like this:

otp fails (probably because BMI timeout was too short)
so core_start fails
so the entire firmware load fails..but since it was not ever started properly, then it is not stopped as far as PCI is concerned. So, napi is not released.

A bit later, maybe, the driver succeeds in loading and then we have a BUG splat.

------------[ cut here ]------------
kernel BUG at /home/greearb/git/linux-4.9.dev.y/include/linux/netdevice.h:515!
invalid opcode: 0000 [#1] PREEMPT SMP
Modules linked in: nf_conntrack_netlink nf_conntrack nfnetlink nf_defrag_ipv4 bridge ath10k_pci ath10k_core 8021q garp mrp stp llc bnep bluetooth fuse macv]
CPU: 1 PID: 3651 Comm: wpa_supplicant Not tainted 4.9.27+ #35
Hardware name: To be filled by O.E.M. To be filled by O.E.M./ChiefRiver, BIOS 4.6.5 06/07/2013
task: ffff8802111f0000 task.stack: ffffc90001fb4000
RIP: 0010:[<ffffffffa1498d33>]  [<ffffffffa1498d33>] ath10k_pci_hif_power_up+0x173/0x180 [ath10k_pci]
RSP: 0018:ffffc90001fb7c30  EFLAGS: 00010246
RAX: 0000000000000008 RBX: ffff880212bc2bc0 RCX: 0000000000082004
RDX: ffffc9000d282000 RSI: ffffc9000d282000 RDI: 000000000fd0a000
RBP: ffffc90001fb7c40 R08: 0000000000200000 R09: 0000000000000101
R10: 0000000000000d00 R11: 0000000000000003 R12: 0000000000082000
R13: ffff880212beaef8 R14: 0000000000000000 R15: ffff8802134c1118
FS:  00007f476575c800(0000) GS:ffff88021e240000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3da950b490 CR3: 0000000212b5a000 CR4: 00000000001406e0
Stack:
 ffff880212bc2bc0 ffff880212bc0700 ffffc90001fb7c68 ffffffffa1429281
 ffff8802134c0000 ffff880212bc0700 0000000000000000 ffffc90001fb7c90
 ffffffffa07cb818 ffff8802134c0000 ffff880212bc0700 0000000000000000
Call Trace:
 [<ffffffffa1429281>] ath10k_start+0x51/0x5c0 [ath10k_core]
 [<ffffffffa07cb818>] drv_start+0x38/0x140 [mac80211]
 [<ffffffffa07e2cc5>] ieee80211_do_open+0x2c5/0x990 [mac80211]
 [<ffffffffa07e33e0>] ieee80211_open+0x50/0x60 [mac80211]
 [<ffffffff817a9f2a>] __dev_open+0xaa/0x120
 [<ffffffff817aa208>] __dev_change_flags+0x98/0x160
 [<ffffffff817aa2f4>] dev_change_flags+0x24/0x60
 [<ffffffff8182388e>] devinet_ioctl+0x5ee/0x6c0
 [<ffffffff8182535b>] inet_ioctl+0x4b/0x70
 [<ffffffff81787430>] sock_do_ioctl+0x20/0x50
 [<ffffffff81787936>] sock_ioctl+0x1d6/0x2a0
 [<ffffffff8128d24b>] do_vfs_ioctl+0x8b/0x5b0
 [<ffffffff8178adbd>] ? __sys_recvmsg+0x3d/0x70
 [<ffffffff8128d7e4>] SyS_ioctl+0x74/0x80
 [<ffffffff8188a83b>] entry_SYSCALL_64_fastpath+0x1e/0xad
Code: ff ff ff 89 c2 48 89 df 48 c7 c6 10 d3 49 a1 e8 34 1d f9 ff 48 89 df e8 2c f9 ff ff 44 89 e0 c6 83 0e 74 02 00 01 5b 41 5c 5d c3 <0f> 0b 66 66 2e 0f
RIP  [<ffffffffa1498d33>] ath10k_pci_hif_power_up+0x173/0x180 [ath10k_pci]
 RSP <ffffc90001fb7c30>
---[ end trace b6dede286ed70e39 ]---

The BUG in question is this:

/**
* napi_enable - enable NAPI scheduling
* @n: NAPI context
*
* Resume NAPI from being scheduled on this context.
* Must be paired with napi_disable.
*/
static inline void napi_enable(struct napi_struct *n)

