Skip to contentSkip to conversation

Patch "serial: exar: Fix stuck MSIs" has been added to the 4.11-stable tree

PATCH [email protected] 1 participant 1 message Jun 9, 2017

Subsystems (2)
lore
Share & tools
lore

[email protected]

author maintainer Applied
#0 lore raw

This is a note to let you know that I've just added the patch titled

serial: exar: Fix stuck MSIs

to the 4.11-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
serial-exar-fix-stuck-msis.patch
and it can be found in the queue-4.11 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree, please let <[email protected]> know about it.

Quoted 1 line

From 2c0ac5b48a3586f612b85755b041ed7733dc8e6b Mon Sep 17 00:00:00 2001

From: Jan Kiszka <[email protected]>
Date: Mon, 24 Apr 2017 12:30:15 +0200
Subject: serial: exar: Fix stuck MSIs

From: Jan Kiszka <[email protected]>

commit 2c0ac5b48a3586f612b85755b041ed7733dc8e6b upstream.

After migrating 8250_exar to MSI in 172c33cb61da, we can get stuck without further interrupts because of the special wake-up event these chips send. They are only cleared by reading INT0. As we fail to do so during startup and shutdown, we can leave the interrupt line asserted, which is fatal with edge-triggered MSIs.

Add the required reading of INT0 to startup and shutdown. Also account for the fact that a pending wake-up interrupt means we have to return 1 from exar_handle_irq. Drop the unneeded reading of INT1..3 along with this - those never reset anything.

An alternative approach would have been disabling the wake-up interrupt. Unfortunately, this feature (REGB[17] = 1) is not available on the XR17D15X.

Fixes 172c33cb61da ("serial: exar: Enable MSI support")
---
 drivers/tty/serial/8250/8250_port.c |   19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)
drivers/tty/serial/8250/8250_port.c +10 -9
@@ -47,6 +47,7 @@
 /*
  * These are definitions for the Exar XR17V35X and XR17(C|D)15X
  */
+#define UART_EXAR_INT0		0x80
 #define UART_EXAR_SLEEP		0x8b	/* Sleep mode */
 #define UART_EXAR_DVID		0x8d	/* Device identification */
 
@@ -1869,17 +1870,13 @@ static int serial8250_default_handle_irq
 static int exar_handle_irq(struct uart_port *port)
 {
 	unsigned int iir = serial_port_in(port, UART_IIR);
-	int ret;
+	int ret = 0;
 
-	ret = serial8250_handle_irq(port, iir);
+	if (((port->type == PORT_XR17V35X) || (port->type == PORT_XR17D15X)) &&
+	    serial_port_in(port, UART_EXAR_INT0) != 0)
+		ret = 1;
 
-	if ((port->type == PORT_XR17V35X) ||
-	   (port->type == PORT_XR17D15X)) {
-		serial_port_in(port, 0x80);
-		serial_port_in(port, 0x81);
-		serial_port_in(port, 0x82);
-		serial_port_in(port, 0x83);
-	}
+	ret |= serial8250_handle_irq(port, iir);
 
 	return ret;
 }
@@ -2177,6 +2174,8 @@ int serial8250_do_startup(struct uart_po
 	serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
+	if ((port->type == PORT_XR17V35X) || (port->type == PORT_XR17D15X))
+		serial_port_in(port, UART_EXAR_INT0);
 
 	/*
 	 * At this point, there's no way the LSR could still be 0xff;
@@ -2335,6 +2334,8 @@ dont_test_tx_en:
 	serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
+	if ((port->type == PORT_XR17V35X) || (port->type == PORT_XR17D15X))
+		serial_port_in(port, UART_EXAR_INT0);
 	up->lsr_saved_flags = 0;
 	up->msr_saved_flags = 0;
 

Patches currently in stable-queue which might be from [email protected] are

queue-4.11/serial-exar-fix-stuck-msis.patch