{
        BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
        smp_mb__before_atomic();
        clear_bit(NAPI_STATE_SCHED, &n->state);
        clear_bit(NAPI_STATE_NPSVC, &n->state);
}
---
 drivers/net/wireless/ath/ath10k/core.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/net/wireless/ath/ath10k/core.c +7 -3
index a715677..ad544b2 100644
@@ -1806,7 +1806,7 @@ static int ath10k_core_pre_cal_config(struct ath10k *ar)
 
 	ret = ath10k_download_and_run_otp(ar);
 	if (ret) {
-		ath10k_err(ar, "failed to run otp: %d\n", ret);
+		ath10k_err(ar, "failed to run otp: %d  (pre-cal-config)\n", ret);
 		return ret;
 	}
 
@@ -1860,7 +1860,7 @@ static int ath10k_download_cal_data(struct ath10k *ar)
 
 	ret = ath10k_download_and_run_otp(ar);
 	if (ret) {
-		ath10k_err(ar, "failed to run otp: %d\n", ret);
+		ath10k_err(ar, "failed to run otp: %d (download-cal-data)\n", ret);
 		return ret;
 	}
 
@@ -2783,7 +2783,11 @@ static void ath10k_core_register_work(struct work_struct *work)
 
 	status = ath10k_core_probe_fw(ar);
 	if (status) {
-		ath10k_err(ar, "could not probe fw (%d)\n", status);
+		ath10k_err(ar, "could not probe fw (%d), releasing napi\n", status);
+		/* Make sure that NAPI state is cleaned up, it can otherwise fail
+		 * to be cleaned up in some error cases.
+		 */
+		napi_disable(&ar->napi);
 		goto err;
 	}
 
Signature · 7 lines
2.4.11


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#2 lore raw

Re: [2/3] ath10k: Fix napi related crash when otp fails.

Quoted 63 lines · Ben Greear

The failure case is something like this:

otp fails (probably because BMI timeout was too short)
so core_start fails
so the entire firmware load fails..but since it was not ever started properly, then it is not stopped as far as PCI is concerned. So, napi is not released.

A bit later, maybe, the driver succeeds in loading and then we have a BUG splat.

------------[ cut here ]------------
kernel BUG at /home/greearb/git/linux-4.9.dev.y/include/linux/netdevice.h:515!
invalid opcode: 0000 [#1] PREEMPT SMP
Modules linked in: nf_conntrack_netlink nf_conntrack nfnetlink nf_defrag_ipv4 bridge ath10k_pci ath10k_core 8021q garp mrp stp llc bnep bluetooth fuse macv]
CPU: 1 PID: 3651 Comm: wpa_supplicant Not tainted 4.9.27+ #35
Hardware name: To be filled by O.E.M. To be filled by O.E.M./ChiefRiver, BIOS 4.6.5 06/07/2013
task: ffff8802111f0000 task.stack: ffffc90001fb4000
RIP: 0010:[<ffffffffa1498d33>]  [<ffffffffa1498d33>] ath10k_pci_hif_power_up+0x173/0x180 [ath10k_pci]
RSP: 0018:ffffc90001fb7c30  EFLAGS: 00010246
RAX: 0000000000000008 RBX: ffff880212bc2bc0 RCX: 0000000000082004
RDX: ffffc9000d282000 RSI: ffffc9000d282000 RDI: 000000000fd0a000
RBP: ffffc90001fb7c40 R08: 0000000000200000 R09: 0000000000000101
R10: 0000000000000d00 R11: 0000000000000003 R12: 0000000000082000
R13: ffff880212beaef8 R14: 0000000000000000 R15: ffff8802134c1118
FS:  00007f476575c800(0000) GS:ffff88021e240000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3da950b490 CR3: 0000000212b5a000 CR4: 00000000001406e0
Stack:
 ffff880212bc2bc0 ffff880212bc0700 ffffc90001fb7c68 ffffffffa1429281
 ffff8802134c0000 ffff880212bc0700 0000000000000000 ffffc90001fb7c90
 ffffffffa07cb818 ffff8802134c0000 ffff880212bc0700 0000000000000000
Call Trace:
 [<ffffffffa1429281>] ath10k_start+0x51/0x5c0 [ath10k_core]
 [<ffffffffa07cb818>] drv_start+0x38/0x140 [mac80211]
 [<ffffffffa07e2cc5>] ieee80211_do_open+0x2c5/0x990 [mac80211]
 [<ffffffffa07e33e0>] ieee80211_open+0x50/0x60 [mac80211]
 [<ffffffff817a9f2a>] __dev_open+0xaa/0x120
 [<ffffffff817aa208>] __dev_change_flags+0x98/0x160
 [<ffffffff817aa2f4>] dev_change_flags+0x24/0x60
 [<ffffffff8182388e>] devinet_ioctl+0x5ee/0x6c0
 [<ffffffff8182535b>] inet_ioctl+0x4b/0x70
 [<ffffffff81787430>] sock_do_ioctl+0x20/0x50
 [<ffffffff81787936>] sock_ioctl+0x1d6/0x2a0
 [<ffffffff8128d24b>] do_vfs_ioctl+0x8b/0x5b0
 [<ffffffff8178adbd>] ? __sys_recvmsg+0x3d/0x70
 [<ffffffff8128d7e4>] SyS_ioctl+0x74/0x80
 [<ffffffff8188a83b>] entry_SYSCALL_64_fastpath+0x1e/0xad
Code: ff ff ff 89 c2 48 89 df 48 c7 c6 10 d3 49 a1 e8 34 1d f9 ff 48 89 df e8 2c f9 ff ff 44 89 e0 c6 83 0e 74 02 00 01 5b 41 5c 5d c3 <0f> 0b 66 66 2e 0f
RIP  [<ffffffffa1498d33>] ath10k_pci_hif_power_up+0x173/0x180 [ath10k_pci]
 RSP <ffffc90001fb7c30>
---[ end trace b6dede286ed70e39 ]---

The BUG in question is this:

/**
* napi_enable - enable NAPI scheduling
* @n: NAPI context
*
* Resume NAPI from being scheduled on this context.
* Must be paired with napi_disable.
*/
static inline void napi_enable(struct napi_struct *n)

Quoted 8 lines
{
        BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
        smp_mb__before_atomic();
        clear_bit(NAPI_STATE_SCHED, &n->state);
        clear_bit(NAPI_STATE_NPSVC, &n->state);
}

Doesn't the commit below fix this?

commit 1427228d5869f5804b03d47acfa4a88122572a78

Author: Kalle Valo <[email protected]>
Date:   Mon Feb 13 12:38:39 2017 +0200

ath10k: fix napi crash during rmmod when probe firmware fails

Signature · 9 lines
https://patchwork.kernel.org/patch/9727993/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#6 lore raw

Re: [3/3] ath10k: Log when longer bmi cmds happen.

In reply to [email protected]
Quoted 5 lines · Ben Greear

This lets one have a clue that maybe timeouts are happening when we just aren't waiting long enough.

I did some cosmetic changes and ret is now initialised after the loop:

https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git/commit/?h=pending&id=13e31da60b738512ab1ac4429789d79a983ae5be

Signature · 9 lines
https://patchwork.kernel.org/patch/9727991/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author
#7 lore raw

Re: [3/3] ath10k: Log when longer bmi cmds happen.

Quoted 11 lines · Kalle Valo
Quoted 5 lines · Ben Greear

This lets one have a clue that maybe timeouts are happening when we just aren't waiting long enough.

I did some cosmetic changes and ret is now initialised after the loop:

https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git/commit/?h=pending&id=13e31da60b738512ab1ac4429789d79a983ae5be

Looks OK to me.

Thanks,
Ben

Signature · 7 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author
#3 lore raw

Re: [2/3] ath10k: Fix napi related crash when otp fails.

In reply to Kalle Valo
Quoted 72 lines · Kalle Valo
Quoted 70 lines · Ben Greear

The failure case is something like this:

otp fails (probably because BMI timeout was too short)
so core_start fails
so the entire firmware load fails..but since it was not ever started properly, then it is not stopped as far as PCI is concerned. So, napi is not released.

A bit later, maybe, the driver succeeds in loading and then we have a BUG splat.

------------[ cut here ]------------
kernel BUG at /home/greearb/git/linux-4.9.dev.y/include/linux/netdevice.h:515!
invalid opcode: 0000 [#1] PREEMPT SMP
Modules linked in: nf_conntrack_netlink nf_conntrack nfnetlink nf_defrag_ipv4 bridge ath10k_pci ath10k_core 8021q garp mrp stp llc bnep bluetooth fuse macv]
CPU: 1 PID: 3651 Comm: wpa_supplicant Not tainted 4.9.27+ #35
Hardware name: To be filled by O.E.M. To be filled by O.E.M./ChiefRiver, BIOS 4.6.5 06/07/2013
task: ffff8802111f0000 task.stack: ffffc90001fb4000
RIP: 0010:[<ffffffffa1498d33>]  [<ffffffffa1498d33>] ath10k_pci_hif_power_up+0x173/0x180 [ath10k_pci]
RSP: 0018:ffffc90001fb7c30  EFLAGS: 00010246
RAX: 0000000000000008 RBX: ffff880212bc2bc0 RCX: 0000000000082004
RDX: ffffc9000d282000 RSI: ffffc9000d282000 RDI: 000000000fd0a000
RBP: ffffc90001fb7c40 R08: 0000000000200000 R09: 0000000000000101
R10: 0000000000000d00 R11: 0000000000000003 R12: 0000000000082000
R13: ffff880212beaef8 R14: 0000000000000000 R15: ffff8802134c1118
FS:  00007f476575c800(0000) GS:ffff88021e240000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3da950b490 CR3: 0000000212b5a000 CR4: 00000000001406e0
Stack:
 ffff880212bc2bc0 ffff880212bc0700 ffffc90001fb7c68 ffffffffa1429281
 ffff8802134c0000 ffff880212bc0700 0000000000000000 ffffc90001fb7c90
 ffffffffa07cb818 ffff8802134c0000 ffff880212bc0700 0000000000000000
Call Trace:
 [<ffffffffa1429281>] ath10k_start+0x51/0x5c0 [ath10k_core]
 [<ffffffffa07cb818>] drv_start+0x38/0x140 [mac80211]
 [<ffffffffa07e2cc5>] ieee80211_do_open+0x2c5/0x990 [mac80211]
 [<ffffffffa07e33e0>] ieee80211_open+0x50/0x60 [mac80211]
 [<ffffffff817a9f2a>] __dev_open+0xaa/0x120
 [<ffffffff817aa208>] __dev_change_flags+0x98/0x160
 [<ffffffff817aa2f4>] dev_change_flags+0x24/0x60
 [<ffffffff8182388e>] devinet_ioctl+0x5ee/0x6c0
 [<ffffffff8182535b>] inet_ioctl+0x4b/0x70
 [<ffffffff81787430>] sock_do_ioctl+0x20/0x50
 [<ffffffff81787936>] sock_ioctl+0x1d6/0x2a0
 [<ffffffff8128d24b>] do_vfs_ioctl+0x8b/0x5b0
 [<ffffffff8178adbd>] ? __sys_recvmsg+0x3d/0x70
 [<ffffffff8128d7e4>] SyS_ioctl+0x74/0x80
 [<ffffffff8188a83b>] entry_SYSCALL_64_fastpath+0x1e/0xad
Code: ff ff ff 89 c2 48 89 df 48 c7 c6 10 d3 49 a1 e8 34 1d f9 ff 48 89 df e8 2c f9 ff ff 44 89 e0 c6 83 0e 74 02 00 01 5b 41 5c 5d c3 <0f> 0b 66 66 2e 0f
RIP  [<ffffffffa1498d33>] ath10k_pci_hif_power_up+0x173/0x180 [ath10k_pci]
 RSP <ffffc90001fb7c30>
---[ end trace b6dede286ed70e39 ]---

The BUG in question is this:

/**
* napi_enable - enable NAPI scheduling
* @n: NAPI context
*
* Resume NAPI from being scheduled on this context.
* Must be paired with napi_disable.
*/
static inline void napi_enable(struct napi_struct *n)

{
        BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
        smp_mb__before_atomic();
        clear_bit(NAPI_STATE_SCHED, &n->state);
        clear_bit(NAPI_STATE_NPSVC, &n->state);
}
Quoted 3 lines
Quoted 1 line

Doesn't the commit below fix this?

I don't know, but the problem in my case is that napi wasn't properly stopped, and the patch you reference is just about starting napi earlier, right?

I do think you should make the effort to provide such important
fixes to stable trees...if you had, then it would have been in my 4.9 tree already and it would have either fixed the problem or I would know for certain it was needed.

Thanks,
Ben

Signature · 7 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#8 lore raw
In reply to [email protected]
Quoted 4 lines · Ben Greear

When testing a 9888 chipset NIC, I notice it often takes almost 2 seconds, and then many times OTP fails, probably due to the two-second timeout.

Quoted 8 lines
[ 2269.841842] ath10k_pci 0000:05:00.0: bmi cmd took: 1984 jiffies (HZ: 1000), rv: 0
[ 2273.608185] ath10k_pci 0000:05:00.0: bmi cmd took: 1986 jiffies (HZ: 1000), rv: 0
[ 2277.294732] ath10k_pci 0000:05:00.0: bmi cmd took: 1989 jiffies (HZ: 1000), rv: 0

So, increase the BMI timeout to 3 seconds.

2 patches applied to ath-next branch of ath.git, thanks.

13c3b26a71df ath10k: increase BMI timeout 6bb099b088c7 ath10k: log when longer bmi cmds happen

Signature · 9 lines
https://patchwork.kernel.org/patch/9727989/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#4 lore raw

Re: [2/3] ath10k: Fix napi related crash when otp fails.

In reply to Ben Greear
Quoted 4 lines · Ben Greear
Quoted 1 line

Doesn't the commit below fix this?

I don't know, but the problem in my case is that napi wasn't properly stopped, and the patch you reference is just about starting napi earlier, right?

IIRC I moved it to a different function which was called later. This was just to match the symmetry with napi_disable() and fix the error handling.

Signature · 5 lines
Kalle Valo
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k